| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2023, Linaro Limited |
| */ |
| |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/spmi/spmi.h> |
| |
| / { |
| thermal-zones { |
| pmm8654au_0_thermal: pm8775-0-thermal { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmm8654au_0_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <105000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| pmm8654au_1_thermal: pm8775-1-thermal { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmm8654au_1_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <105000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| pmm8654au_2_thermal: pm8775-2-thermal { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmm8654au_2_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <105000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| pmm8654au_3_thermal: pm8775-3-thermal { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmm8654au_3_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <105000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| |
| reboot-mode { |
| compatible = "nvmem-reboot-mode"; |
| nvmem-cells = <&reboot_reason>; |
| nvmem-cell-names = "reboot-mode"; |
| mode-recovery = <0x01>; |
| mode-bootloader = <0x02>; |
| }; |
| }; |
| |
| &spmi_bus { |
| pmm8654au_0: pmic@0 { |
| compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmm8654au_0_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts-extended = <&spmi_bus 0x0 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmm8654au_0_pon: pon@1200 { |
| compatible = "qcom,pmk8350-pon"; |
| reg = <0x1200>, <0x800>; |
| reg-names = "hlos", "pbs"; |
| |
| pmm8654au_0_pon_pwrkey: pwrkey { |
| compatible = "qcom,pmk8350-pwrkey"; |
| interrupts-extended = <&spmi_bus 0x0 0x12 0x7 IRQ_TYPE_EDGE_BOTH>; |
| linux,code = <KEY_POWER>; |
| debounce = <15625>; |
| }; |
| |
| pmm8654au_0_pon_resin: resin { |
| compatible = "qcom,pmk8350-resin"; |
| interrupts-extended = <&spmi_bus 0x0 0x12 0x6 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| status = "disabled"; |
| }; |
| }; |
| |
| pmm8654au_0_gpios: gpio@8800 { |
| compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmm8654au_0_gpios 0 0 12>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| pmm8654au_0_sdam_0: nvram@7100 { |
| compatible = "qcom,spmi-sdam"; |
| reg = <0x7100>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x7100 0x100>; |
| |
| reboot_reason: reboot-reason@48 { |
| reg = <0x48 0x1>; |
| bits = <1 7>; |
| }; |
| }; |
| }; |
| |
| pmm8654au_1: pmic@2 { |
| compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; |
| reg = <0x2 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmm8654au_1_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmm8654au_1_gpios: gpio@8800 { |
| compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmm8654au_1_gpios 0 0 12>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmm8654au_2: pmic@4 { |
| compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; |
| reg = <0x4 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmm8654au_2_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts-extended = <&spmi_bus 0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmm8654au_2_gpios: gpio@8800 { |
| compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmm8654au_2_gpios 0 0 12>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmm8654au_3: pmic@6 { |
| compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; |
| reg = <0x6 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmm8654au_3_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmm8654au_3_gpios: gpio@8800 { |
| compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmm8654au_3_gpios 0 0 12>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| }; |
