| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2022, Linaro Limited |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h> |
| #include <dt-bindings/iio/qcom,spmi-adc7-pm8350b.h> |
| #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> |
| #include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h> |
| #include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h> |
| #include "sm8450.dtsi" |
| #include "pm8350.dtsi" |
| #include "pm8350b.dtsi" |
| #include "pm8350c.dtsi" |
| #include "pm8450.dtsi" |
| #include "pmk8350.dtsi" |
| #include "pmr735a.dtsi" |
| |
| / { |
| model = "Qualcomm Technologies, Inc. SM8450 HDK"; |
| compatible = "qcom,sm8450-hdk", "qcom,sm8450"; |
| chassis-type = "embedded"; |
| |
| aliases { |
| serial0 = &uart7; |
| }; |
| |
| wcd938x: audio-codec { |
| compatible = "qcom,wcd9385-codec"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wcd_default>; |
| |
| qcom,micbias1-microvolt = <1800000>; |
| qcom,micbias2-microvolt = <1800000>; |
| qcom,micbias3-microvolt = <1800000>; |
| qcom,micbias4-microvolt = <1800000>; |
| qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; |
| qcom,mbhc-headset-vthreshold-microvolt = <1700000>; |
| qcom,mbhc-headphone-vthreshold-microvolt = <50000>; |
| qcom,rx-device = <&wcd_rx>; |
| qcom,tx-device = <&wcd_tx>; |
| |
| reset-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>; |
| |
| vdd-buck-supply = <&vreg_s10b_1p8>; |
| vdd-rxtx-supply = <&vreg_s10b_1p8>; |
| vdd-io-supply = <&vreg_s10b_1p8>; |
| vdd-mic-bias-supply = <&vreg_bob>; |
| |
| #sound-dai-cells = <1>; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| hdmi-out { |
| compatible = "hdmi-connector"; |
| type = "a"; |
| |
| port { |
| hdmi_connector_out: endpoint { |
| remote-endpoint = <<9611_out>; |
| }; |
| }; |
| }; |
| |
| lt9611_1v2: lt9611-vdd12-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "LT9611_1V2"; |
| |
| vin-supply = <&vph_pwr>; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| lt9611_3v3: lt9611-3v3-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "LT9611_3V3"; |
| |
| vin-supply = <&vreg_bob>; |
| gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| enable-active-high; |
| }; |
| |
| pmic-glink { |
| compatible = "qcom,sm8450-pmic-glink", "qcom,pmic-glink"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| connector@0 { |
| compatible = "usb-c-connector"; |
| reg = <0>; |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_hs_in: endpoint { |
| remote-endpoint = <&usb_1_dwc3_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_ss_in: endpoint { |
| remote-endpoint = <&usb_1_qmpphy_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| pmic_glink_sbu: endpoint { |
| remote-endpoint = <&fsa4480_sbu_mux>; |
| }; |
| }; |
| |
| }; |
| }; |
| }; |
| |
| thermal-zones { |
| camera-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmk8350_adc_tm 2>; |
| |
| trips { |
| active-config0 { |
| temperature = <75000>; |
| hysteresis = <4000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| rear-tof-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmk8350_adc_tm 5>; |
| |
| trips { |
| active-config0 { |
| temperature = <75000>; |
| hysteresis = <4000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| skin-msm-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmk8350_adc_tm 1>; |
| |
| trips { |
| active-config0 { |
| temperature = <75000>; |
| hysteresis = <4000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| therm1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmk8350_adc_tm 3>; |
| |
| trips { |
| active-config0 { |
| temperature = <75000>; |
| hysteresis = <4000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| therm2-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmk8350_adc_tm 6>; |
| |
| trips { |
| active-config0 { |
| temperature = <75000>; |
| hysteresis = <4000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| usb-conn-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmk8350_adc_tm 7>; |
| |
| trips { |
| active-config0 { |
| temperature = <75000>; |
| hysteresis = <4000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| wide-rfc-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmk8350_adc_tm 4>; |
| |
| trips { |
| active-config0 { |
| temperature = <75000>; |
| hysteresis = <4000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| xo-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmk8350_adc_tm 0>; |
| |
| trips { |
| active-config0 { |
| temperature = <50000>; |
| hysteresis = <4000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm8350-rpmh-regulators"; |
| qcom,pmic-id = "b"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| vdd-s7-supply = <&vph_pwr>; |
| vdd-s8-supply = <&vph_pwr>; |
| vdd-s9-supply = <&vph_pwr>; |
| vdd-s10-supply = <&vph_pwr>; |
| vdd-s11-supply = <&vph_pwr>; |
| vdd-s12-supply = <&vph_pwr>; |
| |
| vdd-l1-l4-supply = <&vreg_s11b_0p95>; |
| vdd-l2-l7-supply = <&vreg_bob>; |
| vdd-l3-l5-supply = <&vreg_bob>; |
| vdd-l6-l9-l10-supply = <&vreg_s12b_1p25>; |
| vdd-l8-supply = <&vreg_s2h_0p95>; |
| |
| vreg_s10b_1p8: smps10 { |
| regulator-name = "vreg_s10b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vreg_s11b_0p95: smps11 { |
| regulator-name = "vreg_s11b_0p95"; |
| regulator-min-microvolt = <966000>; |
| regulator-max-microvolt = <1104000>; |
| }; |
| |
| vreg_s12b_1p25: smps12 { |
| regulator-name = "vreg_s12b_1p25"; |
| regulator-min-microvolt = <1350000>; |
| regulator-max-microvolt = <1400000>; |
| }; |
| |
| vreg_l1b_0p91: ldo1 { |
| regulator-name = "vreg_l1b_0p91"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2b_3p07: ldo2 { |
| regulator-name = "vreg_l2b_3p07"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3b_0p9: ldo3 { |
| regulator-name = "vreg_l3b_0p9"; |
| regulator-min-microvolt = <904000>; |
| regulator-max-microvolt = <904000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5b_0p88: ldo5 { |
| regulator-name = "vreg_l5b_0p88"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <888000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6b_1p2: ldo6 { |
| regulator-name = "vreg_l6b_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7b_2p5: ldo7 { |
| regulator-name = "vreg_l7b_2p5"; |
| regulator-min-microvolt = <2504000>; |
| regulator-max-microvolt = <2504000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9b_1p2: ldo9 { |
| regulator-name = "vreg_l9b_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm8350c-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| vdd-s7-supply = <&vph_pwr>; |
| vdd-s8-supply = <&vph_pwr>; |
| vdd-s9-supply = <&vph_pwr>; |
| vdd-s10-supply = <&vph_pwr>; |
| |
| vdd-l1-l12-supply = <&vreg_bob>; |
| vdd-l2-l8-supply = <&vreg_bob>; |
| vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>; |
| vdd-l6-l9-l11-supply = <&vreg_bob>; |
| vdd-l10-supply = <&vreg_s12b_1p25>; |
| |
| vdd-bob-supply = <&vph_pwr>; |
| |
| vreg_s1c_1p86: smps1 { |
| regulator-name = "vreg_s1c_1p86"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2024000>; |
| }; |
| |
| vreg_s10c_1p05: smps10 { |
| regulator-name = "vreg_s10c_1p05"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1100000>; |
| }; |
| |
| vreg_bob: bob { |
| regulator-name = "vreg_bob"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; |
| }; |
| |
| vreg_l1c_1p8: ldo1 { |
| regulator-name = "vreg_l1c_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3c_3p0: ldo3 { |
| regulator-name = "vreg_l3c_3p0"; |
| regulator-min-microvolt = <3296000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4c_1p8: ldo4 { |
| regulator-name = "vreg_l4c_1p8"; |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5c_1p8: ldo5 { |
| regulator-name = "vreg_l5c_1p8"; |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6c_1p8: ldo6 { |
| regulator-name = "vreg_l6c_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7c_3p0: ldo7 { |
| regulator-name = "vreg_l7c_3p0"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8c_1p8: ldo8 { |
| regulator-name = "vreg_l8c_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9c_2p96: ldo9 { |
| regulator-name = "vreg_l9c_2p96"; |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12c_1p8: ldo12 { |
| regulator-name = "vreg_l12c_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1968000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13c_3p0: ldo13 { |
| regulator-name = "vreg_l13c_3p0"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-2 { |
| compatible = "qcom,pm8450-rpmh-regulators"; |
| qcom,pmic-id = "h"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| |
| vdd-l2-supply = <&vreg_bob>; |
| vdd-l3-supply = <&vreg_bob>; |
| vdd-l4-supply = <&vreg_bob>; |
| |
| vreg_s2h_0p95: smps2 { |
| regulator-name = "vreg_s2h_0p95"; |
| regulator-min-microvolt = <848000>; |
| regulator-max-microvolt = <1104000>; |
| }; |
| |
| vreg_s3h_0p5: smps3 { |
| regulator-name = "vreg_s3h_0p5"; |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <500000>; |
| }; |
| |
| vreg_l2h_0p91: ldo2 { |
| regulator-name = "vreg_l2h_0p91"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3h_0p91: ldo3 { |
| regulator-name = "vreg_l3h_0p91"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-3 { |
| compatible = "qcom,pmr735a-rpmh-regulators"; |
| qcom,pmic-id = "e"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| |
| vdd-l1-l2-supply = <&vreg_s2e_0p85>; |
| vdd-l3-supply = <&vreg_s1e_1p25>; |
| vdd-l4-supply = <&vreg_s1c_1p86>; |
| vdd-l5-l6-supply = <&vreg_s1c_1p86>; |
| vdd-l7-bob-supply = <&vreg_bob>; |
| |
| vreg_s1e_1p25: smps1 { |
| regulator-name = "vreg_s1e_1p25"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1296000>; |
| }; |
| |
| vreg_s2e_0p85: smps2 { |
| regulator-name = "vreg_s2e_0p85"; |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1040000>; |
| }; |
| |
| vreg_l1e_0p8: ldo1 { |
| regulator-name = "vreg_l1e_0p8"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| }; |
| |
| vreg_l2e_0p8: ldo2 { |
| regulator-name = "vreg_l2e_0p8"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| }; |
| |
| vreg_l3e_1p2: ldo3 { |
| regulator-name = "vreg_l3e_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| vreg_l4e_1p7: ldo4 { |
| regulator-name = "vreg_l4e_1p7"; |
| regulator-min-microvolt = <1776000>; |
| regulator-max-microvolt = <1776000>; |
| }; |
| |
| vreg_l5e_0p88: ldo5 { |
| regulator-name = "vreg_l5e_0p88"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| }; |
| |
| vreg_l6e_1p2: ldo6 { |
| regulator-name = "vreg_l6e_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| vreg_l7e_2p8: ldo7 { |
| regulator-name = "vreg_l7e_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| }; |
| }; |
| |
| &dispcc { |
| status = "okay"; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| firmware-name = "qcom/sm8450/a730_zap.mbn"; |
| }; |
| }; |
| |
| &i2c9 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| lt9611_codec: hdmi-bridge@2b { |
| compatible = "lontium,lt9611uxc"; |
| reg = <0x2b>; |
| |
| interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>; |
| |
| reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>; |
| |
| vdd-supply = <<9611_1v2>; |
| vcc-supply = <<9611_3v3>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <<9611_irq_pin <9611_rst_pin>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| lt9611_a: endpoint { |
| remote-endpoint = <&mdss_dsi0_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| lt9611_out: endpoint { |
| remote-endpoint = <&hdmi_connector_out>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c5 { |
| clock-frequency = <100000>; |
| |
| status = "okay"; |
| |
| typec-mux@42 { |
| compatible = "fcs,fsa4480"; |
| reg = <0x42>; |
| |
| interrupts-extended = <&tlmm 2 IRQ_TYPE_LEVEL_LOW>; |
| |
| vcc-supply = <&vreg_bob>; |
| mode-switch; |
| orientation-switch; |
| |
| port { |
| fsa4480_sbu_mux: endpoint { |
| remote-endpoint = <&pmic_glink_sbu>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dsi0 { |
| vdda-supply = <&vreg_l6b_1p2>; |
| status = "okay"; |
| }; |
| |
| &mdss_dsi0_out { |
| remote-endpoint = <<9611_a>; |
| data-lanes = <0 1 2 3>; |
| }; |
| |
| &mdss_dsi0_phy { |
| vdds-supply = <&vreg_l5b_0p88>; |
| status = "okay"; |
| }; |
| |
| &mdss_dp0 { |
| status = "okay"; |
| |
| ports { |
| port@1 { |
| reg = <1>; |
| |
| mdss_dp0_out: endpoint { |
| data-lanes = <0 1>; |
| remote-endpoint = <&usb_1_qmpphy_dp_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| &pcie0 { |
| status = "okay"; |
| max-link-speed = <2>; |
| }; |
| |
| &pcie0_phy { |
| status = "okay"; |
| vdda-phy-supply = <&vreg_l5b_0p88>; |
| vdda-pll-supply = <&vreg_l6b_1p2>; |
| }; |
| |
| &pcie1 { |
| status = "okay"; |
| }; |
| |
| &pcie1_phy { |
| status = "okay"; |
| vdda-phy-supply = <&vreg_l2h_0p91>; |
| vdda-pll-supply = <&vreg_l6b_1p2>; |
| }; |
| |
| &pm8350_temp_alarm { |
| io-channels = <&pmk8350_vadc PM8350_ADC7_DIE_TEMP(1)>; |
| io-channel-names = "thermal"; |
| }; |
| |
| &pm8350b_temp_alarm { |
| io-channels = <&pmk8350_vadc PM8350B_ADC7_DIE_TEMP>; |
| io-channel-names = "thermal"; |
| }; |
| |
| &pmr735a_temp_alarm { |
| io-channels = <&pmk8350_vadc PMR735A_ADC7_DIE_TEMP>; |
| io-channel-names = "thermal"; |
| }; |
| |
| &pmk8350_adc_tm { |
| status = "okay"; |
| |
| xo-therm@0 { |
| reg = <0>; |
| io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| skin-msm-therm@1 { |
| reg = <1>; |
| io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| camera-therm@2 { |
| reg = <2>; |
| io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| therm1-therm@3 { |
| reg = <3>; |
| io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM3_100K_PU(1)>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| wide-rfc-therm@4 { |
| reg = <4>; |
| io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| rear-tof-therm@5 { |
| reg = <5>; |
| io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM5_100K_PU(1)>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| therm2-therm@6 { |
| reg = <6>; |
| io-channels = <&pmk8350_vadc PM8350_ADC7_GPIO3_100K_PU(1)>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| usb-conn-therm@7 { |
| reg = <7>; |
| io-channels = <&pmk8350_vadc PM8350B_ADC7_AMUX_THM5_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| }; |
| |
| &pmk8350_vadc { |
| status = "okay"; |
| |
| channel@3 { |
| reg = <PMK8350_ADC7_DIE_TEMP>; |
| label = "pmk8350_die_temp"; |
| }; |
| |
| channel@44 { |
| reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "pmk8350_xo_therm"; |
| }; |
| |
| channel@103 { |
| reg = <PM8350_ADC7_DIE_TEMP(1)>; |
| label = "pm8350_die_temp"; |
| }; |
| |
| channel@144 { |
| reg = <PM8350_ADC7_AMUX_THM1_100K_PU(1)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "skin_msm_temp"; |
| }; |
| |
| channel@145 { |
| reg = <PM8350_ADC7_AMUX_THM2_100K_PU(1)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "camera_temp"; |
| }; |
| |
| channel@146 { |
| reg = <PM8350_ADC7_AMUX_THM3_100K_PU(1)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "therm1_temp"; |
| }; |
| |
| channel@147 { |
| reg = <PM8350_ADC7_AMUX_THM4_100K_PU(1)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "wide_rfc_temp"; |
| }; |
| |
| channel@148 { |
| reg = <PM8350_ADC7_AMUX_THM5_100K_PU(1)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "rear_tof_temp"; |
| }; |
| |
| channel@14c { |
| reg = <PM8350_ADC7_GPIO3_100K_PU(1)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "therm2_temp"; |
| }; |
| |
| channel@303 { |
| reg = <PM8350B_ADC7_DIE_TEMP>; |
| label = "pm8350b_die_temp"; |
| }; |
| |
| channel@348 { |
| reg = <PM8350B_ADC7_AMUX_THM5_100K_PU>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "usb_conn_temp"; |
| }; |
| |
| channel@403 { |
| reg = <PMR735A_ADC7_DIE_TEMP>; |
| label = "pmr735a_die_temp"; |
| }; |
| |
| channel@44a { |
| reg = <PMR735A_ADC7_GPIO1_100K_PU>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "qtm_w_temp"; |
| }; |
| |
| channel@44b { |
| reg = <PMR735A_ADC7_GPIO2_100K_PU>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "qtm_n_temp"; |
| }; |
| }; |
| |
| &remoteproc_adsp { |
| status = "okay"; |
| firmware-name = "qcom/sm8450/adsp.mbn"; |
| }; |
| |
| &remoteproc_cdsp { |
| status = "okay"; |
| firmware-name = "qcom/sm8450/cdsp.mbn"; |
| }; |
| |
| &remoteproc_mpss { |
| status = "okay"; |
| firmware-name = "qcom/sm8450/modem.mbn"; |
| }; |
| |
| &remoteproc_slpi { |
| status = "okay"; |
| firmware-name = "qcom/sm8450/slpi.mbn"; |
| }; |
| |
| &qupv3_id_0 { |
| status = "okay"; |
| }; |
| |
| &qupv3_id_1 { |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>; |
| pinctrl-1 = <&sdc2_sleep_state &sdc2_card_det_n>; |
| vmmc-supply = <&vreg_l9c_2p96>; |
| vqmmc-supply = <&vreg_l6c_1p8>; |
| no-sdio; |
| no-mmc; |
| status = "okay"; |
| }; |
| |
| &sound { |
| compatible = "qcom,sm8450-sndcard"; |
| model = "SM8450-HDK"; |
| audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT", |
| "SpkrRight IN", "WSA_SPK2 OUT", |
| "IN1_HPHL", "HPHL_OUT", |
| "IN2_HPHR", "HPHR_OUT", |
| "AMIC1", "MIC BIAS1", |
| "AMIC2", "MIC BIAS2", |
| "AMIC3", "MIC BIAS3", |
| "AMIC4", "MIC BIAS3", |
| "AMIC5", "MIC BIAS4", |
| "VA DMIC0", "MIC BIAS3", |
| "VA DMIC1", "MIC BIAS3", |
| "VA DMIC2", "MIC BIAS1", |
| "VA DMIC3", "MIC BIAS1", |
| "TX DMIC0", "MIC BIAS3", |
| "TX DMIC1", "MIC BIAS3", |
| "TX DMIC2", "MIC BIAS1", |
| "TX DMIC3", "MIC BIAS1", |
| "TX SWR_INPUT0", "ADC1_OUTPUT", |
| "TX SWR_INPUT1", "ADC2_OUTPUT", |
| "TX SWR_INPUT0", "ADC3_OUTPUT", |
| "TX SWR_INPUT1", "ADC4_OUTPUT"; |
| |
| wcd-playback-dai-link { |
| link-name = "WCD Playback"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wcd-capture-dai-link { |
| link-name = "WCD Capture"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wsa-dai-link { |
| link-name = "WSA Playback"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| va-dai-link { |
| link-name = "VA Capture"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; |
| }; |
| |
| codec { |
| sound-dai = <&vamacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| }; |
| |
| &swr0 { |
| status = "okay"; |
| |
| left_spkr: speaker@0,1 { |
| compatible = "sdw10217020200"; |
| reg = <0 1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spkr_1_sd_n_active>; |
| powerdown-gpios = <&tlmm 1 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "SpkrLeft"; |
| #thermal-sensor-cells = <0>; |
| vdd-supply = <&vreg_s10b_1p8>; |
| }; |
| |
| right_spkr: speaker@0,2 { |
| compatible = "sdw10217020200"; |
| reg = <0 2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spkr_2_sd_n_active>; |
| powerdown-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "SpkrRight"; |
| #thermal-sensor-cells = <0>; |
| vdd-supply = <&vreg_s10b_1p8>; |
| }; |
| }; |
| |
| &swr1 { |
| status = "okay"; |
| |
| wcd_rx: codec@0,4 { |
| compatible = "sdw20217010d00"; |
| reg = <0 4>; |
| qcom,rx-port-mapping = <1 2 3 4 5>; |
| }; |
| }; |
| |
| &swr2 { |
| status = "okay"; |
| |
| wcd_tx: codec@0,3 { |
| compatible = "sdw20217010d00"; |
| reg = <0 3>; |
| qcom,tx-port-mapping = <1 1 2 3>; |
| }; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <28 4>, <36 4>; |
| |
| lt9611_irq_pin: lt9611-irq-state { |
| pins = "gpio44"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| lt9611_rst_pin: lt9611-rst-state { |
| pins = "gpio107"; |
| function = "gpio"; |
| output-high; |
| }; |
| |
| sdc2_card_det_n: sd-card-det-n-state { |
| pins = "gpio92"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| &uart7 { |
| status = "okay"; |
| }; |
| |
| &ufs_mem_hc { |
| status = "okay"; |
| |
| reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>; |
| |
| vcc-supply = <&vreg_l7b_2p5>; |
| vcc-max-microamp = <1100000>; |
| vccq-supply = <&vreg_l9b_1p2>; |
| vccq-max-microamp = <1200000>; |
| vdd-hba-supply = <&vreg_l9b_1p2>; |
| }; |
| |
| &ufs_mem_phy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l5b_0p88>; |
| vdda-pll-supply = <&vreg_l6b_1p2>; |
| }; |
| |
| &usb_1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_dwc3 { |
| dr_mode = "otg"; |
| usb-role-switch; |
| }; |
| |
| &usb_1_dwc3_hs { |
| remote-endpoint = <&pmic_glink_hs_in>; |
| }; |
| |
| &usb_1_dwc3_ss { |
| remote-endpoint = <&usb_1_qmpphy_usb_ss_in>; |
| }; |
| |
| &usb_1_hsphy { |
| status = "okay"; |
| |
| vdda-pll-supply = <&vreg_l5b_0p88>; |
| vdda18-supply = <&vreg_l1c_1p8>; |
| vdda33-supply = <&vreg_l2b_3p07>; |
| }; |
| |
| &usb_1_qmpphy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l6b_1p2>; |
| vdda-pll-supply = <&vreg_l1b_0p91>; |
| |
| orientation-switch; |
| }; |
| |
| &usb_1_qmpphy_dp_in { |
| remote-endpoint = <&mdss_dp0_out>; |
| }; |
| |
| &usb_1_qmpphy_out { |
| remote-endpoint = <&pmic_glink_ss_in>; |
| }; |
| |
| &usb_1_qmpphy_usb_ss_in { |
| remote-endpoint = <&usb_1_dwc3_ss>; |
| }; |
| |
| &vamacro { |
| pinctrl-0 = <&dmic01_default>, <&dmic23_default>; |
| pinctrl-names = "default"; |
| vdd-micb-supply = <&vreg_s10b_1p8>; |
| qcom,dmic-sample-rate = <600000>; |
| |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| spkr_1_sd_n_active: spkr-1-sd-n-active-state { |
| pins = "gpio1"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| |
| spkr_2_sd_n_active: spkr-2-sd-n-active-state { |
| pins = "gpio89"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| |
| wcd_default: wcd-reset-n-active-state { |
| pins = "gpio43"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| }; |
