| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2022, Linaro Limited |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include "sm8550.dtsi" |
| #include "pm8010.dtsi" |
| #include "pm8550.dtsi" |
| #include "pm8550b.dtsi" |
| #define PMK8550VE_SID 5 |
| #include "pm8550ve.dtsi" |
| #include "pm8550vs.dtsi" |
| #include "pmk8550.dtsi" |
| #include "pmr735d_a.dtsi" |
| #include "pmr735d_b.dtsi" |
| |
| / { |
| model = "Qualcomm Technologies, Inc. SM8550 MTP"; |
| compatible = "qcom,sm8550-mtp", "qcom,sm8550"; |
| chassis-type = "handset"; |
| |
| aliases { |
| serial0 = &uart7; |
| }; |
| |
| wcd938x: audio-codec { |
| compatible = "qcom,wcd9385-codec"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wcd_default>; |
| |
| qcom,micbias1-microvolt = <1800000>; |
| qcom,micbias2-microvolt = <1800000>; |
| qcom,micbias3-microvolt = <1800000>; |
| qcom,micbias4-microvolt = <1800000>; |
| qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; |
| qcom,mbhc-headset-vthreshold-microvolt = <1700000>; |
| qcom,mbhc-headphone-vthreshold-microvolt = <50000>; |
| qcom,rx-device = <&wcd_rx>; |
| qcom,tx-device = <&wcd_tx>; |
| |
| reset-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>; |
| |
| vdd-buck-supply = <&vreg_l15b_1p8>; |
| vdd-rxtx-supply = <&vreg_l15b_1p8>; |
| vdd-io-supply = <&vreg_l15b_1p8>; |
| vdd-mic-bias-supply = <&vreg_bob1>; |
| |
| #sound-dai-cells = <1>; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| pmic-glink { |
| compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; |
| |
| connector@0 { |
| compatible = "usb-c-connector"; |
| reg = <0>; |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_hs_in: endpoint { |
| remote-endpoint = <&usb_1_dwc3_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_ss_in: endpoint { |
| remote-endpoint = <&usb_dp_qmpphy_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| pmic_glink_sbu: endpoint { |
| remote-endpoint = <&fsa4480_sbu_mux>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| sound { |
| compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard"; |
| model = "SM8550-MTP"; |
| audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT", |
| "SpkrRight IN", "WSA_SPK2 OUT", |
| "IN1_HPHL", "HPHL_OUT", |
| "IN2_HPHR", "HPHR_OUT", |
| "AMIC1", "MIC BIAS1", |
| "AMIC2", "MIC BIAS2", |
| "AMIC3", "MIC BIAS3", |
| "AMIC4", "MIC BIAS3", |
| "AMIC5", "MIC BIAS4", |
| "VA DMIC0", "MIC BIAS1", |
| "VA DMIC1", "MIC BIAS1", |
| "VA DMIC2", "MIC BIAS3", |
| "TX DMIC0", "MIC BIAS1", |
| "TX DMIC1", "MIC BIAS2", |
| "TX DMIC2", "MIC BIAS3", |
| "TX SWR_INPUT0", "ADC1_OUTPUT", |
| "TX SWR_INPUT1", "ADC2_OUTPUT", |
| "TX SWR_INPUT0", "ADC3_OUTPUT", |
| "TX SWR_INPUT1", "ADC4_OUTPUT"; |
| |
| wcd-playback-dai-link { |
| link-name = "WCD Playback"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wcd-capture-dai-link { |
| link-name = "WCD Capture"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd938x 1>, <&swr2 0>, <&lpass_txmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wsa-dai-link { |
| link-name = "WSA Playback"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&lpass_wsamacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| va-dai-link { |
| link-name = "VA Capture"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; |
| }; |
| |
| codec { |
| sound-dai = <&lpass_vamacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm8550-rpmh-regulators"; |
| qcom,pmic-id = "b"; |
| |
| vdd-bob1-supply = <&vph_pwr>; |
| vdd-bob2-supply = <&vph_pwr>; |
| vdd-l1-l4-l10-supply = <&vreg_s6g_1p8>; |
| vdd-l2-l13-l14-supply = <&vreg_bob1>; |
| vdd-l3-supply = <&vreg_s4g_1p3>; |
| vdd-l5-l16-supply = <&vreg_bob1>; |
| vdd-l6-l7-supply = <&vreg_bob1>; |
| vdd-l8-l9-supply = <&vreg_bob1>; |
| vdd-l11-supply = <&vreg_s4g_1p3>; |
| vdd-l12-supply = <&vreg_s6g_1p8>; |
| vdd-l15-supply = <&vreg_s6g_1p8>; |
| vdd-l17-supply = <&vreg_bob2>; |
| |
| vreg_bob1: bob1 { |
| regulator-name = "vreg_bob1"; |
| regulator-min-microvolt = <3296000>; |
| regulator-max-microvolt = <3960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_bob2: bob2 { |
| regulator-name = "vreg_bob2"; |
| regulator-min-microvolt = <2720000>; |
| regulator-max-microvolt = <3960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1b_1p8: ldo1 { |
| regulator-name = "vreg_l1b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2b_3p0: ldo2 { |
| regulator-name = "vreg_l2b_3p0"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5b_3p1: ldo5 { |
| regulator-name = "vreg_l5b_3p1"; |
| regulator-min-microvolt = <3104000>; |
| regulator-max-microvolt = <3104000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6b_1p8: ldo6 { |
| regulator-name = "vreg_l6b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7b_1p8: ldo7 { |
| regulator-name = "vreg_l7b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8b_1p8: ldo8 { |
| regulator-name = "vreg_l8b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9b_2p9: ldo9 { |
| regulator-name = "vreg_l9b_2p9"; |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l11b_1p2: ldo11 { |
| regulator-name = "vreg_l11b_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1504000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12b_1p8: ldo12 { |
| regulator-name = "vreg_l12b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13b_3p0: ldo13 { |
| regulator-name = "vreg_l13b_3p0"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14b_3p2: ldo14 { |
| regulator-name = "vreg_l14b_3p2"; |
| regulator-min-microvolt = <3200000>; |
| regulator-max-microvolt = <3200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l15b_1p8: ldo15 { |
| regulator-name = "vreg_l15b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l16b_2p8: ldo16 { |
| regulator-name = "vreg_l16b_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l17b_2p5: ldo17 { |
| regulator-name = "vreg_l17b_2p5"; |
| regulator-min-microvolt = <2504000>; |
| regulator-max-microvolt = <2504000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm8550vs-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vdd-l3-supply = <&vreg_s4e_0p9>; |
| |
| vreg_l3c_0p91: ldo3 { |
| regulator-name = "vreg_l3c_0p9"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-2 { |
| compatible = "qcom,pm8550vs-rpmh-regulators"; |
| qcom,pmic-id = "d"; |
| |
| vdd-l1-supply = <&vreg_s4e_0p9>; |
| |
| vreg_l1d_0p88: ldo1 { |
| regulator-name = "vreg_l1d_0p88"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-3 { |
| compatible = "qcom,pm8550vs-rpmh-regulators"; |
| qcom,pmic-id = "e"; |
| |
| vdd-l1-supply = <&vreg_s4e_0p9>; |
| vdd-l2-supply = <&vreg_s4e_0p9>; |
| vdd-l3-supply = <&vreg_s4g_1p3>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| |
| vreg_s4e_0p9: smps4 { |
| regulator-name = "vreg_s4e_0p9"; |
| regulator-min-microvolt = <904000>; |
| regulator-max-microvolt = <984000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s5e_1p1: smps5 { |
| regulator-name = "vreg_s5e_1p1"; |
| regulator-min-microvolt = <1080000>; |
| regulator-max-microvolt = <1120000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1e_0p88: ldo1 { |
| regulator-name = "vreg_l1e_0p88"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2e_0p9: ldo2 { |
| regulator-name = "vreg_l2e_0p9"; |
| regulator-min-microvolt = <904000>; |
| regulator-max-microvolt = <970000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3e_1p2: ldo3 { |
| regulator-name = "vreg_l3e_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-4 { |
| compatible = "qcom,pm8550ve-rpmh-regulators"; |
| qcom,pmic-id = "f"; |
| |
| vdd-l1-supply = <&vreg_s4e_0p9>; |
| vdd-l2-supply = <&vreg_s4e_0p9>; |
| vdd-l3-supply = <&vreg_s4e_0p9>; |
| vdd-s4-supply = <&vph_pwr>; |
| |
| vreg_s4f_0p5: smps4 { |
| regulator-name = "vreg_s4f_0p5"; |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <700000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1f_0p9: ldo1 { |
| regulator-name = "vreg_l1f_0p9"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2f_0p88: ldo2 { |
| regulator-name = "vreg_l2f_0p88"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3f_0p91: ldo3 { |
| regulator-name = "vreg_l3f_0p91"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-5 { |
| compatible = "qcom,pm8550vs-rpmh-regulators"; |
| qcom,pmic-id = "g"; |
| |
| vdd-l1-supply = <&vreg_s4g_1p3>; |
| vdd-l2-supply = <&vreg_s4g_1p3>; |
| vdd-l3-supply = <&vreg_s4g_1p3>; |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| |
| vreg_s1g_1p2: smps1 { |
| regulator-name = "vreg_s1g_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s2g_0p8: smps2 { |
| regulator-name = "vreg_s2g_0p8"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s3g_0p7: smps3 { |
| regulator-name = "vreg_s3g_0p7"; |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1004000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s4g_1p3: smps4 { |
| regulator-name = "vreg_s4g_1p3"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1352000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s5g_0p8: smps5 { |
| regulator-name = "vreg_s5g_0p8"; |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1004000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s6g_1p8: smps6 { |
| regulator-name = "vreg_s6g_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1g_1p2: ldo1 { |
| regulator-name = "vreg_l1g_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2g_1p2: ldo2 { |
| regulator-name = "vreg_l2g_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3g_1p2: ldo3 { |
| regulator-name = "vreg_l3g_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-6 { |
| compatible = "qcom,pm8010-rpmh-regulators"; |
| qcom,pmic-id = "m"; |
| |
| vdd-l1-l2-supply = <&vreg_s4g_1p3>; |
| vdd-l3-l4-supply = <&vreg_bob2>; |
| vdd-l5-supply = <&vreg_s6g_1p8>; |
| vdd-l6-supply = <&vreg_s6g_1p8>; |
| vdd-l7-supply = <&vreg_bob1>; |
| |
| vreg_l1m_1p056: ldo1 { |
| regulator-name = "vreg_l1m_1p056"; |
| regulator-min-microvolt = <1056000>; |
| regulator-max-microvolt = <1056000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2m_1p056: ldo2 { |
| regulator-name = "vreg_l2m_1p056"; |
| regulator-min-microvolt = <1056000>; |
| regulator-max-microvolt = <1056000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3m_2p8: ldo3 { |
| regulator-name = "vreg_l3m_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4m_2p8: ldo4 { |
| regulator-name = "vreg_l4m_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5m_1p8: ldo5 { |
| regulator-name = "vreg_l5m_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6m_1p8: ldo6 { |
| regulator-name = "vreg_l6m_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7m_2p9: ldo7 { |
| regulator-name = "vreg_l7m_2p9"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2904000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-7 { |
| compatible = "qcom,pm8010-rpmh-regulators"; |
| qcom,pmic-id = "n"; |
| |
| vdd-l1-l2-supply = <&vreg_s4g_1p3>; |
| vdd-l3-l4-supply = <&vreg_bob2>; |
| vdd-l5-supply = <&vreg_s6g_1p8>; |
| vdd-l6-supply = <&vreg_bob1>; |
| vdd-l7-supply = <&vreg_bob1>; |
| |
| vreg_l1n_1p1: ldo1 { |
| regulator-name = "vreg_l1n_1p1"; |
| regulator-min-microvolt = <1104000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2n_1p1: ldo2 { |
| regulator-name = "vreg_l2n_1p1"; |
| regulator-min-microvolt = <1104000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3n_2p8: ldo3 { |
| regulator-name = "vreg_l3n_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4n_2p8: ldo4 { |
| regulator-name = "vreg_l4n_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5n_1p8: ldo5 { |
| regulator-name = "vreg_l5n_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6n_3p3: ldo6 { |
| regulator-name = "vreg_l6n_3p3"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7n_2p96: ldo7 { |
| regulator-name = "vreg_l7n_2p96"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| firmware-name = "qcom/sm8550/a740_zap.mbn"; |
| }; |
| }; |
| |
| &i2c_master_hub_0 { |
| status = "okay"; |
| }; |
| |
| &i2c_hub_2 { |
| status = "okay"; |
| |
| typec-mux@42 { |
| compatible = "fcs,fsa4480"; |
| reg = <0x42>; |
| |
| vcc-supply = <&vreg_bob1>; |
| |
| mode-switch; |
| orientation-switch; |
| |
| port { |
| fsa4480_sbu_mux: endpoint { |
| remote-endpoint = <&pmic_glink_sbu>; |
| }; |
| }; |
| }; |
| }; |
| |
| &lpass_tlmm { |
| spkr_1_sd_n_active: spkr-1-sd-n-active-state { |
| pins = "gpio17"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| |
| spkr_2_sd_n_active: spkr-2-sd-n-active-state { |
| pins = "gpio18"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dsi0 { |
| vdda-supply = <&vreg_l3e_1p2>; |
| status = "okay"; |
| |
| panel@0 { |
| compatible = "visionox,vtdr6130"; |
| reg = <0>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>; |
| pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>; |
| |
| vddio-supply = <&vreg_l12b_1p8>; |
| vci-supply = <&vreg_l13b_3p0>; |
| vdd-supply = <&vreg_l11b_1p2>; |
| |
| reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>; |
| |
| port { |
| panel0_in: endpoint { |
| remote-endpoint = <&mdss_dsi0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dsi0_out { |
| remote-endpoint = <&panel0_in>; |
| data-lanes = <0 1 2 3>; |
| }; |
| |
| &mdss_dsi0_phy { |
| vdds-supply = <&vreg_l1e_0p88>; |
| status = "okay"; |
| }; |
| |
| &mdss_dp0 { |
| status = "okay"; |
| }; |
| |
| &mdss_dp0_out { |
| data-lanes = <0 1>; |
| remote-endpoint = <&usb_dp_qmpphy_dp_in>; |
| }; |
| |
| &pcie_1_phy_aux_clk { |
| clock-frequency = <1000>; |
| }; |
| |
| &pcie0 { |
| wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; |
| perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie0_default_state>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie0_phy { |
| vdda-phy-supply = <&vreg_l1e_0p88>; |
| vdda-pll-supply = <&vreg_l3e_1p2>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie1 { |
| wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>; |
| perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie1_default_state>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie1_phy { |
| vdda-phy-supply = <&vreg_l3c_0p91>; |
| vdda-pll-supply = <&vreg_l3e_1p2>; |
| vdda-qref-supply = <&vreg_l1e_0p88>; |
| |
| status = "okay"; |
| }; |
| |
| &pm8550_gpios { |
| sdc2_card_det_n: sdc2-card-det-state { |
| pins = "gpio12"; |
| function = "normal"; |
| input-enable; |
| output-disable; |
| bias-pull-up; |
| power-source = <1>; /* 1.8 V */ |
| }; |
| }; |
| |
| &pm8550b_eusb2_repeater { |
| vdd18-supply = <&vreg_l15b_1p8>; |
| vdd3-supply = <&vreg_l5b_3p1>; |
| }; |
| |
| &qupv3_id_0 { |
| status = "okay"; |
| }; |
| |
| &remoteproc_adsp { |
| firmware-name = "qcom/sm8550/adsp.mbn", |
| "qcom/sm8550/adsp_dtb.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_cdsp { |
| firmware-name = "qcom/sm8550/cdsp.mbn", |
| "qcom/sm8550/cdsp_dtb.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_mpss { |
| firmware-name = "qcom/sm8550/modem.mbn", |
| "qcom/sm8550/modem_dtb.mbn"; |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_default &sdc2_card_det_n>; |
| pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>; |
| vmmc-supply = <&vreg_l9b_2p9>; |
| vqmmc-supply = <&vreg_l8b_1p8>; |
| bus-width = <4>; |
| no-sdio; |
| no-mmc; |
| status = "okay"; |
| }; |
| |
| &sleep_clk { |
| clock-frequency = <32000>; |
| }; |
| |
| &swr0 { |
| status = "okay"; |
| |
| /* WSA8845 */ |
| left_spkr: speaker@0,0 { |
| compatible = "sdw20217020400"; |
| reg = <0 0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spkr_1_sd_n_active>; |
| powerdown-gpios = <&lpass_tlmm 17 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "SpkrLeft"; |
| vdd-1p8-supply = <&vreg_l15b_1p8>; |
| vdd-io-supply = <&vreg_l3g_1p2>; |
| }; |
| |
| /* WSA8845 */ |
| right_spkr: speaker@0,1 { |
| compatible = "sdw20217020400"; |
| reg = <0 1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spkr_2_sd_n_active>; |
| powerdown-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "SpkrRight"; |
| vdd-1p8-supply = <&vreg_l15b_1p8>; |
| vdd-io-supply = <&vreg_l3g_1p2>; |
| }; |
| }; |
| |
| &swr1 { |
| status = "okay"; |
| |
| /* WCD9385 RX */ |
| wcd_rx: codec@0,4 { |
| compatible = "sdw20217010d00"; |
| reg = <0 4>; |
| qcom,rx-port-mapping = <1 2 3 4 5>; |
| }; |
| }; |
| |
| &swr2 { |
| status = "okay"; |
| |
| /* WCD9385 TX */ |
| wcd_tx: codec@0,3 { |
| compatible = "sdw20217010d00"; |
| reg = <0 3>; |
| qcom,tx-port-mapping = <2 2 3 4>; |
| }; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <32 8>; |
| |
| sde_dsi_active: sde-dsi-active-state { |
| pins = "gpio133"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| sde_dsi_suspend: sde-dsi-suspend-state { |
| pins = "gpio133"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| sde_te_active: sde-te-active-state { |
| pins = "gpio86"; |
| function = "mdp_vsync"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| sde_te_suspend: sde-te-suspend-state { |
| pins = "gpio86"; |
| function = "mdp_vsync"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| wcd_default: wcd-reset-n-active-state { |
| pins = "gpio108"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| }; |
| |
| &uart7 { |
| status = "okay"; |
| }; |
| |
| &ufs_mem_hc { |
| reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>; |
| vcc-supply = <&vreg_l17b_2p5>; |
| vcc-max-microamp = <1300000>; |
| vccq-supply = <&vreg_l1g_1p2>; |
| vccq-max-microamp = <1200000>; |
| vdd-hba-supply = <&vreg_l3g_1p2>; |
| |
| status = "okay"; |
| }; |
| |
| &ufs_mem_phy { |
| vdda-phy-supply = <&vreg_l1d_0p88>; |
| vdda-pll-supply = <&vreg_l3e_1p2>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_dwc3 { |
| dr_mode = "otg"; |
| usb-role-switch; |
| }; |
| |
| &usb_1_dwc3_hs { |
| remote-endpoint = <&pmic_glink_hs_in>; |
| }; |
| |
| &usb_1_dwc3_ss { |
| remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>; |
| }; |
| |
| &usb_1_hsphy { |
| vdd-supply = <&vreg_l1e_0p88>; |
| vdda12-supply = <&vreg_l3e_1p2>; |
| |
| phys = <&pm8550b_eusb2_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_dp_qmpphy { |
| vdda-phy-supply = <&vreg_l3e_1p2>; |
| vdda-pll-supply = <&vreg_l3f_0p91>; |
| |
| orientation-switch; |
| |
| status = "okay"; |
| }; |
| |
| &usb_dp_qmpphy_dp_in { |
| remote-endpoint = <&mdss_dp0_out>; |
| }; |
| |
| &usb_dp_qmpphy_out { |
| remote-endpoint = <&pmic_glink_ss_in>; |
| }; |
| |
| &usb_dp_qmpphy_usb_ss_in { |
| remote-endpoint = <&usb_1_dwc3_ss>; |
| }; |
| |
| &xo_board { |
| clock-frequency = <76800000>; |
| }; |
