| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Driver for the Renesas RZ/V2M I2C unit |
| * |
| * Copyright (C) 2016-2022 Renesas Electronics Corporation |
| */ |
| |
| #include <linux/bits.h> |
| #include <linux/clk.h> |
| #include <linux/device.h> |
| #include <linux/err.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/iopoll.h> |
| #include <linux/i2c.h> |
| #include <linux/jiffies.h> |
| #include <linux/kernel.h> |
| #include <linux/math64.h> |
| #include <linux/module.h> |
| #include <linux/mod_devicetable.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/reset.h> |
| |
| /* Register offsets */ |
| #define IICB0DAT 0x00 /* Data Register */ |
| #define IICB0CTL0 0x08 /* Control Register 0 */ |
| #define IICB0TRG 0x0C /* Trigger Register */ |
| #define IICB0STR0 0x10 /* Status Register 0 */ |
| #define IICB0CTL1 0x20 /* Control Register 1 */ |
| #define IICB0WL 0x24 /* Low Level Width Setting Reg */ |
| #define IICB0WH 0x28 /* How Level Width Setting Reg */ |
| |
| /* IICB0CTL0 */ |
| #define IICB0IICE BIT(7) /* I2C Enable */ |
| #define IICB0SLWT BIT(1) /* Interrupt Request Timing */ |
| #define IICB0SLAC BIT(0) /* Acknowledge */ |
| |
| /* IICB0TRG */ |
| #define IICB0WRET BIT(2) /* Quit Wait Trigger */ |
| #define IICB0STT BIT(1) /* Create Start Condition Trigger */ |
| #define IICB0SPT BIT(0) /* Create Stop Condition Trigger */ |
| |
| /* IICB0STR0 */ |
| #define IICB0SSAC BIT(8) /* Ack Flag */ |
| #define IICB0SSBS BIT(6) /* Bus Flag */ |
| #define IICB0SSSP BIT(4) /* Stop Condition Flag */ |
| |
| /* IICB0CTL1 */ |
| #define IICB0MDSC BIT(7) /* Bus Mode */ |
| #define IICB0SLSE BIT(1) /* Start condition output */ |
| |
| struct rzv2m_i2c_priv { |
| void __iomem *base; |
| struct i2c_adapter adap; |
| struct clk *clk; |
| int bus_mode; |
| struct completion msg_tia_done; |
| u32 iicb0wl; |
| u32 iicb0wh; |
| }; |
| |
| enum bcr_index { |
| RZV2M_I2C_100K = 0, |
| RZV2M_I2C_400K, |
| }; |
| |
| struct bitrate_config { |
| unsigned int percent_low; |
| unsigned int min_hold_time_ns; |
| }; |
| |
| static const struct bitrate_config bitrate_configs[] = { |
| [RZV2M_I2C_100K] = { 47, 3450 }, |
| [RZV2M_I2C_400K] = { 52, 900 }, |
| }; |
| |
| static inline void bit_setl(void __iomem *addr, u32 val) |
| { |
| writel(readl(addr) | val, addr); |
| } |
| |
| static inline void bit_clrl(void __iomem *addr, u32 val) |
| { |
| writel(readl(addr) & ~val, addr); |
| } |
| |
| static irqreturn_t rzv2m_i2c_tia_irq_handler(int this_irq, void *dev_id) |
| { |
| struct rzv2m_i2c_priv *priv = dev_id; |
| |
| complete(&priv->msg_tia_done); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /* Calculate IICB0WL and IICB0WH */ |
| static int rzv2m_i2c_clock_calculate(struct device *dev, |
| struct rzv2m_i2c_priv *priv) |
| { |
| const struct bitrate_config *config; |
| unsigned int hold_time_ns; |
| unsigned int total_pclks; |
| unsigned int trf_pclks; |
| unsigned long pclk_hz; |
| struct i2c_timings t; |
| u32 trf_ns; |
| |
| i2c_parse_fw_timings(dev, &t, true); |
| |
| pclk_hz = clk_get_rate(priv->clk); |
| total_pclks = pclk_hz / t.bus_freq_hz; |
| |
| trf_ns = t.scl_rise_ns + t.scl_fall_ns; |
| trf_pclks = mul_u64_u32_div(pclk_hz, trf_ns, NSEC_PER_SEC); |
| |
| /* Config setting */ |
| switch (t.bus_freq_hz) { |
| case I2C_MAX_FAST_MODE_FREQ: |
| priv->bus_mode = RZV2M_I2C_400K; |
| break; |
| case I2C_MAX_STANDARD_MODE_FREQ: |
| priv->bus_mode = RZV2M_I2C_100K; |
| break; |
| default: |
| dev_err(dev, "transfer speed is invalid\n"); |
| return -EINVAL; |
| } |
| config = &bitrate_configs[priv->bus_mode]; |
| |
| /* IICB0WL = (percent_low / Transfer clock) x PCLK */ |
| priv->iicb0wl = total_pclks * config->percent_low / 100; |
| if (priv->iicb0wl > (BIT(10) - 1)) |
| return -EINVAL; |
| |
| /* IICB0WH = ((percent_high / Transfer clock) x PCLK) - (tR + tF) */ |
| priv->iicb0wh = total_pclks - priv->iicb0wl - trf_pclks; |
| if (priv->iicb0wh > (BIT(10) - 1)) |
| return -EINVAL; |
| |
| /* |
| * Data hold time must be less than 0.9us in fast mode and |
| * 3.45us in standard mode. |
| * Data hold time = IICB0WL[9:2] / PCLK |
| */ |
| hold_time_ns = div64_ul((u64)(priv->iicb0wl >> 2) * NSEC_PER_SEC, pclk_hz); |
| if (hold_time_ns > config->min_hold_time_ns) { |
| dev_err(dev, "data hold time %dns is over %dns\n", |
| hold_time_ns, config->min_hold_time_ns); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static void rzv2m_i2c_init(struct rzv2m_i2c_priv *priv) |
| { |
| u32 i2c_ctl0; |
| u32 i2c_ctl1; |
| |
| /* i2c disable */ |
| writel(0, priv->base + IICB0CTL0); |
| |
| /* IICB0CTL1 setting */ |
| i2c_ctl1 = IICB0SLSE; |
| if (priv->bus_mode == RZV2M_I2C_400K) |
| i2c_ctl1 |= IICB0MDSC; |
| writel(i2c_ctl1, priv->base + IICB0CTL1); |
| |
| /* IICB0WL IICB0WH setting */ |
| writel(priv->iicb0wl, priv->base + IICB0WL); |
| writel(priv->iicb0wh, priv->base + IICB0WH); |
| |
| /* i2c enable after setting */ |
| i2c_ctl0 = IICB0SLWT | IICB0SLAC | IICB0IICE; |
| writel(i2c_ctl0, priv->base + IICB0CTL0); |
| } |
| |
| static int rzv2m_i2c_write_with_ack(struct rzv2m_i2c_priv *priv, u32 data) |
| { |
| unsigned long time_left; |
| |
| reinit_completion(&priv->msg_tia_done); |
| |
| writel(data, priv->base + IICB0DAT); |
| |
| time_left = wait_for_completion_timeout(&priv->msg_tia_done, |
| priv->adap.timeout); |
| if (!time_left) |
| return -ETIMEDOUT; |
| |
| /* Confirm ACK */ |
| if ((readl(priv->base + IICB0STR0) & IICB0SSAC) != IICB0SSAC) |
| return -ENXIO; |
| |
| return 0; |
| } |
| |
| static int rzv2m_i2c_read_with_ack(struct rzv2m_i2c_priv *priv, u8 *data, |
| bool last) |
| { |
| unsigned long time_left; |
| u32 data_tmp; |
| |
| reinit_completion(&priv->msg_tia_done); |
| |
| /* Interrupt request timing : 8th clock */ |
| bit_clrl(priv->base + IICB0CTL0, IICB0SLWT); |
| |
| /* Exit the wait state */ |
| writel(IICB0WRET, priv->base + IICB0TRG); |
| |
| /* Wait for transaction */ |
| time_left = wait_for_completion_timeout(&priv->msg_tia_done, |
| priv->adap.timeout); |
| if (!time_left) |
| return -ETIMEDOUT; |
| |
| if (last) { |
| /* Disable ACK */ |
| bit_clrl(priv->base + IICB0CTL0, IICB0SLAC); |
| |
| /* Read data*/ |
| data_tmp = readl(priv->base + IICB0DAT); |
| |
| /* Interrupt request timing : 9th clock */ |
| bit_setl(priv->base + IICB0CTL0, IICB0SLWT); |
| |
| /* Exit the wait state */ |
| writel(IICB0WRET, priv->base + IICB0TRG); |
| |
| /* Wait for transaction */ |
| time_left = wait_for_completion_timeout(&priv->msg_tia_done, |
| priv->adap.timeout); |
| if (!time_left) |
| return -ETIMEDOUT; |
| |
| /* Enable ACK */ |
| bit_setl(priv->base + IICB0CTL0, IICB0SLAC); |
| } else { |
| /* Read data */ |
| data_tmp = readl(priv->base + IICB0DAT); |
| } |
| |
| *data = data_tmp; |
| |
| return 0; |
| } |
| |
| static int rzv2m_i2c_send(struct rzv2m_i2c_priv *priv, struct i2c_msg *msg, |
| unsigned int *count) |
| { |
| unsigned int i; |
| int ret; |
| |
| for (i = 0; i < msg->len; i++) { |
| ret = rzv2m_i2c_write_with_ack(priv, msg->buf[i]); |
| if (ret < 0) |
| return ret; |
| } |
| *count = i; |
| |
| return 0; |
| } |
| |
| static int rzv2m_i2c_receive(struct rzv2m_i2c_priv *priv, struct i2c_msg *msg, |
| unsigned int *count) |
| { |
| unsigned int i; |
| int ret; |
| |
| for (i = 0; i < msg->len; i++) { |
| ret = rzv2m_i2c_read_with_ack(priv, &msg->buf[i], |
| (msg->len - 1) == i); |
| if (ret < 0) |
| return ret; |
| } |
| *count = i; |
| |
| return 0; |
| } |
| |
| static int rzv2m_i2c_send_address(struct rzv2m_i2c_priv *priv, |
| struct i2c_msg *msg) |
| { |
| u32 addr; |
| int ret; |
| |
| if (msg->flags & I2C_M_TEN) { |
| /* |
| * 10-bit address |
| * addr_1: 5'b11110 | addr[9:8] | (R/nW) |
| * addr_2: addr[7:0] |
| */ |
| addr = 0xf0 | ((msg->addr & GENMASK(9, 8)) >> 7); |
| addr |= !!(msg->flags & I2C_M_RD); |
| /* Send 1st address(extend code) */ |
| ret = rzv2m_i2c_write_with_ack(priv, addr); |
| if (ret) |
| return ret; |
| |
| /* Send 2nd address */ |
| ret = rzv2m_i2c_write_with_ack(priv, msg->addr & 0xff); |
| } else { |
| /* 7-bit address */ |
| addr = i2c_8bit_addr_from_msg(msg); |
| ret = rzv2m_i2c_write_with_ack(priv, addr); |
| } |
| |
| return ret; |
| } |
| |
| static int rzv2m_i2c_stop_condition(struct rzv2m_i2c_priv *priv) |
| { |
| u32 value; |
| |
| /* Send stop condition */ |
| writel(IICB0SPT, priv->base + IICB0TRG); |
| return readl_poll_timeout(priv->base + IICB0STR0, |
| value, value & IICB0SSSP, |
| 100, jiffies_to_usecs(priv->adap.timeout)); |
| } |
| |
| static int rzv2m_i2c_master_xfer_msg(struct rzv2m_i2c_priv *priv, |
| struct i2c_msg *msg, int stop) |
| { |
| unsigned int count = 0; |
| int ret, read = !!(msg->flags & I2C_M_RD); |
| |
| /* Send start condition */ |
| writel(IICB0STT, priv->base + IICB0TRG); |
| |
| ret = rzv2m_i2c_send_address(priv, msg); |
| if (!ret) { |
| if (read) |
| ret = rzv2m_i2c_receive(priv, msg, &count); |
| else |
| ret = rzv2m_i2c_send(priv, msg, &count); |
| |
| if (!ret && stop) |
| ret = rzv2m_i2c_stop_condition(priv); |
| } |
| |
| if (ret == -ENXIO) |
| rzv2m_i2c_stop_condition(priv); |
| else if (ret < 0) |
| rzv2m_i2c_init(priv); |
| else |
| ret = count; |
| |
| return ret; |
| } |
| |
| static int rzv2m_i2c_master_xfer(struct i2c_adapter *adap, |
| struct i2c_msg *msgs, int num) |
| { |
| struct rzv2m_i2c_priv *priv = i2c_get_adapdata(adap); |
| struct device *dev = priv->adap.dev.parent; |
| unsigned int i; |
| int ret; |
| |
| ret = pm_runtime_resume_and_get(dev); |
| if (ret < 0) |
| return ret; |
| |
| if (readl(priv->base + IICB0STR0) & IICB0SSBS) { |
| ret = -EAGAIN; |
| goto out; |
| } |
| |
| /* I2C main transfer */ |
| for (i = 0; i < num; i++) { |
| ret = rzv2m_i2c_master_xfer_msg(priv, &msgs[i], i == (num - 1)); |
| if (ret < 0) |
| goto out; |
| } |
| ret = num; |
| |
| out: |
| pm_runtime_mark_last_busy(dev); |
| pm_runtime_put_autosuspend(dev); |
| |
| return ret; |
| } |
| |
| static u32 rzv2m_i2c_func(struct i2c_adapter *adap) |
| { |
| return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) | |
| I2C_FUNC_10BIT_ADDR; |
| } |
| |
| static int rzv2m_i2c_disable(struct device *dev, struct rzv2m_i2c_priv *priv) |
| { |
| int ret; |
| |
| ret = pm_runtime_resume_and_get(dev); |
| if (ret < 0) |
| return ret; |
| |
| bit_clrl(priv->base + IICB0CTL0, IICB0IICE); |
| pm_runtime_put(dev); |
| |
| return 0; |
| } |
| |
| static const struct i2c_adapter_quirks rzv2m_i2c_quirks = { |
| .flags = I2C_AQ_NO_ZERO_LEN, |
| }; |
| |
| static struct i2c_algorithm rzv2m_i2c_algo = { |
| .master_xfer = rzv2m_i2c_master_xfer, |
| .functionality = rzv2m_i2c_func, |
| }; |
| |
| static int rzv2m_i2c_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct rzv2m_i2c_priv *priv; |
| struct reset_control *rstc; |
| struct i2c_adapter *adap; |
| struct resource *res; |
| int irq, ret; |
| |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res); |
| if (IS_ERR(priv->base)) |
| return PTR_ERR(priv->base); |
| |
| priv->clk = devm_clk_get(dev, NULL); |
| if (IS_ERR(priv->clk)) |
| return dev_err_probe(dev, PTR_ERR(priv->clk), "Can't get clock\n"); |
| |
| rstc = devm_reset_control_get_shared(dev, NULL); |
| if (IS_ERR(rstc)) |
| return dev_err_probe(dev, PTR_ERR(rstc), "Missing reset ctrl\n"); |
| /* |
| * The reset also affects other HW that is not under the control |
| * of Linux. Therefore, all we can do is deassert the reset. |
| */ |
| reset_control_deassert(rstc); |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) |
| return irq; |
| |
| ret = devm_request_irq(dev, irq, rzv2m_i2c_tia_irq_handler, 0, |
| dev_name(dev), priv); |
| if (ret < 0) |
| return dev_err_probe(dev, ret, "Unable to request irq %d\n", irq); |
| |
| adap = &priv->adap; |
| adap->nr = pdev->id; |
| adap->algo = &rzv2m_i2c_algo; |
| adap->quirks = &rzv2m_i2c_quirks; |
| adap->dev.parent = dev; |
| adap->owner = THIS_MODULE; |
| device_set_node(&adap->dev, dev_fwnode(dev)); |
| i2c_set_adapdata(adap, priv); |
| strscpy(adap->name, pdev->name, sizeof(adap->name)); |
| init_completion(&priv->msg_tia_done); |
| |
| ret = rzv2m_i2c_clock_calculate(dev, priv); |
| if (ret < 0) |
| return ret; |
| |
| pm_runtime_enable(dev); |
| |
| pm_runtime_get_sync(dev); |
| rzv2m_i2c_init(priv); |
| pm_runtime_put(dev); |
| |
| platform_set_drvdata(pdev, priv); |
| |
| ret = i2c_add_numbered_adapter(adap); |
| if (ret < 0) { |
| rzv2m_i2c_disable(dev, priv); |
| pm_runtime_disable(dev); |
| } |
| |
| return ret; |
| } |
| |
| static void rzv2m_i2c_remove(struct platform_device *pdev) |
| { |
| struct rzv2m_i2c_priv *priv = platform_get_drvdata(pdev); |
| struct device *dev = priv->adap.dev.parent; |
| |
| i2c_del_adapter(&priv->adap); |
| rzv2m_i2c_disable(dev, priv); |
| pm_runtime_disable(dev); |
| } |
| |
| static int rzv2m_i2c_suspend(struct device *dev) |
| { |
| struct rzv2m_i2c_priv *priv = dev_get_drvdata(dev); |
| |
| return rzv2m_i2c_disable(dev, priv); |
| } |
| |
| static int rzv2m_i2c_resume(struct device *dev) |
| { |
| struct rzv2m_i2c_priv *priv = dev_get_drvdata(dev); |
| int ret; |
| |
| ret = rzv2m_i2c_clock_calculate(dev, priv); |
| if (ret < 0) |
| return ret; |
| |
| ret = pm_runtime_resume_and_get(dev); |
| if (ret < 0) |
| return ret; |
| |
| rzv2m_i2c_init(priv); |
| pm_runtime_put(dev); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id rzv2m_i2c_ids[] = { |
| { .compatible = "renesas,rzv2m-i2c" }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, rzv2m_i2c_ids); |
| |
| static const struct dev_pm_ops rzv2m_i2c_pm_ops = { |
| SYSTEM_SLEEP_PM_OPS(rzv2m_i2c_suspend, rzv2m_i2c_resume) |
| }; |
| |
| static struct platform_driver rzv2m_i2c_driver = { |
| .driver = { |
| .name = "rzv2m-i2c", |
| .of_match_table = rzv2m_i2c_ids, |
| .pm = pm_sleep_ptr(&rzv2m_i2c_pm_ops), |
| }, |
| .probe = rzv2m_i2c_probe, |
| .remove_new = rzv2m_i2c_remove, |
| }; |
| module_platform_driver(rzv2m_i2c_driver); |
| |
| MODULE_DESCRIPTION("RZ/V2M I2C bus driver"); |
| MODULE_AUTHOR("Renesas Electronics Corporation"); |
| MODULE_LICENSE("GPL"); |