| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com> |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/i2c.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/module.h> |
| #include <linux/platform_device.h> |
| |
| #define UNIPHIER_I2C_DTRM 0x00 /* TX register */ |
| #define UNIPHIER_I2C_DTRM_IRQEN BIT(11) /* enable interrupt */ |
| #define UNIPHIER_I2C_DTRM_STA BIT(10) /* start condition */ |
| #define UNIPHIER_I2C_DTRM_STO BIT(9) /* stop condition */ |
| #define UNIPHIER_I2C_DTRM_NACK BIT(8) /* do not return ACK */ |
| #define UNIPHIER_I2C_DTRM_RD BIT(0) /* read transaction */ |
| #define UNIPHIER_I2C_DREC 0x04 /* RX register */ |
| #define UNIPHIER_I2C_DREC_MST BIT(14) /* 1 = master, 0 = slave */ |
| #define UNIPHIER_I2C_DREC_TX BIT(13) /* 1 = transmit, 0 = receive */ |
| #define UNIPHIER_I2C_DREC_STS BIT(12) /* stop condition detected */ |
| #define UNIPHIER_I2C_DREC_LRB BIT(11) /* no ACK */ |
| #define UNIPHIER_I2C_DREC_LAB BIT(9) /* arbitration lost */ |
| #define UNIPHIER_I2C_DREC_BBN BIT(8) /* bus not busy */ |
| #define UNIPHIER_I2C_MYAD 0x08 /* slave address */ |
| #define UNIPHIER_I2C_CLK 0x0c /* clock frequency control */ |
| #define UNIPHIER_I2C_BRST 0x10 /* bus reset */ |
| #define UNIPHIER_I2C_BRST_FOEN BIT(1) /* normal operation */ |
| #define UNIPHIER_I2C_BRST_RSCL BIT(0) /* release SCL */ |
| #define UNIPHIER_I2C_HOLD 0x14 /* hold time control */ |
| #define UNIPHIER_I2C_BSTS 0x18 /* bus status monitor */ |
| #define UNIPHIER_I2C_BSTS_SDA BIT(1) /* readback of SDA line */ |
| #define UNIPHIER_I2C_BSTS_SCL BIT(0) /* readback of SCL line */ |
| #define UNIPHIER_I2C_NOISE 0x1c /* noise filter control */ |
| #define UNIPHIER_I2C_SETUP 0x20 /* setup time control */ |
| |
| struct uniphier_i2c_priv { |
| struct completion comp; |
| struct i2c_adapter adap; |
| void __iomem *membase; |
| struct clk *clk; |
| unsigned int busy_cnt; |
| unsigned int clk_cycle; |
| }; |
| |
| static irqreturn_t uniphier_i2c_interrupt(int irq, void *dev_id) |
| { |
| struct uniphier_i2c_priv *priv = dev_id; |
| |
| /* |
| * This hardware uses edge triggered interrupt. Do not touch the |
| * hardware registers in this handler to make sure to catch the next |
| * interrupt edge. Just send a complete signal and return. |
| */ |
| complete(&priv->comp); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int uniphier_i2c_xfer_byte(struct i2c_adapter *adap, u32 txdata, |
| u32 *rxdatap) |
| { |
| struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap); |
| unsigned long time_left; |
| u32 rxdata; |
| |
| reinit_completion(&priv->comp); |
| |
| txdata |= UNIPHIER_I2C_DTRM_IRQEN; |
| writel(txdata, priv->membase + UNIPHIER_I2C_DTRM); |
| |
| time_left = wait_for_completion_timeout(&priv->comp, adap->timeout); |
| if (unlikely(!time_left)) { |
| dev_err(&adap->dev, "transaction timeout\n"); |
| return -ETIMEDOUT; |
| } |
| |
| rxdata = readl(priv->membase + UNIPHIER_I2C_DREC); |
| if (rxdatap) |
| *rxdatap = rxdata; |
| |
| return 0; |
| } |
| |
| static int uniphier_i2c_send_byte(struct i2c_adapter *adap, u32 txdata) |
| { |
| u32 rxdata; |
| int ret; |
| |
| ret = uniphier_i2c_xfer_byte(adap, txdata, &rxdata); |
| if (ret) |
| return ret; |
| |
| if (unlikely(rxdata & UNIPHIER_I2C_DREC_LAB)) |
| return -EAGAIN; |
| |
| if (unlikely(rxdata & UNIPHIER_I2C_DREC_LRB)) |
| return -ENXIO; |
| |
| return 0; |
| } |
| |
| static int uniphier_i2c_tx(struct i2c_adapter *adap, u16 addr, u16 len, |
| const u8 *buf) |
| { |
| int ret; |
| |
| ret = uniphier_i2c_send_byte(adap, addr << 1 | |
| UNIPHIER_I2C_DTRM_STA | |
| UNIPHIER_I2C_DTRM_NACK); |
| if (ret) |
| return ret; |
| |
| while (len--) { |
| ret = uniphier_i2c_send_byte(adap, |
| UNIPHIER_I2C_DTRM_NACK | *buf++); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int uniphier_i2c_rx(struct i2c_adapter *adap, u16 addr, u16 len, |
| u8 *buf) |
| { |
| int ret; |
| |
| ret = uniphier_i2c_send_byte(adap, addr << 1 | |
| UNIPHIER_I2C_DTRM_STA | |
| UNIPHIER_I2C_DTRM_NACK | |
| UNIPHIER_I2C_DTRM_RD); |
| if (ret) |
| return ret; |
| |
| while (len--) { |
| u32 rxdata; |
| |
| ret = uniphier_i2c_xfer_byte(adap, |
| len ? 0 : UNIPHIER_I2C_DTRM_NACK, |
| &rxdata); |
| if (ret) |
| return ret; |
| *buf++ = rxdata; |
| } |
| |
| return 0; |
| } |
| |
| static int uniphier_i2c_stop(struct i2c_adapter *adap) |
| { |
| return uniphier_i2c_send_byte(adap, UNIPHIER_I2C_DTRM_STO | |
| UNIPHIER_I2C_DTRM_NACK); |
| } |
| |
| static int uniphier_i2c_master_xfer_one(struct i2c_adapter *adap, |
| struct i2c_msg *msg, bool stop) |
| { |
| bool is_read = msg->flags & I2C_M_RD; |
| bool recovery = false; |
| int ret; |
| |
| if (is_read) |
| ret = uniphier_i2c_rx(adap, msg->addr, msg->len, msg->buf); |
| else |
| ret = uniphier_i2c_tx(adap, msg->addr, msg->len, msg->buf); |
| |
| if (ret == -EAGAIN) /* could not acquire bus. bail out without STOP */ |
| return ret; |
| |
| if (ret == -ETIMEDOUT) { |
| /* This error is fatal. Needs recovery. */ |
| stop = false; |
| recovery = true; |
| } |
| |
| if (stop) { |
| int ret2 = uniphier_i2c_stop(adap); |
| |
| if (ret2) { |
| /* Failed to issue STOP. The bus needs recovery. */ |
| recovery = true; |
| ret = ret ?: ret2; |
| } |
| } |
| |
| if (recovery) |
| i2c_recover_bus(adap); |
| |
| return ret; |
| } |
| |
| static int uniphier_i2c_check_bus_busy(struct i2c_adapter *adap) |
| { |
| struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap); |
| |
| if (!(readl(priv->membase + UNIPHIER_I2C_DREC) & |
| UNIPHIER_I2C_DREC_BBN)) { |
| if (priv->busy_cnt++ > 3) { |
| /* |
| * If bus busy continues too long, it is probably |
| * in a wrong state. Try bus recovery. |
| */ |
| i2c_recover_bus(adap); |
| priv->busy_cnt = 0; |
| } |
| |
| return -EAGAIN; |
| } |
| |
| priv->busy_cnt = 0; |
| return 0; |
| } |
| |
| static int uniphier_i2c_master_xfer(struct i2c_adapter *adap, |
| struct i2c_msg *msgs, int num) |
| { |
| struct i2c_msg *msg, *emsg = msgs + num; |
| int ret; |
| |
| ret = uniphier_i2c_check_bus_busy(adap); |
| if (ret) |
| return ret; |
| |
| for (msg = msgs; msg < emsg; msg++) { |
| /* Emit STOP if it is the last message or I2C_M_STOP is set. */ |
| bool stop = (msg + 1 == emsg) || (msg->flags & I2C_M_STOP); |
| |
| ret = uniphier_i2c_master_xfer_one(adap, msg, stop); |
| if (ret) |
| return ret; |
| } |
| |
| return num; |
| } |
| |
| static u32 uniphier_i2c_functionality(struct i2c_adapter *adap) |
| { |
| return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; |
| } |
| |
| static const struct i2c_algorithm uniphier_i2c_algo = { |
| .master_xfer = uniphier_i2c_master_xfer, |
| .functionality = uniphier_i2c_functionality, |
| }; |
| |
| static void uniphier_i2c_reset(struct uniphier_i2c_priv *priv, bool reset_on) |
| { |
| u32 val = UNIPHIER_I2C_BRST_RSCL; |
| |
| val |= reset_on ? 0 : UNIPHIER_I2C_BRST_FOEN; |
| writel(val, priv->membase + UNIPHIER_I2C_BRST); |
| } |
| |
| static int uniphier_i2c_get_scl(struct i2c_adapter *adap) |
| { |
| struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap); |
| |
| return !!(readl(priv->membase + UNIPHIER_I2C_BSTS) & |
| UNIPHIER_I2C_BSTS_SCL); |
| } |
| |
| static void uniphier_i2c_set_scl(struct i2c_adapter *adap, int val) |
| { |
| struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap); |
| |
| writel(val ? UNIPHIER_I2C_BRST_RSCL : 0, |
| priv->membase + UNIPHIER_I2C_BRST); |
| } |
| |
| static int uniphier_i2c_get_sda(struct i2c_adapter *adap) |
| { |
| struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap); |
| |
| return !!(readl(priv->membase + UNIPHIER_I2C_BSTS) & |
| UNIPHIER_I2C_BSTS_SDA); |
| } |
| |
| static void uniphier_i2c_unprepare_recovery(struct i2c_adapter *adap) |
| { |
| uniphier_i2c_reset(i2c_get_adapdata(adap), false); |
| } |
| |
| static struct i2c_bus_recovery_info uniphier_i2c_bus_recovery_info = { |
| .recover_bus = i2c_generic_scl_recovery, |
| .get_scl = uniphier_i2c_get_scl, |
| .set_scl = uniphier_i2c_set_scl, |
| .get_sda = uniphier_i2c_get_sda, |
| .unprepare_recovery = uniphier_i2c_unprepare_recovery, |
| }; |
| |
| static void uniphier_i2c_hw_init(struct uniphier_i2c_priv *priv) |
| { |
| unsigned int cyc = priv->clk_cycle; |
| |
| uniphier_i2c_reset(priv, true); |
| |
| /* |
| * Bit30-16: clock cycles of tLOW. |
| * Standard-mode: tLOW = 4.7 us, tHIGH = 4.0 us |
| * Fast-mode: tLOW = 1.3 us, tHIGH = 0.6 us |
| * "tLow/tHIGH = 5/4" meets both. |
| */ |
| writel((cyc * 5 / 9 << 16) | cyc, priv->membase + UNIPHIER_I2C_CLK); |
| |
| uniphier_i2c_reset(priv, false); |
| } |
| |
| static int uniphier_i2c_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct uniphier_i2c_priv *priv; |
| u32 bus_speed; |
| unsigned long clk_rate; |
| int irq, ret; |
| |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->membase = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(priv->membase)) |
| return PTR_ERR(priv->membase); |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) |
| return irq; |
| |
| if (of_property_read_u32(dev->of_node, "clock-frequency", &bus_speed)) |
| bus_speed = I2C_MAX_STANDARD_MODE_FREQ; |
| |
| if (!bus_speed || bus_speed > I2C_MAX_FAST_MODE_FREQ) { |
| dev_err(dev, "invalid clock-frequency %d\n", bus_speed); |
| return -EINVAL; |
| } |
| |
| priv->clk = devm_clk_get_enabled(dev, NULL); |
| if (IS_ERR(priv->clk)) { |
| dev_err(dev, "failed to enable clock\n"); |
| return PTR_ERR(priv->clk); |
| } |
| |
| clk_rate = clk_get_rate(priv->clk); |
| if (!clk_rate) { |
| dev_err(dev, "input clock rate should not be zero\n"); |
| return -EINVAL; |
| } |
| |
| priv->clk_cycle = clk_rate / bus_speed; |
| init_completion(&priv->comp); |
| priv->adap.owner = THIS_MODULE; |
| priv->adap.algo = &uniphier_i2c_algo; |
| priv->adap.dev.parent = dev; |
| priv->adap.dev.of_node = dev->of_node; |
| strscpy(priv->adap.name, "UniPhier I2C", sizeof(priv->adap.name)); |
| priv->adap.bus_recovery_info = &uniphier_i2c_bus_recovery_info; |
| i2c_set_adapdata(&priv->adap, priv); |
| platform_set_drvdata(pdev, priv); |
| |
| uniphier_i2c_hw_init(priv); |
| |
| ret = devm_request_irq(dev, irq, uniphier_i2c_interrupt, 0, pdev->name, |
| priv); |
| if (ret) { |
| dev_err(dev, "failed to request irq %d\n", irq); |
| return ret; |
| } |
| |
| return i2c_add_adapter(&priv->adap); |
| } |
| |
| static void uniphier_i2c_remove(struct platform_device *pdev) |
| { |
| struct uniphier_i2c_priv *priv = platform_get_drvdata(pdev); |
| |
| i2c_del_adapter(&priv->adap); |
| } |
| |
| static int __maybe_unused uniphier_i2c_suspend(struct device *dev) |
| { |
| struct uniphier_i2c_priv *priv = dev_get_drvdata(dev); |
| |
| clk_disable_unprepare(priv->clk); |
| |
| return 0; |
| } |
| |
| static int __maybe_unused uniphier_i2c_resume(struct device *dev) |
| { |
| struct uniphier_i2c_priv *priv = dev_get_drvdata(dev); |
| int ret; |
| |
| ret = clk_prepare_enable(priv->clk); |
| if (ret) |
| return ret; |
| |
| uniphier_i2c_hw_init(priv); |
| |
| return 0; |
| } |
| |
| static const struct dev_pm_ops uniphier_i2c_pm_ops = { |
| SET_SYSTEM_SLEEP_PM_OPS(uniphier_i2c_suspend, uniphier_i2c_resume) |
| }; |
| |
| static const struct of_device_id uniphier_i2c_match[] = { |
| { .compatible = "socionext,uniphier-i2c" }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(of, uniphier_i2c_match); |
| |
| static struct platform_driver uniphier_i2c_drv = { |
| .probe = uniphier_i2c_probe, |
| .remove_new = uniphier_i2c_remove, |
| .driver = { |
| .name = "uniphier-i2c", |
| .of_match_table = uniphier_i2c_match, |
| .pm = &uniphier_i2c_pm_ops, |
| }, |
| }; |
| module_platform_driver(uniphier_i2c_drv); |
| |
| MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>"); |
| MODULE_DESCRIPTION("UniPhier I2C bus driver"); |
| MODULE_LICENSE("GPL"); |