| The Linux SYM-2 driver documentation file |
| |
| Written by Gerard Roudier <groudier@free.fr> |
| 21 Rue Carnot |
| 95170 DEUIL LA BARRE - FRANCE |
| |
| Updated by Matthew Wilcox <matthew@wil.cx> |
| |
| 2004-10-09 |
| =============================================================================== |
| |
| 1. Introduction |
| 2. Supported chips and SCSI features |
| 3. Advantages of this driver for newer chips. |
| 3.1 Optimized SCSI SCRIPTS |
| 3.2 New features appeared with the SYM53C896 |
| 4. Memory mapped I/O versus normal I/O |
| 5. Tagged command queueing |
| 6. Parity checking |
| 7. Profiling information |
| 8. Control commands |
| 8.1 Set minimum synchronous period |
| 8.2 Set wide size |
| 8.3 Set maximum number of concurrent tagged commands |
| 8.4 Set debug mode |
| 8.5 Set flag (no_disc) |
| 8.6 Set verbose level |
| 8.7 Reset all logical units of a target |
| 8.8 Abort all tasks of all logical units of a target |
| 9. Configuration parameters |
| 10. Boot setup commands |
| 10.1 Syntax |
| 10.2 Available arguments |
| 10.2.1 Default number of tagged commands |
| 10.2.2 Burst max |
| 10.2.3 LED support |
| 10.2.4 Differential mode |
| 10.2.5 IRQ mode |
| 10.2.6 Check SCSI BUS |
| 10.2.7 Suggest a default SCSI id for hosts |
| 10.2.8 Verbosity level |
| 10.2.9 Debug mode |
| 10.2.10 Settle delay |
| 10.2.11 Serial NVRAM |
| 10.2.12 Exclude a host from being attached |
| 10.3 Converting from old options |
| 10.4 SCSI BUS checking boot option |
| 11. SCSI problem troubleshooting |
| 15.1 Problem tracking |
| 15.2 Understanding hardware error reports |
| 12. Serial NVRAM support (by Richard Waltham) |
| 17.1 Features |
| 17.2 Symbios NVRAM layout |
| 17.3 Tekram NVRAM layout |
| |
| =============================================================================== |
| |
| 1. Introduction |
| |
| This driver supports the whole SYM53C8XX family of PCI-SCSI controllers. |
| It also support the subset of LSI53C10XX PCI-SCSI controllers that are based |
| on the SYM53C8XX SCRIPTS language. |
| |
| It replaces the sym53c8xx+ncr53c8xx driver bundle and shares its core code |
| with the FreeBSD SYM-2 driver. The `glue' that allows this driver to work |
| under Linux is contained in 2 files named sym_glue.h and sym_glue.c. |
| Other drivers files are intended not to depend on the Operating System |
| on which the driver is used. |
| |
| The history of this driver can be summerized as follows: |
| |
| 1993: ncr driver written for 386bsd and FreeBSD by: |
| Wolfgang Stanglmeier <wolf@cologne.de> |
| Stefan Esser <se@mi.Uni-Koeln.de> |
| |
| 1996: port of the ncr driver to Linux-1.2.13 and rename it ncr53c8xx. |
| Gerard Roudier |
| |
| 1998: new sym53c8xx driver for Linux based on LOAD/STORE instruction and that |
| adds full support for the 896 but drops support for early NCR devices. |
| Gerard Roudier |
| |
| 1999: port of the sym53c8xx driver to FreeBSD and support for the LSI53C1010 |
| 33 MHz and 66MHz Ultra-3 controllers. The new driver is named `sym'. |
| Gerard Roudier |
| |
| 2000: Add support for early NCR devices to FreeBSD `sym' driver. |
| Break the driver into several sources and separate the OS glue |
| code from the core code that can be shared among different O/Ses. |
| Write a glue code for Linux. |
| Gerard Roudier |
| |
| 2004: Remove FreeBSD compatibility code. Remove support for versions of |
| Linux before 2.6. Start using Linux facilities. |
| |
| This README file addresses the Linux version of the driver. Under FreeBSD, |
| the driver documentation is the sym.8 man page. |
| |
| Information about new chips is available at LSILOGIC web server: |
| |
| http://www.lsilogic.com/ |
| |
| SCSI standard documentations are available at T10 site: |
| |
| http://www.t10.org/ |
| |
| Useful SCSI tools written by Eric Youngdale are part of most Linux |
| distributions: |
| scsiinfo: command line tool |
| scsi-config: TCL/Tk tool using scsiinfo |
| |
| 2. Supported chips and SCSI features |
| |
| The following features are supported for all chips: |
| |
| Synchronous negotiation |
| Disconnection |
| Tagged command queuing |
| SCSI parity checking |
| PCI Master parity checking |
| |
| Other features depends on chip capabilities. |
| The driver notably uses optimized SCRIPTS for devices that support |
| LOAD/STORE and handles PHASE MISMATCH from SCRIPTS for devices that |
| support the corresponding feature. |
| |
| The following table shows some characteristics of the chip family. |
| |
| On board LOAD/STORE HARDWARE |
| Chip SDMS BIOS Wide SCSI std. Max. sync SCRIPTS PHASE MISMATCH |
| ---- --------- ---- --------- ---------- ---------- -------------- |
| 810 N N FAST10 10 MB/s N N |
| 810A N N FAST10 10 MB/s Y N |
| 815 Y N FAST10 10 MB/s N N |
| 825 Y Y FAST10 20 MB/s N N |
| 825A Y Y FAST10 20 MB/s Y N |
| 860 N N FAST20 20 MB/s Y N |
| 875 Y Y FAST20 40 MB/s Y N |
| 875A Y Y FAST20 40 MB/s Y Y |
| 876 Y Y FAST20 40 MB/s Y N |
| 895 Y Y FAST40 80 MB/s Y N |
| 895A Y Y FAST40 80 MB/s Y Y |
| 896 Y Y FAST40 80 MB/s Y Y |
| 897 Y Y FAST40 80 MB/s Y Y |
| 1510D Y Y FAST40 80 MB/s Y Y |
| 1010 Y Y FAST80 160 MB/s Y Y |
| 1010_66* Y Y FAST80 160 MB/s Y Y |
| |
| * Chip supports 33MHz and 66MHz PCI bus clock. |
| |
| |
| Summary of other supported features: |
| |
| Module: allow to load the driver |
| Memory mapped I/O: increases performance |
| Control commands: write operations to the proc SCSI file system |
| Debugging information: written to syslog (expert only) |
| Scatter / gather |
| Shared interrupt |
| Boot setup commands |
| Serial NVRAM: Symbios and Tekram formats |
| |
| |
| 3. Advantages of this driver for newer chips. |
| |
| 3.1 Optimized SCSI SCRIPTS. |
| |
| All chips except the 810, 815 and 825, support new SCSI SCRIPTS instructions |
| named LOAD and STORE that allow to move up to 1 DWORD from/to an IO register |
| to/from memory much faster that the MOVE MEMORY instruction that is supported |
| by the 53c7xx and 53c8xx family. |
| |
| The LOAD/STORE instructions support absolute and DSA relative addressing |
| modes. The SCSI SCRIPTS had been entirely rewritten using LOAD/STORE instead |
| of MOVE MEMORY instructions. |
| |
| Due to the lack of LOAD/STORE SCRIPTS instructions by earlier chips, this |
| driver also incorporates a different SCRIPTS set based on MEMORY MOVE, in |
| order to provide support for the entire SYM53C8XX chips family. |
| |
| 3.2 New features appeared with the SYM53C896 |
| |
| Newer chips (see above) allows handling of the phase mismatch context from |
| SCRIPTS (avoids the phase mismatch interrupt that stops the SCSI processor |
| until the C code has saved the context of the transfer). |
| |
| The 896 and 1010 chips support 64 bit PCI transactions and addressing, |
| while the 895A supports 32 bit PCI transactions and 64 bit addressing. |
| The SCRIPTS processor of these chips is not true 64 bit, but uses segment |
| registers for bit 32-63. Another interesting feature is that LOAD/STORE |
| instructions that address the on-chip RAM (8k) remain internal to the chip. |
| |
| 4. Memory mapped I/O versus normal I/O |
| |
| Memory mapped I/O has less latency than normal I/O and is the recommended |
| way for doing IO with PCI devices. Memory mapped I/O seems to work fine on |
| most hardware configurations, but some poorly designed chipsets may break |
| this feature. A configuration option is provided for normal I/O to be |
| used but the driver defaults to MMIO. |
| |
| 5. Tagged command queueing |
| |
| Queuing more than 1 command at a time to a device allows it to perform |
| optimizations based on actual head positions and its mechanical |
| characteristics. This feature may also reduce average command latency. |
| In order to really gain advantage of this feature, devices must have |
| a reasonable cache size (No miracle is to be expected for a low-end |
| hard disk with 128 KB or less). |
| Some kown old SCSI devices do not properly support tagged command queuing. |
| Generally, firmware revisions that fix this kind of problems are available |
| at respective vendor web/ftp sites. |
| All I can say is that I never have had problem with tagged queuing using |
| this driver and its predecessors. Hard disks that behaved correctly for |
| me using tagged commands are the following: |
| |
| - IBM S12 0662 |
| - Conner 1080S |
| - Quantum Atlas I |
| - Quantum Atlas II |
| - Seagate Cheetah I |
| - Quantum Viking II |
| - IBM DRVS |
| - Quantum Atlas IV |
| - Seagate Cheetah II |
| |
| If your controller has NVRAM, you can configure this feature per target |
| from the user setup tool. The Tekram Setup program allows to tune the |
| maximum number of queued commands up to 32. The Symbios Setup only allows |
| to enable or disable this feature. |
| |
| The maximum number of simultaneous tagged commands queued to a device |
| is currently set to 16 by default. This value is suitable for most SCSI |
| disks. With large SCSI disks (>= 2GB, cache >= 512KB, average seek time |
| <= 10 ms), using a larger value may give better performances. |
| |
| This driver supports up to 255 commands per device, and but using more than |
| 64 is generally not worth-while, unless you are using a very large disk or |
| disk arrays. It is noticeable that most of recent hard disks seem not to |
| accept more than 64 simultaneous commands. So, using more than 64 queued |
| commands is probably just resource wasting. |
| |
| If your controller does not have NVRAM or if it is managed by the SDMS |
| BIOS/SETUP, you can configure tagged queueing feature and device queue |
| depths from the boot command-line. For example: |
| |
| sym53c8xx=tags:4/t2t3q15-t4q7/t1u0q32 |
| |
| will set tagged commands queue depths as follow: |
| |
| - target 2 all luns on controller 0 --> 15 |
| - target 3 all luns on controller 0 --> 15 |
| - target 4 all luns on controller 0 --> 7 |
| - target 1 lun 0 on controller 1 --> 32 |
| - all other target/lun --> 4 |
| |
| In some special conditions, some SCSI disk firmwares may return a |
| QUEUE FULL status for a SCSI command. This behaviour is managed by the |
| driver using the following heuristic: |
| |
| - Each time a QUEUE FULL status is returned, tagged queue depth is reduced |
| to the actual number of disconnected commands. |
| |
| - Every 200 successfully completed SCSI commands, if allowed by the |
| current limit, the maximum number of queueable commands is incremented. |
| |
| Since QUEUE FULL status reception and handling is resource wasting, the |
| driver notifies by default this problem to user by indicating the actual |
| number of commands used and their status, as well as its decision on the |
| device queue depth change. |
| The heuristic used by the driver in handling QUEUE FULL ensures that the |
| impact on performances is not too bad. You can get rid of the messages by |
| setting verbose level to zero, as follow: |
| |
| 1st method: boot your system using 'sym53c8xx=verb:0' option. |
| 2nd method: apply "setverbose 0" control command to the proc fs entry |
| corresponding to your controller after boot-up. |
| |
| 6. Parity checking |
| |
| The driver supports SCSI parity checking and PCI bus master parity |
| checking. These features must be enabled in order to ensure safe |
| data transfers. Some flawed devices or mother boards may have problems |
| with parity. The options to defeat parity checking have been removed |
| from the driver. |
| |
| 7. Profiling information |
| |
| This driver does not provide profiling informations as did its predecessors. |
| This feature was not this useful and added complexity to the code. |
| As the driver code got more complex, I have decided to remove everything |
| that didn't seem actually useful. |
| |
| 8. Control commands |
| |
| Control commands can be sent to the driver with write operations to |
| the proc SCSI file system. The generic command syntax is the |
| following: |
| |
| echo "<verb> <parameters>" >/proc/scsi/sym53c8xx/0 |
| (assumes controller number is 0) |
| |
| Using "all" for "<target>" parameter with the commands below will |
| apply to all targets of the SCSI chain (except the controller). |
| |
| Available commands: |
| |
| 8.1 Set minimum synchronous period factor |
| |
| setsync <target> <period factor> |
| |
| target: target number |
| period: minimum synchronous period. |
| Maximum speed = 1000/(4*period factor) except for special |
| cases below. |
| |
| Specify a period of 0, to force asynchronous transfer mode. |
| |
| 9 means 12.5 nano-seconds synchronous period |
| 10 means 25 nano-seconds synchronous period |
| 11 means 30 nano-seconds synchronous period |
| 12 means 50 nano-seconds synchronous period |
| |
| 8.2 Set wide size |
| |
| setwide <target> <size> |
| |
| target: target number |
| size: 0=8 bits, 1=16bits |
| |
| 8.3 Set maximum number of concurrent tagged commands |
| |
| settags <target> <tags> |
| |
| target: target number |
| tags: number of concurrent tagged commands |
| must not be greater than configured (default: 16) |
| |
| 8.4 Set debug mode |
| |
| setdebug <list of debug flags> |
| |
| Available debug flags: |
| alloc: print info about memory allocations (ccb, lcb) |
| queue: print info about insertions into the command start queue |
| result: print sense data on CHECK CONDITION status |
| scatter: print info about the scatter process |
| scripts: print info about the script binding process |
| tiny: print minimal debugging information |
| timing: print timing information of the NCR chip |
| nego: print information about SCSI negotiations |
| phase: print information on script interruptions |
| |
| Use "setdebug" with no argument to reset debug flags. |
| |
| |
| 8.5 Set flag (no_disc) |
| |
| setflag <target> <flag> |
| |
| target: target number |
| |
| For the moment, only one flag is available: |
| |
| no_disc: not allow target to disconnect. |
| |
| Do not specify any flag in order to reset the flag. For example: |
| - setflag 4 |
| will reset no_disc flag for target 4, so will allow it disconnections. |
| - setflag all |
| will allow disconnection for all devices on the SCSI bus. |
| |
| |
| 8.6 Set verbose level |
| |
| setverbose #level |
| |
| The driver default verbose level is 1. This command allows to change |
| th driver verbose level after boot-up. |
| |
| 8.7 Reset all logical units of a target |
| |
| resetdev <target> |
| |
| target: target number |
| The driver will try to send a BUS DEVICE RESET message to the target. |
| |
| 8.8 Abort all tasks of all logical units of a target |
| |
| cleardev <target> |
| |
| target: target number |
| The driver will try to send a ABORT message to all the logical units |
| of the target. |
| |
| |
| 9. Configuration parameters |
| |
| Under kernel configuration tools (make menuconfig, for example), it is |
| possible to change some default driver configuration parameters. |
| If the firmware of all your devices is perfect enough, all the |
| features supported by the driver can be enabled at start-up. However, |
| if only one has a flaw for some SCSI feature, you can disable the |
| support by the driver of this feature at linux start-up and enable |
| this feature after boot-up only for devices that support it safely. |
| |
| Configuration parameters: |
| |
| Use normal IO (default answer: n) |
| Answer "y" if you suspect your mother board to not allow memory mapped I/O. |
| May slow down performance a little. |
| |
| Default tagged command queue depth (default answer: 16) |
| Entering 0 defaults to tagged commands not being used. |
| This parameter can be specified from the boot command line. |
| |
| Maximum number of queued commands (default answer: 32) |
| This option allows you to specify the maximum number of tagged commands |
| that can be queued to a device. The maximum supported value is 255. |
| |
| Synchronous transfers frequency (default answer: 80) |
| This option allows you to specify the frequency in MHz the driver |
| will use at boot time for synchronous data transfer negotiations. |
| 0 means "asynchronous data transfers". |
| |
| 10. Boot setup commands |
| |
| 10.1 Syntax |
| |
| Setup commands can be passed to the driver either at boot time or as |
| parameters to modprobe, as described in Documentation/kernel-parameters.txt |
| |
| Example of boot setup command under lilo prompt: |
| |
| lilo: linux root=/dev/sda2 sym53c8xx.cmd_per_lun=4 sym53c8xx.sync=10 sym53c8xx.debug=0x200 |
| |
| - enable tagged commands, up to 4 tagged commands queued. |
| - set synchronous negotiation speed to 10 Mega-transfers / second. |
| - set DEBUG_NEGO flag. |
| |
| The following command will install the driver module with the same |
| options as above. |
| |
| modprobe sym53c8xx cmd_per_lun=4 sync=10 debug=0x200 |
| |
| 10.2 Available arguments |
| |
| 10.2.1 Default number of tagged commands |
| cmd_per_lun=0 (or cmd_per_lun=1) tagged command queuing disabled |
| cmd_per_lun=#tags (#tags > 1) tagged command queuing enabled |
| #tags will be truncated to the max queued commands configuration parameter. |
| |
| 10.2.2 Detailed control of tagged commands |
| This option allows you to specify a command queue depth for each device |
| that supports tagged command queueing. |
| Example: |
| tag_ctrl=10/t2t3q16-t5q24/t1u2q32 |
| will set devices queue depth as follow: |
| - controller #0 target #2 and target #3 -> 16 commands, |
| - controller #0 target #5 -> 24 commands, |
| - controller #1 target #1 logical unit #2 -> 32 commands, |
| - all other logical units (all targets, all controllers) -> 10 commands. |
| |
| 10.2.3 Burst max |
| burst=0 burst disabled |
| burst=255 get burst length from initial IO register settings. |
| burst=#x burst enabled (1<<#x burst transfers max) |
| #x is an integer value which is log base 2 of the burst transfers max. |
| By default the driver uses the maximum value supported by the chip. |
| |
| 10.2.4 LED support |
| led=1 enable LED support |
| led=0 disable LED support |
| Do not enable LED support if your scsi board does not use SDMS BIOS. |
| (See 'Configuration parameters') |
| |
| 10.2.4 Differential mode |
| diff=0 never set up diff mode |
| diff=1 set up diff mode if BIOS set it |
| diff=2 always set up diff mode |
| diff=3 set diff mode if GPIO3 is not set |
| |
| 10.2.5 IRQ mode |
| irqm=0 always open drain |
| irqm=1 same as initial settings (assumed BIOS settings) |
| irqm=2 always totem pole |
| |
| 10.2.6 Check SCSI BUS |
| buschk=<option bits> |
| |
| Available option bits: |
| 0x0: No check. |
| 0x1: Check and do not attach the controller on error. |
| 0x2: Check and just warn on error. |
| |
| 10.2.7 Suggest a default SCSI id for hosts |
| hostid=255 no id suggested. |
| hostid=#x (0 < x < 7) x suggested for hosts SCSI id. |
| |
| If a host SCSI id is available from the NVRAM, the driver will ignore |
| any value suggested as boot option. Otherwise, if a suggested value |
| different from 255 has been supplied, it will use it. Otherwise, it will |
| try to deduce the value previously set in the hardware and use value |
| 7 if the hardware value is zero. |
| |
| 10.2.8 Verbosity level |
| verb=0 minimal |
| verb=1 normal |
| verb=2 too much |
| |
| 10.2.9 Debug mode |
| debug=0 clear debug flags |
| debug=#x set debug flags |
| #x is an integer value combining the following power-of-2 values: |
| DEBUG_ALLOC 0x1 |
| DEBUG_PHASE 0x2 |
| DEBUG_POLL 0x4 |
| DEBUG_QUEUE 0x8 |
| DEBUG_RESULT 0x10 |
| DEBUG_SCATTER 0x20 |
| DEBUG_SCRIPT 0x40 |
| DEBUG_TINY 0x80 |
| DEBUG_TIMING 0x100 |
| DEBUG_NEGO 0x200 |
| DEBUG_TAGS 0x400 |
| DEBUG_FREEZE 0x800 |
| DEBUG_RESTART 0x1000 |
| |
| You can play safely with DEBUG_NEGO. However, some of these flags may |
| generate bunches of syslog messages. |
| |
| 10.2.10 Settle delay |
| settle=n delay for n seconds |
| |
| After a bus reset, the driver will delay for n seconds before talking |
| to any device on the bus. The default is 3 seconds and safe mode will |
| default it to 10. |
| |
| 10.2.11 Serial NVRAM |
| NB: option not currently implemented. |
| nvram=n do not look for serial NVRAM |
| nvram=y test controllers for onboard serial NVRAM |
| (alternate binary form) |
| nvram=<bits options> |
| 0x01 look for NVRAM (equivalent to nvram=y) |
| 0x02 ignore NVRAM "Synchronous negotiation" parameters for all devices |
| 0x04 ignore NVRAM "Wide negotiation" parameter for all devices |
| 0x08 ignore NVRAM "Scan at boot time" parameter for all devices |
| 0x80 also attach controllers set to OFF in the NVRAM (sym53c8xx only) |
| |
| 10.2.12 Exclude a host from being attached |
| excl=<io_address>,... |
| |
| Prevent host at a given io address from being attached. |
| For example 'excl=0xb400,0xc000' indicate to the |
| driver not to attach hosts at address 0xb400 and 0xc000. |
| |
| 10.3 Converting from old style options |
| |
| Previously, the sym2 driver accepted arguments of the form |
| sym53c8xx=tags:4,sync:10,debug:0x200 |
| |
| As a result of the new module parameters, this is no longer available. |
| Most of the options have remained the same, but tags has split into |
| cmd_per_lun and tag_ctrl for its two different purposes. The sample above |
| would be specified as: |
| modprobe sym53c8xx cmd_per_lun=4 sync=10 debug=0x200 |
| |
| or on the kernel boot line as: |
| sym53c8xx.cmd_per_lun=4 sym53c8xx.sync=10 sym53c8xx.debug=0x200 |
| |
| 10.4 SCSI BUS checking boot option. |
| |
| When this option is set to a non-zero value, the driver checks SCSI lines |
| logic state, 100 micro-seconds after having asserted the SCSI RESET line. |
| The driver just reads SCSI lines and checks all lines read FALSE except RESET. |
| Since SCSI devices shall release the BUS at most 800 nano-seconds after SCSI |
| RESET has been asserted, any signal to TRUE may indicate a SCSI BUS problem. |
| Unfortunately, the following common SCSI BUS problems are not detected: |
| - Only 1 terminator installed. |
| - Misplaced terminators. |
| - Bad quality terminators. |
| On the other hand, either bad cabling, broken devices, not conformant |
| devices, ... may cause a SCSI signal to be wrong when te driver reads it. |
| |
| 15. SCSI problem troubleshooting |
| |
| 15.1 Problem tracking |
| |
| Most SCSI problems are due to a non conformant SCSI bus or too buggy |
| devices. If infortunately you have SCSI problems, you can check the |
| following things: |
| |
| - SCSI bus cables |
| - terminations at both end of the SCSI chain |
| - linux syslog messages (some of them may help you) |
| |
| If you do not find the source of problems, you can configure the |
| driver or devices in the NVRAM with minimal features. |
| |
| - only asynchronous data transfers |
| - tagged commands disabled |
| - disconnections not allowed |
| |
| Now, if your SCSI bus is ok, your system has every chance to work |
| with this safe configuration but performances will not be optimal. |
| |
| If it still fails, then you can send your problem description to |
| appropriate mailing lists or news-groups. Send me a copy in order to |
| be sure I will receive it. Obviously, a bug in the driver code is |
| possible. |
| |
| My cyrrent email address: Gerard Roudier <groudier@free.fr> |
| |
| Allowing disconnections is important if you use several devices on |
| your SCSI bus but often causes problems with buggy devices. |
| Synchronous data transfers increases throughput of fast devices like |
| hard disks. Good SCSI hard disks with a large cache gain advantage of |
| tagged commands queuing. |
| |
| 15.2 Understanding hardware error reports |
| |
| When the driver detects an unexpected error condition, it may display a |
| message of the following pattern. |
| |
| sym0:1: ERROR (0:48) (1-21-65) (f/95/0) @ (script 7c0:19000000). |
| sym0: script cmd = 19000000 |
| sym0: regdump: da 10 80 95 47 0f 01 07 75 01 81 21 80 01 09 00. |
| |
| Some fields in such a message may help you understand the cause of the |
| problem, as follows: |
| |
| sym0:1: ERROR (0:48) (1-21-65) (f/95/0) @ (script 7c0:19000000). |
| .....A.........B.C....D.E..F....G.H..I.......J.....K...L....... |
| |
| Field A : target number. |
| SCSI ID of the device the controller was talking with at the moment the |
| error occurs. |
| |
| Field B : DSTAT io register (DMA STATUS) |
| Bit 0x40 : MDPE Master Data Parity Error |
| Data parity error detected on the PCI BUS. |
| Bit 0x20 : BF Bus Fault |
| PCI bus fault condition detected |
| Bit 0x01 : IID Illegal Instruction Detected |
| Set by the chip when it detects an Illegal Instruction format |
| on some condition that makes an instruction illegal. |
| Bit 0x80 : DFE Dma Fifo Empty |
| Pure status bit that does not indicate an error. |
| If the reported DSTAT value contains a combination of MDPE (0x40), |
| BF (0x20), then the cause may be likely due to a PCI BUS problem. |
| |
| Field C : SIST io register (SCSI Interrupt Status) |
| Bit 0x08 : SGE SCSI GROSS ERROR |
| Indicates that the chip detected a severe error condition |
| on the SCSI BUS that prevents the SCSI protocol from functioning |
| properly. |
| Bit 0x04 : UDC Unexpected Disconnection |
| Indicates that the device released the SCSI BUS when the chip |
| was not expecting this to happen. A device may behave so to |
| indicate the SCSI initiator that an error condition not reportable using the SCSI protocol has occurred. |
| Bit 0x02 : RST SCSI BUS Reset |
| Generally SCSI targets do not reset the SCSI BUS, although any |
| device on the BUS can reset it at any time. |
| Bit 0x01 : PAR Parity |
| SCSI parity error detected. |
| On a faulty SCSI BUS, any error condition among SGE (0x08), UDC (0x04) and |
| PAR (0x01) may be detected by the chip. If your SCSI system sometimes |
| encounters such error conditions, especially SCSI GROSS ERROR, then a SCSI |
| BUS problem is likely the cause of these errors. |
| |
| For fields D,E,F,G and H, you may look into the sym53c8xx_defs.h file |
| that contains some minimal comments on IO register bits. |
| Field D : SOCL Scsi Output Control Latch |
| This register reflects the state of the SCSI control lines the |
| chip want to drive or compare against. |
| Field E : SBCL Scsi Bus Control Lines |
| Actual value of control lines on the SCSI BUS. |
| Field F : SBDL Scsi Bus Data Lines |
| Actual value of data lines on the SCSI BUS. |
| Field G : SXFER SCSI Transfer |
| Contains the setting of the Synchronous Period for output and |
| the current Synchronous offset (offset 0 means asynchronous). |
| Field H : SCNTL3 Scsi Control Register 3 |
| Contains the setting of timing values for both asynchronous and |
| synchronous data transfers. |
| Field I : SCNTL4 Scsi Control Register 4 |
| Only meaninful for 53C1010 Ultra3 controllers. |
| |
| Understanding Fields J, K, L and dumps requires to have good knowledge of |
| SCSI standards, chip cores functionnals and internal driver data structures. |
| You are not required to decode and understand them, unless you want to help |
| maintain the driver code. |
| |
| 17. Serial NVRAM (added by Richard Waltham: dormouse@farsrobt.demon.co.uk) |
| |
| 17.1 Features |
| |
| Enabling serial NVRAM support enables detection of the serial NVRAM included |
| on Symbios and some Symbios compatible host adaptors, and Tekram boards. The |
| serial NVRAM is used by Symbios and Tekram to hold set up parameters for the |
| host adaptor and it's attached drives. |
| |
| The Symbios NVRAM also holds data on the boot order of host adaptors in a |
| system with more than one host adaptor. This information is no longer used |
| as it's fundamentally incompatible with the hotplug PCI model. |
| |
| Tekram boards using Symbios chips, DC390W/F/U, which have NVRAM are detected |
| and this is used to distinguish between Symbios compatible and Tekram host |
| adaptors. This is used to disable the Symbios compatible "diff" setting |
| incorrectly set on Tekram boards if the CONFIG_SCSI_53C8XX_SYMBIOS_COMPAT |
| configuration parameter is set enabling both Symbios and Tekram boards to be |
| used together with the Symbios cards using all their features, including |
| "diff" support. ("led pin" support for Symbios compatible cards can remain |
| enabled when using Tekram cards. It does nothing useful for Tekram host |
| adaptors but does not cause problems either.) |
| |
| The parameters the driver is able to get from the NVRAM depend on the |
| data format used, as follow: |
| |
| Tekram format Symbios format |
| General and host parameters |
| Boot order N Y |
| Host SCSI ID Y Y |
| SCSI parity checking Y Y |
| Verbose boot messages N Y |
| SCSI devices parameters |
| Synchronous transfer speed Y Y |
| Wide 16 / Narrow Y Y |
| Tagged Command Queuing enabled Y Y |
| Disconnections enabled Y Y |
| Scan at boot time N Y |
| |
| In order to speed up the system boot, for each device configured without |
| the "scan at boot time" option, the driver forces an error on the |
| first TEST UNIT READY command received for this device. |
| |
| |
| 17.2 Symbios NVRAM layout |
| |
| typical data at NVRAM address 0x100 (53c810a NVRAM) |
| ----------------------------------------------------------- |
| 00 00 |
| 64 01 |
| 8e 0b |
| |
| 00 30 00 00 00 00 07 00 00 00 00 00 00 00 07 04 10 04 00 00 |
| |
| 04 00 0f 00 00 10 00 50 00 00 01 00 00 62 |
| 04 00 03 00 00 10 00 58 00 00 01 00 00 63 |
| 04 00 01 00 00 10 00 48 00 00 01 00 00 61 |
| 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 |
| |
| fe fe |
| 00 00 |
| 00 00 |
| ----------------------------------------------------------- |
| NVRAM layout details |
| |
| NVRAM Address 0x000-0x0ff not used |
| 0x100-0x26f initialised data |
| 0x270-0x7ff not used |
| |
| general layout |
| |
| header - 6 bytes, |
| data - 356 bytes (checksum is byte sum of this data) |
| trailer - 6 bytes |
| --- |
| total 368 bytes |
| |
| data area layout |
| |
| controller set up - 20 bytes |
| boot configuration - 56 bytes (4x14 bytes) |
| device set up - 128 bytes (16x8 bytes) |
| unused (spare?) - 152 bytes (19x8 bytes) |
| --- |
| total 356 bytes |
| |
| ----------------------------------------------------------- |
| header |
| |
| 00 00 - ?? start marker |
| 64 01 - byte count (lsb/msb excludes header/trailer) |
| 8e 0b - checksum (lsb/msb excludes header/trailer) |
| ----------------------------------------------------------- |
| controller set up |
| |
| 00 30 00 00 00 00 07 00 00 00 00 00 00 00 07 04 10 04 00 00 |
| | | | | |
| | | | -- host ID |
| | | | |
| | | --Removable Media Support |
| | | 0x00 = none |
| | | 0x01 = Bootable Device |
| | | 0x02 = All with Media |
| | | |
| | --flag bits 2 |
| | 0x00000001= scan order hi->low |
| | (default 0x00 - scan low->hi) |
| --flag bits 1 |
| 0x00000001 scam enable |
| 0x00000010 parity enable |
| 0x00000100 verbose boot msgs |
| |
| remaining bytes unknown - they do not appear to change in my |
| current set up for any of the controllers. |
| |
| default set up is identical for 53c810a and 53c875 NVRAM |
| (Removable Media added Symbios BIOS version 4.09) |
| ----------------------------------------------------------- |
| boot configuration |
| |
| boot order set by order of the devices in this table |
| |
| 04 00 0f 00 00 10 00 50 00 00 01 00 00 62 -- 1st controller |
| 04 00 03 00 00 10 00 58 00 00 01 00 00 63 2nd controller |
| 04 00 01 00 00 10 00 48 00 00 01 00 00 61 3rd controller |
| 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4th controller |
| | | | | | | | | |
| | | | | | | ---- PCI io port adr |
| | | | | | --0x01 init/scan at boot time |
| | | | | --PCI device/function number (0xdddddfff) |
| | | ----- ?? PCI vendor ID (lsb/msb) |
| ----PCI device ID (lsb/msb) |
| |
| ?? use of this data is a guess but seems reasonable |
| |
| remaining bytes unknown - they do not appear to change in my |
| current set up |
| |
| default set up is identical for 53c810a and 53c875 NVRAM |
| ----------------------------------------------------------- |
| device set up (up to 16 devices - includes controller) |
| |
| 0f 00 08 08 64 00 0a 00 - id 0 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 |
| 0f 00 08 08 64 00 0a 00 - id 15 |
| | | | | | | |
| | | | | ----timeout (lsb/msb) |
| | | | --synch period (0x?? 40 Mtrans/sec- fast 40) (probably 0x28) |
| | | | (0x30 20 Mtrans/sec- fast 20) |
| | | | (0x64 10 Mtrans/sec- fast ) |
| | | | (0xc8 5 Mtrans/sec) |
| | | | (0x00 asynchronous) |
| | | -- ?? max sync offset (0x08 in NVRAM on 53c810a) |
| | | (0x10 in NVRAM on 53c875) |
| | --device bus width (0x08 narrow) |
| | (0x10 16 bit wide) |
| --flag bits |
| 0x00000001 - disconnect enabled |
| 0x00000010 - scan at boot time |
| 0x00000100 - scan luns |
| 0x00001000 - queue tags enabled |
| |
| remaining bytes unknown - they do not appear to change in my |
| current set up |
| |
| ?? use of this data is a guess but seems reasonable |
| (but it could be max bus width) |
| |
| default set up for 53c810a NVRAM |
| default set up for 53c875 NVRAM - bus width - 0x10 |
| - sync offset ? - 0x10 |
| - sync period - 0x30 |
| ----------------------------------------------------------- |
| ?? spare device space (32 bit bus ??) |
| |
| 00 00 00 00 00 00 00 00 (19x8bytes) |
| . |
| . |
| 00 00 00 00 00 00 00 00 |
| |
| default set up is identical for 53c810a and 53c875 NVRAM |
| ----------------------------------------------------------- |
| trailer |
| |
| fe fe - ? end marker ? |
| 00 00 |
| 00 00 |
| |
| default set up is identical for 53c810a and 53c875 NVRAM |
| ----------------------------------------------------------- |
| |
| |
| |
| 17.3 Tekram NVRAM layout |
| |
| nvram 64x16 (1024 bit) |
| |
| Drive settings |
| |
| Drive ID 0-15 (addr 0x0yyyy0 = device setup, yyyy = ID) |
| (addr 0x0yyyy1 = 0x0000) |
| |
| x x x x x x x x x x x x x x x x |
| | | | | | | | | | |
| | | | | | | | | ----- parity check 0 - off |
| | | | | | | | | 1 - on |
| | | | | | | | | |
| | | | | | | | ------- sync neg 0 - off |
| | | | | | | | 1 - on |
| | | | | | | | |
| | | | | | | --------- disconnect 0 - off |
| | | | | | | 1 - on |
| | | | | | | |
| | | | | | ----------- start cmd 0 - off |
| | | | | | 1 - on |
| | | | | | |
| | | | | -------------- tagged cmds 0 - off |
| | | | | 1 - on |
| | | | | |
| | | | ---------------- wide neg 0 - off |
| | | | 1 - on |
| | | | |
| --------------------------- sync rate 0 - 10.0 Mtrans/sec |
| 1 - 8.0 |
| 2 - 6.6 |
| 3 - 5.7 |
| 4 - 5.0 |
| 5 - 4.0 |
| 6 - 3.0 |
| 7 - 2.0 |
| 7 - 2.0 |
| 8 - 20.0 |
| 9 - 16.7 |
| a - 13.9 |
| b - 11.9 |
| |
| Global settings |
| |
| Host flags 0 (addr 0x100000, 32) |
| |
| x x x x x x x x x x x x x x x x |
| | | | | | | | | | | | | |
| | | | | | | | | ----------- host ID 0x00 - 0x0f |
| | | | | | | | | |
| | | | | | | | ----------------------- support for 0 - off |
| | | | | | | | > 2 drives 1 - on |
| | | | | | | | |
| | | | | | | ------------------------- support drives 0 - off |
| | | | | | | > 1Gbytes 1 - on |
| | | | | | | |
| | | | | | --------------------------- bus reset on 0 - off |
| | | | | | power on 1 - on |
| | | | | | |
| | | | | ----------------------------- active neg 0 - off |
| | | | | 1 - on |
| | | | | |
| | | | -------------------------------- imm seek 0 - off |
| | | | 1 - on |
| | | | |
| | | ---------------------------------- scan luns 0 - off |
| | | 1 - on |
| | | |
| -------------------------------------- removable 0 - disable |
| as BIOS dev 1 - boot device |
| 2 - all |
| |
| Host flags 1 (addr 0x100001, 33) |
| |
| x x x x x x x x x x x x x x x x |
| | | | | | | |
| | | | --------- boot delay 0 - 3 sec |
| | | | 1 - 5 |
| | | | 2 - 10 |
| | | | 3 - 20 |
| | | | 4 - 30 |
| | | | 5 - 60 |
| | | | 6 - 120 |
| | | | |
| --------------------------- max tag cmds 0 - 2 |
| 1 - 4 |
| 2 - 8 |
| 3 - 16 |
| 4 - 32 |
| |
| Host flags 2 (addr 0x100010, 34) |
| |
| x x x x x x x x x x x x x x x x |
| | |
| ----- F2/F6 enable 0 - off ??? |
| 1 - on ??? |
| |
| checksum (addr 0x111111) |
| |
| checksum = 0x1234 - (sum addr 0-63) |
| |
| ---------------------------------------------------------------------------- |
| |
| default nvram data: |
| |
| 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 |
| 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 |
| 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 |
| 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 |
| |
| 0x0f07 0x0400 0x0001 0x0000 0x0000 0x0000 0x0000 0x0000 |
| 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 |
| 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 |
| 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0xfbbc |
| |
| |
| =============================================================================== |
| End of Linux SYM-2 driver documentation file |
