blob: 1b247722ba25dccc5d056c677600da75e73f9a1d [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-only
/*
* Xilinx XADC driver
*
* Copyright 2013-2014 Analog Devices Inc.
* Author: Lars-Peter Clausen <lars@metafoo.de>
*
* Documentation for the parts can be found at:
* - XADC hardmacro: Xilinx UG480
* - ZYNQ XADC interface: Xilinx UG585
* - AXI XADC interface: Xilinx PG019
*/
#include <linux/clk.h>
#include <linux/device.h>
#include <linux/err.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/mod_devicetable.h>
#include <linux/module.h>
#include <linux/overflow.h>
#include <linux/platform_device.h>
#include <linux/property.h>
#include <linux/slab.h>
#include <linux/sysfs.h>
#include <linux/iio/buffer.h>
#include <linux/iio/events.h>
#include <linux/iio/iio.h>
#include <linux/iio/sysfs.h>
#include <linux/iio/trigger.h>
#include <linux/iio/trigger_consumer.h>
#include <linux/iio/triggered_buffer.h>
#include "xilinx-xadc.h"
static const unsigned int XADC_ZYNQ_UNMASK_TIMEOUT = 500;
/* ZYNQ register definitions */
#define XADC_ZYNQ_REG_CFG 0x00
#define XADC_ZYNQ_REG_INTSTS 0x04
#define XADC_ZYNQ_REG_INTMSK 0x08
#define XADC_ZYNQ_REG_STATUS 0x0c
#define XADC_ZYNQ_REG_CFIFO 0x10
#define XADC_ZYNQ_REG_DFIFO 0x14
#define XADC_ZYNQ_REG_CTL 0x18
#define XADC_ZYNQ_CFG_ENABLE BIT(31)
#define XADC_ZYNQ_CFG_CFIFOTH_MASK (0xf << 20)
#define XADC_ZYNQ_CFG_CFIFOTH_OFFSET 20
#define XADC_ZYNQ_CFG_DFIFOTH_MASK (0xf << 16)
#define XADC_ZYNQ_CFG_DFIFOTH_OFFSET 16
#define XADC_ZYNQ_CFG_WEDGE BIT(13)
#define XADC_ZYNQ_CFG_REDGE BIT(12)
#define XADC_ZYNQ_CFG_TCKRATE_MASK (0x3 << 8)
#define XADC_ZYNQ_CFG_TCKRATE_DIV2 (0x0 << 8)
#define XADC_ZYNQ_CFG_TCKRATE_DIV4 (0x1 << 8)
#define XADC_ZYNQ_CFG_TCKRATE_DIV8 (0x2 << 8)
#define XADC_ZYNQ_CFG_TCKRATE_DIV16 (0x3 << 8)
#define XADC_ZYNQ_CFG_IGAP_MASK 0x1f
#define XADC_ZYNQ_CFG_IGAP(x) (x)
#define XADC_ZYNQ_INT_CFIFO_LTH BIT(9)
#define XADC_ZYNQ_INT_DFIFO_GTH BIT(8)
#define XADC_ZYNQ_INT_ALARM_MASK 0xff
#define XADC_ZYNQ_INT_ALARM_OFFSET 0
#define XADC_ZYNQ_STATUS_CFIFO_LVL_MASK (0xf << 16)
#define XADC_ZYNQ_STATUS_CFIFO_LVL_OFFSET 16
#define XADC_ZYNQ_STATUS_DFIFO_LVL_MASK (0xf << 12)
#define XADC_ZYNQ_STATUS_DFIFO_LVL_OFFSET 12
#define XADC_ZYNQ_STATUS_CFIFOF BIT(11)
#define XADC_ZYNQ_STATUS_CFIFOE BIT(10)
#define XADC_ZYNQ_STATUS_DFIFOF BIT(9)
#define XADC_ZYNQ_STATUS_DFIFOE BIT(8)
#define XADC_ZYNQ_STATUS_OT BIT(7)
#define XADC_ZYNQ_STATUS_ALM(x) BIT(x)
#define XADC_ZYNQ_CTL_RESET BIT(4)
#define XADC_ZYNQ_CMD_NOP 0x00
#define XADC_ZYNQ_CMD_READ 0x01
#define XADC_ZYNQ_CMD_WRITE 0x02
#define XADC_ZYNQ_CMD(cmd, addr, data) (((cmd) << 26) | ((addr) << 16) | (data))
/* AXI register definitions */
#define XADC_AXI_REG_RESET 0x00
#define XADC_AXI_REG_STATUS 0x04
#define XADC_AXI_REG_ALARM_STATUS 0x08
#define XADC_AXI_REG_CONVST 0x0c
#define XADC_AXI_REG_XADC_RESET 0x10
#define XADC_AXI_REG_GIER 0x5c
#define XADC_AXI_REG_IPISR 0x60
#define XADC_AXI_REG_IPIER 0x68
/* 7 Series */
#define XADC_7S_AXI_ADC_REG_OFFSET 0x200
/* UltraScale */
#define XADC_US_AXI_ADC_REG_OFFSET 0x400
#define XADC_AXI_RESET_MAGIC 0xa
#define XADC_AXI_GIER_ENABLE BIT(31)
#define XADC_AXI_INT_EOS BIT(4)
#define XADC_AXI_INT_ALARM_MASK 0x3c0f
#define XADC_FLAGS_BUFFERED BIT(0)
#define XADC_FLAGS_IRQ_OPTIONAL BIT(1)
/*
* The XADC hardware supports a samplerate of up to 1MSPS. Unfortunately it does
* not have a hardware FIFO. Which means an interrupt is generated for each
* conversion sequence. At 1MSPS sample rate the CPU in ZYNQ7000 is completely
* overloaded by the interrupts that it soft-lockups. For this reason the driver
* limits the maximum samplerate 150kSPS. At this rate the CPU is fairly busy,
* but still responsive.
*/
#define XADC_MAX_SAMPLERATE 150000
static void xadc_write_reg(struct xadc *xadc, unsigned int reg,
uint32_t val)
{
writel(val, xadc->base + reg);
}
static void xadc_read_reg(struct xadc *xadc, unsigned int reg,
uint32_t *val)
{
*val = readl(xadc->base + reg);
}
/*
* The ZYNQ interface uses two asynchronous FIFOs for communication with the
* XADC. Reads and writes to the XADC register are performed by submitting a
* request to the command FIFO (CFIFO), once the request has been completed the
* result can be read from the data FIFO (DFIFO). The method currently used in
* this driver is to submit the request for a read/write operation, then go to
* sleep and wait for an interrupt that signals that a response is available in
* the data FIFO.
*/
static void xadc_zynq_write_fifo(struct xadc *xadc, uint32_t *cmd,
unsigned int n)
{
unsigned int i;
for (i = 0; i < n; i++)
xadc_write_reg(xadc, XADC_ZYNQ_REG_CFIFO, cmd[i]);
}
static void xadc_zynq_drain_fifo(struct xadc *xadc)
{
uint32_t status, tmp;
xadc_read_reg(xadc, XADC_ZYNQ_REG_STATUS, &status);
while (!(status & XADC_ZYNQ_STATUS_DFIFOE)) {
xadc_read_reg(xadc, XADC_ZYNQ_REG_DFIFO, &tmp);
xadc_read_reg(xadc, XADC_ZYNQ_REG_STATUS, &status);
}
}
static void xadc_zynq_update_intmsk(struct xadc *xadc, unsigned int mask,
unsigned int val)
{
xadc->zynq_intmask &= ~mask;
xadc->zynq_intmask |= val;
xadc_write_reg(xadc, XADC_ZYNQ_REG_INTMSK,
xadc->zynq_intmask | xadc->zynq_masked_alarm);
}
static int xadc_zynq_write_adc_reg(struct xadc *xadc, unsigned int reg,
uint16_t val)
{
uint32_t cmd[1];
uint32_t tmp;
int ret;
spin_lock_irq(&xadc->lock);
xadc_zynq_update_intmsk(xadc, XADC_ZYNQ_INT_DFIFO_GTH,
XADC_ZYNQ_INT_DFIFO_GTH);
reinit_completion(&xadc->completion);
cmd[0] = XADC_ZYNQ_CMD(XADC_ZYNQ_CMD_WRITE, reg, val);
xadc_zynq_write_fifo(xadc, cmd, ARRAY_SIZE(cmd));
xadc_read_reg(xadc, XADC_ZYNQ_REG_CFG, &tmp);
tmp &= ~XADC_ZYNQ_CFG_DFIFOTH_MASK;
tmp |= 0 << XADC_ZYNQ_CFG_DFIFOTH_OFFSET;
xadc_write_reg(xadc, XADC_ZYNQ_REG_CFG, tmp);
xadc_zynq_update_intmsk(xadc, XADC_ZYNQ_INT_DFIFO_GTH, 0);
spin_unlock_irq(&xadc->lock);
ret = wait_for_completion_interruptible_timeout(&xadc->completion, HZ);
if (ret == 0)
ret = -EIO;
else
ret = 0;
xadc_read_reg(xadc, XADC_ZYNQ_REG_DFIFO, &tmp);
return ret;
}
static int xadc_zynq_read_adc_reg(struct xadc *xadc, unsigned int reg,
uint16_t *val)
{
uint32_t cmd[2];
uint32_t resp, tmp;
int ret;
cmd[0] = XADC_ZYNQ_CMD(XADC_ZYNQ_CMD_READ, reg, 0);
cmd[1] = XADC_ZYNQ_CMD(XADC_ZYNQ_CMD_NOP, 0, 0);
spin_lock_irq(&xadc->lock);
xadc_zynq_update_intmsk(xadc, XADC_ZYNQ_INT_DFIFO_GTH,
XADC_ZYNQ_INT_DFIFO_GTH);
xadc_zynq_drain_fifo(xadc);
reinit_completion(&xadc->completion);
xadc_zynq_write_fifo(xadc, cmd, ARRAY_SIZE(cmd));
xadc_read_reg(xadc, XADC_ZYNQ_REG_CFG, &tmp);
tmp &= ~XADC_ZYNQ_CFG_DFIFOTH_MASK;
tmp |= 1 << XADC_ZYNQ_CFG_DFIFOTH_OFFSET;
xadc_write_reg(xadc, XADC_ZYNQ_REG_CFG, tmp);
xadc_zynq_update_intmsk(xadc, XADC_ZYNQ_INT_DFIFO_GTH, 0);
spin_unlock_irq(&xadc->lock);
ret = wait_for_completion_interruptible_timeout(&xadc->completion, HZ);
if (ret == 0)
ret = -EIO;
if (ret < 0)
return ret;
xadc_read_reg(xadc, XADC_ZYNQ_REG_DFIFO, &resp);
xadc_read_reg(xadc, XADC_ZYNQ_REG_DFIFO, &resp);
*val = resp & 0xffff;
return 0;
}
static unsigned int xadc_zynq_transform_alarm(unsigned int alarm)
{
return ((alarm & 0x80) >> 4) |
((alarm & 0x78) << 1) |
(alarm & 0x07);
}
/*
* The ZYNQ threshold interrupts are level sensitive. Since we can't make the
* threshold condition go way from within the interrupt handler, this means as
* soon as a threshold condition is present we would enter the interrupt handler
* again and again. To work around this we mask all active thresholds interrupts
* in the interrupt handler and start a timer. In this timer we poll the
* interrupt status and only if the interrupt is inactive we unmask it again.
*/
static void xadc_zynq_unmask_worker(struct work_struct *work)
{
struct xadc *xadc = container_of(work, struct xadc, zynq_unmask_work.work);
unsigned int misc_sts, unmask;
xadc_read_reg(xadc, XADC_ZYNQ_REG_STATUS, &misc_sts);
misc_sts &= XADC_ZYNQ_INT_ALARM_MASK;
spin_lock_irq(&xadc->lock);
/* Clear those bits which are not active anymore */
unmask = (xadc->zynq_masked_alarm ^ misc_sts) & xadc->zynq_masked_alarm;
xadc->zynq_masked_alarm &= misc_sts;
/* Also clear those which are masked out anyway */
xadc->zynq_masked_alarm &= ~xadc->zynq_intmask;
/* Clear the interrupts before we unmask them */
xadc_write_reg(xadc, XADC_ZYNQ_REG_INTSTS, unmask);
xadc_zynq_update_intmsk(xadc, 0, 0);
spin_unlock_irq(&xadc->lock);
/* if still pending some alarm re-trigger the timer */
if (xadc->zynq_masked_alarm) {
schedule_delayed_work(&xadc->zynq_unmask_work,
msecs_to_jiffies(XADC_ZYNQ_UNMASK_TIMEOUT));
}
}
static irqreturn_t xadc_zynq_interrupt_handler(int irq, void *devid)
{
struct iio_dev *indio_dev = devid;
struct xadc *xadc = iio_priv(indio_dev);
uint32_t status;
xadc_read_reg(xadc, XADC_ZYNQ_REG_INTSTS, &status);
status &= ~(xadc->zynq_intmask | xadc->zynq_masked_alarm);
if (!status)
return IRQ_NONE;
spin_lock(&xadc->lock);
xadc_write_reg(xadc, XADC_ZYNQ_REG_INTSTS, status);
if (status & XADC_ZYNQ_INT_DFIFO_GTH) {
xadc_zynq_update_intmsk(xadc, XADC_ZYNQ_INT_DFIFO_GTH,
XADC_ZYNQ_INT_DFIFO_GTH);
complete(&xadc->completion);
}
status &= XADC_ZYNQ_INT_ALARM_MASK;
if (status) {
xadc->zynq_masked_alarm |= status;
/*
* mask the current event interrupt,
* unmask it when the interrupt is no more active.
*/
xadc_zynq_update_intmsk(xadc, 0, 0);
xadc_handle_events(indio_dev,
xadc_zynq_transform_alarm(status));
/* unmask the required interrupts in timer. */
schedule_delayed_work(&xadc->zynq_unmask_work,
msecs_to_jiffies(XADC_ZYNQ_UNMASK_TIMEOUT));
}
spin_unlock(&xadc->lock);
return IRQ_HANDLED;
}
#define XADC_ZYNQ_TCK_RATE_MAX 50000000
#define XADC_ZYNQ_IGAP_DEFAULT 20
#define XADC_ZYNQ_PCAP_RATE_MAX 200000000
static int xadc_zynq_setup(struct platform_device *pdev,
struct iio_dev *indio_dev, int irq)
{
struct xadc *xadc = iio_priv(indio_dev);
unsigned long pcap_rate;
unsigned int tck_div;
unsigned int div;
unsigned int igap;
unsigned int tck_rate;
int ret;
/* TODO: Figure out how to make igap and tck_rate configurable */
igap = XADC_ZYNQ_IGAP_DEFAULT;
tck_rate = XADC_ZYNQ_TCK_RATE_MAX;
xadc->zynq_intmask = ~0;
pcap_rate = clk_get_rate(xadc->clk);
if (!pcap_rate)
return -EINVAL;
if (pcap_rate > XADC_ZYNQ_PCAP_RATE_MAX) {
ret = clk_set_rate(xadc->clk,
(unsigned long)XADC_ZYNQ_PCAP_RATE_MAX);
if (ret)
return ret;
}
if (tck_rate > pcap_rate / 2) {
div = 2;
} else {
div = pcap_rate / tck_rate;
if (pcap_rate / div > XADC_ZYNQ_TCK_RATE_MAX)
div++;
}
if (div <= 3)
tck_div = XADC_ZYNQ_CFG_TCKRATE_DIV2;
else if (div <= 7)
tck_div = XADC_ZYNQ_CFG_TCKRATE_DIV4;
else if (div <= 15)
tck_div = XADC_ZYNQ_CFG_TCKRATE_DIV8;
else
tck_div = XADC_ZYNQ_CFG_TCKRATE_DIV16;
xadc_write_reg(xadc, XADC_ZYNQ_REG_CTL, XADC_ZYNQ_CTL_RESET);
xadc_write_reg(xadc, XADC_ZYNQ_REG_CTL, 0);
xadc_write_reg(xadc, XADC_ZYNQ_REG_INTSTS, ~0);
xadc_write_reg(xadc, XADC_ZYNQ_REG_INTMSK, xadc->zynq_intmask);
xadc_write_reg(xadc, XADC_ZYNQ_REG_CFG, XADC_ZYNQ_CFG_ENABLE |
XADC_ZYNQ_CFG_REDGE | XADC_ZYNQ_CFG_WEDGE |
tck_div | XADC_ZYNQ_CFG_IGAP(igap));
if (pcap_rate > XADC_ZYNQ_PCAP_RATE_MAX) {
ret = clk_set_rate(xadc->clk, pcap_rate);
if (ret)
return ret;
}
return 0;
}
static unsigned long xadc_zynq_get_dclk_rate(struct xadc *xadc)
{
unsigned int div;
uint32_t val;
xadc_read_reg(xadc, XADC_ZYNQ_REG_CFG, &val);
switch (val & XADC_ZYNQ_CFG_TCKRATE_MASK) {
case XADC_ZYNQ_CFG_TCKRATE_DIV4:
div = 4;
break;
case XADC_ZYNQ_CFG_TCKRATE_DIV8:
div = 8;
break;
case XADC_ZYNQ_CFG_TCKRATE_DIV16:
div = 16;
break;
default:
div = 2;
break;
}
return clk_get_rate(xadc->clk) / div;
}
static void xadc_zynq_update_alarm(struct xadc *xadc, unsigned int alarm)
{
unsigned long flags;
uint32_t status;
/* Move OT to bit 7 */
alarm = ((alarm & 0x08) << 4) | ((alarm & 0xf0) >> 1) | (alarm & 0x07);
spin_lock_irqsave(&xadc->lock, flags);
/* Clear previous interrupts if any. */
xadc_read_reg(xadc, XADC_ZYNQ_REG_INTSTS, &status);
xadc_write_reg(xadc, XADC_ZYNQ_REG_INTSTS, status & alarm);
xadc_zynq_update_intmsk(xadc, XADC_ZYNQ_INT_ALARM_MASK,
~alarm & XADC_ZYNQ_INT_ALARM_MASK);
spin_unlock_irqrestore(&xadc->lock, flags);
}
static const struct xadc_ops xadc_zynq_ops = {
.read = xadc_zynq_read_adc_reg,
.write = xadc_zynq_write_adc_reg,
.setup = xadc_zynq_setup,
.get_dclk_rate = xadc_zynq_get_dclk_rate,
.interrupt_handler = xadc_zynq_interrupt_handler,
.update_alarm = xadc_zynq_update_alarm,
.type = XADC_TYPE_S7,
};
static const unsigned int xadc_axi_reg_offsets[] = {
[XADC_TYPE_S7] = XADC_7S_AXI_ADC_REG_OFFSET,
[XADC_TYPE_US] = XADC_US_AXI_ADC_REG_OFFSET,
};
static int xadc_axi_read_adc_reg(struct xadc *xadc, unsigned int reg,
uint16_t *val)
{
uint32_t val32;
xadc_read_reg(xadc, xadc_axi_reg_offsets[xadc->ops->type] + reg * 4,
&val32);
*val = val32 & 0xffff;
return 0;
}
static int xadc_axi_write_adc_reg(struct xadc *xadc, unsigned int reg,
uint16_t val)
{
xadc_write_reg(xadc, xadc_axi_reg_offsets[xadc->ops->type] + reg * 4,
val);
return 0;
}
static int xadc_axi_setup(struct platform_device *pdev,
struct iio_dev *indio_dev, int irq)
{
struct xadc *xadc = iio_priv(indio_dev);
xadc_write_reg(xadc, XADC_AXI_REG_RESET, XADC_AXI_RESET_MAGIC);
xadc_write_reg(xadc, XADC_AXI_REG_GIER, XADC_AXI_GIER_ENABLE);
return 0;
}
static irqreturn_t xadc_axi_interrupt_handler(int irq, void *devid)
{
struct iio_dev *indio_dev = devid;
struct xadc *xadc = iio_priv(indio_dev);
uint32_t status, mask;
unsigned int events;
xadc_read_reg(xadc, XADC_AXI_REG_IPISR, &status);
xadc_read_reg(xadc, XADC_AXI_REG_IPIER, &mask);
status &= mask;
if (!status)
return IRQ_NONE;
if ((status & XADC_AXI_INT_EOS) && xadc->trigger)
iio_trigger_poll(xadc->trigger);
if (status & XADC_AXI_INT_ALARM_MASK) {
/*
* The order of the bits in the AXI-XADC status register does
* not match the order of the bits in the XADC alarm enable
* register. xadc_handle_events() expects the events to be in
* the same order as the XADC alarm enable register.
*/
events = (status & 0x000e) >> 1;
events |= (status & 0x0001) << 3;
events |= (status & 0x3c00) >> 6;
xadc_handle_events(indio_dev, events);
}
xadc_write_reg(xadc, XADC_AXI_REG_IPISR, status);
return IRQ_HANDLED;
}
static void xadc_axi_update_alarm(struct xadc *xadc, unsigned int alarm)
{
uint32_t val;
unsigned long flags;
/*
* The order of the bits in the AXI-XADC status register does not match
* the order of the bits in the XADC alarm enable register. We get
* passed the alarm mask in the same order as in the XADC alarm enable
* register.
*/
alarm = ((alarm & 0x07) << 1) | ((alarm & 0x08) >> 3) |
((alarm & 0xf0) << 6);
spin_lock_irqsave(&xadc->lock, flags);
xadc_read_reg(xadc, XADC_AXI_REG_IPIER, &val);
val &= ~XADC_AXI_INT_ALARM_MASK;
val |= alarm;
xadc_write_reg(xadc, XADC_AXI_REG_IPIER, val);
spin_unlock_irqrestore(&xadc->lock, flags);
}
static unsigned long xadc_axi_get_dclk(struct xadc *xadc)
{
return clk_get_rate(xadc->clk);
}
static const struct xadc_ops xadc_7s_axi_ops = {
.read = xadc_axi_read_adc_reg,
.write = xadc_axi_write_adc_reg,
.setup = xadc_axi_setup,
.get_dclk_rate = xadc_axi_get_dclk,
.update_alarm = xadc_axi_update_alarm,
.interrupt_handler = xadc_axi_interrupt_handler,
.flags = XADC_FLAGS_BUFFERED | XADC_FLAGS_IRQ_OPTIONAL,
.type = XADC_TYPE_S7,
};
static const struct xadc_ops xadc_us_axi_ops = {
.read = xadc_axi_read_adc_reg,
.write = xadc_axi_write_adc_reg,
.setup = xadc_axi_setup,
.get_dclk_rate = xadc_axi_get_dclk,
.update_alarm = xadc_axi_update_alarm,
.interrupt_handler = xadc_axi_interrupt_handler,
.flags = XADC_FLAGS_BUFFERED | XADC_FLAGS_IRQ_OPTIONAL,
.type = XADC_TYPE_US,
};
static int _xadc_update_adc_reg(struct xadc *xadc, unsigned int reg,
uint16_t mask, uint16_t val)
{
uint16_t tmp;
int ret;
ret = _xadc_read_adc_reg(xadc, reg, &tmp);
if (ret)
return ret;
return _xadc_write_adc_reg(xadc, reg, (tmp & ~mask) | val);
}
static int xadc_update_adc_reg(struct xadc *xadc, unsigned int reg,
uint16_t mask, uint16_t val)
{
int ret;
mutex_lock(&xadc->mutex);
ret = _xadc_update_adc_reg(xadc, reg, mask, val);
mutex_unlock(&xadc->mutex);
return ret;
}
static unsigned long xadc_get_dclk_rate(struct xadc *xadc)
{
return xadc->ops->get_dclk_rate(xadc);
}
static int xadc_update_scan_mode(struct iio_dev *indio_dev,
const unsigned long *mask)
{
struct xadc *xadc = iio_priv(indio_dev);
size_t new_size, n;
void *data;
n = bitmap_weight(mask, indio_dev->masklength);
if (check_mul_overflow(n, sizeof(*xadc->data), &new_size))
return -ENOMEM;
data = devm_krealloc(indio_dev->dev.parent, xadc->data,
new_size, GFP_KERNEL);
if (!data)
return -ENOMEM;
memset(data, 0, new_size);
xadc->data = data;
return 0;
}
static unsigned int xadc_scan_index_to_channel(unsigned int scan_index)
{
switch (scan_index) {
case 5:
return XADC_REG_VCCPINT;
case 6:
return XADC_REG_VCCPAUX;
case 7:
return XADC_REG_VCCO_DDR;
case 8:
return XADC_REG_TEMP;
case 9:
return XADC_REG_VCCINT;
case 10:
return XADC_REG_VCCAUX;
case 11:
return XADC_REG_VPVN;
case 12:
return XADC_REG_VREFP;
case 13:
return XADC_REG_VREFN;
case 14:
return XADC_REG_VCCBRAM;
default:
return XADC_REG_VAUX(scan_index - 16);
}
}
static irqreturn_t xadc_trigger_handler(int irq, void *p)
{
struct iio_poll_func *pf = p;
struct iio_dev *indio_dev = pf->indio_dev;
struct xadc *xadc = iio_priv(indio_dev);
unsigned int chan;
int i, j;
if (!xadc->data)
goto out;
j = 0;
for_each_set_bit(i, indio_dev->active_scan_mask,
indio_dev->masklength) {
chan = xadc_scan_index_to_channel(i);
xadc_read_adc_reg(xadc, chan, &xadc->data[j]);
j++;
}
iio_push_to_buffers(indio_dev, xadc->data);
out:
iio_trigger_notify_done(indio_dev->trig);
return IRQ_HANDLED;
}
static int xadc_trigger_set_state(struct iio_trigger *trigger, bool state)
{
struct xadc *xadc = iio_trigger_get_drvdata(trigger);
unsigned long flags;
unsigned int convst;
unsigned int val;
int ret = 0;
mutex_lock(&xadc->mutex);
if (state) {
/* Only one of the two triggers can be active at a time. */
if (xadc->trigger != NULL) {
ret = -EBUSY;
goto err_out;
} else {
xadc->trigger = trigger;
if (trigger == xadc->convst_trigger)
convst = XADC_CONF0_EC;
else
convst = 0;
}
ret = _xadc_update_adc_reg(xadc, XADC_REG_CONF1, XADC_CONF0_EC,
convst);
if (ret)
goto err_out;
} else {
xadc->trigger = NULL;
}
spin_lock_irqsave(&xadc->lock, flags);
xadc_read_reg(xadc, XADC_AXI_REG_IPIER, &val);
xadc_write_reg(xadc, XADC_AXI_REG_IPISR, XADC_AXI_INT_EOS);
if (state)
val |= XADC_AXI_INT_EOS;
else
val &= ~XADC_AXI_INT_EOS;
xadc_write_reg(xadc, XADC_AXI_REG_IPIER, val);
spin_unlock_irqrestore(&xadc->lock, flags);
err_out:
mutex_unlock(&xadc->mutex);
return ret;
}
static const struct iio_trigger_ops xadc_trigger_ops = {
.set_trigger_state = &xadc_trigger_set_state,
};
static struct iio_trigger *xadc_alloc_trigger(struct iio_dev *indio_dev,
const char *name)
{
struct device *dev = indio_dev->dev.parent;
struct iio_trigger *trig;
int ret;
trig = devm_iio_trigger_alloc(dev, "%s%d-%s", indio_dev->name,
iio_device_id(indio_dev), name);
if (trig == NULL)
return ERR_PTR(-ENOMEM);
trig->ops = &xadc_trigger_ops;
iio_trigger_set_drvdata(trig, iio_priv(indio_dev));
ret = devm_iio_trigger_register(dev, trig);
if (ret)
return ERR_PTR(ret);
return trig;
}
static int xadc_power_adc_b(struct xadc *xadc, unsigned int seq_mode)
{
uint16_t val;
/*
* As per datasheet the power-down bits are don't care in the
* UltraScale, but as per reality setting the power-down bit for the
* non-existing ADC-B powers down the main ADC, so just return and don't
* do anything.
*/
if (xadc->ops->type == XADC_TYPE_US)
return 0;
/* Powerdown the ADC-B when it is not needed. */
switch (seq_mode) {
case XADC_CONF1_SEQ_SIMULTANEOUS:
case XADC_CONF1_SEQ_INDEPENDENT:
val = 0;
break;
default:
val = XADC_CONF2_PD_ADC_B;
break;
}
return xadc_update_adc_reg(xadc, XADC_REG_CONF2, XADC_CONF2_PD_MASK,
val);
}
static int xadc_get_seq_mode(struct xadc *xadc, unsigned long scan_mode)
{
unsigned int aux_scan_mode = scan_mode >> 16;
/* UltraScale has only one ADC and supports only continuous mode */
if (xadc->ops->type == XADC_TYPE_US)
return XADC_CONF1_SEQ_CONTINUOUS;
if (xadc->external_mux_mode == XADC_EXTERNAL_MUX_DUAL)
return XADC_CONF1_SEQ_SIMULTANEOUS;
if ((aux_scan_mode & 0xff00) == 0 ||
(aux_scan_mode & 0x00ff) == 0)
return XADC_CONF1_SEQ_CONTINUOUS;
return XADC_CONF1_SEQ_SIMULTANEOUS;
}
static int xadc_postdisable(struct iio_dev *indio_dev)
{
struct xadc *xadc = iio_priv(indio_dev);
unsigned long scan_mask;
int ret;
int i;
scan_mask = 1; /* Run calibration as part of the sequence */
for (i = 0; i < indio_dev->num_channels; i++)
scan_mask |= BIT(indio_dev->channels[i].scan_index);
/* Enable all channels and calibration */
ret = xadc_write_adc_reg(xadc, XADC_REG_SEQ(0), scan_mask & 0xffff);
if (ret)
return ret;
ret = xadc_write_adc_reg(xadc, XADC_REG_SEQ(1), scan_mask >> 16);
if (ret)
return ret;
ret = xadc_update_adc_reg(xadc, XADC_REG_CONF1, XADC_CONF1_SEQ_MASK,
XADC_CONF1_SEQ_CONTINUOUS);
if (ret)
return ret;
return xadc_power_adc_b(xadc, XADC_CONF1_SEQ_CONTINUOUS);
}
static int xadc_preenable(struct iio_dev *indio_dev)
{
struct xadc *xadc = iio_priv(indio_dev);
unsigned long scan_mask;
int seq_mode;
int ret;
ret = xadc_update_adc_reg(xadc, XADC_REG_CONF1, XADC_CONF1_SEQ_MASK,
XADC_CONF1_SEQ_DEFAULT);
if (ret)
goto err;
scan_mask = *indio_dev->active_scan_mask;
seq_mode = xadc_get_seq_mode(xadc, scan_mask);
ret = xadc_write_adc_reg(xadc, XADC_REG_SEQ(0), scan_mask & 0xffff);
if (ret)
goto err;
/*
* In simultaneous mode the upper and lower aux channels are samples at
* the same time. In this mode the upper 8 bits in the sequencer
* register are don't care and the lower 8 bits control two channels
* each. As such we must set the bit if either the channel in the lower
* group or the upper group is enabled.
*/
if (seq_mode == XADC_CONF1_SEQ_SIMULTANEOUS)
scan_mask = ((scan_mask >> 8) | scan_mask) & 0xff0000;
ret = xadc_write_adc_reg(xadc, XADC_REG_SEQ(1), scan_mask >> 16);
if (ret)
goto err;
ret = xadc_power_adc_b(xadc, seq_mode);
if (ret)
goto err;
ret = xadc_update_adc_reg(xadc, XADC_REG_CONF1, XADC_CONF1_SEQ_MASK,
seq_mode);
if (ret)
goto err;
return 0;
err:
xadc_postdisable(indio_dev);
return ret;
}
static const struct iio_buffer_setup_ops xadc_buffer_ops = {
.preenable = &xadc_preenable,
.postdisable = &xadc_postdisable,
};
static int xadc_read_samplerate(struct xadc *xadc)
{
unsigned int div;
uint16_t val16;
int ret;
ret = xadc_read_adc_reg(xadc, XADC_REG_CONF2, &val16);
if (ret)
return ret;
div = (val16 & XADC_CONF2_DIV_MASK) >> XADC_CONF2_DIV_OFFSET;
if (div < 2)
div = 2;
return xadc_get_dclk_rate(xadc) / div / 26;
}
static int xadc_read_raw(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan, int *val, int *val2, long info)
{
struct xadc *xadc = iio_priv(indio_dev);
unsigned int bits = chan->scan_type.realbits;
uint16_t val16;
int ret;
switch (info) {
case IIO_CHAN_INFO_RAW:
if (iio_buffer_enabled(indio_dev))
return -EBUSY;
ret = xadc_read_adc_reg(xadc, chan->address, &val16);
if (ret < 0)
return ret;
val16 >>= chan->scan_type.shift;
if (chan->scan_type.sign == 'u')
*val = val16;
else
*val = sign_extend32(val16, bits - 1);
return IIO_VAL_INT;
case IIO_CHAN_INFO_SCALE:
switch (chan->type) {
case IIO_VOLTAGE:
/* V = (val * 3.0) / 2**bits */
switch (chan->address) {
case XADC_REG_VCCINT:
case XADC_REG_VCCAUX:
case XADC_REG_VREFP:
case XADC_REG_VREFN:
case XADC_REG_VCCBRAM:
case XADC_REG_VCCPINT:
case XADC_REG_VCCPAUX:
case XADC_REG_VCCO_DDR:
*val = 3000;
break;
default:
*val = 1000;
break;
}
*val2 = bits;
return IIO_VAL_FRACTIONAL_LOG2;
case IIO_TEMP:
/* Temp in C = (val * 503.975) / 2**bits - 273.15 */
*val = 503975;
*val2 = bits;
return IIO_VAL_FRACTIONAL_LOG2;
default:
return -EINVAL;
}
case IIO_CHAN_INFO_OFFSET:
/* Only the temperature channel has an offset */
*val = -((273150 << bits) / 503975);
return IIO_VAL_INT;
case IIO_CHAN_INFO_SAMP_FREQ:
ret = xadc_read_samplerate(xadc);
if (ret < 0)
return ret;
*val = ret;
return IIO_VAL_INT;
default:
return -EINVAL;
}
}
static int xadc_write_samplerate(struct xadc *xadc, int val)
{
unsigned long clk_rate = xadc_get_dclk_rate(xadc);
unsigned int div;
if (!clk_rate)
return -EINVAL;
if (val <= 0)
return -EINVAL;
/* Max. 150 kSPS */
if (val > XADC_MAX_SAMPLERATE)
val = XADC_MAX_SAMPLERATE;
val *= 26;
/* Min 1MHz */
if (val < 1000000)
val = 1000000;
/*
* We want to round down, but only if we do not exceed the 150 kSPS
* limit.
*/
div = clk_rate / val;
if (clk_rate / div / 26 > XADC_MAX_SAMPLERATE)
div++;
if (div < 2)
div = 2;
else if (div > 0xff)
div = 0xff;
return xadc_update_adc_reg(xadc, XADC_REG_CONF2, XADC_CONF2_DIV_MASK,
div << XADC_CONF2_DIV_OFFSET);
}
static int xadc_write_raw(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan, int val, int val2, long info)
{
struct xadc *xadc = iio_priv(indio_dev);
if (info != IIO_CHAN_INFO_SAMP_FREQ)
return -EINVAL;
return xadc_write_samplerate(xadc, val);
}
static const struct iio_event_spec xadc_temp_events[] = {
{
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_RISING,
.mask_separate = BIT(IIO_EV_INFO_ENABLE) |
BIT(IIO_EV_INFO_VALUE) |
BIT(IIO_EV_INFO_HYSTERESIS),
},
};
/* Separate values for upper and lower thresholds, but only a shared enabled */
static const struct iio_event_spec xadc_voltage_events[] = {
{
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_RISING,
.mask_separate = BIT(IIO_EV_INFO_VALUE),
}, {
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_FALLING,
.mask_separate = BIT(IIO_EV_INFO_VALUE),
}, {
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_EITHER,
.mask_separate = BIT(IIO_EV_INFO_ENABLE),
},
};
#define XADC_CHAN_TEMP(_chan, _scan_index, _addr, _bits) { \
.type = IIO_TEMP, \
.indexed = 1, \
.channel = (_chan), \
.address = (_addr), \
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
BIT(IIO_CHAN_INFO_SCALE) | \
BIT(IIO_CHAN_INFO_OFFSET), \
.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), \
.event_spec = xadc_temp_events, \
.num_event_specs = ARRAY_SIZE(xadc_temp_events), \
.scan_index = (_scan_index), \
.scan_type = { \
.sign = 'u', \
.realbits = (_bits), \
.storagebits = 16, \
.shift = 16 - (_bits), \
.endianness = IIO_CPU, \
}, \
}
#define XADC_CHAN_VOLTAGE(_chan, _scan_index, _addr, _bits, _ext, _alarm) { \
.type = IIO_VOLTAGE, \
.indexed = 1, \
.channel = (_chan), \
.address = (_addr), \
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
BIT(IIO_CHAN_INFO_SCALE), \
.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), \
.event_spec = (_alarm) ? xadc_voltage_events : NULL, \
.num_event_specs = (_alarm) ? ARRAY_SIZE(xadc_voltage_events) : 0, \
.scan_index = (_scan_index), \
.scan_type = { \
.sign = ((_addr) == XADC_REG_VREFN) ? 's' : 'u', \
.realbits = (_bits), \
.storagebits = 16, \
.shift = 16 - (_bits), \
.endianness = IIO_CPU, \
}, \
.extend_name = _ext, \
}
/* 7 Series */
#define XADC_7S_CHAN_TEMP(_chan, _scan_index, _addr) \
XADC_CHAN_TEMP(_chan, _scan_index, _addr, 12)
#define XADC_7S_CHAN_VOLTAGE(_chan, _scan_index, _addr, _ext, _alarm) \
XADC_CHAN_VOLTAGE(_chan, _scan_index, _addr, 12, _ext, _alarm)
static const struct iio_chan_spec xadc_7s_channels[] = {
XADC_7S_CHAN_TEMP(0, 8, XADC_REG_TEMP),
XADC_7S_CHAN_VOLTAGE(0, 9, XADC_REG_VCCINT, "vccint", true),
XADC_7S_CHAN_VOLTAGE(1, 10, XADC_REG_VCCAUX, "vccaux", true),
XADC_7S_CHAN_VOLTAGE(2, 14, XADC_REG_VCCBRAM, "vccbram", true),
XADC_7S_CHAN_VOLTAGE(3, 5, XADC_REG_VCCPINT, "vccpint", true),
XADC_7S_CHAN_VOLTAGE(4, 6, XADC_REG_VCCPAUX, "vccpaux", true),
XADC_7S_CHAN_VOLTAGE(5, 7, XADC_REG_VCCO_DDR, "vccoddr", true),
XADC_7S_CHAN_VOLTAGE(6, 12, XADC_REG_VREFP, "vrefp", false),
XADC_7S_CHAN_VOLTAGE(7, 13, XADC_REG_VREFN, "vrefn", false),
XADC_7S_CHAN_VOLTAGE(8, 11, XADC_REG_VPVN, NULL, false),
XADC_7S_CHAN_VOLTAGE(9, 16, XADC_REG_VAUX(0), NULL, false),
XADC_7S_CHAN_VOLTAGE(10, 17, XADC_REG_VAUX(1), NULL, false),
XADC_7S_CHAN_VOLTAGE(11, 18, XADC_REG_VAUX(2), NULL, false),
XADC_7S_CHAN_VOLTAGE(12, 19, XADC_REG_VAUX(3), NULL, false),
XADC_7S_CHAN_VOLTAGE(13, 20, XADC_REG_VAUX(4), NULL, false),
XADC_7S_CHAN_VOLTAGE(14, 21, XADC_REG_VAUX(5), NULL, false),
XADC_7S_CHAN_VOLTAGE(15, 22, XADC_REG_VAUX(6), NULL, false),
XADC_7S_CHAN_VOLTAGE(16, 23, XADC_REG_VAUX(7), NULL, false),
XADC_7S_CHAN_VOLTAGE(17, 24, XADC_REG_VAUX(8), NULL, false),
XADC_7S_CHAN_VOLTAGE(18, 25, XADC_REG_VAUX(9), NULL, false),
XADC_7S_CHAN_VOLTAGE(19, 26, XADC_REG_VAUX(10), NULL, false),
XADC_7S_CHAN_VOLTAGE(20, 27, XADC_REG_VAUX(11), NULL, false),
XADC_7S_CHAN_VOLTAGE(21, 28, XADC_REG_VAUX(12), NULL, false),
XADC_7S_CHAN_VOLTAGE(22, 29, XADC_REG_VAUX(13), NULL, false),
XADC_7S_CHAN_VOLTAGE(23, 30, XADC_REG_VAUX(14), NULL, false),
XADC_7S_CHAN_VOLTAGE(24, 31, XADC_REG_VAUX(15), NULL, false),
};
/* UltraScale */
#define XADC_US_CHAN_TEMP(_chan, _scan_index, _addr) \
XADC_CHAN_TEMP(_chan, _scan_index, _addr, 10)
#define XADC_US_CHAN_VOLTAGE(_chan, _scan_index, _addr, _ext, _alarm) \
XADC_CHAN_VOLTAGE(_chan, _scan_index, _addr, 10, _ext, _alarm)
static const struct iio_chan_spec xadc_us_channels[] = {
XADC_US_CHAN_TEMP(0, 8, XADC_REG_TEMP),
XADC_US_CHAN_VOLTAGE(0, 9, XADC_REG_VCCINT, "vccint", true),
XADC_US_CHAN_VOLTAGE(1, 10, XADC_REG_VCCAUX, "vccaux", true),
XADC_US_CHAN_VOLTAGE(2, 14, XADC_REG_VCCBRAM, "vccbram", true),
XADC_US_CHAN_VOLTAGE(3, 5, XADC_REG_VCCPINT, "vccpsintlp", true),
XADC_US_CHAN_VOLTAGE(4, 6, XADC_REG_VCCPAUX, "vccpsintfp", true),
XADC_US_CHAN_VOLTAGE(5, 7, XADC_REG_VCCO_DDR, "vccpsaux", true),
XADC_US_CHAN_VOLTAGE(6, 12, XADC_REG_VREFP, "vrefp", false),
XADC_US_CHAN_VOLTAGE(7, 13, XADC_REG_VREFN, "vrefn", false),
XADC_US_CHAN_VOLTAGE(8, 11, XADC_REG_VPVN, NULL, false),
XADC_US_CHAN_VOLTAGE(9, 16, XADC_REG_VAUX(0), NULL, false),
XADC_US_CHAN_VOLTAGE(10, 17, XADC_REG_VAUX(1), NULL, false),
XADC_US_CHAN_VOLTAGE(11, 18, XADC_REG_VAUX(2), NULL, false),
XADC_US_CHAN_VOLTAGE(12, 19, XADC_REG_VAUX(3), NULL, false),
XADC_US_CHAN_VOLTAGE(13, 20, XADC_REG_VAUX(4), NULL, false),
XADC_US_CHAN_VOLTAGE(14, 21, XADC_REG_VAUX(5), NULL, false),
XADC_US_CHAN_VOLTAGE(15, 22, XADC_REG_VAUX(6), NULL, false),
XADC_US_CHAN_VOLTAGE(16, 23, XADC_REG_VAUX(7), NULL, false),
XADC_US_CHAN_VOLTAGE(17, 24, XADC_REG_VAUX(8), NULL, false),
XADC_US_CHAN_VOLTAGE(18, 25, XADC_REG_VAUX(9), NULL, false),
XADC_US_CHAN_VOLTAGE(19, 26, XADC_REG_VAUX(10), NULL, false),
XADC_US_CHAN_VOLTAGE(20, 27, XADC_REG_VAUX(11), NULL, false),
XADC_US_CHAN_VOLTAGE(21, 28, XADC_REG_VAUX(12), NULL, false),
XADC_US_CHAN_VOLTAGE(22, 29, XADC_REG_VAUX(13), NULL, false),
XADC_US_CHAN_VOLTAGE(23, 30, XADC_REG_VAUX(14), NULL, false),
XADC_US_CHAN_VOLTAGE(24, 31, XADC_REG_VAUX(15), NULL, false),
};
static const struct iio_info xadc_info = {
.read_raw = &xadc_read_raw,
.write_raw = &xadc_write_raw,
.read_event_config = &xadc_read_event_config,
.write_event_config = &xadc_write_event_config,
.read_event_value = &xadc_read_event_value,
.write_event_value = &xadc_write_event_value,
.update_scan_mode = &xadc_update_scan_mode,
};
static const struct of_device_id xadc_of_match_table[] = {
{
.compatible = "xlnx,zynq-xadc-1.00.a",
.data = &xadc_zynq_ops
}, {
.compatible = "xlnx,axi-xadc-1.00.a",
.data = &xadc_7s_axi_ops
}, {
.compatible = "xlnx,system-management-wiz-1.3",
.data = &xadc_us_axi_ops
},
{ },
};
MODULE_DEVICE_TABLE(of, xadc_of_match_table);
static int xadc_parse_dt(struct iio_dev *indio_dev, unsigned int *conf, int irq)
{
struct device *dev = indio_dev->dev.parent;
struct xadc *xadc = iio_priv(indio_dev);
const struct iio_chan_spec *channel_templates;
struct iio_chan_spec *channels, *chan;
struct fwnode_handle *chan_node, *child;
unsigned int max_channels;
unsigned int num_channels;
const char *external_mux;
u32 ext_mux_chan;
u32 reg;
int ret;
int i;
*conf = 0;
ret = device_property_read_string(dev, "xlnx,external-mux", &external_mux);
if (ret < 0 || strcasecmp(external_mux, "none") == 0)
xadc->external_mux_mode = XADC_EXTERNAL_MUX_NONE;
else if (strcasecmp(external_mux, "single") == 0)
xadc->external_mux_mode = XADC_EXTERNAL_MUX_SINGLE;
else if (strcasecmp(external_mux, "dual") == 0)
xadc->external_mux_mode = XADC_EXTERNAL_MUX_DUAL;
else
return -EINVAL;
if (xadc->external_mux_mode != XADC_EXTERNAL_MUX_NONE) {
ret = device_property_read_u32(dev, "xlnx,external-mux-channel", &ext_mux_chan);
if (ret < 0)
return ret;
if (xadc->external_mux_mode == XADC_EXTERNAL_MUX_SINGLE) {
if (ext_mux_chan == 0)
ext_mux_chan = XADC_REG_VPVN;
else if (ext_mux_chan <= 16)
ext_mux_chan = XADC_REG_VAUX(ext_mux_chan - 1);
else
return -EINVAL;
} else {
if (ext_mux_chan > 0 && ext_mux_chan <= 8)
ext_mux_chan = XADC_REG_VAUX(ext_mux_chan - 1);
else
return -EINVAL;
}
*conf |= XADC_CONF0_MUX | XADC_CONF0_CHAN(ext_mux_chan);
}
if (xadc->ops->type == XADC_TYPE_S7) {
channel_templates = xadc_7s_channels;
max_channels = ARRAY_SIZE(xadc_7s_channels);
} else {
channel_templates = xadc_us_channels;
max_channels = ARRAY_SIZE(xadc_us_channels);
}
channels = devm_kmemdup(dev, channel_templates,
sizeof(channels[0]) * max_channels, GFP_KERNEL);
if (!channels)
return -ENOMEM;
num_channels = 9;
chan = &channels[9];
chan_node = device_get_named_child_node(dev, "xlnx,channels");
fwnode_for_each_child_node(chan_node, child) {
if (num_channels >= max_channels) {
fwnode_handle_put(child);
break;
}
ret = fwnode_property_read_u32(child, "reg", &reg);
if (ret || reg > 16)
continue;
if (fwnode_property_read_bool(child, "xlnx,bipolar"))
chan->scan_type.sign = 's';
if (reg == 0) {
chan->scan_index = 11;
chan->address = XADC_REG_VPVN;
} else {
chan->scan_index = 15 + reg;
chan->address = XADC_REG_VAUX(reg - 1);
}
num_channels++;
chan++;
}
fwnode_handle_put(chan_node);
/* No IRQ => no events */
if (irq <= 0) {
for (i = 0; i < num_channels; i++) {
channels[i].event_spec = NULL;
channels[i].num_event_specs = 0;
}
}
indio_dev->num_channels = num_channels;
indio_dev->channels = devm_krealloc(dev, channels,
sizeof(*channels) * num_channels,
GFP_KERNEL);
/* If we can't resize the channels array, just use the original */
if (!indio_dev->channels)
indio_dev->channels = channels;
return 0;
}
static const char * const xadc_type_names[] = {
[XADC_TYPE_S7] = "xadc",
[XADC_TYPE_US] = "xilinx-system-monitor",
};
static void xadc_clk_disable_unprepare(void *data)
{
struct clk *clk = data;
clk_disable_unprepare(clk);
}
static void xadc_cancel_delayed_work(void *data)
{
struct delayed_work *work = data;
cancel_delayed_work_sync(work);
}
static int xadc_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
const struct xadc_ops *ops;
struct iio_dev *indio_dev;
unsigned int bipolar_mask;
unsigned int conf0;
struct xadc *xadc;
int ret;
int irq;
int i;
ops = device_get_match_data(dev);
if (!ops)
return -EINVAL;
irq = platform_get_irq_optional(pdev, 0);
if (irq < 0 &&
(irq != -ENXIO || !(ops->flags & XADC_FLAGS_IRQ_OPTIONAL)))
return irq;
indio_dev = devm_iio_device_alloc(dev, sizeof(*xadc));
if (!indio_dev)
return -ENOMEM;
xadc = iio_priv(indio_dev);
xadc->ops = ops;
init_completion(&xadc->completion);
mutex_init(&xadc->mutex);
spin_lock_init(&xadc->lock);
INIT_DELAYED_WORK(&xadc->zynq_unmask_work, xadc_zynq_unmask_worker);
xadc->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(xadc->base))
return PTR_ERR(xadc->base);
indio_dev->name = xadc_type_names[xadc->ops->type];
indio_dev->modes = INDIO_DIRECT_MODE;
indio_dev->info = &xadc_info;
ret = xadc_parse_dt(indio_dev, &conf0, irq);
if (ret)
return ret;
if (xadc->ops->flags & XADC_FLAGS_BUFFERED) {
ret = devm_iio_triggered_buffer_setup(dev, indio_dev,
&iio_pollfunc_store_time,
&xadc_trigger_handler,
&xadc_buffer_ops);
if (ret)
return ret;
if (irq > 0) {
xadc->convst_trigger = xadc_alloc_trigger(indio_dev, "convst");
if (IS_ERR(xadc->convst_trigger))
return PTR_ERR(xadc->convst_trigger);
xadc->samplerate_trigger = xadc_alloc_trigger(indio_dev,
"samplerate");
if (IS_ERR(xadc->samplerate_trigger))
return PTR_ERR(xadc->samplerate_trigger);
}
}
xadc->clk = devm_clk_get(dev, NULL);
if (IS_ERR(xadc->clk))
return PTR_ERR(xadc->clk);
ret = clk_prepare_enable(xadc->clk);
if (ret)
return ret;
ret = devm_add_action_or_reset(dev,
xadc_clk_disable_unprepare, xadc->clk);
if (ret)
return ret;
/*
* Make sure not to exceed the maximum samplerate since otherwise the
* resulting interrupt storm will soft-lock the system.
*/
if (xadc->ops->flags & XADC_FLAGS_BUFFERED) {
ret = xadc_read_samplerate(xadc);
if (ret < 0)
return ret;
if (ret > XADC_MAX_SAMPLERATE) {
ret = xadc_write_samplerate(xadc, XADC_MAX_SAMPLERATE);
if (ret < 0)
return ret;
}
}
if (irq > 0) {
ret = devm_request_irq(dev, irq, xadc->ops->interrupt_handler,
0, dev_name(dev), indio_dev);
if (ret)
return ret;
ret = devm_add_action_or_reset(dev, xadc_cancel_delayed_work,
&xadc->zynq_unmask_work);
if (ret)
return ret;
}
ret = xadc->ops->setup(pdev, indio_dev, irq);
if (ret)
return ret;
for (i = 0; i < 16; i++)
xadc_read_adc_reg(xadc, XADC_REG_THRESHOLD(i),
&xadc->threshold[i]);
ret = xadc_write_adc_reg(xadc, XADC_REG_CONF0, conf0);
if (ret)
return ret;
bipolar_mask = 0;
for (i = 0; i < indio_dev->num_channels; i++) {
if (indio_dev->channels[i].scan_type.sign == 's')
bipolar_mask |= BIT(indio_dev->channels[i].scan_index);
}
ret = xadc_write_adc_reg(xadc, XADC_REG_INPUT_MODE(0), bipolar_mask);
if (ret)
return ret;
ret = xadc_write_adc_reg(xadc, XADC_REG_INPUT_MODE(1),
bipolar_mask >> 16);
if (ret)
return ret;
/* Disable all alarms */
ret = xadc_update_adc_reg(xadc, XADC_REG_CONF1, XADC_CONF1_ALARM_MASK,
XADC_CONF1_ALARM_MASK);
if (ret)
return ret;
/* Set thresholds to min/max */
for (i = 0; i < 16; i++) {
/*
* Set max voltage threshold and both temperature thresholds to
* 0xffff, min voltage threshold to 0.
*/
if (i % 8 < 4 || i == 7)
xadc->threshold[i] = 0xffff;
else
xadc->threshold[i] = 0;
ret = xadc_write_adc_reg(xadc, XADC_REG_THRESHOLD(i),
xadc->threshold[i]);
if (ret)
return ret;
}
/* Go to non-buffered mode */
xadc_postdisable(indio_dev);
return devm_iio_device_register(dev, indio_dev);
}
static struct platform_driver xadc_driver = {
.probe = xadc_probe,
.driver = {
.name = "xadc",
.of_match_table = xadc_of_match_table,
},
};
module_platform_driver(xadc_driver);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>");
MODULE_DESCRIPTION("Xilinx XADC IIO driver");