| # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) |
| # Copyright (C) Sunplus Co., Ltd. |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/pinctrl/sunplus,sp7021-pinctrl.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: Sunplus SP7021 Pin Controller |
| |
| maintainers: |
| - Dvorkin Dmitry <dvorkin@tibbo.com> |
| - Wells Lu <wellslutw@gmail.com> |
| |
| description: | |
| The Sunplus SP7021 pin controller is used to control SoC pins. Please |
| refer to pinctrl-bindings.txt in this directory for details of the common |
| pinctrl bindings used by client devices. |
| |
| SP7021 has 99 digital GPIO pins which are numbered from GPIO 0 to 98. All |
| are multiplexed with some special function pins. SP7021 has 3 types of |
| special function pins: |
| |
| (1) function-group pins: |
| Ex 1 (SPI-NOR flash): |
| If control-field SPI_FLASH_SEL is set to 1, GPIO 83, 84, 86 and 87 |
| will be pins of SPI-NOR flash. If it is set to 2, GPIO 76, 78, 79 |
| and 81 will be pins of SPI-NOR flash. |
| |
| Ex 2 (UART_0): |
| If control-bit UA0_SEL is set to 1, GPIO 88 and 89 will be TX and |
| RX pins of UART_0 (UART channel 0). |
| |
| Ex 3 (eMMC): |
| If control-bit EMMC_SEL is set to 1, GPIO 72, 73, 74, 75, 76, 77, |
| 78, 79, 80, 81 will be pins of an eMMC device. |
| |
| Properties "function" and "groups" are used to select function-group |
| pins. |
| |
| (2) fully pin-mux (like phone exchange mux) pins: |
| GPIO 8 to 71 are 'fully pin-mux' pins. Any pins of peripherals of |
| SP7021 (ex: UART_1, UART_2, UART_3, UART_4, I2C_0, I2C_1, and etc.) |
| can be routed to any pins of fully pin-mux pins. |
| |
| Ex 1 (UART channel 1): |
| If control-field UA1_TX_SEL is set to 3, TX pin of UART_1 will be |
| routed to GPIO 10 (3 - 1 + 8 = 10). |
| If control-field UA1_RX_SEL is set to 4, RX pin of UART_1 will be |
| routed to GPIO 11 (4 - 1 + 8 = 11). |
| If control-field UA1_RTS_SEL is set to 5, RTS pin of UART_1 will |
| be routed to GPIO 12 (5 - 1 + 8 = 12). |
| If control-field UA1_CTS_SEL is set to 6, CTS pin of UART_1 will |
| be routed to GPIO 13 (6 - 1 + 8 = 13). |
| |
| Ex 2 (I2C channel 0): |
| If control-field I2C0_CLK_SEL is set to 20, CLK pin of I2C_0 will |
| be routed to GPIO 27 (20 - 1 + 8 = 27). |
| If control-field I2C0_DATA_SEL is set to 21, DATA pin of I2C_0 |
| will be routed to GPIO 28 (21 - 1 + 9 = 28). |
| |
| Totally, SP7021 has 120 peripheral pins. The peripheral pins can be |
| routed to any of 64 'fully pin-mux' pins. |
| |
| (3) I/O processor pins |
| SP7021 has a built-in I/O processor. |
| Any GPIO pins (GPIO 0 to 98) can be set to pins of I/O processor. |
| |
| Vendor property "sunplus,pins" is used to select "fully pin-mux" pins, |
| "I/O processor pins" and "digital GPIO" pins. |
| |
| The device node of pin controller of Sunplus SP7021 has following |
| properties. |
| |
| properties: |
| compatible: |
| const: sunplus,sp7021-pctl |
| |
| gpio-controller: true |
| |
| '#gpio-cells': |
| const: 2 |
| |
| reg: |
| items: |
| - description: the MOON2 registers |
| - description: the GPIOXT registers |
| - description: the FIRST registers |
| - description: the MOON1 registers |
| |
| reg-names: |
| items: |
| - const: moon2 |
| - const: gpioxt |
| - const: first |
| - const: moon1 |
| |
| clocks: |
| maxItems: 1 |
| |
| resets: |
| maxItems: 1 |
| |
| patternProperties: |
| '-pins$': |
| type: object |
| description: | |
| A pinctrl node should contain at least one subnodes representing the |
| pins or function-pins group available on the machine. Each subnode |
| will list the pins it needs, and how they should be configured. |
| |
| Pinctrl node's client devices use subnodes for desired pin |
| configuration. Client device subnodes use below standard properties. |
| $ref: pinmux-node.yaml# |
| |
| properties: |
| sunplus,pins: |
| description: | |
| Define 'sunplus,pins' which are used by pinctrl node's client |
| device. |
| |
| It consists of one or more integers which represents the config |
| setting for corresponding pin. Each integer defines a individual |
| pin in which: |
| |
| Bit 32~24: defines GPIO number. Its range is 0 ~ 98. |
| Bit 23~16: defines types: (1) fully pin-mux pins |
| (2) IO processor pins |
| (3) digital GPIO pins |
| Bit 15~8: defines pins of peripherals (which are defined in |
| 'include/dt-binging/pinctrl/sppctl.h'). |
| Bit 7~0: defines types or initial-state of digital GPIO pins. |
| |
| Please use macro SPPCTL_IOPAD to define the integers for pins. |
| |
| $ref: /schemas/types.yaml#/definitions/uint32-array |
| |
| function: |
| description: | |
| Define pin-function which is used by pinctrl node's client device. |
| The name should be one of string in the following enumeration. |
| $ref: "/schemas/types.yaml#/definitions/string" |
| enum: [ SPI_FLASH, SPI_FLASH_4BIT, SPI_NAND, CARD0_EMMC, SD_CARD, |
| UA0, FPGA_IFX, HDMI_TX, LCDIF, USB0_OTG, USB1_OTG ] |
| |
| groups: |
| description: | |
| Define pin-group in a specified pin-function. |
| The name should be one of string in the following enumeration. |
| $ref: "/schemas/types.yaml#/definitions/string" |
| enum: [ SPI_FLASH1, SPI_FLASH2, SPI_FLASH_4BIT1, SPI_FLASH_4BIT2, |
| SPI_NAND, CARD0_EMMC, SD_CARD, UA0, FPGA_IFX, HDMI_TX1, |
| HDMI_TX2, HDMI_TX3, LCDIF, USB0_OTG, USB1_OTG ] |
| |
| sunplus,zerofunc: |
| description: | |
| This is a vendor specific property. It is used to disable pins |
| which are not used by pinctrl node's client device. |
| Some pins may be enabled by boot-loader. We can use this |
| property to disable them. |
| $ref: /schemas/types.yaml#/definitions/uint32-array |
| |
| additionalProperties: false |
| |
| allOf: |
| - if: |
| properties: |
| function: |
| enum: |
| - SPI_FLASH |
| then: |
| properties: |
| groups: |
| enum: |
| - SPI_FLASH1 |
| - SPI_FLASH2 |
| - if: |
| properties: |
| function: |
| enum: |
| - SPI_FLASH_4BIT |
| then: |
| properties: |
| groups: |
| enum: |
| - SPI_FLASH_4BIT1 |
| - SPI_FLASH_4BIT2 |
| - if: |
| properties: |
| function: |
| enum: |
| - SPI_NAND |
| then: |
| properties: |
| groups: |
| enum: |
| - SPI_NAND |
| - if: |
| properties: |
| function: |
| enum: |
| - CARD0_EMMC |
| then: |
| properties: |
| groups: |
| enum: |
| - CARD0_EMMC |
| - if: |
| properties: |
| function: |
| enum: |
| - SD_CARD |
| then: |
| properties: |
| groups: |
| enum: |
| - SD_CARD |
| - if: |
| properties: |
| function: |
| enum: |
| - UA0 |
| then: |
| properties: |
| groups: |
| enum: |
| - UA0 |
| - if: |
| properties: |
| function: |
| enum: |
| - FPGA_IFX |
| then: |
| properties: |
| groups: |
| enum: |
| - FPGA_IFX |
| - if: |
| properties: |
| function: |
| enum: |
| - HDMI_TX |
| then: |
| properties: |
| groups: |
| enum: |
| - HDMI_TX1 |
| - HDMI_TX2 |
| - HDMI_TX3 |
| - if: |
| properties: |
| function: |
| enum: |
| - LCDIF |
| then: |
| properties: |
| groups: |
| enum: |
| - LCDIF |
| - if: |
| properties: |
| function: |
| enum: |
| - USB0_OTG |
| then: |
| properties: |
| groups: |
| enum: |
| - USB0_OTG |
| - if: |
| properties: |
| function: |
| enum: |
| - USB1_OTG |
| then: |
| properties: |
| groups: |
| enum: |
| - USB1_OTG |
| |
| required: |
| - compatible |
| - reg |
| - reg-names |
| - "#gpio-cells" |
| - gpio-controller |
| - clocks |
| - resets |
| |
| additionalProperties: false |
| |
| allOf: |
| - $ref: "pinctrl.yaml#" |
| |
| examples: |
| - | |
| #include <dt-bindings/pinctrl/sppctl-sp7021.h> |
| |
| pinctrl@9c000100 { |
| compatible = "sunplus,sp7021-pctl"; |
| reg = <0x9c000100 0x100>, <0x9c000300 0x100>, |
| <0x9c0032e4 0x1c>, <0x9c000080 0x20>; |
| reg-names = "moon2", "gpioxt", "first", "moon1"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| clocks = <&clkc 0x83>; |
| resets = <&rstc 0x73>; |
| |
| uart0-pins { |
| function = "UA0"; |
| groups = "UA0"; |
| }; |
| |
| spinand0-pins { |
| function = "SPI_NAND"; |
| groups = "SPI_NAND"; |
| }; |
| |
| uart1-pins { |
| sunplus,pins = < |
| SPPCTL_IOPAD(11, SPPCTL_PCTL_G_PMUX, MUXF_UA1_TX, 0) |
| SPPCTL_IOPAD(10, SPPCTL_PCTL_G_PMUX, MUXF_UA1_RX, 0) |
| >; |
| }; |
| |
| uart2-pins { |
| sunplus,pins = < |
| SPPCTL_IOPAD(20, SPPCTL_PCTL_G_PMUX, MUXF_UA1_TX, 0) |
| SPPCTL_IOPAD(21, SPPCTL_PCTL_G_PMUX, MUXF_UA1_RX, 0) |
| SPPCTL_IOPAD(22, SPPCTL_PCTL_G_PMUX, MUXF_UA1_RTS, 0) |
| SPPCTL_IOPAD(23, SPPCTL_PCTL_G_PMUX, MUXF_UA1_CTS, 0) |
| >; |
| }; |
| |
| emmc-pins { |
| function = "CARD0_EMMC"; |
| groups = "CARD0_EMMC"; |
| }; |
| |
| sdcard-pins { |
| function = "SD_CARD"; |
| groups = "SD_CARD"; |
| sunplus,pins = < SPPCTL_IOPAD(91, SPPCTL_PCTL_G_GPIO, 0, 0) >; |
| }; |
| |
| hdmi_A_tx1-pins { |
| function = "HDMI_TX"; |
| groups = "HDMI_TX1"; |
| }; |
| hdmi_A_tx2-pins { |
| function = "HDMI_TX"; |
| groups = "HDMI_TX2"; |
| }; |
| hdmi_A_tx3-pins { |
| function = "HDMI_TX"; |
| groups = "HDMI_TX3"; |
| }; |
| |
| ethernet-pins { |
| sunplus,pins = < |
| SPPCTL_IOPAD(49,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_CLK_OUT,0) |
| SPPCTL_IOPAD(44,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_MAC_SMI_MDC,0) |
| SPPCTL_IOPAD(43,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_MAC_SMI_MDIO,0) |
| SPPCTL_IOPAD(52,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXEN,0) |
| SPPCTL_IOPAD(50,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXD0,0) |
| SPPCTL_IOPAD(51,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXD1,0) |
| SPPCTL_IOPAD(46,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_CRSDV,0) |
| SPPCTL_IOPAD(47,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXD0,0) |
| SPPCTL_IOPAD(48,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXD1,0) |
| >; |
| sunplus,zerofunc = < |
| MUXF_L2SW_LED_FLASH0 |
| MUXF_L2SW_LED_ON0 |
| MUXF_L2SW_P0_MAC_RMII_RXER |
| >; |
| }; |
| }; |
| ... |
