| /* |
| * Copyright (C) 2004, 2007-2010, 2011-2012 Synopsys, Inc. (www.synopsys.com) |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| * vineetg: Jan 1011 |
| * -sched_clock( ) no longer jiffies based. Uses the same clocksource |
| * as gtod |
| * |
| * Rajeshwarr/Vineetg: Mar 2008 |
| * -Implemented CONFIG_GENERIC_TIME (rather deleted arch specific code) |
| * for arch independent gettimeofday() |
| * -Implemented CONFIG_GENERIC_CLOCKEVENTS as base for hrtimers |
| * |
| * Vineetg: Mar 2008: Forked off from time.c which now is time-jiff.c |
| */ |
| |
| /* ARC700 has two 32bit independent prog Timers: TIMER0 and TIMER1 |
| * Each can programmed to go from @count to @limit and optionally |
| * interrupt when that happens. |
| * A write to Control Register clears the Interrupt |
| * |
| * We've designated TIMER0 for events (clockevents) |
| * while TIMER1 for free running (clocksource) |
| * |
| * Newer ARC700 cores have 64bit clk fetching RTSC insn, preferred over TIMER1 |
| * which however is currently broken |
| */ |
| |
| #include <linux/interrupt.h> |
| #include <linux/clk.h> |
| #include <linux/clk-provider.h> |
| #include <linux/clocksource.h> |
| #include <linux/clockchips.h> |
| #include <linux/cpu.h> |
| #include <linux/of.h> |
| #include <linux/of_irq.h> |
| #include <asm/irq.h> |
| #include <asm/arcregs.h> |
| |
| #include <asm/mcip.h> |
| |
| /* Timer related Aux registers */ |
| #define ARC_REG_TIMER0_LIMIT 0x23 /* timer 0 limit */ |
| #define ARC_REG_TIMER0_CTRL 0x22 /* timer 0 control */ |
| #define ARC_REG_TIMER0_CNT 0x21 /* timer 0 count */ |
| #define ARC_REG_TIMER1_LIMIT 0x102 /* timer 1 limit */ |
| #define ARC_REG_TIMER1_CTRL 0x101 /* timer 1 control */ |
| #define ARC_REG_TIMER1_CNT 0x100 /* timer 1 count */ |
| |
| #define TIMER_CTRL_IE (1 << 0) /* Interrupt when Count reaches limit */ |
| #define TIMER_CTRL_NH (1 << 1) /* Count only when CPU NOT halted */ |
| |
| #define ARC_TIMER_MAX 0xFFFFFFFF |
| |
| static unsigned long arc_timer_freq; |
| |
| static int noinline arc_get_timer_clk(struct device_node *node) |
| { |
| struct clk *clk; |
| int ret; |
| |
| clk = of_clk_get(node, 0); |
| if (IS_ERR(clk)) { |
| pr_err("timer missing clk"); |
| return PTR_ERR(clk); |
| } |
| |
| ret = clk_prepare_enable(clk); |
| if (ret) { |
| pr_err("Couldn't enable parent clk\n"); |
| return ret; |
| } |
| |
| arc_timer_freq = clk_get_rate(clk); |
| |
| return 0; |
| } |
| |
| /********** Clock Source Device *********/ |
| |
| #ifdef CONFIG_ARC_HAS_GFRC |
| |
| static cycle_t arc_read_gfrc(struct clocksource *cs) |
| { |
| unsigned long flags; |
| union { |
| #ifdef CONFIG_CPU_BIG_ENDIAN |
| struct { u32 h, l; }; |
| #else |
| struct { u32 l, h; }; |
| #endif |
| cycle_t full; |
| } stamp; |
| |
| local_irq_save(flags); |
| |
| __mcip_cmd(CMD_GFRC_READ_LO, 0); |
| stamp.l = read_aux_reg(ARC_REG_MCIP_READBACK); |
| |
| __mcip_cmd(CMD_GFRC_READ_HI, 0); |
| stamp.h = read_aux_reg(ARC_REG_MCIP_READBACK); |
| |
| local_irq_restore(flags); |
| |
| return stamp.full; |
| } |
| |
| static struct clocksource arc_counter_gfrc = { |
| .name = "ARConnect GFRC", |
| .rating = 400, |
| .read = arc_read_gfrc, |
| .mask = CLOCKSOURCE_MASK(64), |
| .flags = CLOCK_SOURCE_IS_CONTINUOUS, |
| }; |
| |
| static int __init arc_cs_setup_gfrc(struct device_node *node) |
| { |
| int exists = cpuinfo_arc700[0].extn.gfrc; |
| int ret; |
| |
| if (WARN(!exists, "Global-64-bit-Ctr clocksource not detected")) |
| return -ENXIO; |
| |
| ret = arc_get_timer_clk(node); |
| if (ret) |
| return ret; |
| |
| return clocksource_register_hz(&arc_counter_gfrc, arc_timer_freq); |
| } |
| CLOCKSOURCE_OF_DECLARE(arc_gfrc, "snps,archs-timer-gfrc", arc_cs_setup_gfrc); |
| |
| #endif |
| |
| #ifdef CONFIG_ARC_HAS_RTC |
| |
| #define AUX_RTC_CTRL 0x103 |
| #define AUX_RTC_LOW 0x104 |
| #define AUX_RTC_HIGH 0x105 |
| |
| static cycle_t arc_read_rtc(struct clocksource *cs) |
| { |
| unsigned long status; |
| union { |
| #ifdef CONFIG_CPU_BIG_ENDIAN |
| struct { u32 high, low; }; |
| #else |
| struct { u32 low, high; }; |
| #endif |
| cycle_t full; |
| } stamp; |
| |
| |
| __asm__ __volatile( |
| "1: \n" |
| " lr %0, [AUX_RTC_LOW] \n" |
| " lr %1, [AUX_RTC_HIGH] \n" |
| " lr %2, [AUX_RTC_CTRL] \n" |
| " bbit0.nt %2, 31, 1b \n" |
| : "=r" (stamp.low), "=r" (stamp.high), "=r" (status)); |
| |
| return stamp.full; |
| } |
| |
| static struct clocksource arc_counter_rtc = { |
| .name = "ARCv2 RTC", |
| .rating = 350, |
| .read = arc_read_rtc, |
| .mask = CLOCKSOURCE_MASK(64), |
| .flags = CLOCK_SOURCE_IS_CONTINUOUS, |
| }; |
| |
| static int __init arc_cs_setup_rtc(struct device_node *node) |
| { |
| int exists = cpuinfo_arc700[smp_processor_id()].extn.rtc; |
| int ret; |
| |
| if (WARN(!exists, "Local-64-bit-Ctr clocksource not detected")) |
| return -ENXIO; |
| |
| /* Local to CPU hence not usable in SMP */ |
| if (WARN(IS_ENABLED(CONFIG_SMP), "Local-64-bit-Ctr not usable in SMP")) |
| return -EINVAL; |
| |
| ret = arc_get_timer_clk(node); |
| if (ret) |
| return ret; |
| |
| write_aux_reg(AUX_RTC_CTRL, 1); |
| |
| return clocksource_register_hz(&arc_counter_rtc, arc_timer_freq); |
| } |
| CLOCKSOURCE_OF_DECLARE(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc); |
| |
| #endif |
| |
| /* |
| * 32bit TIMER1 to keep counting monotonically and wraparound |
| */ |
| |
| static cycle_t arc_read_timer1(struct clocksource *cs) |
| { |
| return (cycle_t) read_aux_reg(ARC_REG_TIMER1_CNT); |
| } |
| |
| static struct clocksource arc_counter_timer1 = { |
| .name = "ARC Timer1", |
| .rating = 300, |
| .read = arc_read_timer1, |
| .mask = CLOCKSOURCE_MASK(32), |
| .flags = CLOCK_SOURCE_IS_CONTINUOUS, |
| }; |
| |
| static int __init arc_cs_setup_timer1(struct device_node *node) |
| { |
| int ret; |
| |
| /* Local to CPU hence not usable in SMP */ |
| if (IS_ENABLED(CONFIG_SMP)) |
| return -EINVAL; |
| |
| ret = arc_get_timer_clk(node); |
| if (ret) |
| return ret; |
| |
| write_aux_reg(ARC_REG_TIMER1_LIMIT, ARC_TIMER_MAX); |
| write_aux_reg(ARC_REG_TIMER1_CNT, 0); |
| write_aux_reg(ARC_REG_TIMER1_CTRL, TIMER_CTRL_NH); |
| |
| return clocksource_register_hz(&arc_counter_timer1, arc_timer_freq); |
| } |
| |
| /********** Clock Event Device *********/ |
| |
| static int arc_timer_irq; |
| |
| /* |
| * Arm the timer to interrupt after @cycles |
| * The distinction for oneshot/periodic is done in arc_event_timer_ack() below |
| */ |
| static void arc_timer_event_setup(unsigned int cycles) |
| { |
| write_aux_reg(ARC_REG_TIMER0_LIMIT, cycles); |
| write_aux_reg(ARC_REG_TIMER0_CNT, 0); /* start from 0 */ |
| |
| write_aux_reg(ARC_REG_TIMER0_CTRL, TIMER_CTRL_IE | TIMER_CTRL_NH); |
| } |
| |
| |
| static int arc_clkevent_set_next_event(unsigned long delta, |
| struct clock_event_device *dev) |
| { |
| arc_timer_event_setup(delta); |
| return 0; |
| } |
| |
| static int arc_clkevent_set_periodic(struct clock_event_device *dev) |
| { |
| /* |
| * At X Hz, 1 sec = 1000ms -> X cycles; |
| * 10ms -> X / 100 cycles |
| */ |
| arc_timer_event_setup(arc_timer_freq / HZ); |
| return 0; |
| } |
| |
| static DEFINE_PER_CPU(struct clock_event_device, arc_clockevent_device) = { |
| .name = "ARC Timer0", |
| .features = CLOCK_EVT_FEAT_ONESHOT | |
| CLOCK_EVT_FEAT_PERIODIC, |
| .rating = 300, |
| .set_next_event = arc_clkevent_set_next_event, |
| .set_state_periodic = arc_clkevent_set_periodic, |
| }; |
| |
| static irqreturn_t timer_irq_handler(int irq, void *dev_id) |
| { |
| /* |
| * Note that generic IRQ core could have passed @evt for @dev_id if |
| * irq_set_chip_and_handler() asked for handle_percpu_devid_irq() |
| */ |
| struct clock_event_device *evt = this_cpu_ptr(&arc_clockevent_device); |
| int irq_reenable = clockevent_state_periodic(evt); |
| |
| /* |
| * Any write to CTRL reg ACks the interrupt, we rewrite the |
| * Count when [N]ot [H]alted bit. |
| * And re-arm it if perioid by [I]nterrupt [E]nable bit |
| */ |
| write_aux_reg(ARC_REG_TIMER0_CTRL, irq_reenable | TIMER_CTRL_NH); |
| |
| evt->event_handler(evt); |
| |
| return IRQ_HANDLED; |
| } |
| |
| |
| static int arc_timer_starting_cpu(unsigned int cpu) |
| { |
| struct clock_event_device *evt = this_cpu_ptr(&arc_clockevent_device); |
| |
| evt->cpumask = cpumask_of(smp_processor_id()); |
| |
| clockevents_config_and_register(evt, arc_timer_freq, 0, ARC_TIMER_MAX); |
| enable_percpu_irq(arc_timer_irq, 0); |
| return 0; |
| } |
| |
| static int arc_timer_dying_cpu(unsigned int cpu) |
| { |
| disable_percpu_irq(arc_timer_irq); |
| return 0; |
| } |
| |
| /* |
| * clockevent setup for boot CPU |
| */ |
| static int __init arc_clockevent_setup(struct device_node *node) |
| { |
| struct clock_event_device *evt = this_cpu_ptr(&arc_clockevent_device); |
| int ret; |
| |
| arc_timer_irq = irq_of_parse_and_map(node, 0); |
| if (arc_timer_irq <= 0) { |
| pr_err("clockevent: missing irq"); |
| return -EINVAL; |
| } |
| |
| ret = arc_get_timer_clk(node); |
| if (ret) { |
| pr_err("clockevent: missing clk"); |
| return ret; |
| } |
| |
| /* Needs apriori irq_set_percpu_devid() done in intc map function */ |
| ret = request_percpu_irq(arc_timer_irq, timer_irq_handler, |
| "Timer0 (per-cpu-tick)", evt); |
| if (ret) { |
| pr_err("clockevent: unable to request irq\n"); |
| return ret; |
| } |
| |
| ret = cpuhp_setup_state(CPUHP_AP_ARC_TIMER_STARTING, |
| "AP_ARC_TIMER_STARTING", |
| arc_timer_starting_cpu, |
| arc_timer_dying_cpu); |
| if (ret) { |
| pr_err("Failed to setup hotplug state"); |
| return ret; |
| } |
| return 0; |
| } |
| |
| static int __init arc_of_timer_init(struct device_node *np) |
| { |
| static int init_count = 0; |
| int ret; |
| |
| if (!init_count) { |
| init_count = 1; |
| ret = arc_clockevent_setup(np); |
| } else { |
| ret = arc_cs_setup_timer1(np); |
| } |
| |
| return ret; |
| } |
| CLOCKSOURCE_OF_DECLARE(arc_clkevt, "snps,arc-timer", arc_of_timer_init); |
| |
| /* |
| * Called from start_kernel() - boot CPU only |
| */ |
| void __init time_init(void) |
| { |
| of_clk_init(NULL); |
| clocksource_probe(); |
| } |