Documentation/power/regulator/consumer.rst - linux - Git at Google

 ===================================
 Regulator Consumer Driver Interface
 ===================================

 This text describes the regulator interface for consumer device drivers.
 Please see overview.txt for a description of the terms used in this text.


 1. Consumer Regulator Access (static & dynamic drivers)
 =======================================================

 A consumer driver can get access to its supply regulator by calling ::

 	regulator = regulator_get(dev, "Vcc");

 The consumer passes in its struct device pointer and power supply ID. The core
 then finds the correct regulator by consulting a machine specific lookup table.
 If the lookup is successful then this call will return a pointer to the struct
 regulator that supplies this consumer.

 To release the regulator the consumer driver should call ::

 	regulator_put(regulator);

 Consumers can be supplied by more than one regulator e.g. codec consumer with
 analog and digital supplies ::

 	digital = regulator_get(dev, "Vcc");  /* digital core */
 	analog = regulator_get(dev, "Avdd");  /* analog */

 The regulator access functions regulator_get() and regulator_put() will
 usually be called in your device drivers probe() and remove() respectively.


 2. Regulator Output Enable & Disable (static & dynamic drivers)
 ===============================================================


 A consumer can enable its power supply by calling::

 	int regulator_enable(regulator);

 NOTE:
   The supply may already be enabled before regulator_enabled() is called.
   This may happen if the consumer shares the regulator or the regulator has been
   previously enabled by bootloader or kernel board initialization code.

 A consumer can determine if a regulator is enabled by calling::

 	int regulator_is_enabled(regulator);

 This will return > zero when the regulator is enabled.


 A consumer can disable its supply when no longer needed by calling::

 	int regulator_disable(regulator);

 NOTE:
   This may not disable the supply if it's shared with other consumers. The
   regulator will only be disabled when the enabled reference count is zero.

 Finally, a regulator can be forcefully disabled in the case of an emergency::

 	int regulator_force_disable(regulator);

 NOTE:
   this will immediately and forcefully shutdown the regulator output. All
   consumers will be powered off.


 3. Regulator Voltage Control & Status (dynamic drivers)
 =======================================================

 Some consumer drivers need to be able to dynamically change their supply
 voltage to match system operating points. e.g. CPUfreq drivers can scale
 voltage along with frequency to save power, SD drivers may need to select the
 correct card voltage, etc.

 Consumers can control their supply voltage by calling::

 	int regulator_set_voltage(regulator, min_uV, max_uV);

 Where min_uV and max_uV are the minimum and maximum acceptable voltages in
 microvolts.

 NOTE: this can be called when the regulator is enabled or disabled. If called
 when enabled, then the voltage changes instantly, otherwise the voltage
 configuration changes and the voltage is physically set when the regulator is
 next enabled.

 The regulators configured voltage output can be found by calling::

 	int regulator_get_voltage(regulator);

 NOTE:
   get_voltage() will return the configured output voltage whether the
   regulator is enabled or disabled and should NOT be used to determine regulator
   output state. However this can be used in conjunction with is_enabled() to
   determine the regulator physical output voltage.


 4. Regulator Current Limit Control & Status (dynamic drivers)
 =============================================================

 Some consumer drivers need to be able to dynamically change their supply
 current limit to match system operating points. e.g. LCD backlight driver can
 change the current limit to vary the backlight brightness, USB drivers may want
 to set the limit to 500mA when supplying power.

 Consumers can control their supply current limit by calling::

 	int regulator_set_current_limit(regulator, min_uA, max_uA);

 Where min_uA and max_uA are the minimum and maximum acceptable current limit in
 microamps.

 NOTE:
   this can be called when the regulator is enabled or disabled. If called
   when enabled, then the current limit changes instantly, otherwise the current
   limit configuration changes and the current limit is physically set when the
   regulator is next enabled.

 A regulators current limit can be found by calling::

 	int regulator_get_current_limit(regulator);

 NOTE:
   get_current_limit() will return the current limit whether the regulator
   is enabled or disabled and should not be used to determine regulator current
   load.


 5. Regulator Operating Mode Control & Status (dynamic drivers)
 ==============================================================

 Some consumers can further save system power by changing the operating mode of
 their supply regulator to be more efficient when the consumers operating state
 changes. e.g. consumer driver is idle and subsequently draws less current

 Regulator operating mode can be changed indirectly or directly.

 Indirect operating mode control.
 --------------------------------
 Consumer drivers can request a change in their supply regulator operating mode
 by calling::

 	int regulator_set_load(struct regulator *regulator, int load_uA);

 This will cause the core to recalculate the total load on the regulator (based
 on all its consumers) and change operating mode (if necessary and permitted)
 to best match the current operating load.

 The load_uA value can be determined from the consumer's datasheet. e.g. most
 datasheets have tables showing the maximum current consumed in certain
 situations.

 Most consumers will use indirect operating mode control since they have no
 knowledge of the regulator or whether the regulator is shared with other
 consumers.

 Direct operating mode control.
 ------------------------------

 Bespoke or tightly coupled drivers may want to directly control regulator
 operating mode depending on their operating point. This can be achieved by
 calling::

 	int regulator_set_mode(struct regulator *regulator, unsigned int mode);
 	unsigned int regulator_get_mode(struct regulator *regulator);

 Direct mode will only be used by consumers that *know* about the regulator and
 are not sharing the regulator with other consumers.


 6. Regulator Events
 ===================

 Regulators can notify consumers of external events. Events could be received by
 consumers under regulator stress or failure conditions.

 Consumers can register interest in regulator events by calling::

 	int regulator_register_notifier(struct regulator *regulator,
 					struct notifier_block *nb);

 Consumers can unregister interest by calling::

 	int regulator_unregister_notifier(struct regulator *regulator,
 					  struct notifier_block *nb);

 Regulators use the kernel notifier framework to send event to their interested
 consumers.

 7. Regulator Direct Register Access
 ===================================

 Some kinds of power management hardware or firmware are designed such that
 they need to do low-level hardware access to regulators, with no involvement
 from the kernel. Examples of such devices are:

 - clocksource with a voltage-controlled oscillator and control logic to change
   the supply voltage over I2C to achieve a desired output clock rate
 - thermal management firmware that can issue an arbitrary I2C transaction to
   perform system poweroff during overtemperature conditions

 To set up such a device/firmware, various parameters like I2C address of the
 regulator, addresses of various regulator registers etc. need to be configured
 to it. The regulator framework provides the following helpers for querying
 these details.

 Bus-specific details, like I2C addresses or transfer rates are handled by the
 regmap framework. To get the regulator's regmap (if supported), use::

 	struct regmap *regulator_get_regmap(struct regulator *regulator);

 To obtain the hardware register offset and bitmask for the regulator's voltage
 selector register, use::

 	int regulator_get_hardware_vsel_register(struct regulator *regulator,
 						 unsigned *vsel_reg,
 						 unsigned *vsel_mask);

 To convert a regulator framework voltage selector code (used by
 regulator_list_voltage) to a hardware-specific voltage selector that can be
 directly written to the voltage selector register, use::

 	int regulator_list_hardware_vsel(struct regulator *regulator,
 					 unsigned selector);
	===================================
	Regulator Consumer Driver Interface
	===================================

	This text describes the regulator interface for consumer device drivers.
	Please see overview.txt for a description of the terms used in this text.


	1. Consumer Regulator Access (static & dynamic drivers)
	=======================================================

	A consumer driver can get access to its supply regulator by calling ::

	regulator = regulator_get(dev, "Vcc");

	The consumer passes in its struct device pointer and power supply ID. The core
	then finds the correct regulator by consulting a machine specific lookup table.
	If the lookup is successful then this call will return a pointer to the struct
	regulator that supplies this consumer.

	To release the regulator the consumer driver should call ::

	regulator_put(regulator);

	Consumers can be supplied by more than one regulator e.g. codec consumer with
	analog and digital supplies ::

	digital = regulator_get(dev, "Vcc"); /* digital core */
	analog = regulator_get(dev, "Avdd"); /* analog */

	The regulator access functions regulator_get() and regulator_put() will
	usually be called in your device drivers probe() and remove() respectively.


	2. Regulator Output Enable & Disable (static & dynamic drivers)
	===============================================================


	A consumer can enable its power supply by calling::

	int regulator_enable(regulator);

	NOTE:
	The supply may already be enabled before regulator_enabled() is called.
	This may happen if the consumer shares the regulator or the regulator has been
	previously enabled by bootloader or kernel board initialization code.

	A consumer can determine if a regulator is enabled by calling::

	int regulator_is_enabled(regulator);

	This will return > zero when the regulator is enabled.


	A consumer can disable its supply when no longer needed by calling::

	int regulator_disable(regulator);

	NOTE:
	This may not disable the supply if it's shared with other consumers. The
	regulator will only be disabled when the enabled reference count is zero.

	Finally, a regulator can be forcefully disabled in the case of an emergency::

	int regulator_force_disable(regulator);

	NOTE:
	this will immediately and forcefully shutdown the regulator output. All
	consumers will be powered off.


	3. Regulator Voltage Control & Status (dynamic drivers)
	=======================================================

	Some consumer drivers need to be able to dynamically change their supply
	voltage to match system operating points. e.g. CPUfreq drivers can scale
	voltage along with frequency to save power, SD drivers may need to select the
	correct card voltage, etc.

	Consumers can control their supply voltage by calling::

	int regulator_set_voltage(regulator, min_uV, max_uV);

	Where min_uV and max_uV are the minimum and maximum acceptable voltages in
	microvolts.

	NOTE: this can be called when the regulator is enabled or disabled. If called
	when enabled, then the voltage changes instantly, otherwise the voltage
	configuration changes and the voltage is physically set when the regulator is
	next enabled.

	The regulators configured voltage output can be found by calling::

	int regulator_get_voltage(regulator);

	NOTE:
	get_voltage() will return the configured output voltage whether the
	regulator is enabled or disabled and should NOT be used to determine regulator
	output state. However this can be used in conjunction with is_enabled() to
	determine the regulator physical output voltage.


	4. Regulator Current Limit Control & Status (dynamic drivers)
	=============================================================

	Some consumer drivers need to be able to dynamically change their supply
	current limit to match system operating points. e.g. LCD backlight driver can
	change the current limit to vary the backlight brightness, USB drivers may want
	to set the limit to 500mA when supplying power.

	Consumers can control their supply current limit by calling::

	int regulator_set_current_limit(regulator, min_uA, max_uA);

	Where min_uA and max_uA are the minimum and maximum acceptable current limit in
	microamps.

	NOTE:
	this can be called when the regulator is enabled or disabled. If called
	when enabled, then the current limit changes instantly, otherwise the current
	limit configuration changes and the current limit is physically set when the
	regulator is next enabled.

	A regulators current limit can be found by calling::

	int regulator_get_current_limit(regulator);

	NOTE:
	get_current_limit() will return the current limit whether the regulator
	is enabled or disabled and should not be used to determine regulator current
	load.


	5. Regulator Operating Mode Control & Status (dynamic drivers)
	==============================================================

	Some consumers can further save system power by changing the operating mode of
	their supply regulator to be more efficient when the consumers operating state
	changes. e.g. consumer driver is idle and subsequently draws less current

	Regulator operating mode can be changed indirectly or directly.

	Indirect operating mode control.
	--------------------------------
	Consumer drivers can request a change in their supply regulator operating mode
	by calling::

	int regulator_set_load(struct regulator *regulator, int load_uA);

	This will cause the core to recalculate the total load on the regulator (based
	on all its consumers) and change operating mode (if necessary and permitted)
	to best match the current operating load.

	The load_uA value can be determined from the consumer's datasheet. e.g. most
	datasheets have tables showing the maximum current consumed in certain
	situations.

	Most consumers will use indirect operating mode control since they have no
	knowledge of the regulator or whether the regulator is shared with other
	consumers.

	Direct operating mode control.
	------------------------------

	Bespoke or tightly coupled drivers may want to directly control regulator
	operating mode depending on their operating point. This can be achieved by
	calling::

	int regulator_set_mode(struct regulator *regulator, unsigned int mode);
	unsigned int regulator_get_mode(struct regulator *regulator);

	Direct mode will only be used by consumers that know about the regulator and
	are not sharing the regulator with other consumers.


	6. Regulator Events
	===================

	Regulators can notify consumers of external events. Events could be received by
	consumers under regulator stress or failure conditions.

	Consumers can register interest in regulator events by calling::

	int regulator_register_notifier(struct regulator *regulator,
	struct notifier_block *nb);

	Consumers can unregister interest by calling::

	int regulator_unregister_notifier(struct regulator *regulator,
	struct notifier_block *nb);

	Regulators use the kernel notifier framework to send event to their interested
	consumers.

	7. Regulator Direct Register Access
	===================================

	Some kinds of power management hardware or firmware are designed such that
	they need to do low-level hardware access to regulators, with no involvement
	from the kernel. Examples of such devices are:

	- clocksource with a voltage-controlled oscillator and control logic to change
	the supply voltage over I2C to achieve a desired output clock rate
	- thermal management firmware that can issue an arbitrary I2C transaction to
	perform system poweroff during overtemperature conditions

	To set up such a device/firmware, various parameters like I2C address of the
	regulator, addresses of various regulator registers etc. need to be configured
	to it. The regulator framework provides the following helpers for querying
	these details.

	Bus-specific details, like I2C addresses or transfer rates are handled by the
	regmap framework. To get the regulator's regmap (if supported), use::

	struct regmap regulator_get_regmap(struct regulator regulator);

	To obtain the hardware register offset and bitmask for the regulator's voltage
	selector register, use::

	int regulator_get_hardware_vsel_register(struct regulator *regulator,
	unsigned *vsel_reg,
	unsigned *vsel_mask);

	To convert a regulator framework voltage selector code (used by
	regulator_list_voltage) to a hardware-specific voltage selector that can be
	directly written to the voltage selector register, use::

	int regulator_list_hardware_vsel(struct regulator *regulator,
	unsigned selector);