| # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/thermal/qcom-spmi-adc-tm5.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: Qualcomm's SPMI PMIC ADC Thermal Monitoring |
| maintainers: |
| - Dmitry Baryshkov <dmitry.baryshkov@linaro.org> |
| |
| properties: |
| compatible: |
| enum: |
| - qcom,spmi-adc-tm5 |
| - qcom,spmi-adc-tm5-gen2 |
| - qcom,adc-tm7 # Incomplete / subject to change |
| |
| reg: |
| maxItems: 1 |
| |
| interrupts: |
| maxItems: 1 |
| |
| "#thermal-sensor-cells": |
| const: 1 |
| description: |
| Number of cells required to uniquely identify the thermal sensors. Since |
| we have multiple sensors this is set to 1 |
| |
| "#address-cells": |
| const: 1 |
| |
| "#size-cells": |
| const: 0 |
| |
| qcom,avg-samples: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: Number of samples to be used for measurement. |
| Not applicable for Gen2 ADC_TM peripheral. |
| enum: |
| - 1 |
| - 2 |
| - 4 |
| - 8 |
| - 16 |
| default: 1 |
| |
| qcom,decimation: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: This parameter is used to decrease ADC sampling rate. |
| Quicker measurements can be made by reducing decimation ratio. |
| Not applicable for Gen2 ADC_TM peripheral. |
| enum: |
| - 250 |
| - 420 |
| - 840 |
| default: 840 |
| |
| patternProperties: |
| "^([-a-z0-9]*)@[0-7]$": |
| type: object |
| description: |
| Represent one thermal sensor. |
| |
| properties: |
| reg: |
| description: Specify the sensor channel. There are 8 channels in PMIC5's ADC TM |
| minimum: 0 |
| maximum: 7 |
| |
| io-channels: |
| description: |
| From common IIO binding. Used to pipe PMIC ADC channel to thermal monitor |
| |
| qcom,ratiometric: |
| $ref: /schemas/types.yaml#/definitions/flag |
| description: |
| Channel calibration type. |
| If this property is specified VADC will use the VDD reference |
| (1.875V) and GND for channel calibration. If property is not found, |
| channel will be calibrated with 0V and 1.25V reference channels, |
| also known as absolute calibration. |
| |
| qcom,hw-settle-time-us: |
| description: Time between AMUX getting configured and the ADC starting conversion. |
| enum: [15, 100, 200, 300, 400, 500, 600, 700, 1000, 2000, 4000, 8000, 16000, 32000, 64000, 128000] |
| |
| qcom,pre-scaling: |
| $ref: /schemas/types.yaml#/definitions/uint32-array |
| description: Used for scaling the channel input signal before the |
| signal is fed to VADC. The configuration for this node is to know the |
| pre-determined ratio and use it for post scaling. It is a pair of |
| integers, denoting the numerator and denominator of the fraction by |
| which input signal is multiplied. For example, <1 3> indicates the |
| signal is scaled down to 1/3 of its value before ADC measurement. If |
| property is not found default value depending on chip will be used. |
| items: |
| - const: 1 |
| - enum: [ 1, 3, 4, 6, 20, 8, 10 ] |
| |
| qcom,avg-samples: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: Number of samples to be used for measurement. |
| This property in child node is applicable only for Gen2 ADC_TM peripheral. |
| enum: |
| - 1 |
| - 2 |
| - 4 |
| - 8 |
| - 16 |
| default: 1 |
| |
| qcom,decimation: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: This parameter is used to decrease ADC sampling rate. |
| Quicker measurements can be made by reducing decimation ratio. |
| This property in child node is applicable only for Gen2 ADC_TM peripheral. |
| enum: |
| - 85 |
| - 340 |
| - 1360 |
| default: 1360 |
| |
| required: |
| - reg |
| - io-channels |
| |
| additionalProperties: |
| false |
| |
| allOf: |
| - if: |
| properties: |
| compatible: |
| contains: |
| const: qcom,spmi-adc-tm5 |
| |
| then: |
| patternProperties: |
| "^([-a-z0-9]*)@[0-7]$": |
| properties: |
| qcom,decimation: false |
| qcom,avg-samples: false |
| |
| - if: |
| properties: |
| compatible: |
| contains: |
| const: qcom,spmi-adc-tm5-gen2 |
| |
| then: |
| properties: |
| qcom,avg-samples: false |
| qcom,decimation: false |
| |
| required: |
| - compatible |
| - reg |
| - interrupts |
| - "#address-cells" |
| - "#size-cells" |
| - "#thermal-sensor-cells" |
| |
| additionalProperties: false |
| |
| examples: |
| - | |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| spmi_bus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pm8150b_adc: adc@3100 { |
| reg = <0x3100>; |
| compatible = "qcom,spmi-adc5"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| |
| /* Other properties are omitted */ |
| conn-therm@4f { |
| reg = <ADC5_AMUX_THM3_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| }; |
| |
| pm8150b_adc_tm: adc-tm@3500 { |
| compatible = "qcom,spmi-adc-tm5"; |
| reg = <0x3500>; |
| interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>; |
| #thermal-sensor-cells = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| conn-therm@0 { |
| reg = <0>; |
| io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| }; |
| }; |
| |
| - | |
| #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> |
| #include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| spmi_bus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pmk8350_vadc: adc@3100 { |
| reg = <0x3100>; |
| compatible = "qcom,spmi-adc7"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| |
| /* Other properties are omitted */ |
| xo-therm@44 { |
| reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| |
| conn-therm@147 { |
| reg = <PM8350_ADC7_AMUX_THM4_100K_PU(1)>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| }; |
| |
| pmk8350_adc_tm: adc-tm@3400 { |
| compatible = "qcom,spmi-adc-tm5-gen2"; |
| reg = <0x3400>; |
| interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>; |
| #thermal-sensor-cells = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmk8350-xo-therm@0 { |
| reg = <0>; |
| io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>; |
| qcom,decimation = <340>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| conn-therm@1 { |
| reg = <1>; |
| io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>; |
| qcom,avg-samples = <2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| }; |
| }; |
| ... |
