blob: a9f0336e1f1fd626cca60c57748c1430be64c8f4 [file] [log] [blame]
/*
*
* BRIEF MODULE DESCRIPTION
* 4G Systems MTX-1 board setup.
*
* Copyright 2003, 2008 MontaVista Software Inc.
* Author: MontaVista Software, Inc. <source@mvista.com>
* Bruno Randolf <bruno.randolf@4g-systems.biz>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/pm.h>
#include <asm/reboot.h>
#include <asm/mach-au1x00/au1000.h>
#include <prom.h>
char irq_tab_alchemy[][5] __initdata = {
[0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 00 - AdapterA-Slot0 (top) */
[1] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
[2] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 02 - AdapterB-Slot0 (top) */
[3] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
[4] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 04 - AdapterC-Slot0 (top) */
[5] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
[6] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 06 - AdapterD-Slot0 (top) */
[7] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
};
extern int (*board_pci_idsel)(unsigned int devsel, int assert);
int mtx1_pci_idsel(unsigned int devsel, int assert);
static void mtx1_reset(char *c)
{
/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
au_writel(0x00000000, 0xAE00001C);
}
static void mtx1_power_off(void)
{
printk(KERN_ALERT "It's now safe to remove power\n");
while (1)
asm volatile (".set mips3 ; wait ; .set mips1");
}
void __init board_setup(void)
{
alchemy_gpio2_enable();
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
/* Enable USB power switch */
alchemy_gpio_direction_output(204, 0);
#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
#ifdef CONFIG_PCI
#if defined(__MIPSEB__)
au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
#else
au_writel(0xf, Au1500_PCI_CFG);
#endif
board_pci_idsel = mtx1_pci_idsel;
#endif
/* Initialize sys_pinfunc */
au_writel(SYS_PF_NI2, SYS_PINFUNC);
/* Initialize GPIO */
au_writel(0xFFFFFFFF, SYS_TRIOUTCLR);
alchemy_gpio_direction_output(0, 0); /* Disable M66EN (PCI 66MHz) */
alchemy_gpio_direction_output(3, 1); /* Disable PCI CLKRUN# */
alchemy_gpio_direction_output(1, 1); /* Enable EXT_IO3 */
alchemy_gpio_direction_output(5, 0); /* Disable eth PHY TX_ER */
/* Enable LED and set it to green */
alchemy_gpio_direction_output(211, 1); /* green on */
alchemy_gpio_direction_output(212, 0); /* red off */
pm_power_off = mtx1_power_off;
_machine_halt = mtx1_power_off;
_machine_restart = mtx1_reset;
printk(KERN_INFO "4G Systems MTX-1 Board\n");
}
int
mtx1_pci_idsel(unsigned int devsel, int assert)
{
#define MTX_IDSEL_ONLY_0_AND_3 0
#if MTX_IDSEL_ONLY_0_AND_3
if (devsel != 0 && devsel != 3) {
printk(KERN_ERR "*** not 0 or 3\n");
return 0;
}
#endif
if (assert && devsel != 0)
/* Suppress signal to Cardbus */
gpio_set_value(1, 0); /* set EXT_IO3 OFF */
else
gpio_set_value(1, 1); /* set EXT_IO3 ON */
au_sync_udelay(1);
return 1;
}
static int __init mtx1_init_irq(void)
{
set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
return 0;
}
arch_initcall(mtx1_init_irq);