| * Texas Instruments Keystone Navigator Queue Management SubSystem driver |
| |
| The QMSS (Queue Manager Sub System) found on Keystone SOCs is one of |
| the main hardware sub system which forms the backbone of the Keystone |
| multi-core Navigator. QMSS consist of queue managers, packed-data structure |
| processors(PDSP), linking RAM, descriptor pools and infrastructure |
| Packet DMA. |
| The Queue Manager is a hardware module that is responsible for accelerating |
| management of the packet queues. Packets are queued/de-queued by writing or |
| reading descriptor address to a particular memory mapped location. The PDSPs |
| perform QMSS related functions like accumulation, QoS, or event management. |
| Linking RAM registers are used to link the descriptors which are stored in |
| descriptor RAM. Descriptor RAM is configurable as internal or external memory. |
| The QMSS driver manages the PDSP setups, linking RAM regions, |
| queue pool management (allocation, push, pop and notify) and descriptor |
| pool management. |
| |
| |
| Required properties: |
| - compatible : Must be "ti,keystone-navigator-qmss"; |
| - clocks : phandle to the reference clock for this device. |
| - queue-range : <start number> total range of queue numbers for the device. |
| - linkram0 : <address size> for internal link ram, where size is the total |
| link ram entries. |
| - linkram1 : <address size> for external link ram, where size is the total |
| external link ram entries. If the address is specified as "0" |
| driver will allocate memory. |
| - qmgrs : child node describing the individual queue managers on the |
| SoC. On keystone 1 devices there should be only one node. |
| On keystone 2 devices there can be more than 1 node. |
| -- managed-queues : the actual queues managed by each queue manager |
| instance, specified as <"base queue #" "# of queues">. |
| -- reg : Address and size of the register set for the device. |
| Register regions should be specified in the following |
| order |
| - Queue Peek region. |
| - Queue status RAM. |
| - Queue configuration region. |
| - Descriptor memory setup region. |
| - Queue Management/Queue Proxy region for queue Push. |
| - Queue Management/Queue Proxy region for queue Pop. |
| - queue-pools : child node classifying the queue ranges into pools. |
| Queue ranges are grouped into 3 type of pools: |
| - qpend : pool of qpend(interruptible) queues |
| - general-purpose : pool of general queues, primarly used |
| as free descriptor queues or the |
| transmit DMA queues. |
| - accumulator : pool of queues on PDSP accumulator channel |
| Each range can have the following properties: |
| -- qrange : number of queues to use per queue range, specified as |
| <"base queue #" "# of queues">. |
| -- interrupts : Optional property to specify the interrupt mapping |
| for interruptible queues. The driver additionaly sets |
| the interrupt affinity hint based on the cpu mask. |
| -- qalloc-by-id : Optional property to specify that the queues in this |
| range can only be allocated by queue id. |
| -- accumulator : Accumulator channel specification. Any of the PDSPs in |
| QMSS can be loaded with the accumulator firmware. The |
| accumulator firmware’s job is to poll a select number of |
| queues looking for descriptors that have been pushed |
| into them. Descriptors are popped from the queue and |
| placed in a buffer provided by the host. When the list |
| becomes full or a programmed time period expires, the |
| accumulator triggers an interrupt to the host to read |
| the buffer for descriptor information. This firmware |
| comes in 16, 32, and 48 channel builds. Each of these |
| channels can be configured to monitor 32 contiguous |
| queues. Accumulator channel property is specified as: |
| <pdsp-id, channel, entries, pacing mode, latency> |
| pdsp-id : QMSS PDSP running accumulator firmware |
| on which the channel has to be |
| configured |
| channel : Accumulator channel number |
| entries : Size of the accumulator descriptor list |
| pacing mode : Interrupt pacing mode |
| 0 : None, i.e interrupt on list full only |
| 1 : Time delay since last interrupt |
| 2 : Time delay since first new packet |
| 3 : Time delay since last new packet |
| latency : time to delay the interrupt, specified |
| in microseconds. |
| -- multi-queue : Optional property to specify that the channel has to |
| monitor upto 32 queues starting at the base queue #. |
| - descriptor-regions : child node describing the memory regions for keystone |
| navigator packet DMA descriptors. The memory for |
| descriptors will be allocated by the driver. |
| -- id : region number in QMSS. |
| -- region-spec : specifies the number of descriptors in the |
| region, specified as |
| <"# of descriptors" "descriptor size">. |
| -- link-index : start index, i.e. index of the first |
| descriptor in the region. |
| |
| Optional properties: |
| - dma-coherent : Present if DMA operations are coherent. |
| - pdsps : child node describing the PDSP configuration. |
| -- firmware : firmware to be loaded on the PDSP. |
| -- id : the qmss pdsp that will run the firmware. |
| -- reg : Address and size of the register set for the PDSP. |
| Register regions should be specified in the following |
| order |
| - PDSP internal RAM region. |
| - PDSP control/status region registers. |
| - QMSS interrupt distributor registers. |
| - PDSP command interface region. |
| |
| Example: |
| |
| qmss: qmss@2a40000 { |
| compatible = "ti,keystone-qmss"; |
| dma-coherent; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| clocks = <&chipclk13>; |
| ranges; |
| queue-range = <0 0x4000>; |
| linkram0 = <0x100000 0x8000>; |
| linkram1 = <0x0 0x10000>; |
| |
| qmgrs { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| qmgr0 { |
| managed-queues = <0 0x2000>; |
| reg = <0x2a40000 0x20000>, |
| <0x2a06000 0x400>, |
| <0x2a02000 0x1000>, |
| <0x2a03000 0x1000>, |
| <0x23a80000 0x20000>, |
| <0x2a80000 0x20000>; |
| }; |
| |
| qmgr1 { |
| managed-queues = <0x2000 0x2000>; |
| reg = <0x2a60000 0x20000>, |
| <0x2a06400 0x400>, |
| <0x2a04000 0x1000>, |
| <0x2a05000 0x1000>, |
| <0x23aa0000 0x20000>, |
| <0x2aa0000 0x20000>; |
| }; |
| }; |
| queue-pools { |
| qpend { |
| qpend-0 { |
| qrange = <658 8>; |
| interrupts =<0 40 0xf04 0 41 0xf04 0 42 0xf04 |
| 0 43 0xf04 0 44 0xf04 0 45 0xf04 |
| 0 46 0xf04 0 47 0xf04>; |
| }; |
| qpend-1 { |
| qrange = <8704 16>; |
| interrupts = <0 48 0xf04 0 49 0xf04 0 50 0xf04 |
| 0 51 0xf04 0 52 0xf04 0 53 0xf04 |
| 0 54 0xf04 0 55 0xf04 0 56 0xf04 |
| 0 57 0xf04 0 58 0xf04 0 59 0xf04 |
| 0 60 0xf04 0 61 0xf04 0 62 0xf04 |
| 0 63 0xf04>; |
| qalloc-by-id; |
| }; |
| qpend-2 { |
| qrange = <8720 16>; |
| interrupts = <0 64 0xf04 0 65 0xf04 0 66 0xf04 |
| 0 59 0xf04 0 68 0xf04 0 69 0xf04 |
| 0 70 0xf04 0 71 0xf04 0 72 0xf04 |
| 0 73 0xf04 0 74 0xf04 0 75 0xf04 |
| 0 76 0xf04 0 77 0xf04 0 78 0xf04 |
| 0 79 0xf04>; |
| }; |
| }; |
| general-purpose { |
| gp-0 { |
| qrange = <4000 64>; |
| }; |
| netcp-tx { |
| qrange = <640 9>; |
| qalloc-by-id; |
| }; |
| }; |
| accumulator { |
| acc-0 { |
| qrange = <128 32>; |
| accumulator = <0 36 16 2 50>; |
| interrupts = <0 215 0xf01>; |
| multi-queue; |
| qalloc-by-id; |
| }; |
| acc-1 { |
| qrange = <160 32>; |
| accumulator = <0 37 16 2 50>; |
| interrupts = <0 216 0xf01>; |
| multi-queue; |
| }; |
| acc-2 { |
| qrange = <192 32>; |
| accumulator = <0 38 16 2 50>; |
| interrupts = <0 217 0xf01>; |
| multi-queue; |
| }; |
| acc-3 { |
| qrange = <224 32>; |
| accumulator = <0 39 16 2 50>; |
| interrupts = <0 218 0xf01>; |
| multi-queue; |
| }; |
| }; |
| }; |
| descriptor-regions { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| region-12 { |
| id = <12>; |
| region-spec = <8192 128>; /* num_desc desc_size */ |
| link-index = <0x4000>; |
| }; |
| }; |
| pdsps { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| pdsp0@0x2a10000 { |
| firmware = "keystone/qmss_pdsp_acc48_k2_le_1_0_0_8.fw"; |
| reg = <0x2a10000 0x1000>, |
| <0x2a0f000 0x100>, |
| <0x2a0c000 0x3c8>, |
| <0x2a20000 0x4000>; |
| id = <0>; |
| }; |
| }; |
| }; /* qmss */ |