Documentation/networking/phonet.rst - linux - Git at Google

 .. SPDX-License-Identifier: GPL-2.0
 .. include:: <isonum.txt>

 ============================
 Linux Phonet protocol family
 ============================

 Introduction
 ------------

 Phonet is a packet protocol used by Nokia cellular modems for both IPC
 and RPC. With the Linux Phonet socket family, Linux host processes can
 receive and send messages from/to the modem, or any other external
 device attached to the modem. The modem takes care of routing.

 Phonet packets can be exchanged through various hardware connections
 depending on the device, such as:

   - USB with the CDC Phonet interface,
   - infrared,
   - Bluetooth,
   - an RS232 serial port (with a dedicated "FBUS" line discipline),
   - the SSI bus with some TI OMAP processors.


 Packets format
 --------------

 Phonet packets have a common header as follows::

   struct phonethdr {
     uint8_t  pn_media;  /* Media type (link-layer identifier) */
     uint8_t  pn_rdev;   /* Receiver device ID */
     uint8_t  pn_sdev;   /* Sender device ID */
     uint8_t  pn_res;    /* Resource ID or function */
     uint16_t pn_length; /* Big-endian message byte length (minus 6) */
     uint8_t  pn_robj;   /* Receiver object ID */
     uint8_t  pn_sobj;   /* Sender object ID */
   };

 On Linux, the link-layer header includes the pn_media byte (see below).
 The next 7 bytes are part of the network-layer header.

 The device ID is split: the 6 higher-order bits constitute the device
 address, while the 2 lower-order bits are used for multiplexing, as are
 the 8-bit object identifiers. As such, Phonet can be considered as a
 network layer with 6 bits of address space and 10 bits for transport
 protocol (much like port numbers in IP world).

 The modem always has address number zero. All other device have a their
 own 6-bit address.


 Link layer
 ----------

 Phonet links are always point-to-point links. The link layer header
 consists of a single Phonet media type byte. It uniquely identifies the
 link through which the packet is transmitted, from the modem's
 perspective. Each Phonet network device shall prepend and set the media
 type byte as appropriate. For convenience, a common phonet_header_ops
 link-layer header operations structure is provided. It sets the
 media type according to the network device hardware address.

 Linux Phonet network interfaces support a dedicated link layer packets
 type (ETH_P_PHONET) which is out of the Ethernet type range. They can
 only send and receive Phonet packets.

 The virtual TUN tunnel device driver can also be used for Phonet. This
 requires IFF_TUN mode, _without_ the IFF_NO_PI flag. In this case,
 there is no link-layer header, so there is no Phonet media type byte.

 Note that Phonet interfaces are not allowed to re-order packets, so
 only the (default) Linux FIFO qdisc should be used with them.


 Network layer
 -------------

 The Phonet socket address family maps the Phonet packet header::

   struct sockaddr_pn {
     sa_family_t spn_family;    /* AF_PHONET */
     uint8_t     spn_obj;       /* Object ID */
     uint8_t     spn_dev;       /* Device ID */
     uint8_t     spn_resource;  /* Resource or function */
     uint8_t     spn_zero[...]; /* Padding */
   };

 The resource field is only used when sending and receiving;
 It is ignored by bind() and getsockname().


 Low-level datagram protocol
 ---------------------------

 Applications can send Phonet messages using the Phonet datagram socket
 protocol from the PF_PHONET family. Each socket is bound to one of the
 2^10 object IDs available, and can send and receive packets with any
 other peer.

 ::

   struct sockaddr_pn addr = { .spn_family = AF_PHONET, };
   ssize_t len;
   socklen_t addrlen = sizeof(addr);
   int fd;

   fd = socket(PF_PHONET, SOCK_DGRAM, 0);
   bind(fd, (struct sockaddr *)&addr, sizeof(addr));
   /* ... */

   sendto(fd, msg, msglen, 0, (struct sockaddr *)&addr, sizeof(addr));
   len = recvfrom(fd, buf, sizeof(buf), 0,
 		 (struct sockaddr *)&addr, &addrlen);

 This protocol follows the SOCK_DGRAM connection-less semantics.
 However, connect() and getpeername() are not supported, as they did
 not seem useful with Phonet usages (could be added easily).


 Resource subscription
 ---------------------

 A Phonet datagram socket can be subscribed to any number of 8-bits
 Phonet resources, as follow::

   uint32_t res = 0xXX;
   ioctl(fd, SIOCPNADDRESOURCE, &res);

 Subscription is similarly cancelled using the SIOCPNDELRESOURCE I/O
 control request, or when the socket is closed.

 Note that no more than one socket can be subcribed to any given
 resource at a time. If not, ioctl() will return EBUSY.


 Phonet Pipe protocol
 --------------------

 The Phonet Pipe protocol is a simple sequenced packets protocol
 with end-to-end congestion control. It uses the passive listening
 socket paradigm. The listening socket is bound to an unique free object
 ID. Each listening socket can handle up to 255 simultaneous
 connections, one per accept()'d socket.

 ::

   int lfd, cfd;

   lfd = socket(PF_PHONET, SOCK_SEQPACKET, PN_PROTO_PIPE);
   listen (lfd, INT_MAX);

   /* ... */
   cfd = accept(lfd, NULL, NULL);
   for (;;)
   {
     char buf[...];
     ssize_t len = read(cfd, buf, sizeof(buf));

     /* ... */

     write(cfd, msg, msglen);
   }

 Connections are traditionally established between two endpoints by a
 "third party" application. This means that both endpoints are passive.


 As of Linux kernel version 2.6.39, it is also possible to connect
 two endpoints directly, using connect() on the active side. This is
 intended to support the newer Nokia Wireless Modem API, as found in
 e.g. the Nokia Slim Modem in the ST-Ericsson U8500 platform::

   struct sockaddr_spn spn;
   int fd;

   fd = socket(PF_PHONET, SOCK_SEQPACKET, PN_PROTO_PIPE);
   memset(&spn, 0, sizeof(spn));
   spn.spn_family = AF_PHONET;
   spn.spn_obj = ...;
   spn.spn_dev = ...;
   spn.spn_resource = 0xD9;
   connect(fd, (struct sockaddr *)&spn, sizeof(spn));
   /* normal I/O here ... */
   close(fd);


 .. Warning:

    When polling a connected pipe socket for writability, there is an
    intrinsic race condition whereby writability might be lost between the
    polling and the writing system calls. In this case, the socket will
    block until write becomes possible again, unless non-blocking mode
    is enabled.


 The pipe protocol provides two socket options at the SOL_PNPIPE level:

   PNPIPE_ENCAP accepts one integer value (int) of:

     PNPIPE_ENCAP_NONE:
       The socket operates normally (default).

     PNPIPE_ENCAP_IP:
       The socket is used as a backend for a virtual IP
       interface. This requires CAP_NET_ADMIN capability. GPRS data
       support on Nokia modems can use this. Note that the socket cannot
       be reliably poll()'d or read() from while in this mode.

   PNPIPE_IFINDEX
       is a read-only integer value. It contains the
       interface index of the network interface created by PNPIPE_ENCAP,
       or zero if encapsulation is off.

   PNPIPE_HANDLE
       is a read-only integer value. It contains the underlying
       identifier ("pipe handle") of the pipe. This is only defined for
       socket descriptors that are already connected or being connected.


 Authors
 -------

 Linux Phonet was initially written by Sakari Ailus.

 Other contributors include Mikä Liljeberg, Andras Domokos,
 Carlos Chinea and Rémi Denis-Courmont.

 Copyright |copy| 2008 Nokia Corporation.
	.. SPDX-License-Identifier: GPL-2.0
	.. include:: <isonum.txt>

	============================
	Linux Phonet protocol family
	============================

	Introduction
	------------

	Phonet is a packet protocol used by Nokia cellular modems for both IPC
	and RPC. With the Linux Phonet socket family, Linux host processes can
	receive and send messages from/to the modem, or any other external
	device attached to the modem. The modem takes care of routing.

	Phonet packets can be exchanged through various hardware connections
	depending on the device, such as:

	- USB with the CDC Phonet interface,
	- infrared,
	- Bluetooth,
	- an RS232 serial port (with a dedicated "FBUS" line discipline),
	- the SSI bus with some TI OMAP processors.


	Packets format
	--------------

	Phonet packets have a common header as follows::

	struct phonethdr {
	uint8_t pn_media; /* Media type (link-layer identifier) */
	uint8_t pn_rdev; /* Receiver device ID */
	uint8_t pn_sdev; /* Sender device ID */
	uint8_t pn_res; /* Resource ID or function */
	uint16_t pn_length; /* Big-endian message byte length (minus 6) */
	uint8_t pn_robj; /* Receiver object ID */
	uint8_t pn_sobj; /* Sender object ID */
	};

	On Linux, the link-layer header includes the pn_media byte (see below).
	The next 7 bytes are part of the network-layer header.

	The device ID is split: the 6 higher-order bits constitute the device
	address, while the 2 lower-order bits are used for multiplexing, as are
	the 8-bit object identifiers. As such, Phonet can be considered as a
	network layer with 6 bits of address space and 10 bits for transport
	protocol (much like port numbers in IP world).

	The modem always has address number zero. All other device have a their
	own 6-bit address.


	Link layer
	----------

	Phonet links are always point-to-point links. The link layer header
	consists of a single Phonet media type byte. It uniquely identifies the
	link through which the packet is transmitted, from the modem's
	perspective. Each Phonet network device shall prepend and set the media
	type byte as appropriate. For convenience, a common phonet_header_ops
	link-layer header operations structure is provided. It sets the
	media type according to the network device hardware address.

	Linux Phonet network interfaces support a dedicated link layer packets
	type (ETH_P_PHONET) which is out of the Ethernet type range. They can
	only send and receive Phonet packets.

	The virtual TUN tunnel device driver can also be used for Phonet. This
	requires IFF_TUN mode, _without_ the IFF_NO_PI flag. In this case,
	there is no link-layer header, so there is no Phonet media type byte.

	Note that Phonet interfaces are not allowed to re-order packets, so
	only the (default) Linux FIFO qdisc should be used with them.


	Network layer
	-------------

	The Phonet socket address family maps the Phonet packet header::

	struct sockaddr_pn {
	sa_family_t spn_family; /* AF_PHONET */
	uint8_t spn_obj; /* Object ID */
	uint8_t spn_dev; /* Device ID */
	uint8_t spn_resource; /* Resource or function */
	uint8_t spn_zero[...]; /* Padding */
	};

	The resource field is only used when sending and receiving;
	It is ignored by bind() and getsockname().


	Low-level datagram protocol
	---------------------------

	Applications can send Phonet messages using the Phonet datagram socket
	protocol from the PF_PHONET family. Each socket is bound to one of the
	2^10 object IDs available, and can send and receive packets with any
	other peer.

	::

	struct sockaddr_pn addr = { .spn_family = AF_PHONET, };
	ssize_t len;
	socklen_t addrlen = sizeof(addr);
	int fd;

	fd = socket(PF_PHONET, SOCK_DGRAM, 0);
	bind(fd, (struct sockaddr *)&addr, sizeof(addr));
	/* ... */

	sendto(fd, msg, msglen, 0, (struct sockaddr *)&addr, sizeof(addr));
	len = recvfrom(fd, buf, sizeof(buf), 0,
	(struct sockaddr *)&addr, &addrlen);

	This protocol follows the SOCK_DGRAM connection-less semantics.
	However, connect() and getpeername() are not supported, as they did
	not seem useful with Phonet usages (could be added easily).


	Resource subscription
	---------------------

	A Phonet datagram socket can be subscribed to any number of 8-bits
	Phonet resources, as follow::

	uint32_t res = 0xXX;
	ioctl(fd, SIOCPNADDRESOURCE, &res);

	Subscription is similarly cancelled using the SIOCPNDELRESOURCE I/O
	control request, or when the socket is closed.

	Note that no more than one socket can be subcribed to any given
	resource at a time. If not, ioctl() will return EBUSY.


	Phonet Pipe protocol
	--------------------

	The Phonet Pipe protocol is a simple sequenced packets protocol
	with end-to-end congestion control. It uses the passive listening
	socket paradigm. The listening socket is bound to an unique free object
	ID. Each listening socket can handle up to 255 simultaneous
	connections, one per accept()'d socket.

	::

	int lfd, cfd;

	lfd = socket(PF_PHONET, SOCK_SEQPACKET, PN_PROTO_PIPE);
	listen (lfd, INT_MAX);

	/* ... */
	cfd = accept(lfd, NULL, NULL);
	for (;;)
	{
	char buf[...];
	ssize_t len = read(cfd, buf, sizeof(buf));

	/* ... */

	write(cfd, msg, msglen);
	}

	Connections are traditionally established between two endpoints by a
	"third party" application. This means that both endpoints are passive.


	As of Linux kernel version 2.6.39, it is also possible to connect
	two endpoints directly, using connect() on the active side. This is
	intended to support the newer Nokia Wireless Modem API, as found in
	e.g. the Nokia Slim Modem in the ST-Ericsson U8500 platform::

	struct sockaddr_spn spn;
	int fd;

	fd = socket(PF_PHONET, SOCK_SEQPACKET, PN_PROTO_PIPE);
	memset(&spn, 0, sizeof(spn));
	spn.spn_family = AF_PHONET;
	spn.spn_obj = ...;
	spn.spn_dev = ...;
	spn.spn_resource = 0xD9;
	connect(fd, (struct sockaddr *)&spn, sizeof(spn));
	/* normal I/O here ... */
	close(fd);


	.. Warning:

	When polling a connected pipe socket for writability, there is an
	intrinsic race condition whereby writability might be lost between the
	polling and the writing system calls. In this case, the socket will
	block until write becomes possible again, unless non-blocking mode
	is enabled.


	The pipe protocol provides two socket options at the SOL_PNPIPE level:

	PNPIPE_ENCAP accepts one integer value (int) of:

	PNPIPE_ENCAP_NONE:
	The socket operates normally (default).

	PNPIPE_ENCAP_IP:
	The socket is used as a backend for a virtual IP
	interface. This requires CAP_NET_ADMIN capability. GPRS data
	support on Nokia modems can use this. Note that the socket cannot
	be reliably poll()'d or read() from while in this mode.

	PNPIPE_IFINDEX
	is a read-only integer value. It contains the
	interface index of the network interface created by PNPIPE_ENCAP,
	or zero if encapsulation is off.

	PNPIPE_HANDLE
	is a read-only integer value. It contains the underlying
	identifier ("pipe handle") of the pipe. This is only defined for
	socket descriptors that are already connected or being connected.


	Authors
	-------

	Linux Phonet was initially written by Sakari Ailus.

	Other contributors include Mikä Liljeberg, Andras Domokos,
	Carlos Chinea and Rémi Denis-Courmont.

	Copyright \|copy\| 2008 Nokia Corporation.