| // SPDX-License-Identifier: GPL-2.0 OR MIT |
| /* |
| * MTK ECC controller driver. |
| * Copyright (C) 2016 MediaTek Inc. |
| * Authors: Xiaolei Li <xiaolei.li@mediatek.com> |
| * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> |
| */ |
| |
| #include <linux/platform_device.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/interrupt.h> |
| #include <linux/clk.h> |
| #include <linux/module.h> |
| #include <linux/iopoll.h> |
| #include <linux/of.h> |
| #include <linux/of_platform.h> |
| #include <linux/mutex.h> |
| |
| #include "mtk_ecc.h" |
| |
| #define ECC_IDLE_MASK BIT(0) |
| #define ECC_IRQ_EN BIT(0) |
| #define ECC_PG_IRQ_SEL BIT(1) |
| #define ECC_OP_ENABLE (1) |
| #define ECC_OP_DISABLE (0) |
| |
| #define ECC_ENCCON (0x00) |
| #define ECC_ENCCNFG (0x04) |
| #define ECC_MS_SHIFT (16) |
| #define ECC_ENCDIADDR (0x08) |
| #define ECC_ENCIDLE (0x0C) |
| #define ECC_DECCON (0x100) |
| #define ECC_DECCNFG (0x104) |
| #define DEC_EMPTY_EN BIT(31) |
| #define DEC_CNFG_CORRECT (0x3 << 12) |
| #define ECC_DECIDLE (0x10C) |
| #define ECC_DECENUM0 (0x114) |
| |
| #define ECC_TIMEOUT (500000) |
| |
| #define ECC_IDLE_REG(op) ((op) == ECC_ENCODE ? ECC_ENCIDLE : ECC_DECIDLE) |
| #define ECC_CTL_REG(op) ((op) == ECC_ENCODE ? ECC_ENCCON : ECC_DECCON) |
| |
| struct mtk_ecc_caps { |
| u32 err_mask; |
| const u8 *ecc_strength; |
| const u32 *ecc_regs; |
| u8 num_ecc_strength; |
| u8 ecc_mode_shift; |
| u32 parity_bits; |
| int pg_irq_sel; |
| }; |
| |
| struct mtk_ecc { |
| struct device *dev; |
| const struct mtk_ecc_caps *caps; |
| void __iomem *regs; |
| struct clk *clk; |
| |
| struct completion done; |
| struct mutex lock; |
| u32 sectors; |
| |
| u8 *eccdata; |
| }; |
| |
| /* ecc strength that each IP supports */ |
| static const u8 ecc_strength_mt2701[] = { |
| 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, |
| 40, 44, 48, 52, 56, 60 |
| }; |
| |
| static const u8 ecc_strength_mt2712[] = { |
| 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, |
| 40, 44, 48, 52, 56, 60, 68, 72, 80 |
| }; |
| |
| static const u8 ecc_strength_mt7622[] = { |
| 4, 6, 8, 10, 12, 14, 16 |
| }; |
| |
| enum mtk_ecc_regs { |
| ECC_ENCPAR00, |
| ECC_ENCIRQ_EN, |
| ECC_ENCIRQ_STA, |
| ECC_DECDONE, |
| ECC_DECIRQ_EN, |
| ECC_DECIRQ_STA, |
| }; |
| |
| static int mt2701_ecc_regs[] = { |
| [ECC_ENCPAR00] = 0x10, |
| [ECC_ENCIRQ_EN] = 0x80, |
| [ECC_ENCIRQ_STA] = 0x84, |
| [ECC_DECDONE] = 0x124, |
| [ECC_DECIRQ_EN] = 0x200, |
| [ECC_DECIRQ_STA] = 0x204, |
| }; |
| |
| static int mt2712_ecc_regs[] = { |
| [ECC_ENCPAR00] = 0x300, |
| [ECC_ENCIRQ_EN] = 0x80, |
| [ECC_ENCIRQ_STA] = 0x84, |
| [ECC_DECDONE] = 0x124, |
| [ECC_DECIRQ_EN] = 0x200, |
| [ECC_DECIRQ_STA] = 0x204, |
| }; |
| |
| static int mt7622_ecc_regs[] = { |
| [ECC_ENCPAR00] = 0x10, |
| [ECC_ENCIRQ_EN] = 0x30, |
| [ECC_ENCIRQ_STA] = 0x34, |
| [ECC_DECDONE] = 0x11c, |
| [ECC_DECIRQ_EN] = 0x140, |
| [ECC_DECIRQ_STA] = 0x144, |
| }; |
| |
| static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc, |
| enum mtk_ecc_operation op) |
| { |
| struct device *dev = ecc->dev; |
| u32 val; |
| int ret; |
| |
| ret = readl_poll_timeout_atomic(ecc->regs + ECC_IDLE_REG(op), val, |
| val & ECC_IDLE_MASK, |
| 10, ECC_TIMEOUT); |
| if (ret) |
| dev_warn(dev, "%s NOT idle\n", |
| op == ECC_ENCODE ? "encoder" : "decoder"); |
| } |
| |
| static irqreturn_t mtk_ecc_irq(int irq, void *id) |
| { |
| struct mtk_ecc *ecc = id; |
| u32 dec, enc; |
| |
| dec = readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_STA]) |
| & ECC_IRQ_EN; |
| if (dec) { |
| dec = readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECDONE]); |
| if (dec & ecc->sectors) { |
| /* |
| * Clear decode IRQ status once again to ensure that |
| * there will be no extra IRQ. |
| */ |
| readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_STA]); |
| ecc->sectors = 0; |
| complete(&ecc->done); |
| } else { |
| return IRQ_HANDLED; |
| } |
| } else { |
| enc = readl(ecc->regs + ecc->caps->ecc_regs[ECC_ENCIRQ_STA]) |
| & ECC_IRQ_EN; |
| if (enc) |
| complete(&ecc->done); |
| else |
| return IRQ_NONE; |
| } |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config) |
| { |
| u32 ecc_bit, dec_sz, enc_sz; |
| u32 reg, i; |
| |
| for (i = 0; i < ecc->caps->num_ecc_strength; i++) { |
| if (ecc->caps->ecc_strength[i] == config->strength) |
| break; |
| } |
| |
| if (i == ecc->caps->num_ecc_strength) { |
| dev_err(ecc->dev, "invalid ecc strength %d\n", |
| config->strength); |
| return -EINVAL; |
| } |
| |
| ecc_bit = i; |
| |
| if (config->op == ECC_ENCODE) { |
| /* configure ECC encoder (in bits) */ |
| enc_sz = config->len << 3; |
| |
| reg = ecc_bit | (config->mode << ecc->caps->ecc_mode_shift); |
| reg |= (enc_sz << ECC_MS_SHIFT); |
| writel(reg, ecc->regs + ECC_ENCCNFG); |
| |
| if (config->mode != ECC_NFI_MODE) |
| writel(lower_32_bits(config->addr), |
| ecc->regs + ECC_ENCDIADDR); |
| |
| } else { |
| /* configure ECC decoder (in bits) */ |
| dec_sz = (config->len << 3) + |
| config->strength * ecc->caps->parity_bits; |
| |
| reg = ecc_bit | (config->mode << ecc->caps->ecc_mode_shift); |
| reg |= (dec_sz << ECC_MS_SHIFT) | DEC_CNFG_CORRECT; |
| reg |= DEC_EMPTY_EN; |
| writel(reg, ecc->regs + ECC_DECCNFG); |
| |
| if (config->sectors) |
| ecc->sectors = 1 << (config->sectors - 1); |
| } |
| |
| return 0; |
| } |
| |
| void mtk_ecc_get_stats(struct mtk_ecc *ecc, struct mtk_ecc_stats *stats, |
| int sectors) |
| { |
| u32 offset, i, err; |
| u32 bitflips = 0; |
| |
| stats->corrected = 0; |
| stats->failed = 0; |
| |
| for (i = 0; i < sectors; i++) { |
| offset = (i >> 2) << 2; |
| err = readl(ecc->regs + ECC_DECENUM0 + offset); |
| err = err >> ((i % 4) * 8); |
| err &= ecc->caps->err_mask; |
| if (err == ecc->caps->err_mask) { |
| /* uncorrectable errors */ |
| stats->failed++; |
| continue; |
| } |
| |
| stats->corrected += err; |
| bitflips = max_t(u32, bitflips, err); |
| } |
| |
| stats->bitflips = bitflips; |
| } |
| EXPORT_SYMBOL(mtk_ecc_get_stats); |
| |
| void mtk_ecc_release(struct mtk_ecc *ecc) |
| { |
| clk_disable_unprepare(ecc->clk); |
| put_device(ecc->dev); |
| } |
| EXPORT_SYMBOL(mtk_ecc_release); |
| |
| static void mtk_ecc_hw_init(struct mtk_ecc *ecc) |
| { |
| mtk_ecc_wait_idle(ecc, ECC_ENCODE); |
| writew(ECC_OP_DISABLE, ecc->regs + ECC_ENCCON); |
| |
| mtk_ecc_wait_idle(ecc, ECC_DECODE); |
| writel(ECC_OP_DISABLE, ecc->regs + ECC_DECCON); |
| } |
| |
| static struct mtk_ecc *mtk_ecc_get(struct device_node *np) |
| { |
| struct platform_device *pdev; |
| struct mtk_ecc *ecc; |
| |
| pdev = of_find_device_by_node(np); |
| if (!pdev) |
| return ERR_PTR(-EPROBE_DEFER); |
| |
| ecc = platform_get_drvdata(pdev); |
| if (!ecc) { |
| put_device(&pdev->dev); |
| return ERR_PTR(-EPROBE_DEFER); |
| } |
| |
| clk_prepare_enable(ecc->clk); |
| mtk_ecc_hw_init(ecc); |
| |
| return ecc; |
| } |
| |
| struct mtk_ecc *of_mtk_ecc_get(struct device_node *of_node) |
| { |
| struct mtk_ecc *ecc = NULL; |
| struct device_node *np; |
| |
| np = of_parse_phandle(of_node, "ecc-engine", 0); |
| if (np) { |
| ecc = mtk_ecc_get(np); |
| of_node_put(np); |
| } |
| |
| return ecc; |
| } |
| EXPORT_SYMBOL(of_mtk_ecc_get); |
| |
| int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config) |
| { |
| enum mtk_ecc_operation op = config->op; |
| u16 reg_val; |
| int ret; |
| |
| ret = mutex_lock_interruptible(&ecc->lock); |
| if (ret) { |
| dev_err(ecc->dev, "interrupted when attempting to lock\n"); |
| return ret; |
| } |
| |
| mtk_ecc_wait_idle(ecc, op); |
| |
| ret = mtk_ecc_config(ecc, config); |
| if (ret) { |
| mutex_unlock(&ecc->lock); |
| return ret; |
| } |
| |
| if (config->mode != ECC_NFI_MODE || op != ECC_ENCODE) { |
| init_completion(&ecc->done); |
| reg_val = ECC_IRQ_EN; |
| /* |
| * For ECC_NFI_MODE, if ecc->caps->pg_irq_sel is 1, then it |
| * means this chip can only generate one ecc irq during page |
| * read / write. If is 0, generate one ecc irq each ecc step. |
| */ |
| if (ecc->caps->pg_irq_sel && config->mode == ECC_NFI_MODE) |
| reg_val |= ECC_PG_IRQ_SEL; |
| if (op == ECC_ENCODE) |
| writew(reg_val, ecc->regs + |
| ecc->caps->ecc_regs[ECC_ENCIRQ_EN]); |
| else |
| writew(reg_val, ecc->regs + |
| ecc->caps->ecc_regs[ECC_DECIRQ_EN]); |
| } |
| |
| writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op)); |
| |
| return 0; |
| } |
| EXPORT_SYMBOL(mtk_ecc_enable); |
| |
| void mtk_ecc_disable(struct mtk_ecc *ecc) |
| { |
| enum mtk_ecc_operation op = ECC_ENCODE; |
| |
| /* find out the running operation */ |
| if (readw(ecc->regs + ECC_CTL_REG(op)) != ECC_OP_ENABLE) |
| op = ECC_DECODE; |
| |
| /* disable it */ |
| mtk_ecc_wait_idle(ecc, op); |
| if (op == ECC_DECODE) { |
| /* |
| * Clear decode IRQ status in case there is a timeout to wait |
| * decode IRQ. |
| */ |
| readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECDONE]); |
| writew(0, ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_EN]); |
| } else { |
| writew(0, ecc->regs + ecc->caps->ecc_regs[ECC_ENCIRQ_EN]); |
| } |
| |
| writew(ECC_OP_DISABLE, ecc->regs + ECC_CTL_REG(op)); |
| |
| mutex_unlock(&ecc->lock); |
| } |
| EXPORT_SYMBOL(mtk_ecc_disable); |
| |
| int mtk_ecc_wait_done(struct mtk_ecc *ecc, enum mtk_ecc_operation op) |
| { |
| int ret; |
| |
| ret = wait_for_completion_timeout(&ecc->done, msecs_to_jiffies(500)); |
| if (!ret) { |
| dev_err(ecc->dev, "%s timeout - interrupt did not arrive)\n", |
| (op == ECC_ENCODE) ? "encoder" : "decoder"); |
| return -ETIMEDOUT; |
| } |
| |
| return 0; |
| } |
| EXPORT_SYMBOL(mtk_ecc_wait_done); |
| |
| int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config, |
| u8 *data, u32 bytes) |
| { |
| dma_addr_t addr; |
| u32 len; |
| int ret; |
| |
| addr = dma_map_single(ecc->dev, data, bytes, DMA_TO_DEVICE); |
| ret = dma_mapping_error(ecc->dev, addr); |
| if (ret) { |
| dev_err(ecc->dev, "dma mapping error\n"); |
| return -EINVAL; |
| } |
| |
| config->op = ECC_ENCODE; |
| config->addr = addr; |
| ret = mtk_ecc_enable(ecc, config); |
| if (ret) { |
| dma_unmap_single(ecc->dev, addr, bytes, DMA_TO_DEVICE); |
| return ret; |
| } |
| |
| ret = mtk_ecc_wait_done(ecc, ECC_ENCODE); |
| if (ret) |
| goto timeout; |
| |
| mtk_ecc_wait_idle(ecc, ECC_ENCODE); |
| |
| /* Program ECC bytes to OOB: per sector oob = FDM + ECC + SPARE */ |
| len = (config->strength * ecc->caps->parity_bits + 7) >> 3; |
| |
| /* write the parity bytes generated by the ECC back to temp buffer */ |
| __ioread32_copy(ecc->eccdata, |
| ecc->regs + ecc->caps->ecc_regs[ECC_ENCPAR00], |
| round_up(len, 4)); |
| |
| /* copy into possibly unaligned OOB region with actual length */ |
| memcpy(data + bytes, ecc->eccdata, len); |
| timeout: |
| |
| dma_unmap_single(ecc->dev, addr, bytes, DMA_TO_DEVICE); |
| mtk_ecc_disable(ecc); |
| |
| return ret; |
| } |
| EXPORT_SYMBOL(mtk_ecc_encode); |
| |
| void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p) |
| { |
| const u8 *ecc_strength = ecc->caps->ecc_strength; |
| int i; |
| |
| for (i = 0; i < ecc->caps->num_ecc_strength; i++) { |
| if (*p <= ecc_strength[i]) { |
| if (!i) |
| *p = ecc_strength[i]; |
| else if (*p != ecc_strength[i]) |
| *p = ecc_strength[i - 1]; |
| return; |
| } |
| } |
| |
| *p = ecc_strength[ecc->caps->num_ecc_strength - 1]; |
| } |
| EXPORT_SYMBOL(mtk_ecc_adjust_strength); |
| |
| unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc) |
| { |
| return ecc->caps->parity_bits; |
| } |
| EXPORT_SYMBOL(mtk_ecc_get_parity_bits); |
| |
| static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = { |
| .err_mask = 0x3f, |
| .ecc_strength = ecc_strength_mt2701, |
| .ecc_regs = mt2701_ecc_regs, |
| .num_ecc_strength = 20, |
| .ecc_mode_shift = 5, |
| .parity_bits = 14, |
| .pg_irq_sel = 0, |
| }; |
| |
| static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = { |
| .err_mask = 0x7f, |
| .ecc_strength = ecc_strength_mt2712, |
| .ecc_regs = mt2712_ecc_regs, |
| .num_ecc_strength = 23, |
| .ecc_mode_shift = 5, |
| .parity_bits = 14, |
| .pg_irq_sel = 1, |
| }; |
| |
| static const struct mtk_ecc_caps mtk_ecc_caps_mt7622 = { |
| .err_mask = 0x3f, |
| .ecc_strength = ecc_strength_mt7622, |
| .ecc_regs = mt7622_ecc_regs, |
| .num_ecc_strength = 7, |
| .ecc_mode_shift = 4, |
| .parity_bits = 13, |
| .pg_irq_sel = 0, |
| }; |
| |
| static const struct of_device_id mtk_ecc_dt_match[] = { |
| { |
| .compatible = "mediatek,mt2701-ecc", |
| .data = &mtk_ecc_caps_mt2701, |
| }, { |
| .compatible = "mediatek,mt2712-ecc", |
| .data = &mtk_ecc_caps_mt2712, |
| }, { |
| .compatible = "mediatek,mt7622-ecc", |
| .data = &mtk_ecc_caps_mt7622, |
| }, |
| {}, |
| }; |
| |
| static int mtk_ecc_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct mtk_ecc *ecc; |
| u32 max_eccdata_size; |
| int irq, ret; |
| |
| ecc = devm_kzalloc(dev, sizeof(*ecc), GFP_KERNEL); |
| if (!ecc) |
| return -ENOMEM; |
| |
| ecc->caps = of_device_get_match_data(dev); |
| |
| max_eccdata_size = ecc->caps->num_ecc_strength - 1; |
| max_eccdata_size = ecc->caps->ecc_strength[max_eccdata_size]; |
| max_eccdata_size = (max_eccdata_size * ecc->caps->parity_bits + 7) >> 3; |
| max_eccdata_size = round_up(max_eccdata_size, 4); |
| ecc->eccdata = devm_kzalloc(dev, max_eccdata_size, GFP_KERNEL); |
| if (!ecc->eccdata) |
| return -ENOMEM; |
| |
| ecc->regs = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(ecc->regs)) |
| return PTR_ERR(ecc->regs); |
| |
| ecc->clk = devm_clk_get(dev, NULL); |
| if (IS_ERR(ecc->clk)) { |
| dev_err(dev, "failed to get clock: %ld\n", PTR_ERR(ecc->clk)); |
| return PTR_ERR(ecc->clk); |
| } |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) |
| return irq; |
| |
| ret = dma_set_mask(dev, DMA_BIT_MASK(32)); |
| if (ret) { |
| dev_err(dev, "failed to set DMA mask\n"); |
| return ret; |
| } |
| |
| ret = devm_request_irq(dev, irq, mtk_ecc_irq, 0x0, "mtk-ecc", ecc); |
| if (ret) { |
| dev_err(dev, "failed to request irq\n"); |
| return -EINVAL; |
| } |
| |
| ecc->dev = dev; |
| mutex_init(&ecc->lock); |
| platform_set_drvdata(pdev, ecc); |
| dev_info(dev, "probed\n"); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int mtk_ecc_suspend(struct device *dev) |
| { |
| struct mtk_ecc *ecc = dev_get_drvdata(dev); |
| |
| clk_disable_unprepare(ecc->clk); |
| |
| return 0; |
| } |
| |
| static int mtk_ecc_resume(struct device *dev) |
| { |
| struct mtk_ecc *ecc = dev_get_drvdata(dev); |
| int ret; |
| |
| ret = clk_prepare_enable(ecc->clk); |
| if (ret) { |
| dev_err(dev, "failed to enable clk\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static SIMPLE_DEV_PM_OPS(mtk_ecc_pm_ops, mtk_ecc_suspend, mtk_ecc_resume); |
| #endif |
| |
| MODULE_DEVICE_TABLE(of, mtk_ecc_dt_match); |
| |
| static struct platform_driver mtk_ecc_driver = { |
| .probe = mtk_ecc_probe, |
| .driver = { |
| .name = "mtk-ecc", |
| .of_match_table = of_match_ptr(mtk_ecc_dt_match), |
| #ifdef CONFIG_PM_SLEEP |
| .pm = &mtk_ecc_pm_ops, |
| #endif |
| }, |
| }; |
| |
| module_platform_driver(mtk_ecc_driver); |
| |
| MODULE_AUTHOR("Xiaolei Li <xiaolei.li@mediatek.com>"); |
| MODULE_DESCRIPTION("MTK Nand ECC Driver"); |
| MODULE_LICENSE("Dual MIT/GPL"); |