| /* |
| * Generic GPIO driver for logic cells found in the Nomadik SoC |
| * |
| * Copyright (C) 2008,2009 STMicroelectronics |
| * Copyright (C) 2009 Alessandro Rubini <rubini@unipv.it> |
| * Rewritten based on work by Prafulla WADASKAR <prafulla.wadaskar@st.com> |
| * Copyright (C) 2011 Linus Walleij <linus.walleij@linaro.org> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/device.h> |
| #include <linux/platform_device.h> |
| #include <linux/io.h> |
| #include <linux/clk.h> |
| #include <linux/err.h> |
| #include <linux/gpio.h> |
| #include <linux/spinlock.h> |
| #include <linux/interrupt.h> |
| #include <linux/irq.h> |
| #include <linux/irqdomain.h> |
| #include <linux/slab.h> |
| #include <linux/of_device.h> |
| #include <linux/pinctrl/pinctrl.h> |
| #include <linux/pinctrl/pinmux.h> |
| #include <linux/pinctrl/pinconf.h> |
| /* Since we request GPIOs from ourself */ |
| #include <linux/pinctrl/consumer.h> |
| |
| #include <asm/mach/irq.h> |
| |
| #include <plat/pincfg.h> |
| #include <plat/gpio-nomadik.h> |
| |
| #include "pinctrl-nomadik.h" |
| |
| /* |
| * The GPIO module in the Nomadik family of Systems-on-Chip is an |
| * AMBA device, managing 32 pins and alternate functions. The logic block |
| * is currently used in the Nomadik and ux500. |
| * |
| * Symbols in this file are called "nmk_gpio" for "nomadik gpio" |
| */ |
| |
| #define NMK_GPIO_PER_CHIP 32 |
| |
| struct nmk_gpio_chip { |
| struct gpio_chip chip; |
| struct irq_domain *domain; |
| void __iomem *addr; |
| struct clk *clk; |
| unsigned int bank; |
| unsigned int parent_irq; |
| int secondary_parent_irq; |
| u32 (*get_secondary_status)(unsigned int bank); |
| void (*set_ioforce)(bool enable); |
| spinlock_t lock; |
| bool sleepmode; |
| /* Keep track of configured edges */ |
| u32 edge_rising; |
| u32 edge_falling; |
| u32 real_wake; |
| u32 rwimsc; |
| u32 fwimsc; |
| u32 rimsc; |
| u32 fimsc; |
| u32 pull_up; |
| u32 lowemi; |
| }; |
| |
| struct nmk_pinctrl { |
| struct device *dev; |
| struct pinctrl_dev *pctl; |
| const struct nmk_pinctrl_soc_data *soc; |
| }; |
| |
| static struct nmk_gpio_chip * |
| nmk_gpio_chips[DIV_ROUND_UP(ARCH_NR_GPIOS, NMK_GPIO_PER_CHIP)]; |
| |
| static DEFINE_SPINLOCK(nmk_gpio_slpm_lock); |
| |
| #define NUM_BANKS ARRAY_SIZE(nmk_gpio_chips) |
| |
| static void __nmk_gpio_set_mode(struct nmk_gpio_chip *nmk_chip, |
| unsigned offset, int gpio_mode) |
| { |
| u32 bit = 1 << offset; |
| u32 afunc, bfunc; |
| |
| afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & ~bit; |
| bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & ~bit; |
| if (gpio_mode & NMK_GPIO_ALT_A) |
| afunc |= bit; |
| if (gpio_mode & NMK_GPIO_ALT_B) |
| bfunc |= bit; |
| writel(afunc, nmk_chip->addr + NMK_GPIO_AFSLA); |
| writel(bfunc, nmk_chip->addr + NMK_GPIO_AFSLB); |
| } |
| |
| static void __nmk_gpio_set_slpm(struct nmk_gpio_chip *nmk_chip, |
| unsigned offset, enum nmk_gpio_slpm mode) |
| { |
| u32 bit = 1 << offset; |
| u32 slpm; |
| |
| slpm = readl(nmk_chip->addr + NMK_GPIO_SLPC); |
| if (mode == NMK_GPIO_SLPM_NOCHANGE) |
| slpm |= bit; |
| else |
| slpm &= ~bit; |
| writel(slpm, nmk_chip->addr + NMK_GPIO_SLPC); |
| } |
| |
| static void __nmk_gpio_set_pull(struct nmk_gpio_chip *nmk_chip, |
| unsigned offset, enum nmk_gpio_pull pull) |
| { |
| u32 bit = 1 << offset; |
| u32 pdis; |
| |
| pdis = readl(nmk_chip->addr + NMK_GPIO_PDIS); |
| if (pull == NMK_GPIO_PULL_NONE) { |
| pdis |= bit; |
| nmk_chip->pull_up &= ~bit; |
| } else { |
| pdis &= ~bit; |
| } |
| |
| writel(pdis, nmk_chip->addr + NMK_GPIO_PDIS); |
| |
| if (pull == NMK_GPIO_PULL_UP) { |
| nmk_chip->pull_up |= bit; |
| writel(bit, nmk_chip->addr + NMK_GPIO_DATS); |
| } else if (pull == NMK_GPIO_PULL_DOWN) { |
| nmk_chip->pull_up &= ~bit; |
| writel(bit, nmk_chip->addr + NMK_GPIO_DATC); |
| } |
| } |
| |
| static void __nmk_gpio_set_lowemi(struct nmk_gpio_chip *nmk_chip, |
| unsigned offset, bool lowemi) |
| { |
| u32 bit = BIT(offset); |
| bool enabled = nmk_chip->lowemi & bit; |
| |
| if (lowemi == enabled) |
| return; |
| |
| if (lowemi) |
| nmk_chip->lowemi |= bit; |
| else |
| nmk_chip->lowemi &= ~bit; |
| |
| writel_relaxed(nmk_chip->lowemi, |
| nmk_chip->addr + NMK_GPIO_LOWEMI); |
| } |
| |
| static void __nmk_gpio_make_input(struct nmk_gpio_chip *nmk_chip, |
| unsigned offset) |
| { |
| writel(1 << offset, nmk_chip->addr + NMK_GPIO_DIRC); |
| } |
| |
| static void __nmk_gpio_set_output(struct nmk_gpio_chip *nmk_chip, |
| unsigned offset, int val) |
| { |
| if (val) |
| writel(1 << offset, nmk_chip->addr + NMK_GPIO_DATS); |
| else |
| writel(1 << offset, nmk_chip->addr + NMK_GPIO_DATC); |
| } |
| |
| static void __nmk_gpio_make_output(struct nmk_gpio_chip *nmk_chip, |
| unsigned offset, int val) |
| { |
| writel(1 << offset, nmk_chip->addr + NMK_GPIO_DIRS); |
| __nmk_gpio_set_output(nmk_chip, offset, val); |
| } |
| |
| static void __nmk_gpio_set_mode_safe(struct nmk_gpio_chip *nmk_chip, |
| unsigned offset, int gpio_mode, |
| bool glitch) |
| { |
| u32 rwimsc = nmk_chip->rwimsc; |
| u32 fwimsc = nmk_chip->fwimsc; |
| |
| if (glitch && nmk_chip->set_ioforce) { |
| u32 bit = BIT(offset); |
| |
| /* Prevent spurious wakeups */ |
| writel(rwimsc & ~bit, nmk_chip->addr + NMK_GPIO_RWIMSC); |
| writel(fwimsc & ~bit, nmk_chip->addr + NMK_GPIO_FWIMSC); |
| |
| nmk_chip->set_ioforce(true); |
| } |
| |
| __nmk_gpio_set_mode(nmk_chip, offset, gpio_mode); |
| |
| if (glitch && nmk_chip->set_ioforce) { |
| nmk_chip->set_ioforce(false); |
| |
| writel(rwimsc, nmk_chip->addr + NMK_GPIO_RWIMSC); |
| writel(fwimsc, nmk_chip->addr + NMK_GPIO_FWIMSC); |
| } |
| } |
| |
| static void |
| nmk_gpio_disable_lazy_irq(struct nmk_gpio_chip *nmk_chip, unsigned offset) |
| { |
| u32 falling = nmk_chip->fimsc & BIT(offset); |
| u32 rising = nmk_chip->rimsc & BIT(offset); |
| int gpio = nmk_chip->chip.base + offset; |
| int irq = NOMADIK_GPIO_TO_IRQ(gpio); |
| struct irq_data *d = irq_get_irq_data(irq); |
| |
| if (!rising && !falling) |
| return; |
| |
| if (!d || !irqd_irq_disabled(d)) |
| return; |
| |
| if (rising) { |
| nmk_chip->rimsc &= ~BIT(offset); |
| writel_relaxed(nmk_chip->rimsc, |
| nmk_chip->addr + NMK_GPIO_RIMSC); |
| } |
| |
| if (falling) { |
| nmk_chip->fimsc &= ~BIT(offset); |
| writel_relaxed(nmk_chip->fimsc, |
| nmk_chip->addr + NMK_GPIO_FIMSC); |
| } |
| |
| dev_dbg(nmk_chip->chip.dev, "%d: clearing interrupt mask\n", gpio); |
| } |
| |
| static void __nmk_config_pin(struct nmk_gpio_chip *nmk_chip, unsigned offset, |
| pin_cfg_t cfg, bool sleep, unsigned int *slpmregs) |
| { |
| static const char *afnames[] = { |
| [NMK_GPIO_ALT_GPIO] = "GPIO", |
| [NMK_GPIO_ALT_A] = "A", |
| [NMK_GPIO_ALT_B] = "B", |
| [NMK_GPIO_ALT_C] = "C" |
| }; |
| static const char *pullnames[] = { |
| [NMK_GPIO_PULL_NONE] = "none", |
| [NMK_GPIO_PULL_UP] = "up", |
| [NMK_GPIO_PULL_DOWN] = "down", |
| [3] /* illegal */ = "??" |
| }; |
| static const char *slpmnames[] = { |
| [NMK_GPIO_SLPM_INPUT] = "input/wakeup", |
| [NMK_GPIO_SLPM_NOCHANGE] = "no-change/no-wakeup", |
| }; |
| |
| int pin = PIN_NUM(cfg); |
| int pull = PIN_PULL(cfg); |
| int af = PIN_ALT(cfg); |
| int slpm = PIN_SLPM(cfg); |
| int output = PIN_DIR(cfg); |
| int val = PIN_VAL(cfg); |
| bool glitch = af == NMK_GPIO_ALT_C; |
| |
| dev_dbg(nmk_chip->chip.dev, "pin %d [%#lx]: af %s, pull %s, slpm %s (%s%s)\n", |
| pin, cfg, afnames[af], pullnames[pull], slpmnames[slpm], |
| output ? "output " : "input", |
| output ? (val ? "high" : "low") : ""); |
| |
| if (sleep) { |
| int slpm_pull = PIN_SLPM_PULL(cfg); |
| int slpm_output = PIN_SLPM_DIR(cfg); |
| int slpm_val = PIN_SLPM_VAL(cfg); |
| |
| af = NMK_GPIO_ALT_GPIO; |
| |
| /* |
| * The SLPM_* values are normal values + 1 to allow zero to |
| * mean "same as normal". |
| */ |
| if (slpm_pull) |
| pull = slpm_pull - 1; |
| if (slpm_output) |
| output = slpm_output - 1; |
| if (slpm_val) |
| val = slpm_val - 1; |
| |
| dev_dbg(nmk_chip->chip.dev, "pin %d: sleep pull %s, dir %s, val %s\n", |
| pin, |
| slpm_pull ? pullnames[pull] : "same", |
| slpm_output ? (output ? "output" : "input") : "same", |
| slpm_val ? (val ? "high" : "low") : "same"); |
| } |
| |
| if (output) |
| __nmk_gpio_make_output(nmk_chip, offset, val); |
| else { |
| __nmk_gpio_make_input(nmk_chip, offset); |
| __nmk_gpio_set_pull(nmk_chip, offset, pull); |
| } |
| |
| __nmk_gpio_set_lowemi(nmk_chip, offset, PIN_LOWEMI(cfg)); |
| |
| /* |
| * If the pin is switching to altfunc, and there was an interrupt |
| * installed on it which has been lazy disabled, actually mask the |
| * interrupt to prevent spurious interrupts that would occur while the |
| * pin is under control of the peripheral. Only SKE does this. |
| */ |
| if (af != NMK_GPIO_ALT_GPIO) |
| nmk_gpio_disable_lazy_irq(nmk_chip, offset); |
| |
| /* |
| * If we've backed up the SLPM registers (glitch workaround), modify |
| * the backups since they will be restored. |
| */ |
| if (slpmregs) { |
| if (slpm == NMK_GPIO_SLPM_NOCHANGE) |
| slpmregs[nmk_chip->bank] |= BIT(offset); |
| else |
| slpmregs[nmk_chip->bank] &= ~BIT(offset); |
| } else |
| __nmk_gpio_set_slpm(nmk_chip, offset, slpm); |
| |
| __nmk_gpio_set_mode_safe(nmk_chip, offset, af, glitch); |
| } |
| |
| /* |
| * Safe sequence used to switch IOs between GPIO and Alternate-C mode: |
| * - Save SLPM registers |
| * - Set SLPM=0 for the IOs you want to switch and others to 1 |
| * - Configure the GPIO registers for the IOs that are being switched |
| * - Set IOFORCE=1 |
| * - Modify the AFLSA/B registers for the IOs that are being switched |
| * - Set IOFORCE=0 |
| * - Restore SLPM registers |
| * - Any spurious wake up event during switch sequence to be ignored and |
| * cleared |
| */ |
| static void nmk_gpio_glitch_slpm_init(unsigned int *slpm) |
| { |
| int i; |
| |
| for (i = 0; i < NUM_BANKS; i++) { |
| struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; |
| unsigned int temp = slpm[i]; |
| |
| if (!chip) |
| break; |
| |
| clk_enable(chip->clk); |
| |
| slpm[i] = readl(chip->addr + NMK_GPIO_SLPC); |
| writel(temp, chip->addr + NMK_GPIO_SLPC); |
| } |
| } |
| |
| static void nmk_gpio_glitch_slpm_restore(unsigned int *slpm) |
| { |
| int i; |
| |
| for (i = 0; i < NUM_BANKS; i++) { |
| struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; |
| |
| if (!chip) |
| break; |
| |
| writel(slpm[i], chip->addr + NMK_GPIO_SLPC); |
| |
| clk_disable(chip->clk); |
| } |
| } |
| |
| static int __nmk_config_pins(pin_cfg_t *cfgs, int num, bool sleep) |
| { |
| static unsigned int slpm[NUM_BANKS]; |
| unsigned long flags; |
| bool glitch = false; |
| int ret = 0; |
| int i; |
| |
| for (i = 0; i < num; i++) { |
| if (PIN_ALT(cfgs[i]) == NMK_GPIO_ALT_C) { |
| glitch = true; |
| break; |
| } |
| } |
| |
| spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); |
| |
| if (glitch) { |
| memset(slpm, 0xff, sizeof(slpm)); |
| |
| for (i = 0; i < num; i++) { |
| int pin = PIN_NUM(cfgs[i]); |
| int offset = pin % NMK_GPIO_PER_CHIP; |
| |
| if (PIN_ALT(cfgs[i]) == NMK_GPIO_ALT_C) |
| slpm[pin / NMK_GPIO_PER_CHIP] &= ~BIT(offset); |
| } |
| |
| nmk_gpio_glitch_slpm_init(slpm); |
| } |
| |
| for (i = 0; i < num; i++) { |
| struct nmk_gpio_chip *nmk_chip; |
| int pin = PIN_NUM(cfgs[i]); |
| |
| nmk_chip = nmk_gpio_chips[pin / NMK_GPIO_PER_CHIP]; |
| if (!nmk_chip) { |
| ret = -EINVAL; |
| break; |
| } |
| |
| clk_enable(nmk_chip->clk); |
| spin_lock(&nmk_chip->lock); |
| __nmk_config_pin(nmk_chip, pin % NMK_GPIO_PER_CHIP, |
| cfgs[i], sleep, glitch ? slpm : NULL); |
| spin_unlock(&nmk_chip->lock); |
| clk_disable(nmk_chip->clk); |
| } |
| |
| if (glitch) |
| nmk_gpio_glitch_slpm_restore(slpm); |
| |
| spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); |
| |
| return ret; |
| } |
| |
| /** |
| * nmk_config_pin - configure a pin's mux attributes |
| * @cfg: pin confguration |
| * |
| * Configures a pin's mode (alternate function or GPIO), its pull up status, |
| * and its sleep mode based on the specified configuration. The @cfg is |
| * usually one of the SoC specific macros defined in mach/<soc>-pins.h. These |
| * are constructed using, and can be further enhanced with, the macros in |
| * plat/pincfg.h. |
| * |
| * If a pin's mode is set to GPIO, it is configured as an input to avoid |
| * side-effects. The gpio can be manipulated later using standard GPIO API |
| * calls. |
| */ |
| int nmk_config_pin(pin_cfg_t cfg, bool sleep) |
| { |
| return __nmk_config_pins(&cfg, 1, sleep); |
| } |
| EXPORT_SYMBOL(nmk_config_pin); |
| |
| /** |
| * nmk_config_pins - configure several pins at once |
| * @cfgs: array of pin configurations |
| * @num: number of elments in the array |
| * |
| * Configures several pins using nmk_config_pin(). Refer to that function for |
| * further information. |
| */ |
| int nmk_config_pins(pin_cfg_t *cfgs, int num) |
| { |
| return __nmk_config_pins(cfgs, num, false); |
| } |
| EXPORT_SYMBOL(nmk_config_pins); |
| |
| int nmk_config_pins_sleep(pin_cfg_t *cfgs, int num) |
| { |
| return __nmk_config_pins(cfgs, num, true); |
| } |
| EXPORT_SYMBOL(nmk_config_pins_sleep); |
| |
| /** |
| * nmk_gpio_set_slpm() - configure the sleep mode of a pin |
| * @gpio: pin number |
| * @mode: NMK_GPIO_SLPM_INPUT or NMK_GPIO_SLPM_NOCHANGE, |
| * |
| * This register is actually in the pinmux layer, not the GPIO block itself. |
| * The GPIO1B_SLPM register defines the GPIO mode when SLEEP/DEEP-SLEEP |
| * mode is entered (i.e. when signal IOFORCE is HIGH by the platform code). |
| * Each GPIO can be configured to be forced into GPIO mode when IOFORCE is |
| * HIGH, overriding the normal setting defined by GPIO_AFSELx registers. |
| * When IOFORCE returns LOW (by software, after SLEEP/DEEP-SLEEP exit), |
| * the GPIOs return to the normal setting defined by GPIO_AFSELx registers. |
| * |
| * If @mode is NMK_GPIO_SLPM_INPUT, the corresponding GPIO is switched to GPIO |
| * mode when signal IOFORCE is HIGH (i.e. when SLEEP/DEEP-SLEEP mode is |
| * entered) regardless of the altfunction selected. Also wake-up detection is |
| * ENABLED. |
| * |
| * If @mode is NMK_GPIO_SLPM_NOCHANGE, the corresponding GPIO remains |
| * controlled by NMK_GPIO_DATC, NMK_GPIO_DATS, NMK_GPIO_DIR, NMK_GPIO_PDIS |
| * (for altfunction GPIO) or respective on-chip peripherals (for other |
| * altfuncs) when IOFORCE is HIGH. Also wake-up detection DISABLED. |
| * |
| * Note that enable_irq_wake() will automatically enable wakeup detection. |
| */ |
| int nmk_gpio_set_slpm(int gpio, enum nmk_gpio_slpm mode) |
| { |
| struct nmk_gpio_chip *nmk_chip; |
| unsigned long flags; |
| |
| nmk_chip = nmk_gpio_chips[gpio / NMK_GPIO_PER_CHIP]; |
| if (!nmk_chip) |
| return -EINVAL; |
| |
| clk_enable(nmk_chip->clk); |
| spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); |
| spin_lock(&nmk_chip->lock); |
| |
| __nmk_gpio_set_slpm(nmk_chip, gpio % NMK_GPIO_PER_CHIP, mode); |
| |
| spin_unlock(&nmk_chip->lock); |
| spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); |
| clk_disable(nmk_chip->clk); |
| |
| return 0; |
| } |
| |
| /** |
| * nmk_gpio_set_pull() - enable/disable pull up/down on a gpio |
| * @gpio: pin number |
| * @pull: one of NMK_GPIO_PULL_DOWN, NMK_GPIO_PULL_UP, and NMK_GPIO_PULL_NONE |
| * |
| * Enables/disables pull up/down on a specified pin. This only takes effect if |
| * the pin is configured as an input (either explicitly or by the alternate |
| * function). |
| * |
| * NOTE: If enabling the pull up/down, the caller must ensure that the GPIO is |
| * configured as an input. Otherwise, due to the way the controller registers |
| * work, this function will change the value output on the pin. |
| */ |
| int nmk_gpio_set_pull(int gpio, enum nmk_gpio_pull pull) |
| { |
| struct nmk_gpio_chip *nmk_chip; |
| unsigned long flags; |
| |
| nmk_chip = nmk_gpio_chips[gpio / NMK_GPIO_PER_CHIP]; |
| if (!nmk_chip) |
| return -EINVAL; |
| |
| clk_enable(nmk_chip->clk); |
| spin_lock_irqsave(&nmk_chip->lock, flags); |
| __nmk_gpio_set_pull(nmk_chip, gpio % NMK_GPIO_PER_CHIP, pull); |
| spin_unlock_irqrestore(&nmk_chip->lock, flags); |
| clk_disable(nmk_chip->clk); |
| |
| return 0; |
| } |
| |
| /* Mode functions */ |
| /** |
| * nmk_gpio_set_mode() - set the mux mode of a gpio pin |
| * @gpio: pin number |
| * @gpio_mode: one of NMK_GPIO_ALT_GPIO, NMK_GPIO_ALT_A, |
| * NMK_GPIO_ALT_B, and NMK_GPIO_ALT_C |
| * |
| * Sets the mode of the specified pin to one of the alternate functions or |
| * plain GPIO. |
| */ |
| int nmk_gpio_set_mode(int gpio, int gpio_mode) |
| { |
| struct nmk_gpio_chip *nmk_chip; |
| unsigned long flags; |
| |
| nmk_chip = nmk_gpio_chips[gpio / NMK_GPIO_PER_CHIP]; |
| if (!nmk_chip) |
| return -EINVAL; |
| |
| clk_enable(nmk_chip->clk); |
| spin_lock_irqsave(&nmk_chip->lock, flags); |
| __nmk_gpio_set_mode(nmk_chip, gpio % NMK_GPIO_PER_CHIP, gpio_mode); |
| spin_unlock_irqrestore(&nmk_chip->lock, flags); |
| clk_disable(nmk_chip->clk); |
| |
| return 0; |
| } |
| EXPORT_SYMBOL(nmk_gpio_set_mode); |
| |
| int nmk_gpio_get_mode(int gpio) |
| { |
| struct nmk_gpio_chip *nmk_chip; |
| u32 afunc, bfunc, bit; |
| |
| nmk_chip = nmk_gpio_chips[gpio / NMK_GPIO_PER_CHIP]; |
| if (!nmk_chip) |
| return -EINVAL; |
| |
| bit = 1 << (gpio % NMK_GPIO_PER_CHIP); |
| |
| clk_enable(nmk_chip->clk); |
| |
| afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & bit; |
| bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & bit; |
| |
| clk_disable(nmk_chip->clk); |
| |
| return (afunc ? NMK_GPIO_ALT_A : 0) | (bfunc ? NMK_GPIO_ALT_B : 0); |
| } |
| EXPORT_SYMBOL(nmk_gpio_get_mode); |
| |
| |
| /* IRQ functions */ |
| static inline int nmk_gpio_get_bitmask(int gpio) |
| { |
| return 1 << (gpio % NMK_GPIO_PER_CHIP); |
| } |
| |
| static void nmk_gpio_irq_ack(struct irq_data *d) |
| { |
| struct nmk_gpio_chip *nmk_chip; |
| |
| nmk_chip = irq_data_get_irq_chip_data(d); |
| if (!nmk_chip) |
| return; |
| |
| clk_enable(nmk_chip->clk); |
| writel(nmk_gpio_get_bitmask(d->hwirq), nmk_chip->addr + NMK_GPIO_IC); |
| clk_disable(nmk_chip->clk); |
| } |
| |
| enum nmk_gpio_irq_type { |
| NORMAL, |
| WAKE, |
| }; |
| |
| static void __nmk_gpio_irq_modify(struct nmk_gpio_chip *nmk_chip, |
| int gpio, enum nmk_gpio_irq_type which, |
| bool enable) |
| { |
| u32 bitmask = nmk_gpio_get_bitmask(gpio); |
| u32 *rimscval; |
| u32 *fimscval; |
| u32 rimscreg; |
| u32 fimscreg; |
| |
| if (which == NORMAL) { |
| rimscreg = NMK_GPIO_RIMSC; |
| fimscreg = NMK_GPIO_FIMSC; |
| rimscval = &nmk_chip->rimsc; |
| fimscval = &nmk_chip->fimsc; |
| } else { |
| rimscreg = NMK_GPIO_RWIMSC; |
| fimscreg = NMK_GPIO_FWIMSC; |
| rimscval = &nmk_chip->rwimsc; |
| fimscval = &nmk_chip->fwimsc; |
| } |
| |
| /* we must individually set/clear the two edges */ |
| if (nmk_chip->edge_rising & bitmask) { |
| if (enable) |
| *rimscval |= bitmask; |
| else |
| *rimscval &= ~bitmask; |
| writel(*rimscval, nmk_chip->addr + rimscreg); |
| } |
| if (nmk_chip->edge_falling & bitmask) { |
| if (enable) |
| *fimscval |= bitmask; |
| else |
| *fimscval &= ~bitmask; |
| writel(*fimscval, nmk_chip->addr + fimscreg); |
| } |
| } |
| |
| static void __nmk_gpio_set_wake(struct nmk_gpio_chip *nmk_chip, |
| int gpio, bool on) |
| { |
| /* |
| * Ensure WAKEUP_ENABLE is on. No need to disable it if wakeup is |
| * disabled, since setting SLPM to 1 increases power consumption, and |
| * wakeup is anyhow controlled by the RIMSC and FIMSC registers. |
| */ |
| if (nmk_chip->sleepmode && on) { |
| __nmk_gpio_set_slpm(nmk_chip, gpio % NMK_GPIO_PER_CHIP, |
| NMK_GPIO_SLPM_WAKEUP_ENABLE); |
| } |
| |
| __nmk_gpio_irq_modify(nmk_chip, gpio, WAKE, on); |
| } |
| |
| static int nmk_gpio_irq_maskunmask(struct irq_data *d, bool enable) |
| { |
| struct nmk_gpio_chip *nmk_chip; |
| unsigned long flags; |
| u32 bitmask; |
| |
| nmk_chip = irq_data_get_irq_chip_data(d); |
| bitmask = nmk_gpio_get_bitmask(d->hwirq); |
| if (!nmk_chip) |
| return -EINVAL; |
| |
| clk_enable(nmk_chip->clk); |
| spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); |
| spin_lock(&nmk_chip->lock); |
| |
| __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, enable); |
| |
| if (!(nmk_chip->real_wake & bitmask)) |
| __nmk_gpio_set_wake(nmk_chip, d->hwirq, enable); |
| |
| spin_unlock(&nmk_chip->lock); |
| spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); |
| clk_disable(nmk_chip->clk); |
| |
| return 0; |
| } |
| |
| static void nmk_gpio_irq_mask(struct irq_data *d) |
| { |
| nmk_gpio_irq_maskunmask(d, false); |
| } |
| |
| static void nmk_gpio_irq_unmask(struct irq_data *d) |
| { |
| nmk_gpio_irq_maskunmask(d, true); |
| } |
| |
| static int nmk_gpio_irq_set_wake(struct irq_data *d, unsigned int on) |
| { |
| struct nmk_gpio_chip *nmk_chip; |
| unsigned long flags; |
| u32 bitmask; |
| |
| nmk_chip = irq_data_get_irq_chip_data(d); |
| if (!nmk_chip) |
| return -EINVAL; |
| bitmask = nmk_gpio_get_bitmask(d->hwirq); |
| |
| clk_enable(nmk_chip->clk); |
| spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); |
| spin_lock(&nmk_chip->lock); |
| |
| if (irqd_irq_disabled(d)) |
| __nmk_gpio_set_wake(nmk_chip, d->hwirq, on); |
| |
| if (on) |
| nmk_chip->real_wake |= bitmask; |
| else |
| nmk_chip->real_wake &= ~bitmask; |
| |
| spin_unlock(&nmk_chip->lock); |
| spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); |
| clk_disable(nmk_chip->clk); |
| |
| return 0; |
| } |
| |
| static int nmk_gpio_irq_set_type(struct irq_data *d, unsigned int type) |
| { |
| bool enabled = !irqd_irq_disabled(d); |
| bool wake = irqd_is_wakeup_set(d); |
| struct nmk_gpio_chip *nmk_chip; |
| unsigned long flags; |
| u32 bitmask; |
| |
| nmk_chip = irq_data_get_irq_chip_data(d); |
| bitmask = nmk_gpio_get_bitmask(d->hwirq); |
| if (!nmk_chip) |
| return -EINVAL; |
| if (type & IRQ_TYPE_LEVEL_HIGH) |
| return -EINVAL; |
| if (type & IRQ_TYPE_LEVEL_LOW) |
| return -EINVAL; |
| |
| clk_enable(nmk_chip->clk); |
| spin_lock_irqsave(&nmk_chip->lock, flags); |
| |
| if (enabled) |
| __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, false); |
| |
| if (enabled || wake) |
| __nmk_gpio_irq_modify(nmk_chip, d->hwirq, WAKE, false); |
| |
| nmk_chip->edge_rising &= ~bitmask; |
| if (type & IRQ_TYPE_EDGE_RISING) |
| nmk_chip->edge_rising |= bitmask; |
| |
| nmk_chip->edge_falling &= ~bitmask; |
| if (type & IRQ_TYPE_EDGE_FALLING) |
| nmk_chip->edge_falling |= bitmask; |
| |
| if (enabled) |
| __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, true); |
| |
| if (enabled || wake) |
| __nmk_gpio_irq_modify(nmk_chip, d->hwirq, WAKE, true); |
| |
| spin_unlock_irqrestore(&nmk_chip->lock, flags); |
| clk_disable(nmk_chip->clk); |
| |
| return 0; |
| } |
| |
| static unsigned int nmk_gpio_irq_startup(struct irq_data *d) |
| { |
| struct nmk_gpio_chip *nmk_chip = irq_data_get_irq_chip_data(d); |
| |
| clk_enable(nmk_chip->clk); |
| nmk_gpio_irq_unmask(d); |
| return 0; |
| } |
| |
| static void nmk_gpio_irq_shutdown(struct irq_data *d) |
| { |
| struct nmk_gpio_chip *nmk_chip = irq_data_get_irq_chip_data(d); |
| |
| nmk_gpio_irq_mask(d); |
| clk_disable(nmk_chip->clk); |
| } |
| |
| static struct irq_chip nmk_gpio_irq_chip = { |
| .name = "Nomadik-GPIO", |
| .irq_ack = nmk_gpio_irq_ack, |
| .irq_mask = nmk_gpio_irq_mask, |
| .irq_unmask = nmk_gpio_irq_unmask, |
| .irq_set_type = nmk_gpio_irq_set_type, |
| .irq_set_wake = nmk_gpio_irq_set_wake, |
| .irq_startup = nmk_gpio_irq_startup, |
| .irq_shutdown = nmk_gpio_irq_shutdown, |
| }; |
| |
| static void __nmk_gpio_irq_handler(unsigned int irq, struct irq_desc *desc, |
| u32 status) |
| { |
| struct nmk_gpio_chip *nmk_chip; |
| struct irq_chip *host_chip = irq_get_chip(irq); |
| unsigned int first_irq; |
| |
| chained_irq_enter(host_chip, desc); |
| |
| nmk_chip = irq_get_handler_data(irq); |
| first_irq = nmk_chip->domain->revmap_data.legacy.first_irq; |
| while (status) { |
| int bit = __ffs(status); |
| |
| generic_handle_irq(first_irq + bit); |
| status &= ~BIT(bit); |
| } |
| |
| chained_irq_exit(host_chip, desc); |
| } |
| |
| static void nmk_gpio_irq_handler(unsigned int irq, struct irq_desc *desc) |
| { |
| struct nmk_gpio_chip *nmk_chip = irq_get_handler_data(irq); |
| u32 status; |
| |
| clk_enable(nmk_chip->clk); |
| status = readl(nmk_chip->addr + NMK_GPIO_IS); |
| clk_disable(nmk_chip->clk); |
| |
| __nmk_gpio_irq_handler(irq, desc, status); |
| } |
| |
| static void nmk_gpio_secondary_irq_handler(unsigned int irq, |
| struct irq_desc *desc) |
| { |
| struct nmk_gpio_chip *nmk_chip = irq_get_handler_data(irq); |
| u32 status = nmk_chip->get_secondary_status(nmk_chip->bank); |
| |
| __nmk_gpio_irq_handler(irq, desc, status); |
| } |
| |
| static int nmk_gpio_init_irq(struct nmk_gpio_chip *nmk_chip) |
| { |
| irq_set_chained_handler(nmk_chip->parent_irq, nmk_gpio_irq_handler); |
| irq_set_handler_data(nmk_chip->parent_irq, nmk_chip); |
| |
| if (nmk_chip->secondary_parent_irq >= 0) { |
| irq_set_chained_handler(nmk_chip->secondary_parent_irq, |
| nmk_gpio_secondary_irq_handler); |
| irq_set_handler_data(nmk_chip->secondary_parent_irq, nmk_chip); |
| } |
| |
| return 0; |
| } |
| |
| /* I/O Functions */ |
| |
| static int nmk_gpio_request(struct gpio_chip *chip, unsigned offset) |
| { |
| /* |
| * Map back to global GPIO space and request muxing, the direction |
| * parameter does not matter for this controller. |
| */ |
| int gpio = chip->base + offset; |
| |
| return pinctrl_request_gpio(gpio); |
| } |
| |
| static void nmk_gpio_free(struct gpio_chip *chip, unsigned offset) |
| { |
| int gpio = chip->base + offset; |
| |
| pinctrl_free_gpio(gpio); |
| } |
| |
| static int nmk_gpio_make_input(struct gpio_chip *chip, unsigned offset) |
| { |
| struct nmk_gpio_chip *nmk_chip = |
| container_of(chip, struct nmk_gpio_chip, chip); |
| |
| clk_enable(nmk_chip->clk); |
| |
| writel(1 << offset, nmk_chip->addr + NMK_GPIO_DIRC); |
| |
| clk_disable(nmk_chip->clk); |
| |
| return 0; |
| } |
| |
| static int nmk_gpio_get_input(struct gpio_chip *chip, unsigned offset) |
| { |
| struct nmk_gpio_chip *nmk_chip = |
| container_of(chip, struct nmk_gpio_chip, chip); |
| u32 bit = 1 << offset; |
| int value; |
| |
| clk_enable(nmk_chip->clk); |
| |
| value = (readl(nmk_chip->addr + NMK_GPIO_DAT) & bit) != 0; |
| |
| clk_disable(nmk_chip->clk); |
| |
| return value; |
| } |
| |
| static void nmk_gpio_set_output(struct gpio_chip *chip, unsigned offset, |
| int val) |
| { |
| struct nmk_gpio_chip *nmk_chip = |
| container_of(chip, struct nmk_gpio_chip, chip); |
| |
| clk_enable(nmk_chip->clk); |
| |
| __nmk_gpio_set_output(nmk_chip, offset, val); |
| |
| clk_disable(nmk_chip->clk); |
| } |
| |
| static int nmk_gpio_make_output(struct gpio_chip *chip, unsigned offset, |
| int val) |
| { |
| struct nmk_gpio_chip *nmk_chip = |
| container_of(chip, struct nmk_gpio_chip, chip); |
| |
| clk_enable(nmk_chip->clk); |
| |
| __nmk_gpio_make_output(nmk_chip, offset, val); |
| |
| clk_disable(nmk_chip->clk); |
| |
| return 0; |
| } |
| |
| static int nmk_gpio_to_irq(struct gpio_chip *chip, unsigned offset) |
| { |
| struct nmk_gpio_chip *nmk_chip = |
| container_of(chip, struct nmk_gpio_chip, chip); |
| |
| return irq_find_mapping(nmk_chip->domain, offset); |
| } |
| |
| #ifdef CONFIG_DEBUG_FS |
| |
| #include <linux/seq_file.h> |
| |
| static void nmk_gpio_dbg_show_one(struct seq_file *s, struct gpio_chip *chip, |
| unsigned offset, unsigned gpio) |
| { |
| const char *label = gpiochip_is_requested(chip, offset); |
| struct nmk_gpio_chip *nmk_chip = |
| container_of(chip, struct nmk_gpio_chip, chip); |
| int mode; |
| bool is_out; |
| bool pull; |
| u32 bit = 1 << offset; |
| const char *modes[] = { |
| [NMK_GPIO_ALT_GPIO] = "gpio", |
| [NMK_GPIO_ALT_A] = "altA", |
| [NMK_GPIO_ALT_B] = "altB", |
| [NMK_GPIO_ALT_C] = "altC", |
| }; |
| |
| clk_enable(nmk_chip->clk); |
| is_out = !!(readl(nmk_chip->addr + NMK_GPIO_DIR) & bit); |
| pull = !(readl(nmk_chip->addr + NMK_GPIO_PDIS) & bit); |
| mode = nmk_gpio_get_mode(gpio); |
| |
| seq_printf(s, " gpio-%-3d (%-20.20s) %s %s %s %s", |
| gpio, label ?: "(none)", |
| is_out ? "out" : "in ", |
| chip->get |
| ? (chip->get(chip, offset) ? "hi" : "lo") |
| : "? ", |
| (mode < 0) ? "unknown" : modes[mode], |
| pull ? "pull" : "none"); |
| |
| if (label && !is_out) { |
| int irq = gpio_to_irq(gpio); |
| struct irq_desc *desc = irq_to_desc(irq); |
| |
| /* This races with request_irq(), set_irq_type(), |
| * and set_irq_wake() ... but those are "rare". |
| */ |
| if (irq >= 0 && desc->action) { |
| char *trigger; |
| u32 bitmask = nmk_gpio_get_bitmask(gpio); |
| |
| if (nmk_chip->edge_rising & bitmask) |
| trigger = "edge-rising"; |
| else if (nmk_chip->edge_falling & bitmask) |
| trigger = "edge-falling"; |
| else |
| trigger = "edge-undefined"; |
| |
| seq_printf(s, " irq-%d %s%s", |
| irq, trigger, |
| irqd_is_wakeup_set(&desc->irq_data) |
| ? " wakeup" : ""); |
| } |
| } |
| clk_disable(nmk_chip->clk); |
| } |
| |
| static void nmk_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip) |
| { |
| unsigned i; |
| unsigned gpio = chip->base; |
| |
| for (i = 0; i < chip->ngpio; i++, gpio++) { |
| nmk_gpio_dbg_show_one(s, chip, i, gpio); |
| seq_printf(s, "\n"); |
| } |
| } |
| |
| #else |
| static inline void nmk_gpio_dbg_show_one(struct seq_file *s, |
| struct gpio_chip *chip, |
| unsigned offset, unsigned gpio) |
| { |
| } |
| #define nmk_gpio_dbg_show NULL |
| #endif |
| |
| /* This structure is replicated for each GPIO block allocated at probe time */ |
| static struct gpio_chip nmk_gpio_template = { |
| .request = nmk_gpio_request, |
| .free = nmk_gpio_free, |
| .direction_input = nmk_gpio_make_input, |
| .get = nmk_gpio_get_input, |
| .direction_output = nmk_gpio_make_output, |
| .set = nmk_gpio_set_output, |
| .to_irq = nmk_gpio_to_irq, |
| .dbg_show = nmk_gpio_dbg_show, |
| .can_sleep = 0, |
| }; |
| |
| void nmk_gpio_clocks_enable(void) |
| { |
| int i; |
| |
| for (i = 0; i < NUM_BANKS; i++) { |
| struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; |
| |
| if (!chip) |
| continue; |
| |
| clk_enable(chip->clk); |
| } |
| } |
| |
| void nmk_gpio_clocks_disable(void) |
| { |
| int i; |
| |
| for (i = 0; i < NUM_BANKS; i++) { |
| struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; |
| |
| if (!chip) |
| continue; |
| |
| clk_disable(chip->clk); |
| } |
| } |
| |
| /* |
| * Called from the suspend/resume path to only keep the real wakeup interrupts |
| * (those that have had set_irq_wake() called on them) as wakeup interrupts, |
| * and not the rest of the interrupts which we needed to have as wakeups for |
| * cpuidle. |
| * |
| * PM ops are not used since this needs to be done at the end, after all the |
| * other drivers are done with their suspend callbacks. |
| */ |
| void nmk_gpio_wakeups_suspend(void) |
| { |
| int i; |
| |
| for (i = 0; i < NUM_BANKS; i++) { |
| struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; |
| |
| if (!chip) |
| break; |
| |
| clk_enable(chip->clk); |
| |
| writel(chip->rwimsc & chip->real_wake, |
| chip->addr + NMK_GPIO_RWIMSC); |
| writel(chip->fwimsc & chip->real_wake, |
| chip->addr + NMK_GPIO_FWIMSC); |
| |
| clk_disable(chip->clk); |
| } |
| } |
| |
| void nmk_gpio_wakeups_resume(void) |
| { |
| int i; |
| |
| for (i = 0; i < NUM_BANKS; i++) { |
| struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; |
| |
| if (!chip) |
| break; |
| |
| clk_enable(chip->clk); |
| |
| writel(chip->rwimsc, chip->addr + NMK_GPIO_RWIMSC); |
| writel(chip->fwimsc, chip->addr + NMK_GPIO_FWIMSC); |
| |
| clk_disable(chip->clk); |
| } |
| } |
| |
| /* |
| * Read the pull up/pull down status. |
| * A bit set in 'pull_up' means that pull up |
| * is selected if pull is enabled in PDIS register. |
| * Note: only pull up/down set via this driver can |
| * be detected due to HW limitations. |
| */ |
| void nmk_gpio_read_pull(int gpio_bank, u32 *pull_up) |
| { |
| if (gpio_bank < NUM_BANKS) { |
| struct nmk_gpio_chip *chip = nmk_gpio_chips[gpio_bank]; |
| |
| if (!chip) |
| return; |
| |
| *pull_up = chip->pull_up; |
| } |
| } |
| |
| int nmk_gpio_irq_map(struct irq_domain *d, unsigned int irq, |
| irq_hw_number_t hwirq) |
| { |
| struct nmk_gpio_chip *nmk_chip = d->host_data; |
| |
| if (!nmk_chip) |
| return -EINVAL; |
| |
| irq_set_chip_and_handler(irq, &nmk_gpio_irq_chip, handle_edge_irq); |
| set_irq_flags(irq, IRQF_VALID); |
| irq_set_chip_data(irq, nmk_chip); |
| irq_set_irq_type(irq, IRQ_TYPE_EDGE_FALLING); |
| |
| return 0; |
| } |
| |
| const struct irq_domain_ops nmk_gpio_irq_simple_ops = { |
| .map = nmk_gpio_irq_map, |
| .xlate = irq_domain_xlate_twocell, |
| }; |
| |
| static int __devinit nmk_gpio_probe(struct platform_device *dev) |
| { |
| struct nmk_gpio_platform_data *pdata = dev->dev.platform_data; |
| struct device_node *np = dev->dev.of_node; |
| struct nmk_gpio_chip *nmk_chip; |
| struct gpio_chip *chip; |
| struct resource *res; |
| struct clk *clk; |
| int secondary_irq; |
| void __iomem *base; |
| int irq; |
| int ret; |
| |
| if (!pdata && !np) { |
| dev_err(&dev->dev, "No platform data or device tree found\n"); |
| return -ENODEV; |
| } |
| |
| if (np) { |
| pdata = kzalloc(sizeof(*pdata), GFP_KERNEL); |
| if (!pdata) |
| return -ENOMEM; |
| |
| if (of_get_property(np, "supports-sleepmode", NULL)) |
| pdata->supports_sleepmode = true; |
| |
| if (of_property_read_u32(np, "gpio-bank", &dev->id)) { |
| dev_err(&dev->dev, "gpio-bank property not found\n"); |
| ret = -EINVAL; |
| goto out; |
| } |
| |
| pdata->first_gpio = dev->id * NMK_GPIO_PER_CHIP; |
| pdata->num_gpio = NMK_GPIO_PER_CHIP; |
| } |
| |
| res = platform_get_resource(dev, IORESOURCE_MEM, 0); |
| if (!res) { |
| ret = -ENOENT; |
| goto out; |
| } |
| |
| irq = platform_get_irq(dev, 0); |
| if (irq < 0) { |
| ret = irq; |
| goto out; |
| } |
| |
| secondary_irq = platform_get_irq(dev, 1); |
| if (secondary_irq >= 0 && !pdata->get_secondary_status) { |
| ret = -EINVAL; |
| goto out; |
| } |
| |
| if (request_mem_region(res->start, resource_size(res), |
| dev_name(&dev->dev)) == NULL) { |
| ret = -EBUSY; |
| goto out; |
| } |
| |
| base = ioremap(res->start, resource_size(res)); |
| if (!base) { |
| ret = -ENOMEM; |
| goto out_release; |
| } |
| |
| clk = clk_get(&dev->dev, NULL); |
| if (IS_ERR(clk)) { |
| ret = PTR_ERR(clk); |
| goto out_unmap; |
| } |
| clk_prepare(clk); |
| |
| nmk_chip = kzalloc(sizeof(*nmk_chip), GFP_KERNEL); |
| if (!nmk_chip) { |
| ret = -ENOMEM; |
| goto out_clk; |
| } |
| |
| /* |
| * The virt address in nmk_chip->addr is in the nomadik register space, |
| * so we can simply convert the resource address, without remapping |
| */ |
| nmk_chip->bank = dev->id; |
| nmk_chip->clk = clk; |
| nmk_chip->addr = base; |
| nmk_chip->chip = nmk_gpio_template; |
| nmk_chip->parent_irq = irq; |
| nmk_chip->secondary_parent_irq = secondary_irq; |
| nmk_chip->get_secondary_status = pdata->get_secondary_status; |
| nmk_chip->set_ioforce = pdata->set_ioforce; |
| nmk_chip->sleepmode = pdata->supports_sleepmode; |
| spin_lock_init(&nmk_chip->lock); |
| |
| chip = &nmk_chip->chip; |
| chip->base = pdata->first_gpio; |
| chip->ngpio = pdata->num_gpio; |
| chip->label = pdata->name ?: dev_name(&dev->dev); |
| chip->dev = &dev->dev; |
| chip->owner = THIS_MODULE; |
| |
| clk_enable(nmk_chip->clk); |
| nmk_chip->lowemi = readl_relaxed(nmk_chip->addr + NMK_GPIO_LOWEMI); |
| clk_disable(nmk_chip->clk); |
| |
| #ifdef CONFIG_OF_GPIO |
| chip->of_node = np; |
| #endif |
| |
| ret = gpiochip_add(&nmk_chip->chip); |
| if (ret) |
| goto out_free; |
| |
| BUG_ON(nmk_chip->bank >= ARRAY_SIZE(nmk_gpio_chips)); |
| |
| nmk_gpio_chips[nmk_chip->bank] = nmk_chip; |
| |
| platform_set_drvdata(dev, nmk_chip); |
| |
| nmk_chip->domain = irq_domain_add_legacy(np, NMK_GPIO_PER_CHIP, |
| NOMADIK_GPIO_TO_IRQ(pdata->first_gpio), |
| 0, &nmk_gpio_irq_simple_ops, nmk_chip); |
| if (!nmk_chip->domain) { |
| pr_err("%s: Failed to create irqdomain\n", np->full_name); |
| ret = -ENOSYS; |
| goto out_free; |
| } |
| |
| nmk_gpio_init_irq(nmk_chip); |
| |
| dev_info(&dev->dev, "at address %p\n", nmk_chip->addr); |
| |
| return 0; |
| |
| out_free: |
| kfree(nmk_chip); |
| out_clk: |
| clk_disable(clk); |
| clk_put(clk); |
| out_unmap: |
| iounmap(base); |
| out_release: |
| release_mem_region(res->start, resource_size(res)); |
| out: |
| dev_err(&dev->dev, "Failure %i for GPIO %i-%i\n", ret, |
| pdata->first_gpio, pdata->first_gpio+31); |
| if (np) |
| kfree(pdata); |
| |
| return ret; |
| } |
| |
| static int nmk_get_groups_cnt(struct pinctrl_dev *pctldev) |
| { |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| |
| return npct->soc->ngroups; |
| } |
| |
| static const char *nmk_get_group_name(struct pinctrl_dev *pctldev, |
| unsigned selector) |
| { |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| |
| return npct->soc->groups[selector].name; |
| } |
| |
| static int nmk_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector, |
| const unsigned **pins, |
| unsigned *num_pins) |
| { |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| |
| *pins = npct->soc->groups[selector].pins; |
| *num_pins = npct->soc->groups[selector].npins; |
| return 0; |
| } |
| |
| static struct pinctrl_gpio_range * |
| nmk_match_gpio_range(struct pinctrl_dev *pctldev, unsigned offset) |
| { |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| int i; |
| |
| for (i = 0; i < npct->soc->gpio_num_ranges; i++) { |
| struct pinctrl_gpio_range *range; |
| |
| range = &npct->soc->gpio_ranges[i]; |
| if (offset >= range->pin_base && |
| offset <= (range->pin_base + range->npins - 1)) |
| return range; |
| } |
| return NULL; |
| } |
| |
| static void nmk_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s, |
| unsigned offset) |
| { |
| struct pinctrl_gpio_range *range; |
| struct gpio_chip *chip; |
| |
| range = nmk_match_gpio_range(pctldev, offset); |
| if (!range || !range->gc) { |
| seq_printf(s, "invalid pin offset"); |
| return; |
| } |
| chip = range->gc; |
| nmk_gpio_dbg_show_one(s, chip, offset - chip->base, offset); |
| } |
| |
| static struct pinctrl_ops nmk_pinctrl_ops = { |
| .get_groups_count = nmk_get_groups_cnt, |
| .get_group_name = nmk_get_group_name, |
| .get_group_pins = nmk_get_group_pins, |
| .pin_dbg_show = nmk_pin_dbg_show, |
| }; |
| |
| static int nmk_pmx_get_funcs_cnt(struct pinctrl_dev *pctldev) |
| { |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| |
| return npct->soc->nfunctions; |
| } |
| |
| static const char *nmk_pmx_get_func_name(struct pinctrl_dev *pctldev, |
| unsigned function) |
| { |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| |
| return npct->soc->functions[function].name; |
| } |
| |
| static int nmk_pmx_get_func_groups(struct pinctrl_dev *pctldev, |
| unsigned function, |
| const char * const **groups, |
| unsigned * const num_groups) |
| { |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| |
| *groups = npct->soc->functions[function].groups; |
| *num_groups = npct->soc->functions[function].ngroups; |
| |
| return 0; |
| } |
| |
| static int nmk_pmx_enable(struct pinctrl_dev *pctldev, unsigned function, |
| unsigned group) |
| { |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| const struct nmk_pingroup *g; |
| static unsigned int slpm[NUM_BANKS]; |
| unsigned long flags; |
| bool glitch; |
| int ret = -EINVAL; |
| int i; |
| |
| g = &npct->soc->groups[group]; |
| |
| if (g->altsetting < 0) |
| return -EINVAL; |
| |
| dev_dbg(npct->dev, "enable group %s, %u pins\n", g->name, g->npins); |
| |
| /* Handle this special glitch on altfunction C */ |
| glitch = (g->altsetting == NMK_GPIO_ALT_C); |
| |
| if (glitch) { |
| spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); |
| |
| /* Initially don't put any pins to sleep when switching */ |
| memset(slpm, 0xff, sizeof(slpm)); |
| |
| /* |
| * Then mask the pins that need to be sleeping now when we're |
| * switching to the ALT C function. |
| */ |
| for (i = 0; i < g->npins; i++) |
| slpm[g->pins[i] / NMK_GPIO_PER_CHIP] &= ~BIT(g->pins[i]); |
| nmk_gpio_glitch_slpm_init(slpm); |
| } |
| |
| for (i = 0; i < g->npins; i++) { |
| struct pinctrl_gpio_range *range; |
| struct nmk_gpio_chip *nmk_chip; |
| struct gpio_chip *chip; |
| unsigned bit; |
| |
| range = nmk_match_gpio_range(pctldev, g->pins[i]); |
| if (!range) { |
| dev_err(npct->dev, |
| "invalid pin offset %d in group %s at index %d\n", |
| g->pins[i], g->name, i); |
| goto out_glitch; |
| } |
| if (!range->gc) { |
| dev_err(npct->dev, "GPIO chip missing in range for pin offset %d in group %s at index %d\n", |
| g->pins[i], g->name, i); |
| goto out_glitch; |
| } |
| chip = range->gc; |
| nmk_chip = container_of(chip, struct nmk_gpio_chip, chip); |
| dev_dbg(npct->dev, "setting pin %d to altsetting %d\n", g->pins[i], g->altsetting); |
| |
| clk_enable(nmk_chip->clk); |
| bit = g->pins[i] % NMK_GPIO_PER_CHIP; |
| /* |
| * If the pin is switching to altfunc, and there was an |
| * interrupt installed on it which has been lazy disabled, |
| * actually mask the interrupt to prevent spurious interrupts |
| * that would occur while the pin is under control of the |
| * peripheral. Only SKE does this. |
| */ |
| nmk_gpio_disable_lazy_irq(nmk_chip, bit); |
| |
| __nmk_gpio_set_mode_safe(nmk_chip, bit, g->altsetting, glitch); |
| clk_disable(nmk_chip->clk); |
| } |
| |
| /* When all pins are successfully reconfigured we get here */ |
| ret = 0; |
| |
| out_glitch: |
| if (glitch) { |
| nmk_gpio_glitch_slpm_restore(slpm); |
| spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); |
| } |
| |
| return ret; |
| } |
| |
| static void nmk_pmx_disable(struct pinctrl_dev *pctldev, |
| unsigned function, unsigned group) |
| { |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| const struct nmk_pingroup *g; |
| |
| g = &npct->soc->groups[group]; |
| |
| if (g->altsetting < 0) |
| return; |
| |
| /* Poke out the mux, set the pin to some default state? */ |
| dev_dbg(npct->dev, "disable group %s, %u pins\n", g->name, g->npins); |
| } |
| |
| int nmk_gpio_request_enable(struct pinctrl_dev *pctldev, |
| struct pinctrl_gpio_range *range, |
| unsigned offset) |
| { |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| struct nmk_gpio_chip *nmk_chip; |
| struct gpio_chip *chip; |
| unsigned bit; |
| |
| if (!range) { |
| dev_err(npct->dev, "invalid range\n"); |
| return -EINVAL; |
| } |
| if (!range->gc) { |
| dev_err(npct->dev, "missing GPIO chip in range\n"); |
| return -EINVAL; |
| } |
| chip = range->gc; |
| nmk_chip = container_of(chip, struct nmk_gpio_chip, chip); |
| |
| dev_dbg(npct->dev, "enable pin %u as GPIO\n", offset); |
| |
| clk_enable(nmk_chip->clk); |
| bit = offset % NMK_GPIO_PER_CHIP; |
| /* There is no glitch when converting any pin to GPIO */ |
| __nmk_gpio_set_mode(nmk_chip, bit, NMK_GPIO_ALT_GPIO); |
| clk_disable(nmk_chip->clk); |
| |
| return 0; |
| } |
| |
| void nmk_gpio_disable_free(struct pinctrl_dev *pctldev, |
| struct pinctrl_gpio_range *range, |
| unsigned offset) |
| { |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| |
| dev_dbg(npct->dev, "disable pin %u as GPIO\n", offset); |
| /* Set the pin to some default state, GPIO is usually default */ |
| } |
| |
| static struct pinmux_ops nmk_pinmux_ops = { |
| .get_functions_count = nmk_pmx_get_funcs_cnt, |
| .get_function_name = nmk_pmx_get_func_name, |
| .get_function_groups = nmk_pmx_get_func_groups, |
| .enable = nmk_pmx_enable, |
| .disable = nmk_pmx_disable, |
| .gpio_request_enable = nmk_gpio_request_enable, |
| .gpio_disable_free = nmk_gpio_disable_free, |
| }; |
| |
| int nmk_pin_config_get(struct pinctrl_dev *pctldev, |
| unsigned pin, |
| unsigned long *config) |
| { |
| /* Not implemented */ |
| return -EINVAL; |
| } |
| |
| int nmk_pin_config_set(struct pinctrl_dev *pctldev, |
| unsigned pin, |
| unsigned long config) |
| { |
| static const char *pullnames[] = { |
| [NMK_GPIO_PULL_NONE] = "none", |
| [NMK_GPIO_PULL_UP] = "up", |
| [NMK_GPIO_PULL_DOWN] = "down", |
| [3] /* illegal */ = "??" |
| }; |
| static const char *slpmnames[] = { |
| [NMK_GPIO_SLPM_INPUT] = "input/wakeup", |
| [NMK_GPIO_SLPM_NOCHANGE] = "no-change/no-wakeup", |
| }; |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); |
| struct nmk_gpio_chip *nmk_chip; |
| struct pinctrl_gpio_range *range; |
| struct gpio_chip *chip; |
| unsigned bit; |
| |
| /* |
| * The pin config contains pin number and altfunction fields, here |
| * we just ignore that part. It's being handled by the framework and |
| * pinmux callback respectively. |
| */ |
| pin_cfg_t cfg = (pin_cfg_t) config; |
| int pull = PIN_PULL(cfg); |
| int slpm = PIN_SLPM(cfg); |
| int output = PIN_DIR(cfg); |
| int val = PIN_VAL(cfg); |
| bool lowemi = PIN_LOWEMI(cfg); |
| bool gpiomode = PIN_GPIOMODE(cfg); |
| bool sleep = PIN_SLEEPMODE(cfg); |
| |
| range = nmk_match_gpio_range(pctldev, pin); |
| if (!range) { |
| dev_err(npct->dev, "invalid pin offset %d\n", pin); |
| return -EINVAL; |
| } |
| if (!range->gc) { |
| dev_err(npct->dev, "GPIO chip missing in range for pin %d\n", |
| pin); |
| return -EINVAL; |
| } |
| chip = range->gc; |
| nmk_chip = container_of(chip, struct nmk_gpio_chip, chip); |
| |
| if (sleep) { |
| int slpm_pull = PIN_SLPM_PULL(cfg); |
| int slpm_output = PIN_SLPM_DIR(cfg); |
| int slpm_val = PIN_SLPM_VAL(cfg); |
| |
| /* All pins go into GPIO mode at sleep */ |
| gpiomode = true; |
| |
| /* |
| * The SLPM_* values are normal values + 1 to allow zero to |
| * mean "same as normal". |
| */ |
| if (slpm_pull) |
| pull = slpm_pull - 1; |
| if (slpm_output) |
| output = slpm_output - 1; |
| if (slpm_val) |
| val = slpm_val - 1; |
| |
| dev_dbg(nmk_chip->chip.dev, "pin %d: sleep pull %s, dir %s, val %s\n", |
| pin, |
| slpm_pull ? pullnames[pull] : "same", |
| slpm_output ? (output ? "output" : "input") : "same", |
| slpm_val ? (val ? "high" : "low") : "same"); |
| } |
| |
| dev_dbg(nmk_chip->chip.dev, "pin %d [%#lx]: pull %s, slpm %s (%s%s), lowemi %s\n", |
| pin, cfg, pullnames[pull], slpmnames[slpm], |
| output ? "output " : "input", |
| output ? (val ? "high" : "low") : "", |
| lowemi ? "on" : "off" ); |
| |
| clk_enable(nmk_chip->clk); |
| bit = pin % NMK_GPIO_PER_CHIP; |
| if (gpiomode) |
| /* No glitch when going to GPIO mode */ |
| __nmk_gpio_set_mode(nmk_chip, bit, NMK_GPIO_ALT_GPIO); |
| if (output) |
| __nmk_gpio_make_output(nmk_chip, bit, val); |
| else { |
| __nmk_gpio_make_input(nmk_chip, bit); |
| __nmk_gpio_set_pull(nmk_chip, bit, pull); |
| } |
| /* TODO: isn't this only applicable on output pins? */ |
| __nmk_gpio_set_lowemi(nmk_chip, bit, lowemi); |
| |
| __nmk_gpio_set_slpm(nmk_chip, bit, slpm); |
| clk_disable(nmk_chip->clk); |
| return 0; |
| } |
| |
| static struct pinconf_ops nmk_pinconf_ops = { |
| .pin_config_get = nmk_pin_config_get, |
| .pin_config_set = nmk_pin_config_set, |
| }; |
| |
| static struct pinctrl_desc nmk_pinctrl_desc = { |
| .name = "pinctrl-nomadik", |
| .pctlops = &nmk_pinctrl_ops, |
| .pmxops = &nmk_pinmux_ops, |
| .confops = &nmk_pinconf_ops, |
| .owner = THIS_MODULE, |
| }; |
| |
| static const struct of_device_id nmk_pinctrl_match[] = { |
| { |
| .compatible = "stericsson,nmk_pinctrl", |
| .data = (void *)PINCTRL_NMK_DB8500, |
| }, |
| {}, |
| }; |
| |
| static int __devinit nmk_pinctrl_probe(struct platform_device *pdev) |
| { |
| const struct platform_device_id *platid = platform_get_device_id(pdev); |
| struct device_node *np = pdev->dev.of_node; |
| struct nmk_pinctrl *npct; |
| unsigned int version = 0; |
| int i; |
| |
| npct = devm_kzalloc(&pdev->dev, sizeof(*npct), GFP_KERNEL); |
| if (!npct) |
| return -ENOMEM; |
| |
| if (platid) |
| version = platid->driver_data; |
| else if (np) |
| version = (unsigned int) |
| of_match_device(nmk_pinctrl_match, &pdev->dev)->data; |
| |
| /* Poke in other ASIC variants here */ |
| if (version == PINCTRL_NMK_DB8500) |
| nmk_pinctrl_db8500_init(&npct->soc); |
| |
| /* |
| * We need all the GPIO drivers to probe FIRST, or we will not be able |
| * to obtain references to the struct gpio_chip * for them, and we |
| * need this to proceed. |
| */ |
| for (i = 0; i < npct->soc->gpio_num_ranges; i++) { |
| if (!nmk_gpio_chips[i]) { |
| dev_warn(&pdev->dev, "GPIO chip %d not registered yet\n", i); |
| devm_kfree(&pdev->dev, npct); |
| return -EPROBE_DEFER; |
| } |
| npct->soc->gpio_ranges[i].gc = &nmk_gpio_chips[i]->chip; |
| } |
| |
| nmk_pinctrl_desc.pins = npct->soc->pins; |
| nmk_pinctrl_desc.npins = npct->soc->npins; |
| npct->dev = &pdev->dev; |
| npct->pctl = pinctrl_register(&nmk_pinctrl_desc, &pdev->dev, npct); |
| if (!npct->pctl) { |
| dev_err(&pdev->dev, "could not register Nomadik pinctrl driver\n"); |
| return -EINVAL; |
| } |
| |
| /* We will handle a range of GPIO pins */ |
| for (i = 0; i < npct->soc->gpio_num_ranges; i++) |
| pinctrl_add_gpio_range(npct->pctl, &npct->soc->gpio_ranges[i]); |
| |
| platform_set_drvdata(pdev, npct); |
| dev_info(&pdev->dev, "initialized Nomadik pin control driver\n"); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id nmk_gpio_match[] = { |
| { .compatible = "st,nomadik-gpio", }, |
| {} |
| }; |
| |
| static struct platform_driver nmk_gpio_driver = { |
| .driver = { |
| .owner = THIS_MODULE, |
| .name = "gpio", |
| .of_match_table = nmk_gpio_match, |
| }, |
| .probe = nmk_gpio_probe, |
| }; |
| |
| static const struct platform_device_id nmk_pinctrl_id[] = { |
| { "pinctrl-stn8815", PINCTRL_NMK_STN8815 }, |
| { "pinctrl-db8500", PINCTRL_NMK_DB8500 }, |
| }; |
| |
| static struct platform_driver nmk_pinctrl_driver = { |
| .driver = { |
| .owner = THIS_MODULE, |
| .name = "pinctrl-nomadik", |
| .of_match_table = nmk_pinctrl_match, |
| }, |
| .probe = nmk_pinctrl_probe, |
| .id_table = nmk_pinctrl_id, |
| }; |
| |
| static int __init nmk_gpio_init(void) |
| { |
| int ret; |
| |
| ret = platform_driver_register(&nmk_gpio_driver); |
| if (ret) |
| return ret; |
| return platform_driver_register(&nmk_pinctrl_driver); |
| } |
| |
| core_initcall(nmk_gpio_init); |
| |
| MODULE_AUTHOR("Prafulla WADASKAR and Alessandro Rubini"); |
| MODULE_DESCRIPTION("Nomadik GPIO Driver"); |
| MODULE_LICENSE("GPL"); |