blob: 86858da9cc38f7a070b0c2f3c37c2baf0a0a95fd [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2020 Invensense, Inc.
*/
#include <linux/kernel.h>
#include <linux/device.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/mutex.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/regulator/consumer.h>
#include <linux/pm_runtime.h>
#include <linux/property.h>
#include <linux/regmap.h>
#include <linux/iio/iio.h>
#include "inv_icm42600.h"
#include "inv_icm42600_buffer.h"
#include "inv_icm42600_timestamp.h"
static const struct regmap_range_cfg inv_icm42600_regmap_ranges[] = {
{
.name = "user banks",
.range_min = 0x0000,
.range_max = 0x4FFF,
.selector_reg = INV_ICM42600_REG_BANK_SEL,
.selector_mask = INV_ICM42600_BANK_SEL_MASK,
.selector_shift = 0,
.window_start = 0,
.window_len = 0x1000,
},
};
const struct regmap_config inv_icm42600_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.max_register = 0x4FFF,
.ranges = inv_icm42600_regmap_ranges,
.num_ranges = ARRAY_SIZE(inv_icm42600_regmap_ranges),
};
EXPORT_SYMBOL_GPL(inv_icm42600_regmap_config);
struct inv_icm42600_hw {
uint8_t whoami;
const char *name;
const struct inv_icm42600_conf *conf;
};
/* chip initial default configuration */
static const struct inv_icm42600_conf inv_icm42600_default_conf = {
.gyro = {
.mode = INV_ICM42600_SENSOR_MODE_OFF,
.fs = INV_ICM42600_GYRO_FS_2000DPS,
.odr = INV_ICM42600_ODR_50HZ,
.filter = INV_ICM42600_FILTER_BW_ODR_DIV_2,
},
.accel = {
.mode = INV_ICM42600_SENSOR_MODE_OFF,
.fs = INV_ICM42600_ACCEL_FS_16G,
.odr = INV_ICM42600_ODR_50HZ,
.filter = INV_ICM42600_FILTER_BW_ODR_DIV_2,
},
.temp_en = false,
};
static const struct inv_icm42600_hw inv_icm42600_hw[INV_CHIP_NB] = {
[INV_CHIP_ICM42600] = {
.whoami = INV_ICM42600_WHOAMI_ICM42600,
.name = "icm42600",
.conf = &inv_icm42600_default_conf,
},
[INV_CHIP_ICM42602] = {
.whoami = INV_ICM42600_WHOAMI_ICM42602,
.name = "icm42602",
.conf = &inv_icm42600_default_conf,
},
[INV_CHIP_ICM42605] = {
.whoami = INV_ICM42600_WHOAMI_ICM42605,
.name = "icm42605",
.conf = &inv_icm42600_default_conf,
},
[INV_CHIP_ICM42622] = {
.whoami = INV_ICM42600_WHOAMI_ICM42622,
.name = "icm42622",
.conf = &inv_icm42600_default_conf,
},
};
const struct iio_mount_matrix *
inv_icm42600_get_mount_matrix(const struct iio_dev *indio_dev,
const struct iio_chan_spec *chan)
{
const struct inv_icm42600_state *st = iio_device_get_drvdata(indio_dev);
return &st->orientation;
}
uint32_t inv_icm42600_odr_to_period(enum inv_icm42600_odr odr)
{
static uint32_t odr_periods[INV_ICM42600_ODR_NB] = {
/* reserved values */
0, 0, 0,
/* 8kHz */
125000,
/* 4kHz */
250000,
/* 2kHz */
500000,
/* 1kHz */
1000000,
/* 200Hz */
5000000,
/* 100Hz */
10000000,
/* 50Hz */
20000000,
/* 25Hz */
40000000,
/* 12.5Hz */
80000000,
/* 6.25Hz */
160000000,
/* 3.125Hz */
320000000,
/* 1.5625Hz */
640000000,
/* 500Hz */
2000000,
};
return odr_periods[odr];
}
static int inv_icm42600_set_pwr_mgmt0(struct inv_icm42600_state *st,
enum inv_icm42600_sensor_mode gyro,
enum inv_icm42600_sensor_mode accel,
bool temp, unsigned int *sleep_ms)
{
enum inv_icm42600_sensor_mode oldgyro = st->conf.gyro.mode;
enum inv_icm42600_sensor_mode oldaccel = st->conf.accel.mode;
bool oldtemp = st->conf.temp_en;
unsigned int sleepval;
unsigned int val;
int ret;
/* if nothing changed, exit */
if (gyro == oldgyro && accel == oldaccel && temp == oldtemp)
return 0;
val = INV_ICM42600_PWR_MGMT0_GYRO(gyro) |
INV_ICM42600_PWR_MGMT0_ACCEL(accel);
if (!temp)
val |= INV_ICM42600_PWR_MGMT0_TEMP_DIS;
ret = regmap_write(st->map, INV_ICM42600_REG_PWR_MGMT0, val);
if (ret)
return ret;
st->conf.gyro.mode = gyro;
st->conf.accel.mode = accel;
st->conf.temp_en = temp;
/* compute required wait time for sensors to stabilize */
sleepval = 0;
/* temperature stabilization time */
if (temp && !oldtemp) {
if (sleepval < INV_ICM42600_TEMP_STARTUP_TIME_MS)
sleepval = INV_ICM42600_TEMP_STARTUP_TIME_MS;
}
/* accel startup time */
if (accel != oldaccel && oldaccel == INV_ICM42600_SENSOR_MODE_OFF) {
/* block any register write for at least 200 µs */
usleep_range(200, 300);
if (sleepval < INV_ICM42600_ACCEL_STARTUP_TIME_MS)
sleepval = INV_ICM42600_ACCEL_STARTUP_TIME_MS;
}
if (gyro != oldgyro) {
/* gyro startup time */
if (oldgyro == INV_ICM42600_SENSOR_MODE_OFF) {
/* block any register write for at least 200 µs */
usleep_range(200, 300);
if (sleepval < INV_ICM42600_GYRO_STARTUP_TIME_MS)
sleepval = INV_ICM42600_GYRO_STARTUP_TIME_MS;
/* gyro stop time */
} else if (gyro == INV_ICM42600_SENSOR_MODE_OFF) {
if (sleepval < INV_ICM42600_GYRO_STOP_TIME_MS)
sleepval = INV_ICM42600_GYRO_STOP_TIME_MS;
}
}
/* deferred sleep value if sleep pointer is provided or direct sleep */
if (sleep_ms)
*sleep_ms = sleepval;
else if (sleepval)
msleep(sleepval);
return 0;
}
int inv_icm42600_set_accel_conf(struct inv_icm42600_state *st,
struct inv_icm42600_sensor_conf *conf,
unsigned int *sleep_ms)
{
struct inv_icm42600_sensor_conf *oldconf = &st->conf.accel;
unsigned int val;
int ret;
/* Sanitize missing values with current values */
if (conf->mode < 0)
conf->mode = oldconf->mode;
if (conf->fs < 0)
conf->fs = oldconf->fs;
if (conf->odr < 0)
conf->odr = oldconf->odr;
if (conf->filter < 0)
conf->filter = oldconf->filter;
/* set ACCEL_CONFIG0 register (accel fullscale & odr) */
if (conf->fs != oldconf->fs || conf->odr != oldconf->odr) {
val = INV_ICM42600_ACCEL_CONFIG0_FS(conf->fs) |
INV_ICM42600_ACCEL_CONFIG0_ODR(conf->odr);
ret = regmap_write(st->map, INV_ICM42600_REG_ACCEL_CONFIG0, val);
if (ret)
return ret;
oldconf->fs = conf->fs;
oldconf->odr = conf->odr;
}
/* set GYRO_ACCEL_CONFIG0 register (accel filter) */
if (conf->filter != oldconf->filter) {
val = INV_ICM42600_GYRO_ACCEL_CONFIG0_ACCEL_FILT(conf->filter) |
INV_ICM42600_GYRO_ACCEL_CONFIG0_GYRO_FILT(st->conf.gyro.filter);
ret = regmap_write(st->map, INV_ICM42600_REG_GYRO_ACCEL_CONFIG0, val);
if (ret)
return ret;
oldconf->filter = conf->filter;
}
/* set PWR_MGMT0 register (accel sensor mode) */
return inv_icm42600_set_pwr_mgmt0(st, st->conf.gyro.mode, conf->mode,
st->conf.temp_en, sleep_ms);
}
int inv_icm42600_set_gyro_conf(struct inv_icm42600_state *st,
struct inv_icm42600_sensor_conf *conf,
unsigned int *sleep_ms)
{
struct inv_icm42600_sensor_conf *oldconf = &st->conf.gyro;
unsigned int val;
int ret;
/* sanitize missing values with current values */
if (conf->mode < 0)
conf->mode = oldconf->mode;
if (conf->fs < 0)
conf->fs = oldconf->fs;
if (conf->odr < 0)
conf->odr = oldconf->odr;
if (conf->filter < 0)
conf->filter = oldconf->filter;
/* set GYRO_CONFIG0 register (gyro fullscale & odr) */
if (conf->fs != oldconf->fs || conf->odr != oldconf->odr) {
val = INV_ICM42600_GYRO_CONFIG0_FS(conf->fs) |
INV_ICM42600_GYRO_CONFIG0_ODR(conf->odr);
ret = regmap_write(st->map, INV_ICM42600_REG_GYRO_CONFIG0, val);
if (ret)
return ret;
oldconf->fs = conf->fs;
oldconf->odr = conf->odr;
}
/* set GYRO_ACCEL_CONFIG0 register (gyro filter) */
if (conf->filter != oldconf->filter) {
val = INV_ICM42600_GYRO_ACCEL_CONFIG0_ACCEL_FILT(st->conf.accel.filter) |
INV_ICM42600_GYRO_ACCEL_CONFIG0_GYRO_FILT(conf->filter);
ret = regmap_write(st->map, INV_ICM42600_REG_GYRO_ACCEL_CONFIG0, val);
if (ret)
return ret;
oldconf->filter = conf->filter;
}
/* set PWR_MGMT0 register (gyro sensor mode) */
return inv_icm42600_set_pwr_mgmt0(st, conf->mode, st->conf.accel.mode,
st->conf.temp_en, sleep_ms);
return 0;
}
int inv_icm42600_set_temp_conf(struct inv_icm42600_state *st, bool enable,
unsigned int *sleep_ms)
{
return inv_icm42600_set_pwr_mgmt0(st, st->conf.gyro.mode,
st->conf.accel.mode, enable,
sleep_ms);
}
int inv_icm42600_debugfs_reg(struct iio_dev *indio_dev, unsigned int reg,
unsigned int writeval, unsigned int *readval)
{
struct inv_icm42600_state *st = iio_device_get_drvdata(indio_dev);
int ret;
mutex_lock(&st->lock);
if (readval)
ret = regmap_read(st->map, reg, readval);
else
ret = regmap_write(st->map, reg, writeval);
mutex_unlock(&st->lock);
return ret;
}
static int inv_icm42600_set_conf(struct inv_icm42600_state *st,
const struct inv_icm42600_conf *conf)
{
unsigned int val;
int ret;
/* set PWR_MGMT0 register (gyro & accel sensor mode, temp enabled) */
val = INV_ICM42600_PWR_MGMT0_GYRO(conf->gyro.mode) |
INV_ICM42600_PWR_MGMT0_ACCEL(conf->accel.mode);
if (!conf->temp_en)
val |= INV_ICM42600_PWR_MGMT0_TEMP_DIS;
ret = regmap_write(st->map, INV_ICM42600_REG_PWR_MGMT0, val);
if (ret)
return ret;
/* set GYRO_CONFIG0 register (gyro fullscale & odr) */
val = INV_ICM42600_GYRO_CONFIG0_FS(conf->gyro.fs) |
INV_ICM42600_GYRO_CONFIG0_ODR(conf->gyro.odr);
ret = regmap_write(st->map, INV_ICM42600_REG_GYRO_CONFIG0, val);
if (ret)
return ret;
/* set ACCEL_CONFIG0 register (accel fullscale & odr) */
val = INV_ICM42600_ACCEL_CONFIG0_FS(conf->accel.fs) |
INV_ICM42600_ACCEL_CONFIG0_ODR(conf->accel.odr);
ret = regmap_write(st->map, INV_ICM42600_REG_ACCEL_CONFIG0, val);
if (ret)
return ret;
/* set GYRO_ACCEL_CONFIG0 register (gyro & accel filters) */
val = INV_ICM42600_GYRO_ACCEL_CONFIG0_ACCEL_FILT(conf->accel.filter) |
INV_ICM42600_GYRO_ACCEL_CONFIG0_GYRO_FILT(conf->gyro.filter);
ret = regmap_write(st->map, INV_ICM42600_REG_GYRO_ACCEL_CONFIG0, val);
if (ret)
return ret;
/* update internal conf */
st->conf = *conf;
return 0;
}
/**
* inv_icm42600_setup() - check and setup chip
* @st: driver internal state
* @bus_setup: callback for setting up bus specific registers
*
* Returns 0 on success, a negative error code otherwise.
*/
static int inv_icm42600_setup(struct inv_icm42600_state *st,
inv_icm42600_bus_setup bus_setup)
{
const struct inv_icm42600_hw *hw = &inv_icm42600_hw[st->chip];
const struct device *dev = regmap_get_device(st->map);
unsigned int val;
int ret;
/* check chip self-identification value */
ret = regmap_read(st->map, INV_ICM42600_REG_WHOAMI, &val);
if (ret)
return ret;
if (val != hw->whoami) {
dev_err(dev, "invalid whoami %#02x expected %#02x (%s)\n",
val, hw->whoami, hw->name);
return -ENODEV;
}
st->name = hw->name;
/* reset to make sure previous state are not there */
ret = regmap_write(st->map, INV_ICM42600_REG_DEVICE_CONFIG,
INV_ICM42600_DEVICE_CONFIG_SOFT_RESET);
if (ret)
return ret;
msleep(INV_ICM42600_RESET_TIME_MS);
ret = regmap_read(st->map, INV_ICM42600_REG_INT_STATUS, &val);
if (ret)
return ret;
if (!(val & INV_ICM42600_INT_STATUS_RESET_DONE)) {
dev_err(dev, "reset error, reset done bit not set\n");
return -ENODEV;
}
/* set chip bus configuration */
ret = bus_setup(st);
if (ret)
return ret;
/* sensor data in big-endian (default) */
ret = regmap_update_bits(st->map, INV_ICM42600_REG_INTF_CONFIG0,
INV_ICM42600_INTF_CONFIG0_SENSOR_DATA_ENDIAN,
INV_ICM42600_INTF_CONFIG0_SENSOR_DATA_ENDIAN);
if (ret)
return ret;
return inv_icm42600_set_conf(st, hw->conf);
}
static irqreturn_t inv_icm42600_irq_timestamp(int irq, void *_data)
{
struct inv_icm42600_state *st = _data;
st->timestamp.gyro = iio_get_time_ns(st->indio_gyro);
st->timestamp.accel = iio_get_time_ns(st->indio_accel);
return IRQ_WAKE_THREAD;
}
static irqreturn_t inv_icm42600_irq_handler(int irq, void *_data)
{
struct inv_icm42600_state *st = _data;
struct device *dev = regmap_get_device(st->map);
unsigned int status;
int ret;
mutex_lock(&st->lock);
ret = regmap_read(st->map, INV_ICM42600_REG_INT_STATUS, &status);
if (ret)
goto out_unlock;
/* FIFO full */
if (status & INV_ICM42600_INT_STATUS_FIFO_FULL)
dev_warn(dev, "FIFO full data lost!\n");
/* FIFO threshold reached */
if (status & INV_ICM42600_INT_STATUS_FIFO_THS) {
ret = inv_icm42600_buffer_fifo_read(st, 0);
if (ret) {
dev_err(dev, "FIFO read error %d\n", ret);
goto out_unlock;
}
ret = inv_icm42600_buffer_fifo_parse(st);
if (ret)
dev_err(dev, "FIFO parsing error %d\n", ret);
}
out_unlock:
mutex_unlock(&st->lock);
return IRQ_HANDLED;
}
/**
* inv_icm42600_irq_init() - initialize int pin and interrupt handler
* @st: driver internal state
* @irq: irq number
* @irq_type: irq trigger type
* @open_drain: true if irq is open drain, false for push-pull
*
* Returns 0 on success, a negative error code otherwise.
*/
static int inv_icm42600_irq_init(struct inv_icm42600_state *st, int irq,
int irq_type, bool open_drain)
{
struct device *dev = regmap_get_device(st->map);
unsigned int val;
int ret;
/* configure INT1 interrupt: default is active low on edge */
switch (irq_type) {
case IRQF_TRIGGER_RISING:
case IRQF_TRIGGER_HIGH:
val = INV_ICM42600_INT_CONFIG_INT1_ACTIVE_HIGH;
break;
default:
val = INV_ICM42600_INT_CONFIG_INT1_ACTIVE_LOW;
break;
}
switch (irq_type) {
case IRQF_TRIGGER_LOW:
case IRQF_TRIGGER_HIGH:
val |= INV_ICM42600_INT_CONFIG_INT1_LATCHED;
break;
default:
break;
}
if (!open_drain)
val |= INV_ICM42600_INT_CONFIG_INT1_PUSH_PULL;
ret = regmap_write(st->map, INV_ICM42600_REG_INT_CONFIG, val);
if (ret)
return ret;
/* Deassert async reset for proper INT pin operation (cf datasheet) */
ret = regmap_update_bits(st->map, INV_ICM42600_REG_INT_CONFIG1,
INV_ICM42600_INT_CONFIG1_ASYNC_RESET, 0);
if (ret)
return ret;
return devm_request_threaded_irq(dev, irq, inv_icm42600_irq_timestamp,
inv_icm42600_irq_handler, irq_type,
"inv_icm42600", st);
}
static int inv_icm42600_enable_regulator_vddio(struct inv_icm42600_state *st)
{
int ret;
ret = regulator_enable(st->vddio_supply);
if (ret)
return ret;
/* wait a little for supply ramp */
usleep_range(3000, 4000);
return 0;
}
static void inv_icm42600_disable_vdd_reg(void *_data)
{
struct inv_icm42600_state *st = _data;
const struct device *dev = regmap_get_device(st->map);
int ret;
ret = regulator_disable(st->vdd_supply);
if (ret)
dev_err(dev, "failed to disable vdd error %d\n", ret);
}
static void inv_icm42600_disable_vddio_reg(void *_data)
{
struct inv_icm42600_state *st = _data;
const struct device *dev = regmap_get_device(st->map);
int ret;
ret = regulator_disable(st->vddio_supply);
if (ret)
dev_err(dev, "failed to disable vddio error %d\n", ret);
}
static void inv_icm42600_disable_pm(void *_data)
{
struct device *dev = _data;
pm_runtime_put_sync(dev);
pm_runtime_disable(dev);
}
int inv_icm42600_core_probe(struct regmap *regmap, int chip, int irq,
inv_icm42600_bus_setup bus_setup)
{
struct device *dev = regmap_get_device(regmap);
struct inv_icm42600_state *st;
struct irq_data *irq_desc;
int irq_type;
bool open_drain;
int ret;
if (chip < 0 || chip >= INV_CHIP_NB) {
dev_err(dev, "invalid chip = %d\n", chip);
return -ENODEV;
}
/* get irq properties, set trigger falling by default */
irq_desc = irq_get_irq_data(irq);
if (!irq_desc) {
dev_err(dev, "could not find IRQ %d\n", irq);
return -EINVAL;
}
irq_type = irqd_get_trigger_type(irq_desc);
if (!irq_type)
irq_type = IRQF_TRIGGER_FALLING;
open_drain = device_property_read_bool(dev, "drive-open-drain");
st = devm_kzalloc(dev, sizeof(*st), GFP_KERNEL);
if (!st)
return -ENOMEM;
dev_set_drvdata(dev, st);
mutex_init(&st->lock);
st->chip = chip;
st->map = regmap;
ret = iio_read_mount_matrix(dev, &st->orientation);
if (ret) {
dev_err(dev, "failed to retrieve mounting matrix %d\n", ret);
return ret;
}
st->vdd_supply = devm_regulator_get(dev, "vdd");
if (IS_ERR(st->vdd_supply))
return PTR_ERR(st->vdd_supply);
st->vddio_supply = devm_regulator_get(dev, "vddio");
if (IS_ERR(st->vddio_supply))
return PTR_ERR(st->vddio_supply);
ret = regulator_enable(st->vdd_supply);
if (ret)
return ret;
msleep(INV_ICM42600_POWER_UP_TIME_MS);
ret = devm_add_action_or_reset(dev, inv_icm42600_disable_vdd_reg, st);
if (ret)
return ret;
ret = inv_icm42600_enable_regulator_vddio(st);
if (ret)
return ret;
ret = devm_add_action_or_reset(dev, inv_icm42600_disable_vddio_reg, st);
if (ret)
return ret;
/* setup chip registers */
ret = inv_icm42600_setup(st, bus_setup);
if (ret)
return ret;
ret = inv_icm42600_timestamp_setup(st);
if (ret)
return ret;
ret = inv_icm42600_buffer_init(st);
if (ret)
return ret;
st->indio_gyro = inv_icm42600_gyro_init(st);
if (IS_ERR(st->indio_gyro))
return PTR_ERR(st->indio_gyro);
st->indio_accel = inv_icm42600_accel_init(st);
if (IS_ERR(st->indio_accel))
return PTR_ERR(st->indio_accel);
ret = inv_icm42600_irq_init(st, irq, irq_type, open_drain);
if (ret)
return ret;
/* setup runtime power management */
ret = pm_runtime_set_active(dev);
if (ret)
return ret;
pm_runtime_get_noresume(dev);
pm_runtime_enable(dev);
pm_runtime_set_autosuspend_delay(dev, INV_ICM42600_SUSPEND_DELAY_MS);
pm_runtime_use_autosuspend(dev);
pm_runtime_put(dev);
return devm_add_action_or_reset(dev, inv_icm42600_disable_pm, dev);
}
EXPORT_SYMBOL_GPL(inv_icm42600_core_probe);
/*
* Suspend saves sensors state and turns everything off.
* Check first if runtime suspend has not already done the job.
*/
static int __maybe_unused inv_icm42600_suspend(struct device *dev)
{
struct inv_icm42600_state *st = dev_get_drvdata(dev);
int ret;
mutex_lock(&st->lock);
st->suspended.gyro = st->conf.gyro.mode;
st->suspended.accel = st->conf.accel.mode;
st->suspended.temp = st->conf.temp_en;
if (pm_runtime_suspended(dev)) {
ret = 0;
goto out_unlock;
}
/* disable FIFO data streaming */
if (st->fifo.on) {
ret = regmap_write(st->map, INV_ICM42600_REG_FIFO_CONFIG,
INV_ICM42600_FIFO_CONFIG_BYPASS);
if (ret)
goto out_unlock;
}
ret = inv_icm42600_set_pwr_mgmt0(st, INV_ICM42600_SENSOR_MODE_OFF,
INV_ICM42600_SENSOR_MODE_OFF, false,
NULL);
if (ret)
goto out_unlock;
regulator_disable(st->vddio_supply);
out_unlock:
mutex_unlock(&st->lock);
return ret;
}
/*
* System resume gets the system back on and restores the sensors state.
* Manually put runtime power management in system active state.
*/
static int __maybe_unused inv_icm42600_resume(struct device *dev)
{
struct inv_icm42600_state *st = dev_get_drvdata(dev);
int ret;
mutex_lock(&st->lock);
ret = inv_icm42600_enable_regulator_vddio(st);
if (ret)
goto out_unlock;
pm_runtime_disable(dev);
pm_runtime_set_active(dev);
pm_runtime_enable(dev);
/* restore sensors state */
ret = inv_icm42600_set_pwr_mgmt0(st, st->suspended.gyro,
st->suspended.accel,
st->suspended.temp, NULL);
if (ret)
goto out_unlock;
/* restore FIFO data streaming */
if (st->fifo.on)
ret = regmap_write(st->map, INV_ICM42600_REG_FIFO_CONFIG,
INV_ICM42600_FIFO_CONFIG_STREAM);
out_unlock:
mutex_unlock(&st->lock);
return ret;
}
/* Runtime suspend will turn off sensors that are enabled by iio devices. */
static int __maybe_unused inv_icm42600_runtime_suspend(struct device *dev)
{
struct inv_icm42600_state *st = dev_get_drvdata(dev);
int ret;
mutex_lock(&st->lock);
/* disable all sensors */
ret = inv_icm42600_set_pwr_mgmt0(st, INV_ICM42600_SENSOR_MODE_OFF,
INV_ICM42600_SENSOR_MODE_OFF, false,
NULL);
if (ret)
goto error_unlock;
regulator_disable(st->vddio_supply);
error_unlock:
mutex_unlock(&st->lock);
return ret;
}
/* Sensors are enabled by iio devices, no need to turn them back on here. */
static int __maybe_unused inv_icm42600_runtime_resume(struct device *dev)
{
struct inv_icm42600_state *st = dev_get_drvdata(dev);
int ret;
mutex_lock(&st->lock);
ret = inv_icm42600_enable_regulator_vddio(st);
mutex_unlock(&st->lock);
return ret;
}
const struct dev_pm_ops inv_icm42600_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(inv_icm42600_suspend, inv_icm42600_resume)
SET_RUNTIME_PM_OPS(inv_icm42600_runtime_suspend,
inv_icm42600_runtime_resume, NULL)
};
EXPORT_SYMBOL_GPL(inv_icm42600_pm_ops);
MODULE_AUTHOR("InvenSense, Inc.");
MODULE_DESCRIPTION("InvenSense ICM-426xx device driver");
MODULE_LICENSE("GPL");