blob: 5e8ca8142482153bb3888ff0b5039778958a8bfe [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2019-20 Sean Anderson <seanga2@gmail.com>
* Copyright (C) 2020 Western Digital Corporation or its affiliates.
*/
#include <dt-bindings/clock/k210-clk.h>
#include <dt-bindings/pinctrl/k210-fpioa.h>
#include <dt-bindings/reset/k210-rst.h>
/ {
/*
* Although the K210 is a 64-bit CPU, the address bus is only 32-bits
* wide, and the upper half of all addresses is ignored.
*/
#address-cells = <1>;
#size-cells = <1>;
compatible = "canaan,kendryte-k210";
aliases {
serial0 = &uarths0;
serial1 = &uart1;
serial2 = &uart2;
serial3 = &uart3;
};
/*
* The K210 has an sv39 MMU following the privileged specification v1.9.
* Since this is a non-ratified draft specification, the kernel does not
* support it and the K210 support enabled only for the !MMU case.
* Be consistent with this by setting the CPUs MMU type to "none".
*/
cpus {
#address-cells = <1>;
#size-cells = <0>;
timebase-frequency = <7800000>;
cpu0: cpu@0 {
device_type = "cpu";
compatible = "canaan,k210", "riscv";
reg = <0>;
riscv,isa = "rv64imafdc";
mmu-type = "riscv,none";
i-cache-block-size = <64>;
i-cache-size = <0x8000>;
d-cache-block-size = <64>;
d-cache-size = <0x8000>;
cpu0_intc: interrupt-controller {
#interrupt-cells = <1>;
interrupt-controller;
compatible = "riscv,cpu-intc";
};
};
cpu1: cpu@1 {
device_type = "cpu";
compatible = "canaan,k210", "riscv";
reg = <1>;
riscv,isa = "rv64imafdc";
mmu-type = "riscv,none";
i-cache-block-size = <64>;
i-cache-size = <0x8000>;
d-cache-block-size = <64>;
d-cache-size = <0x8000>;
cpu1_intc: interrupt-controller {
#interrupt-cells = <1>;
interrupt-controller;
compatible = "riscv,cpu-intc";
};
};
};
sram: memory@80000000 {
device_type = "memory";
compatible = "canaan,k210-sram";
reg = <0x80000000 0x400000>,
<0x80400000 0x200000>,
<0x80600000 0x200000>;
reg-names = "sram0", "sram1", "aisram";
clocks = <&sysclk K210_CLK_SRAM0>,
<&sysclk K210_CLK_SRAM1>,
<&sysclk K210_CLK_AI>;
clock-names = "sram0", "sram1", "aisram";
};
clocks {
in0: oscillator {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <26000000>;
};
};
soc {
#address-cells = <1>;
#size-cells = <1>;
compatible = "simple-bus";
ranges;
interrupt-parent = <&plic0>;
rom0: nvmem@1000 {
reg = <0x1000 0x1000>;
read-only;
};
clint0: timer@2000000 {
compatible = "canaan,k210-clint", "sifive,clint0";
reg = <0x2000000 0xC000>;
interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
&cpu1_intc 3 &cpu1_intc 7>;
};
plic0: interrupt-controller@c000000 {
#interrupt-cells = <1>;
#address-cells = <0>;
compatible = "canaan,k210-plic", "sifive,plic-1.0.0";
reg = <0xC000000 0x4000000>;
interrupt-controller;
interrupts-extended = <&cpu0_intc 11 &cpu1_intc 11>;
riscv,ndev = <65>;
};
uarths0: serial@38000000 {
compatible = "canaan,k210-uarths", "sifive,uart0";
reg = <0x38000000 0x1000>;
interrupts = <33>;
clocks = <&sysclk K210_CLK_CPU>;
};
gpio0: gpio-controller@38001000 {
#interrupt-cells = <2>;
#gpio-cells = <2>;
compatible = "canaan,k210-gpiohs", "sifive,gpio0";
reg = <0x38001000 0x1000>;
interrupt-controller;
interrupts = <34 35 36 37 38 39 40 41
42 43 44 45 46 47 48 49
50 51 52 53 54 55 56 57
58 59 60 61 62 63 64 65>;
gpio-controller;
ngpios = <32>;
};
dmac0: dma-controller@50000000 {
compatible = "snps,axi-dma-1.01a";
reg = <0x50000000 0x1000>;
interrupts = <27 28 29 30 31 32>;
#dma-cells = <1>;
clocks = <&sysclk K210_CLK_DMA>, <&sysclk K210_CLK_DMA>;
clock-names = "core-clk", "cfgr-clk";
resets = <&sysrst K210_RST_DMA>;
dma-channels = <6>;
snps,dma-masters = <2>;
snps,priority = <0 1 2 3 4 5>;
snps,data-width = <5>;
snps,block-size = <0x200000 0x200000 0x200000
0x200000 0x200000 0x200000>;
snps,axi-max-burst-len = <256>;
};
apb0: bus@50200000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "simple-pm-bus";
ranges;
clocks = <&sysclk K210_CLK_APB0>;
gpio1: gpio@50200000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,dw-apb-gpio";
reg = <0x50200000 0x80>;
clocks = <&sysclk K210_CLK_APB0>,
<&sysclk K210_CLK_GPIO>;
clock-names = "bus", "db";
resets = <&sysrst K210_RST_GPIO>;
gpio1_0: gpio-port@0 {
#gpio-cells = <2>;
#interrupt-cells = <2>;
compatible = "snps,dw-apb-gpio-port";
reg = <0>;
interrupt-controller;
interrupts = <23>;
gpio-controller;
ngpios = <8>;
};
};
uart1: serial@50210000 {
compatible = "snps,dw-apb-uart";
reg = <0x50210000 0x100>;
interrupts = <11>;
clocks = <&sysclk K210_CLK_UART1>,
<&sysclk K210_CLK_APB0>;
clock-names = "baudclk", "apb_pclk";
resets = <&sysrst K210_RST_UART1>;
reg-io-width = <4>;
reg-shift = <2>;
dcd-override;
dsr-override;
cts-override;
ri-override;
};
uart2: serial@50220000 {
compatible = "snps,dw-apb-uart";
reg = <0x50220000 0x100>;
interrupts = <12>;
clocks = <&sysclk K210_CLK_UART2>,
<&sysclk K210_CLK_APB0>;
clock-names = "baudclk", "apb_pclk";
resets = <&sysrst K210_RST_UART2>;
reg-io-width = <4>;
reg-shift = <2>;
dcd-override;
dsr-override;
cts-override;
ri-override;
};
uart3: serial@50230000 {
compatible = "snps,dw-apb-uart";
reg = <0x50230000 0x100>;
interrupts = <13>;
clocks = <&sysclk K210_CLK_UART3>,
<&sysclk K210_CLK_APB0>;
clock-names = "baudclk", "apb_pclk";
resets = <&sysrst K210_RST_UART3>;
reg-io-width = <4>;
reg-shift = <2>;
dcd-override;
dsr-override;
cts-override;
ri-override;
};
spi2: spi@50240000 {
compatible = "canaan,k210-spi";
spi-slave;
reg = <0x50240000 0x100>;
#address-cells = <0>;
#size-cells = <0>;
interrupts = <3>;
clocks = <&sysclk K210_CLK_SPI2>,
<&sysclk K210_CLK_APB0>;
clock-names = "ssi_clk", "pclk";
resets = <&sysrst K210_RST_SPI2>;
spi-max-frequency = <25000000>;
};
i2s0: i2s@50250000 {
compatible = "snps,designware-i2s";
reg = <0x50250000 0x200>;
interrupts = <5>;
clocks = <&sysclk K210_CLK_I2S0>;
clock-names = "i2sclk";
resets = <&sysrst K210_RST_I2S0>;
};
i2s1: i2s@50260000 {
compatible = "snps,designware-i2s";
reg = <0x50260000 0x200>;
interrupts = <6>;
clocks = <&sysclk K210_CLK_I2S1>;
clock-names = "i2sclk";
resets = <&sysrst K210_RST_I2S1>;
};
i2s2: i2s@50270000 {
compatible = "snps,designware-i2s";
reg = <0x50270000 0x200>;
interrupts = <7>;
clocks = <&sysclk K210_CLK_I2S2>;
clock-names = "i2sclk";
resets = <&sysrst K210_RST_I2S2>;
};
i2c0: i2c@50280000 {
compatible = "snps,designware-i2c";
reg = <0x50280000 0x100>;
interrupts = <8>;
clocks = <&sysclk K210_CLK_I2C0>,
<&sysclk K210_CLK_APB0>;
clock-names = "ref", "pclk";
resets = <&sysrst K210_RST_I2C0>;
};
i2c1: i2c@50290000 {
compatible = "snps,designware-i2c";
reg = <0x50290000 0x100>;
interrupts = <9>;
clocks = <&sysclk K210_CLK_I2C1>,
<&sysclk K210_CLK_APB0>;
clock-names = "ref", "pclk";
resets = <&sysrst K210_RST_I2C1>;
};
i2c2: i2c@502a0000 {
compatible = "snps,designware-i2c";
reg = <0x502A0000 0x100>;
interrupts = <10>;
clocks = <&sysclk K210_CLK_I2C2>,
<&sysclk K210_CLK_APB0>;
clock-names = "ref", "pclk";
resets = <&sysrst K210_RST_I2C2>;
};
fpioa: pinmux@502b0000 {
compatible = "canaan,k210-fpioa";
reg = <0x502B0000 0x100>;
clocks = <&sysclk K210_CLK_FPIOA>,
<&sysclk K210_CLK_APB0>;
clock-names = "ref", "pclk";
resets = <&sysrst K210_RST_FPIOA>;
canaan,k210-sysctl-power = <&sysctl 108>;
};
timer0: timer@502d0000 {
compatible = "snps,dw-apb-timer";
reg = <0x502D0000 0x100>;
interrupts = <14 15>;
clocks = <&sysclk K210_CLK_TIMER0>,
<&sysclk K210_CLK_APB0>;
clock-names = "timer", "pclk";
resets = <&sysrst K210_RST_TIMER0>;
};
timer1: timer@502e0000 {
compatible = "snps,dw-apb-timer";
reg = <0x502E0000 0x100>;
interrupts = <16 17>;
clocks = <&sysclk K210_CLK_TIMER1>,
<&sysclk K210_CLK_APB0>;
clock-names = "timer", "pclk";
resets = <&sysrst K210_RST_TIMER1>;
};
timer2: timer@502f0000 {
compatible = "snps,dw-apb-timer";
reg = <0x502F0000 0x100>;
interrupts = <18 19>;
clocks = <&sysclk K210_CLK_TIMER2>,
<&sysclk K210_CLK_APB0>;
clock-names = "timer", "pclk";
resets = <&sysrst K210_RST_TIMER2>;
};
};
apb1: bus@50400000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "simple-pm-bus";
ranges;
clocks = <&sysclk K210_CLK_APB1>;
wdt0: watchdog@50400000 {
compatible = "snps,dw-wdt";
reg = <0x50400000 0x100>;
interrupts = <21>;
clocks = <&sysclk K210_CLK_WDT0>,
<&sysclk K210_CLK_APB1>;
clock-names = "tclk", "pclk";
resets = <&sysrst K210_RST_WDT0>;
};
wdt1: watchdog@50410000 {
compatible = "snps,dw-wdt";
reg = <0x50410000 0x100>;
interrupts = <22>;
clocks = <&sysclk K210_CLK_WDT1>,
<&sysclk K210_CLK_APB1>;
clock-names = "tclk", "pclk";
resets = <&sysrst K210_RST_WDT1>;
};
sysctl: syscon@50440000 {
compatible = "canaan,k210-sysctl",
"syscon", "simple-mfd";
reg = <0x50440000 0x100>;
clocks = <&sysclk K210_CLK_APB1>;
clock-names = "pclk";
sysclk: clock-controller {
#clock-cells = <1>;
compatible = "canaan,k210-clk";
clocks = <&in0>;
};
sysrst: reset-controller {
compatible = "canaan,k210-rst";
#reset-cells = <1>;
};
reboot: syscon-reboot {
compatible = "syscon-reboot";
regmap = <&sysctl>;
offset = <48>;
mask = <1>;
value = <1>;
};
};
};
apb2: bus@52000000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "simple-pm-bus";
ranges;
clocks = <&sysclk K210_CLK_APB2>;
spi0: spi@52000000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "canaan,k210-spi";
reg = <0x52000000 0x100>;
interrupts = <1>;
clocks = <&sysclk K210_CLK_SPI0>,
<&sysclk K210_CLK_APB2>;
clock-names = "ssi_clk", "pclk";
resets = <&sysrst K210_RST_SPI0>;
reset-names = "spi";
spi-max-frequency = <25000000>;
num-cs = <4>;
reg-io-width = <4>;
};
spi1: spi@53000000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "canaan,k210-spi";
reg = <0x53000000 0x100>;
interrupts = <2>;
clocks = <&sysclk K210_CLK_SPI1>,
<&sysclk K210_CLK_APB2>;
clock-names = "ssi_clk", "pclk";
resets = <&sysrst K210_RST_SPI1>;
reset-names = "spi";
spi-max-frequency = <25000000>;
num-cs = <4>;
reg-io-width = <4>;
};
spi3: spi@54000000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,dwc-ssi-1.01a";
reg = <0x54000000 0x200>;
interrupts = <4>;
clocks = <&sysclk K210_CLK_SPI3>,
<&sysclk K210_CLK_APB2>;
clock-names = "ssi_clk", "pclk";
resets = <&sysrst K210_RST_SPI3>;
reset-names = "spi";
/* Could possibly go up to 200 MHz */
spi-max-frequency = <100000000>;
num-cs = <4>;
reg-io-width = <4>;
};
};
};
};