blob: 0d18ed15b4032a9925660384ff9918cd3f38e76b [file] [log] [blame]
// SPDX-License-Identifier: ISC
/*
* Copyright (c) 2010 Broadcom Corporation
*/
#ifndef BRCMFMAC_SDIO_H
#define BRCMFMAC_SDIO_H
#include <linux/skbuff.h>
#include <linux/firmware.h>
#include "firmware.h"
#define SDIOD_FBR_SIZE 0x100
/* io_en */
#define SDIO_FUNC_ENABLE_1 0x02
#define SDIO_FUNC_ENABLE_2 0x04
/* io_rdys */
#define SDIO_FUNC_READY_1 0x02
#define SDIO_FUNC_READY_2 0x04
/* intr_status */
#define INTR_STATUS_FUNC1 0x2
#define INTR_STATUS_FUNC2 0x4
/* mask of register map */
#define REG_F0_REG_MASK 0x7FF
#define REG_F1_MISC_MASK 0x1FFFF
/* function 0 vendor specific CCCR registers */
#define SDIO_CCCR_BRCM_CARDCAP 0xf0
#define SDIO_CCCR_BRCM_CARDCAP_CMD14_SUPPORT BIT(1)
#define SDIO_CCCR_BRCM_CARDCAP_CMD14_EXT BIT(2)
#define SDIO_CCCR_BRCM_CARDCAP_CMD_NODEC BIT(3)
/* Interrupt enable bits for each function */
#define SDIO_CCCR_IEN_FUNC0 BIT(0)
#define SDIO_CCCR_IEN_FUNC1 BIT(1)
#define SDIO_CCCR_IEN_FUNC2 BIT(2)
#define SDIO_CCCR_BRCM_CARDCTRL 0xf1
#define SDIO_CCCR_BRCM_CARDCTRL_WLANRESET BIT(1)
#define SDIO_CCCR_BRCM_SEPINT 0xf2
#define SDIO_CCCR_BRCM_SEPINT_MASK BIT(0)
#define SDIO_CCCR_BRCM_SEPINT_OE BIT(1)
#define SDIO_CCCR_BRCM_SEPINT_ACT_HI BIT(2)
/* function 1 miscellaneous registers */
/* sprom command and status */
#define SBSDIO_SPROM_CS 0x10000
/* sprom info register */
#define SBSDIO_SPROM_INFO 0x10001
/* sprom indirect access data byte 0 */
#define SBSDIO_SPROM_DATA_LOW 0x10002
/* sprom indirect access data byte 1 */
#define SBSDIO_SPROM_DATA_HIGH 0x10003
/* sprom indirect access addr byte 0 */
#define SBSDIO_SPROM_ADDR_LOW 0x10004
/* gpio select */
#define SBSDIO_GPIO_SELECT 0x10005
/* gpio output */
#define SBSDIO_GPIO_OUT 0x10006
/* gpio enable */
#define SBSDIO_GPIO_EN 0x10007
/* rev < 7, watermark for sdio device TX path */
#define SBSDIO_WATERMARK 0x10008
/* control busy signal generation */
#define SBSDIO_DEVICE_CTL 0x10009
/* SB Address Window Low (b15) */
#define SBSDIO_FUNC1_SBADDRLOW 0x1000A
/* SB Address Window Mid (b23:b16) */
#define SBSDIO_FUNC1_SBADDRMID 0x1000B
/* SB Address Window High (b31:b24) */
#define SBSDIO_FUNC1_SBADDRHIGH 0x1000C
/* Frame Control (frame term/abort) */
#define SBSDIO_FUNC1_FRAMECTRL 0x1000D
/* ChipClockCSR (ALP/HT ctl/status) */
#define SBSDIO_FUNC1_CHIPCLKCSR 0x1000E
/* SdioPullUp (on cmd, d0-d2) */
#define SBSDIO_FUNC1_SDIOPULLUP 0x1000F
/* Write Frame Byte Count Low */
#define SBSDIO_FUNC1_WFRAMEBCLO 0x10019
/* Write Frame Byte Count High */
#define SBSDIO_FUNC1_WFRAMEBCHI 0x1001A
/* Read Frame Byte Count Low */
#define SBSDIO_FUNC1_RFRAMEBCLO 0x1001B
/* Read Frame Byte Count High */
#define SBSDIO_FUNC1_RFRAMEBCHI 0x1001C
/* MesBusyCtl (rev 11) */
#define SBSDIO_FUNC1_MESBUSYCTRL 0x1001D
/* Watermark for sdio device RX path */
#define SBSDIO_MESBUSY_RXFIFO_WM_MASK 0x7F
#define SBSDIO_MESBUSY_RXFIFO_WM_SHIFT 0
/* Enable busy capability for MES access */
#define SBSDIO_MESBUSYCTRL_ENAB 0x80
#define SBSDIO_MESBUSYCTRL_ENAB_SHIFT 7
/* Sdio Core Rev 12 */
#define SBSDIO_FUNC1_WAKEUPCTRL 0x1001E
#define SBSDIO_FUNC1_WCTRL_ALPWAIT_MASK 0x1
#define SBSDIO_FUNC1_WCTRL_ALPWAIT_SHIFT 0
#define SBSDIO_FUNC1_WCTRL_HTWAIT_MASK 0x2
#define SBSDIO_FUNC1_WCTRL_HTWAIT_SHIFT 1
#define SBSDIO_FUNC1_SLEEPCSR 0x1001F
#define SBSDIO_FUNC1_SLEEPCSR_KSO_MASK 0x1
#define SBSDIO_FUNC1_SLEEPCSR_KSO_SHIFT 0
#define SBSDIO_FUNC1_SLEEPCSR_KSO_EN 1
#define SBSDIO_FUNC1_SLEEPCSR_DEVON_MASK 0x2
#define SBSDIO_FUNC1_SLEEPCSR_DEVON_SHIFT 1
#define SBSDIO_FUNC1_MISC_REG_START 0x10000 /* f1 misc register start */
#define SBSDIO_FUNC1_MISC_REG_LIMIT 0x1001F /* f1 misc register end */
/* function 1 OCP space */
/* sb offset addr is <= 15 bits, 32k */
#define SBSDIO_SB_OFT_ADDR_MASK 0x07FFF
#define SBSDIO_SB_OFT_ADDR_LIMIT 0x08000
/* with b15, maps to 32-bit SB access */
#define SBSDIO_SB_ACCESS_2_4B_FLAG 0x08000
/* Address bits from SBADDR regs */
#define SBSDIO_SBWINDOW_MASK 0xffff8000
#define SDIOH_READ 0 /* Read request */
#define SDIOH_WRITE 1 /* Write request */
#define SDIOH_DATA_FIX 0 /* Fixed addressing */
#define SDIOH_DATA_INC 1 /* Incremental addressing */
/* internal return code */
#define SUCCESS 0
#define ERROR 1
/* Packet alignment for most efficient SDIO (can change based on platform) */
#define BRCMF_SDALIGN (1 << 6)
/* watchdog polling interval */
#define BRCMF_WD_POLL msecs_to_jiffies(10)
/**
* enum brcmf_sdiod_state - the state of the bus.
*
* @BRCMF_SDIOD_DOWN: Device can be accessed, no DPC.
* @BRCMF_SDIOD_DATA: Ready for data transfers, DPC enabled.
* @BRCMF_SDIOD_NOMEDIUM: No medium access to dongle possible.
*/
enum brcmf_sdiod_state {
BRCMF_SDIOD_DOWN,
BRCMF_SDIOD_DATA,
BRCMF_SDIOD_NOMEDIUM
};
struct brcmf_sdreg {
int func;
int offset;
int value;
};
struct brcmf_sdio;
struct brcmf_sdiod_freezer;
struct brcmf_sdio_dev {
struct sdio_func *func1;
struct sdio_func *func2;
u32 sbwad; /* Save backplane window address */
struct brcmf_core *cc_core; /* chipcommon core info struct */
struct brcmf_sdio *bus;
struct device *dev;
struct brcmf_bus *bus_if;
struct brcmf_mp_device *settings;
bool oob_irq_requested;
bool sd_irq_requested;
bool irq_en; /* irq enable flags */
spinlock_t irq_en_lock;
bool sg_support;
uint max_request_size;
ushort max_segment_count;
uint max_segment_size;
uint txglomsz;
struct sg_table sgtable;
char fw_name[BRCMF_FW_NAME_LEN];
char nvram_name[BRCMF_FW_NAME_LEN];
char clm_name[BRCMF_FW_NAME_LEN];
bool wowl_enabled;
bool func1_power_manageable;
bool func2_power_manageable;
enum brcmf_sdiod_state state;
struct brcmf_sdiod_freezer *freezer;
const struct firmware *clm_fw;
};
/* sdio core registers */
struct sdpcmd_regs {
u32 corecontrol; /* 0x00, rev8 */
u32 corestatus; /* rev8 */
u32 PAD[1];
u32 biststatus; /* rev8 */
/* PCMCIA access */
u16 pcmciamesportaladdr; /* 0x010, rev8 */
u16 PAD[1];
u16 pcmciamesportalmask; /* rev8 */
u16 PAD[1];
u16 pcmciawrframebc; /* rev8 */
u16 PAD[1];
u16 pcmciaunderflowtimer; /* rev8 */
u16 PAD[1];
/* interrupt */
u32 intstatus; /* 0x020, rev8 */
u32 hostintmask; /* rev8 */
u32 intmask; /* rev8 */
u32 sbintstatus; /* rev8 */
u32 sbintmask; /* rev8 */
u32 funcintmask; /* rev4 */
u32 PAD[2];
u32 tosbmailbox; /* 0x040, rev8 */
u32 tohostmailbox; /* rev8 */
u32 tosbmailboxdata; /* rev8 */
u32 tohostmailboxdata; /* rev8 */
/* synchronized access to registers in SDIO clock domain */
u32 sdioaccess; /* 0x050, rev8 */
u32 PAD[3];
/* PCMCIA frame control */
u8 pcmciaframectrl; /* 0x060, rev8 */
u8 PAD[3];
u8 pcmciawatermark; /* rev8 */
u8 PAD[155];
/* interrupt batching control */
u32 intrcvlazy; /* 0x100, rev8 */
u32 PAD[3];
/* counters */
u32 cmd52rd; /* 0x110, rev8 */
u32 cmd52wr; /* rev8 */
u32 cmd53rd; /* rev8 */
u32 cmd53wr; /* rev8 */
u32 abort; /* rev8 */
u32 datacrcerror; /* rev8 */
u32 rdoutofsync; /* rev8 */
u32 wroutofsync; /* rev8 */
u32 writebusy; /* rev8 */
u32 readwait; /* rev8 */
u32 readterm; /* rev8 */
u32 writeterm; /* rev8 */
u32 PAD[40];
u32 clockctlstatus; /* rev8 */
u32 PAD[7];
u32 PAD[128]; /* DMA engines */
/* SDIO/PCMCIA CIS region */
char cis[512]; /* 0x400-0x5ff, rev6 */
/* PCMCIA function control registers */
char pcmciafcr[256]; /* 0x600-6ff, rev6 */
u16 PAD[55];
/* PCMCIA backplane access */
u16 backplanecsr; /* 0x76E, rev6 */
u16 backplaneaddr0; /* rev6 */
u16 backplaneaddr1; /* rev6 */
u16 backplaneaddr2; /* rev6 */
u16 backplaneaddr3; /* rev6 */
u16 backplanedata0; /* rev6 */
u16 backplanedata1; /* rev6 */
u16 backplanedata2; /* rev6 */
u16 backplanedata3; /* rev6 */
u16 PAD[31];
/* sprom "size" & "blank" info */
u16 spromstatus; /* 0x7BE, rev2 */
u32 PAD[464];
u16 PAD[0x80];
};
/* Register/deregister interrupt handler. */
int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev);
void brcmf_sdiod_intr_unregister(struct brcmf_sdio_dev *sdiodev);
/* SDIO device register access interface */
/* Accessors for SDIO Function 0 */
#define brcmf_sdiod_func0_rb(sdiodev, addr, r) \
sdio_f0_readb((sdiodev)->func1, (addr), (r))
#define brcmf_sdiod_func0_wb(sdiodev, addr, v, ret) \
sdio_f0_writeb((sdiodev)->func1, (v), (addr), (ret))
/* Accessors for SDIO Function 1 */
#define brcmf_sdiod_readb(sdiodev, addr, r) \
sdio_readb((sdiodev)->func1, (addr), (r))
#define brcmf_sdiod_writeb(sdiodev, addr, v, ret) \
sdio_writeb((sdiodev)->func1, (v), (addr), (ret))
u32 brcmf_sdiod_readl(struct brcmf_sdio_dev *sdiodev, u32 addr, int *ret);
void brcmf_sdiod_writel(struct brcmf_sdio_dev *sdiodev, u32 addr, u32 data,
int *ret);
/* Buffer transfer to/from device (client) core via cmd53.
* fn: function number
* flags: backplane width, address increment, sync/async
* buf: pointer to memory data buffer
* nbytes: number of bytes to transfer to/from buf
* pkt: pointer to packet associated with buf (if any)
* complete: callback function for command completion (async only)
* handle: handle for completion callback (first arg in callback)
* Returns 0 or error code.
* NOTE: Async operation is not currently supported.
*/
int brcmf_sdiod_send_pkt(struct brcmf_sdio_dev *sdiodev,
struct sk_buff_head *pktq);
int brcmf_sdiod_send_buf(struct brcmf_sdio_dev *sdiodev, u8 *buf, uint nbytes);
int brcmf_sdiod_recv_pkt(struct brcmf_sdio_dev *sdiodev, struct sk_buff *pkt);
int brcmf_sdiod_recv_buf(struct brcmf_sdio_dev *sdiodev, u8 *buf, uint nbytes);
int brcmf_sdiod_recv_chain(struct brcmf_sdio_dev *sdiodev,
struct sk_buff_head *pktq, uint totlen);
/* Flags bits */
/* Four-byte target (backplane) width (vs. two-byte) */
#define SDIO_REQ_4BYTE 0x1
/* Fixed address (FIFO) (vs. incrementing address) */
#define SDIO_REQ_FIXED 0x2
/* Read/write to memory block (F1, no FIFO) via CMD53 (sync only).
* rw: read or write (0/1)
* addr: direct SDIO address
* buf: pointer to memory data buffer
* nbytes: number of bytes to transfer to/from buf
* Returns 0 or error code.
*/
int brcmf_sdiod_ramrw(struct brcmf_sdio_dev *sdiodev, bool write, u32 address,
u8 *data, uint size);
/* Issue an abort to the specified function */
int brcmf_sdiod_abort(struct brcmf_sdio_dev *sdiodev, struct sdio_func *func);
void brcmf_sdiod_sgtable_alloc(struct brcmf_sdio_dev *sdiodev);
void brcmf_sdiod_change_state(struct brcmf_sdio_dev *sdiodev,
enum brcmf_sdiod_state state);
bool brcmf_sdiod_freezing(struct brcmf_sdio_dev *sdiodev);
void brcmf_sdiod_try_freeze(struct brcmf_sdio_dev *sdiodev);
void brcmf_sdiod_freezer_count(struct brcmf_sdio_dev *sdiodev);
void brcmf_sdiod_freezer_uncount(struct brcmf_sdio_dev *sdiodev);
int brcmf_sdiod_probe(struct brcmf_sdio_dev *sdiodev);
int brcmf_sdiod_remove(struct brcmf_sdio_dev *sdiodev);
struct brcmf_sdio *brcmf_sdio_probe(struct brcmf_sdio_dev *sdiodev);
void brcmf_sdio_remove(struct brcmf_sdio *bus);
void brcmf_sdio_isr(struct brcmf_sdio *bus, bool in_isr);
void brcmf_sdio_wd_timer(struct brcmf_sdio *bus, bool active);
void brcmf_sdio_wowl_config(struct device *dev, bool enabled);
int brcmf_sdio_sleep(struct brcmf_sdio *bus, bool sleep);
void brcmf_sdio_trigger_dpc(struct brcmf_sdio *bus);
#endif /* BRCMFMAC_SDIO_H */