| /* |
| * Copyright (C) 2014 STMicroelectronics Limited. |
| * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * publishhed by the Free Software Foundation. |
| */ |
| #include "stih407-pinctrl.dtsi" |
| #include <dt-bindings/mfd/st-lpc.h> |
| #include <dt-bindings/phy/phy.h> |
| #include <dt-bindings/reset/stih407-resets.h> |
| #include <dt-bindings/interrupt-controller/irq-st.h> |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gp0_reserved: rproc@40000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x40000000 0x01000000>; |
| no-map; |
| status = "disabled"; |
| }; |
| |
| gp1_reserved: rproc@41000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x41000000 0x01000000>; |
| no-map; |
| status = "disabled"; |
| }; |
| |
| audio_reserved: rproc@42000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x42000000 0x01000000>; |
| no-map; |
| status = "disabled"; |
| }; |
| |
| dmu_reserved: rproc@43000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x43000000 0x01000000>; |
| no-map; |
| }; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| reg = <0>; |
| |
| /* u-boot puts hpen in SBC dmem at 0xa4 offset */ |
| cpu-release-addr = <0x94100A4>; |
| |
| /* kHz uV */ |
| operating-points = <1500000 0 |
| 1200000 0 |
| 800000 0 |
| 500000 0>; |
| |
| clocks = <&clk_m_a9>; |
| clock-names = "cpu"; |
| clock-latency = <100000>; |
| cpu0-supply = <&pwm_regulator>; |
| st,syscfg = <&syscfg_core 0x8e0>; |
| }; |
| cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| reg = <1>; |
| |
| /* u-boot puts hpen in SBC dmem at 0xa4 offset */ |
| cpu-release-addr = <0x94100A4>; |
| |
| /* kHz uV */ |
| operating-points = <1500000 0 |
| 1200000 0 |
| 800000 0 |
| 500000 0>; |
| }; |
| }; |
| |
| intc: interrupt-controller@08761000 { |
| compatible = "arm,cortex-a9-gic"; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0x08761000 0x1000>, <0x08760100 0x100>; |
| }; |
| |
| scu@08760000 { |
| compatible = "arm,cortex-a9-scu"; |
| reg = <0x08760000 0x1000>; |
| }; |
| |
| timer@08760200 { |
| interrupt-parent = <&intc>; |
| compatible = "arm,cortex-a9-global-timer"; |
| reg = <0x08760200 0x100>; |
| interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&arm_periph_clk>; |
| }; |
| |
| l2: cache-controller { |
| compatible = "arm,pl310-cache"; |
| reg = <0x08762000 0x1000>; |
| arm,data-latency = <3 3 3>; |
| arm,tag-latency = <2 2 2>; |
| cache-unified; |
| cache-level = <2>; |
| }; |
| |
| arm-pmu { |
| interrupt-parent = <&intc>; |
| compatible = "arm,cortex-a9-pmu"; |
| interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| pwm_regulator: pwm-regulator { |
| compatible = "pwm-regulator"; |
| pwms = <&pwm1 3 8448>; |
| regulator-name = "CPU_1V0_AVS"; |
| regulator-min-microvolt = <784000>; |
| regulator-max-microvolt = <1299000>; |
| regulator-always-on; |
| max-duty-cycle = <255>; |
| status = "okay"; |
| }; |
| |
| soc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| interrupt-parent = <&intc>; |
| ranges; |
| compatible = "simple-bus"; |
| |
| restart { |
| compatible = "st,stih407-restart"; |
| st,syscfg = <&syscfg_sbc_reg>; |
| status = "okay"; |
| }; |
| |
| powerdown: powerdown-controller { |
| compatible = "st,stih407-powerdown"; |
| #reset-cells = <1>; |
| }; |
| |
| softreset: softreset-controller { |
| compatible = "st,stih407-softreset"; |
| #reset-cells = <1>; |
| }; |
| |
| picophyreset: picophyreset-controller { |
| compatible = "st,stih407-picophyreset"; |
| #reset-cells = <1>; |
| }; |
| |
| syscfg_sbc: sbc-syscfg@9620000 { |
| compatible = "st,stih407-sbc-syscfg", "syscon"; |
| reg = <0x9620000 0x1000>; |
| }; |
| |
| syscfg_front: front-syscfg@9280000 { |
| compatible = "st,stih407-front-syscfg", "syscon"; |
| reg = <0x9280000 0x1000>; |
| }; |
| |
| syscfg_rear: rear-syscfg@9290000 { |
| compatible = "st,stih407-rear-syscfg", "syscon"; |
| reg = <0x9290000 0x1000>; |
| }; |
| |
| syscfg_flash: flash-syscfg@92a0000 { |
| compatible = "st,stih407-flash-syscfg", "syscon"; |
| reg = <0x92a0000 0x1000>; |
| }; |
| |
| syscfg_sbc_reg: fvdp-lite-syscfg@9600000 { |
| compatible = "st,stih407-sbc-reg-syscfg", "syscon"; |
| reg = <0x9600000 0x1000>; |
| }; |
| |
| syscfg_core: core-syscfg@92b0000 { |
| compatible = "st,stih407-core-syscfg", "syscon"; |
| reg = <0x92b0000 0x1000>; |
| }; |
| |
| syscfg_lpm: lpm-syscfg@94b5100 { |
| compatible = "st,stih407-lpm-syscfg", "syscon"; |
| reg = <0x94b5100 0x1000>; |
| }; |
| |
| irq-syscfg { |
| compatible = "st,stih407-irq-syscfg"; |
| st,syscfg = <&syscfg_core>; |
| st,irq-device = <ST_IRQ_SYSCFG_PMU_0>, |
| <ST_IRQ_SYSCFG_PMU_1>; |
| st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>, |
| <ST_IRQ_SYSCFG_DISABLED>; |
| }; |
| |
| /* Display */ |
| vtg_main: sti-vtg-main@8d02800 { |
| compatible = "st,vtg"; |
| reg = <0x8d02800 0x200>; |
| interrupts = <GIC_SPI 108 IRQ_TYPE_NONE>; |
| }; |
| |
| vtg_aux: sti-vtg-aux@8d00200 { |
| compatible = "st,vtg"; |
| reg = <0x8d00200 0x100>; |
| interrupts = <GIC_SPI 109 IRQ_TYPE_NONE>; |
| }; |
| |
| serial@9830000 { |
| compatible = "st,asc"; |
| reg = <0x9830000 0x2c>; |
| interrupts = <GIC_SPI 122 IRQ_TYPE_NONE>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_serial0>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| |
| status = "disabled"; |
| }; |
| |
| serial@9831000 { |
| compatible = "st,asc"; |
| reg = <0x9831000 0x2c>; |
| interrupts = <GIC_SPI 123 IRQ_TYPE_NONE>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_serial1>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| |
| status = "disabled"; |
| }; |
| |
| serial@9832000 { |
| compatible = "st,asc"; |
| reg = <0x9832000 0x2c>; |
| interrupts = <GIC_SPI 124 IRQ_TYPE_NONE>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_serial2>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| |
| status = "disabled"; |
| }; |
| |
| /* SBC_ASC0 - UART10 */ |
| sbc_serial0: serial@9530000 { |
| compatible = "st,asc"; |
| reg = <0x9530000 0x2c>; |
| interrupts = <GIC_SPI 138 IRQ_TYPE_NONE>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sbc_serial0>; |
| clocks = <&clk_sysin>; |
| |
| status = "disabled"; |
| }; |
| |
| serial@9531000 { |
| compatible = "st,asc"; |
| reg = <0x9531000 0x2c>; |
| interrupts = <GIC_SPI 139 IRQ_TYPE_NONE>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sbc_serial1>; |
| clocks = <&clk_sysin>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c@9840000 { |
| compatible = "st,comms-ssc4-i2c"; |
| interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x9840000 0x110>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| clock-names = "ssc"; |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c0_default>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c@9841000 { |
| compatible = "st,comms-ssc4-i2c"; |
| reg = <0x9841000 0x110>; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| clock-names = "ssc"; |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1_default>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c@9842000 { |
| compatible = "st,comms-ssc4-i2c"; |
| reg = <0x9842000 0x110>; |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| clock-names = "ssc"; |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2_default>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c@9843000 { |
| compatible = "st,comms-ssc4-i2c"; |
| reg = <0x9843000 0x110>; |
| interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| clock-names = "ssc"; |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3_default>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c@9844000 { |
| compatible = "st,comms-ssc4-i2c"; |
| reg = <0x9844000 0x110>; |
| interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| clock-names = "ssc"; |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c4_default>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c@9845000 { |
| compatible = "st,comms-ssc4-i2c"; |
| reg = <0x9845000 0x110>; |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| clock-names = "ssc"; |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c5_default>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| |
| /* SSCs on SBC */ |
| i2c@9540000 { |
| compatible = "st,comms-ssc4-i2c"; |
| reg = <0x9540000 0x110>; |
| interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_sysin>; |
| clock-names = "ssc"; |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c10_default>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c@9541000 { |
| compatible = "st,comms-ssc4-i2c"; |
| reg = <0x9541000 0x110>; |
| interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_sysin>; |
| clock-names = "ssc"; |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c11_default>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| usb2_picophy0: phy1 { |
| compatible = "st,stih407-usb2-phy"; |
| #phy-cells = <0>; |
| st,syscfg = <&syscfg_core 0x100 0xf4>; |
| resets = <&softreset STIH407_PICOPHY_SOFTRESET>, |
| <&picophyreset STIH407_PICOPHY2_RESET>; |
| reset-names = "global", "port"; |
| }; |
| |
| miphy28lp_phy: miphy28lp@9b22000 { |
| compatible = "st,miphy28lp-phy"; |
| st,syscfg = <&syscfg_core>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| phy_port0: port@9b22000 { |
| reg = <0x9b22000 0xff>, |
| <0x9b09000 0xff>, |
| <0x9b04000 0xff>; |
| reg-names = "sata-up", |
| "pcie-up", |
| "pipew"; |
| |
| st,syscfg = <0x114 0x818 0xe0 0xec>; |
| #phy-cells = <1>; |
| |
| reset-names = "miphy-sw-rst"; |
| resets = <&softreset STIH407_MIPHY0_SOFTRESET>; |
| }; |
| |
| phy_port1: port@9b2a000 { |
| reg = <0x9b2a000 0xff>, |
| <0x9b19000 0xff>, |
| <0x9b14000 0xff>; |
| reg-names = "sata-up", |
| "pcie-up", |
| "pipew"; |
| |
| st,syscfg = <0x118 0x81c 0xe4 0xf0>; |
| |
| #phy-cells = <1>; |
| |
| reset-names = "miphy-sw-rst"; |
| resets = <&softreset STIH407_MIPHY1_SOFTRESET>; |
| }; |
| |
| phy_port2: port@8f95000 { |
| reg = <0x8f95000 0xff>, |
| <0x8f90000 0xff>; |
| reg-names = "pipew", |
| "usb3-up"; |
| |
| st,syscfg = <0x11c 0x820>; |
| |
| #phy-cells = <1>; |
| |
| reset-names = "miphy-sw-rst"; |
| resets = <&softreset STIH407_MIPHY2_SOFTRESET>; |
| }; |
| }; |
| |
| spi@9840000 { |
| compatible = "st,comms-ssc4-spi"; |
| reg = <0x9840000 0x110>; |
| interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| clock-names = "ssc"; |
| pinctrl-0 = <&pinctrl_spi0_default>; |
| pinctrl-names = "default"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi@9841000 { |
| compatible = "st,comms-ssc4-spi"; |
| reg = <0x9841000 0x110>; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| clock-names = "ssc"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi1_default>; |
| |
| status = "disabled"; |
| }; |
| |
| spi@9842000 { |
| compatible = "st,comms-ssc4-spi"; |
| reg = <0x9842000 0x110>; |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| clock-names = "ssc"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi2_default>; |
| |
| status = "disabled"; |
| }; |
| |
| spi@9843000 { |
| compatible = "st,comms-ssc4-spi"; |
| reg = <0x9843000 0x110>; |
| interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| clock-names = "ssc"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi3_default>; |
| |
| status = "disabled"; |
| }; |
| |
| spi@9844000 { |
| compatible = "st,comms-ssc4-spi"; |
| reg = <0x9844000 0x110>; |
| interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| clock-names = "ssc"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi4_default>; |
| |
| status = "disabled"; |
| }; |
| |
| /* SBC SSC */ |
| spi@9540000 { |
| compatible = "st,comms-ssc4-spi"; |
| reg = <0x9540000 0x110>; |
| interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_sysin>; |
| clock-names = "ssc"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi10_default>; |
| |
| status = "disabled"; |
| }; |
| |
| spi@9541000 { |
| compatible = "st,comms-ssc4-spi"; |
| reg = <0x9541000 0x110>; |
| interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_sysin>; |
| clock-names = "ssc"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi11_default>; |
| |
| status = "disabled"; |
| }; |
| |
| spi@9542000 { |
| compatible = "st,comms-ssc4-spi"; |
| reg = <0x9542000 0x110>; |
| interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk_sysin>; |
| clock-names = "ssc"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi12_default>; |
| |
| status = "disabled"; |
| }; |
| |
| mmc0: sdhci@09060000 { |
| compatible = "st,sdhci-stih407", "st,sdhci"; |
| status = "disabled"; |
| reg = <0x09060000 0x7ff>, <0x9061008 0x20>; |
| reg-names = "mmc", "top-mmc-delay"; |
| interrupts = <GIC_SPI 92 IRQ_TYPE_NONE>; |
| interrupt-names = "mmcirq"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mmc0>; |
| clock-names = "mmc", "icn"; |
| clocks = <&clk_s_c0_flexgen CLK_MMC_0>, |
| <&clk_s_c0_flexgen CLK_RX_ICN_HVA>; |
| bus-width = <8>; |
| }; |
| |
| mmc1: sdhci@09080000 { |
| compatible = "st,sdhci-stih407", "st,sdhci"; |
| status = "disabled"; |
| reg = <0x09080000 0x7ff>; |
| reg-names = "mmc"; |
| interrupts = <GIC_SPI 90 IRQ_TYPE_NONE>; |
| interrupt-names = "mmcirq"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sd1>; |
| clock-names = "mmc", "icn"; |
| clocks = <&clk_s_c0_flexgen CLK_MMC_1>, |
| <&clk_s_c0_flexgen CLK_RX_ICN_HVA>; |
| resets = <&softreset STIH407_MMC1_SOFTRESET>; |
| bus-width = <4>; |
| }; |
| |
| /* Watchdog and Real-Time Clock */ |
| lpc@8787000 { |
| compatible = "st,stih407-lpc"; |
| reg = <0x8787000 0x1000>; |
| interrupts = <GIC_SPI 129 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&clk_s_d3_flexgen CLK_LPC_0>; |
| timeout-sec = <120>; |
| st,syscfg = <&syscfg_core>; |
| st,lpc-mode = <ST_LPC_MODE_WDT>; |
| }; |
| |
| lpc@8788000 { |
| compatible = "st,stih407-lpc"; |
| reg = <0x8788000 0x1000>; |
| interrupts = <GIC_SPI 130 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&clk_s_d3_flexgen CLK_LPC_1>; |
| st,lpc-mode = <ST_LPC_MODE_CLKSRC>; |
| }; |
| |
| sata0: sata@9b20000 { |
| compatible = "st,ahci"; |
| reg = <0x9b20000 0x1000>; |
| |
| interrupts = <GIC_SPI 159 IRQ_TYPE_NONE>; |
| interrupt-names = "hostc"; |
| |
| phys = <&phy_port0 PHY_TYPE_SATA>; |
| phy-names = "ahci_phy"; |
| |
| resets = <&powerdown STIH407_SATA0_POWERDOWN>, |
| <&softreset STIH407_SATA0_SOFTRESET>, |
| <&softreset STIH407_SATA0_PWR_SOFTRESET>; |
| reset-names = "pwr-dwn", "sw-rst", "pwr-rst"; |
| |
| clock-names = "ahci_clk"; |
| clocks = <&clk_s_c0_flexgen CLK_ICN_REG>; |
| |
| ports-implemented = <0x1>; |
| |
| status = "disabled"; |
| }; |
| |
| sata1: sata@9b28000 { |
| compatible = "st,ahci"; |
| reg = <0x9b28000 0x1000>; |
| |
| interrupts = <GIC_SPI 170 IRQ_TYPE_NONE>; |
| interrupt-names = "hostc"; |
| |
| phys = <&phy_port1 PHY_TYPE_SATA>; |
| phy-names = "ahci_phy"; |
| |
| resets = <&powerdown STIH407_SATA1_POWERDOWN>, |
| <&softreset STIH407_SATA1_SOFTRESET>, |
| <&softreset STIH407_SATA1_PWR_SOFTRESET>; |
| reset-names = "pwr-dwn", |
| "sw-rst", |
| "pwr-rst"; |
| |
| clock-names = "ahci_clk"; |
| clocks = <&clk_s_c0_flexgen CLK_ICN_REG>; |
| |
| ports-implemented = <0x1>; |
| |
| status = "disabled"; |
| }; |
| |
| |
| st_dwc3: dwc3@8f94000 { |
| compatible = "st,stih407-dwc3"; |
| reg = <0x08f94000 0x1000>, <0x110 0x4>; |
| reg-names = "reg-glue", "syscfg-reg"; |
| st,syscfg = <&syscfg_core>; |
| resets = <&powerdown STIH407_USB3_POWERDOWN>, |
| <&softreset STIH407_MIPHY2_SOFTRESET>; |
| reset-names = "powerdown", "softreset"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb3>; |
| ranges; |
| |
| status = "disabled"; |
| |
| dwc3: dwc3@9900000 { |
| compatible = "snps,dwc3"; |
| reg = <0x09900000 0x100000>; |
| interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>; |
| dr_mode = "host"; |
| phy-names = "usb2-phy", "usb3-phy"; |
| phys = <&usb2_picophy0>, |
| <&phy_port2 PHY_TYPE_USB3>; |
| }; |
| }; |
| |
| /* COMMS PWM Module */ |
| pwm0: pwm@9810000 { |
| compatible = "st,sti-pwm"; |
| #pwm-cells = <2>; |
| reg = <0x9810000 0x68>; |
| interrupts = <GIC_SPI 128 IRQ_TYPE_NONE>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm0_chan0_default>; |
| clock-names = "pwm"; |
| clocks = <&clk_sysin>; |
| st,pwm-num-chan = <1>; |
| |
| status = "disabled"; |
| }; |
| |
| /* SBC PWM Module */ |
| pwm1: pwm@9510000 { |
| compatible = "st,sti-pwm"; |
| #pwm-cells = <2>; |
| reg = <0x9510000 0x68>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm1_chan0_default |
| &pinctrl_pwm1_chan1_default |
| &pinctrl_pwm1_chan2_default |
| &pinctrl_pwm1_chan3_default>; |
| clock-names = "pwm"; |
| clocks = <&clk_sysin>; |
| st,pwm-num-chan = <4>; |
| |
| status = "disabled"; |
| }; |
| |
| rng10: rng@08a89000 { |
| compatible = "st,rng"; |
| reg = <0x08a89000 0x1000>; |
| clocks = <&clk_sysin>; |
| status = "okay"; |
| }; |
| |
| rng11: rng@08a8a000 { |
| compatible = "st,rng"; |
| reg = <0x08a8a000 0x1000>; |
| clocks = <&clk_sysin>; |
| status = "okay"; |
| }; |
| |
| ethernet0: dwmac@9630000 { |
| device_type = "network"; |
| status = "disabled"; |
| compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710"; |
| reg = <0x9630000 0x8000>, <0x80 0x4>; |
| reg-names = "stmmaceth", "sti-ethconf"; |
| |
| st,syscon = <&syscfg_sbc_reg 0x80>; |
| st,gmac_en; |
| resets = <&softreset STIH407_ETH1_SOFTRESET>; |
| reset-names = "stmmaceth"; |
| |
| interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>, |
| <GIC_SPI 99 IRQ_TYPE_NONE>; |
| interrupt-names = "macirq", "eth_wake_irq"; |
| |
| /* DMA Bus Mode */ |
| snps,pbl = <8>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_rgmii1>; |
| |
| clock-names = "stmmaceth", "sti-ethclk"; |
| clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>, |
| <&clk_s_c0_flexgen CLK_ETH_PHY>; |
| }; |
| |
| cec: sti-cec@094a087c { |
| compatible = "st,stih-cec"; |
| reg = <0x94a087c 0x64>; |
| clocks = <&clk_sysin>; |
| clock-names = "cec-clk"; |
| interrupts = <GIC_SPI 140 IRQ_TYPE_NONE>; |
| interrupt-names = "cec-irq"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cec0_default>; |
| resets = <&softreset STIH407_LPM_SOFTRESET>; |
| }; |
| |
| rng10: rng@08a89000 { |
| compatible = "st,rng"; |
| reg = <0x08a89000 0x1000>; |
| clocks = <&clk_sysin>; |
| status = "okay"; |
| }; |
| |
| rng11: rng@08a8a000 { |
| compatible = "st,rng"; |
| reg = <0x08a8a000 0x1000>; |
| clocks = <&clk_sysin>; |
| status = "okay"; |
| }; |
| |
| mailbox0: mailbox@8f00000 { |
| compatible = "st,stih407-mailbox"; |
| reg = <0x8f00000 0x1000>; |
| interrupts = <GIC_SPI 1 IRQ_TYPE_NONE>; |
| #mbox-cells = <2>; |
| mbox-name = "a9"; |
| status = "okay"; |
| }; |
| |
| mailbox1: mailbox@8f01000 { |
| compatible = "st,stih407-mailbox"; |
| reg = <0x8f01000 0x1000>; |
| #mbox-cells = <2>; |
| mbox-name = "st231_gp_1"; |
| status = "okay"; |
| }; |
| |
| mailbox2: mailbox@8f02000 { |
| compatible = "st,stih407-mailbox"; |
| reg = <0x8f02000 0x1000>; |
| #mbox-cells = <2>; |
| mbox-name = "st231_gp_0"; |
| status = "okay"; |
| }; |
| |
| mailbox3: mailbox@8f03000 { |
| compatible = "st,stih407-mailbox"; |
| reg = <0x8f03000 0x1000>; |
| #mbox-cells = <2>; |
| mbox-name = "st231_audio_video"; |
| status = "okay"; |
| }; |
| |
| st231_gp0: remote-processor { |
| compatible = "st,st231-rproc"; |
| memory-region = <&gp0_reserved>; |
| resets = <&softreset STIH407_ST231_GP0_SOFTRESET>; |
| reset-names = "sw_reset"; |
| clocks = <&clk_s_c0_flexgen CLK_ST231_GP_0>; |
| clock-frequency = <600000000>; |
| st,syscfg = <&syscfg_core 0x22c>; |
| }; |
| |
| |
| st231_gp1: remote-processor { |
| compatible = "st,st231-rproc"; |
| memory-region = <&gp1_reserved>; |
| resets = <&softreset STIH407_ST231_GP1_SOFTRESET>; |
| reset-names = "sw_reset"; |
| clocks = <&clk_s_c0_flexgen CLK_ST231_GP_1>; |
| clock-frequency = <600000000>; |
| st,syscfg = <&syscfg_core 0x220>; |
| }; |
| |
| st231_audio: remote-processor { |
| compatible = "st,st231-rproc"; |
| memory-region = <&audio_reserved>; |
| resets = <&softreset STIH407_ST231_AUD_SOFTRESET>; |
| reset-names = "sw_reset"; |
| clocks = <&clk_s_c0_flexgen CLK_ST231_AUD_0>; |
| clock-frequency = <600000000>; |
| st,syscfg = <&syscfg_core 0x228>; |
| }; |
| |
| st231_dmu: remote-processor { |
| compatible = "st,st231-rproc"; |
| memory-region = <&dmu_reserved>; |
| resets = <&softreset STIH407_ST231_DMU_SOFTRESET>; |
| reset-names = "sw_reset"; |
| clocks = <&clk_s_c0_flexgen CLK_ST231_DMU>; |
| clock-frequency = <600000000>; |
| st,syscfg = <&syscfg_core 0x224>; |
| }; |
| |
| /* fdma audio */ |
| fdma0: dma-controller@8e20000 { |
| compatible = "st,stih407-fdma-mpe31-11", "st,slim-rproc"; |
| reg = <0x8e20000 0x8000>, |
| <0x8e30000 0x3000>, |
| <0x8e37000 0x1000>, |
| <0x8e38000 0x8000>; |
| reg-names = "slimcore", "dmem", "peripherals", "imem"; |
| clocks = <&clk_s_c0_flexgen CLK_FDMA>, |
| <&clk_s_c0_flexgen CLK_EXT2F_A9>, |
| <&clk_s_c0_flexgen CLK_EXT2F_A9>, |
| <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>; |
| dma-channels = <16>; |
| #dma-cells = <3>; |
| }; |
| |
| /* fdma app */ |
| fdma1: dma-controller@8e40000 { |
| compatible = "st,stih407-fdma-mpe31-12", "st,slim-rproc"; |
| reg = <0x8e40000 0x8000>, |
| <0x8e50000 0x3000>, |
| <0x8e57000 0x1000>, |
| <0x8e58000 0x8000>; |
| reg-names = "slimcore", "dmem", "peripherals", "imem"; |
| clocks = <&clk_s_c0_flexgen CLK_FDMA>, |
| <&clk_s_c0_flexgen CLK_TX_ICN_DMU>, |
| <&clk_s_c0_flexgen CLK_TX_ICN_DMU>, |
| <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| |
| interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; |
| dma-channels = <16>; |
| #dma-cells = <3>; |
| }; |
| |
| /* fdma free running */ |
| fdma2: dma-controller@8e60000 { |
| compatible = "st,stih407-fdma-mpe31-13", "st,slim-rproc"; |
| reg = <0x8e60000 0x8000>, |
| <0x8e70000 0x3000>, |
| <0x8e77000 0x1000>, |
| <0x8e78000 0x8000>; |
| reg-names = "slimcore", "dmem", "peripherals", "imem"; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_NONE>; |
| dma-channels = <16>; |
| #dma-cells = <3>; |
| clocks = <&clk_s_c0_flexgen CLK_FDMA>, |
| <&clk_s_c0_flexgen CLK_EXT2F_A9>, |
| <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>, |
| <&clk_s_c0_flexgen CLK_EXT2F_A9>; |
| }; |
| |
| sti_sasg_codec: sti-sasg-codec { |
| compatible = "st,stih407-sas-codec"; |
| #sound-dai-cells = <1>; |
| status = "disabled"; |
| st,syscfg = <&syscfg_core>; |
| }; |
| |
| sti_uni_player0: sti-uni-player@8d80000 { |
| compatible = "st,sti-uni-player"; |
| #sound-dai-cells = <0>; |
| st,syscfg = <&syscfg_core>; |
| clocks = <&clk_s_d0_flexgen CLK_PCM_0>; |
| assigned-clocks = <&clk_s_d0_quadfs 0>, <&clk_s_d0_flexgen CLK_PCM_0>; |
| assigned-clock-parents = <0>, <&clk_s_d0_quadfs 0>; |
| assigned-clock-rates = <50000000>; |
| reg = <0x8d80000 0x158>; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_NONE>; |
| dmas = <&fdma0 2 0 1>; |
| dai-name = "Uni Player #0 (HDMI)"; |
| dma-names = "tx"; |
| st,uniperiph-id = <0>; |
| st,version = <5>; |
| st,mode = "HDMI"; |
| |
| status = "disabled"; |
| }; |
| |
| sti_uni_player1: sti-uni-player@8d81000 { |
| compatible = "st,sti-uni-player"; |
| #sound-dai-cells = <0>; |
| st,syscfg = <&syscfg_core>; |
| clocks = <&clk_s_d0_flexgen CLK_PCM_1>; |
| assigned-clocks = <&clk_s_d0_quadfs 1>, <&clk_s_d0_flexgen CLK_PCM_1>; |
| assigned-clock-parents = <0>, <&clk_s_d0_quadfs 1>; |
| assigned-clock-rates = <50000000>; |
| reg = <0x8d81000 0x158>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>; |
| dmas = <&fdma0 3 0 1>; |
| dai-name = "Uni Player #1 (PIO)"; |
| dma-names = "tx"; |
| st,uniperiph-id = <1>; |
| st,version = <5>; |
| st,mode = "PCM"; |
| |
| status = "disabled"; |
| }; |
| |
| sti_uni_player2: sti-uni-player@8d82000 { |
| compatible = "st,sti-uni-player"; |
| #sound-dai-cells = <0>; |
| st,syscfg = <&syscfg_core>; |
| clocks = <&clk_s_d0_flexgen CLK_PCM_2>; |
| assigned-clocks = <&clk_s_d0_quadfs 2>, <&clk_s_d0_flexgen CLK_PCM_2>; |
| assigned-clock-parents = <0>, <&clk_s_d0_quadfs 2>; |
| assigned-clock-rates = <50000000>; |
| reg = <0x8d82000 0x158>; |
| interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>; |
| dmas = <&fdma0 4 0 1>; |
| dai-name = "Uni Player #1 (DAC)"; |
| dma-names = "tx"; |
| st,uniperiph-id = <2>; |
| st,version = <5>; |
| st,mode = "PCM"; |
| |
| status = "disabled"; |
| }; |
| |
| sti_uni_player3: sti-uni-player@8d85000 { |
| compatible = "st,sti-uni-player"; |
| #sound-dai-cells = <0>; |
| st,syscfg = <&syscfg_core>; |
| clocks = <&clk_s_d0_flexgen CLK_SPDIFF>; |
| assigned-clocks = <&clk_s_d0_quadfs 3>, <&clk_s_d0_flexgen CLK_SPDIFF>; |
| assigned-clock-parents = <0>, <&clk_s_d0_quadfs 3>; |
| assigned-clock-rates = <50000000>; |
| reg = <0x8d85000 0x158>; |
| interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>; |
| dmas = <&fdma0 7 0 1>; |
| dma-names = "tx"; |
| dai-name = "Uni Player #1 (PIO)"; |
| st,uniperiph-id = <3>; |
| st,version = <5>; |
| st,mode = "SPDIF"; |
| |
| status = "disabled"; |
| }; |
| |
| sti_uni_reader0: sti-uni-reader@8d83000 { |
| compatible = "st,sti-uni-reader"; |
| #sound-dai-cells = <0>; |
| st,syscfg = <&syscfg_core>; |
| reg = <0x8d83000 0x158>; |
| interrupts = <GIC_SPI 87 IRQ_TYPE_NONE>; |
| dmas = <&fdma0 5 0 1>; |
| dma-names = "rx"; |
| dai-name = "Uni Reader #0 (PCM IN)"; |
| st,version = <3>; |
| |
| status = "disabled"; |
| }; |
| |
| sti_uni_reader1: sti-uni-reader@8d84000 { |
| compatible = "st,sti-uni-reader"; |
| #sound-dai-cells = <0>; |
| st,syscfg = <&syscfg_core>; |
| reg = <0x8d84000 0x158>; |
| interrupts = <GIC_SPI 88 IRQ_TYPE_NONE>; |
| dmas = <&fdma0 6 0 1>; |
| dma-names = "rx"; |
| dai-name = "Uni Reader #1 (HDMI RX)"; |
| st,version = <3>; |
| |
| status = "disabled"; |
| }; |
| }; |
| }; |
