| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (c) 2018 MediaTek Inc. |
| */ |
| #include <linux/bitfield.h> |
| #include <linux/io.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| #include <linux/of_net.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/regmap.h> |
| #include <linux/stmmac.h> |
| |
| #include "stmmac.h" |
| #include "stmmac_platform.h" |
| |
| /* Peri Configuration register for mt2712 */ |
| #define PERI_ETH_PHY_INTF_SEL 0x418 |
| #define PHY_INTF_MII 0 |
| #define PHY_INTF_RGMII 1 |
| #define PHY_INTF_RMII 4 |
| #define RMII_CLK_SRC_RXC BIT(4) |
| #define RMII_CLK_SRC_INTERNAL BIT(5) |
| |
| #define PERI_ETH_DLY 0x428 |
| #define ETH_DLY_GTXC_INV BIT(6) |
| #define ETH_DLY_GTXC_ENABLE BIT(5) |
| #define ETH_DLY_GTXC_STAGES GENMASK(4, 0) |
| #define ETH_DLY_TXC_INV BIT(20) |
| #define ETH_DLY_TXC_ENABLE BIT(19) |
| #define ETH_DLY_TXC_STAGES GENMASK(18, 14) |
| #define ETH_DLY_RXC_INV BIT(13) |
| #define ETH_DLY_RXC_ENABLE BIT(12) |
| #define ETH_DLY_RXC_STAGES GENMASK(11, 7) |
| |
| #define PERI_ETH_DLY_FINE 0x800 |
| #define ETH_RMII_DLY_TX_INV BIT(2) |
| #define ETH_FINE_DLY_GTXC BIT(1) |
| #define ETH_FINE_DLY_RXC BIT(0) |
| |
| struct mac_delay_struct { |
| u32 tx_delay; |
| u32 rx_delay; |
| bool tx_inv; |
| bool rx_inv; |
| }; |
| |
| struct mediatek_dwmac_plat_data { |
| const struct mediatek_dwmac_variant *variant; |
| struct mac_delay_struct mac_delay; |
| struct clk_bulk_data *clks; |
| struct device_node *np; |
| struct regmap *peri_regmap; |
| struct device *dev; |
| phy_interface_t phy_mode; |
| int num_clks_to_config; |
| bool rmii_clk_from_mac; |
| bool rmii_rxc; |
| }; |
| |
| struct mediatek_dwmac_variant { |
| int (*dwmac_set_phy_interface)(struct mediatek_dwmac_plat_data *plat); |
| int (*dwmac_set_delay)(struct mediatek_dwmac_plat_data *plat); |
| |
| /* clock ids to be requested */ |
| const char * const *clk_list; |
| int num_clks; |
| |
| u32 dma_bit_mask; |
| u32 rx_delay_max; |
| u32 tx_delay_max; |
| }; |
| |
| /* list of clocks required for mac */ |
| static const char * const mt2712_dwmac_clk_l[] = { |
| "axi", "apb", "mac_main", "ptp_ref", "rmii_internal" |
| }; |
| |
| static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat) |
| { |
| int rmii_clk_from_mac = plat->rmii_clk_from_mac ? RMII_CLK_SRC_INTERNAL : 0; |
| int rmii_rxc = plat->rmii_rxc ? RMII_CLK_SRC_RXC : 0; |
| u32 intf_val = 0; |
| |
| /* The clock labeled as "rmii_internal" in mt2712_dwmac_clk_l is needed |
| * only in RMII(when MAC provides the reference clock), and useless for |
| * RGMII/MII/RMII(when PHY provides the reference clock). |
| * num_clks_to_config indicates the real number of clocks should be |
| * configured, equals to (plat->variant->num_clks - 1) in default for all the case, |
| * then +1 for rmii_clk_from_mac case. |
| */ |
| plat->num_clks_to_config = plat->variant->num_clks - 1; |
| |
| /* select phy interface in top control domain */ |
| switch (plat->phy_mode) { |
| case PHY_INTERFACE_MODE_MII: |
| intf_val |= PHY_INTF_MII; |
| break; |
| case PHY_INTERFACE_MODE_RMII: |
| if (plat->rmii_clk_from_mac) |
| plat->num_clks_to_config++; |
| intf_val |= (PHY_INTF_RMII | rmii_rxc | rmii_clk_from_mac); |
| break; |
| case PHY_INTERFACE_MODE_RGMII: |
| case PHY_INTERFACE_MODE_RGMII_TXID: |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| intf_val |= PHY_INTF_RGMII; |
| break; |
| default: |
| dev_err(plat->dev, "phy interface not supported\n"); |
| return -EINVAL; |
| } |
| |
| regmap_write(plat->peri_regmap, PERI_ETH_PHY_INTF_SEL, intf_val); |
| |
| return 0; |
| } |
| |
| static void mt2712_delay_ps2stage(struct mediatek_dwmac_plat_data *plat) |
| { |
| struct mac_delay_struct *mac_delay = &plat->mac_delay; |
| |
| switch (plat->phy_mode) { |
| case PHY_INTERFACE_MODE_MII: |
| case PHY_INTERFACE_MODE_RMII: |
| /* 550ps per stage for MII/RMII */ |
| mac_delay->tx_delay /= 550; |
| mac_delay->rx_delay /= 550; |
| break; |
| case PHY_INTERFACE_MODE_RGMII: |
| case PHY_INTERFACE_MODE_RGMII_TXID: |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| /* 170ps per stage for RGMII */ |
| mac_delay->tx_delay /= 170; |
| mac_delay->rx_delay /= 170; |
| break; |
| default: |
| dev_err(plat->dev, "phy interface not supported\n"); |
| break; |
| } |
| } |
| |
| static void mt2712_delay_stage2ps(struct mediatek_dwmac_plat_data *plat) |
| { |
| struct mac_delay_struct *mac_delay = &plat->mac_delay; |
| |
| switch (plat->phy_mode) { |
| case PHY_INTERFACE_MODE_MII: |
| case PHY_INTERFACE_MODE_RMII: |
| /* 550ps per stage for MII/RMII */ |
| mac_delay->tx_delay *= 550; |
| mac_delay->rx_delay *= 550; |
| break; |
| case PHY_INTERFACE_MODE_RGMII: |
| case PHY_INTERFACE_MODE_RGMII_TXID: |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| /* 170ps per stage for RGMII */ |
| mac_delay->tx_delay *= 170; |
| mac_delay->rx_delay *= 170; |
| break; |
| default: |
| dev_err(plat->dev, "phy interface not supported\n"); |
| break; |
| } |
| } |
| |
| static int mt2712_set_delay(struct mediatek_dwmac_plat_data *plat) |
| { |
| struct mac_delay_struct *mac_delay = &plat->mac_delay; |
| u32 delay_val = 0, fine_val = 0; |
| |
| mt2712_delay_ps2stage(plat); |
| |
| switch (plat->phy_mode) { |
| case PHY_INTERFACE_MODE_MII: |
| delay_val |= FIELD_PREP(ETH_DLY_TXC_ENABLE, !!mac_delay->tx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_TXC_STAGES, mac_delay->tx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_TXC_INV, mac_delay->tx_inv); |
| |
| delay_val |= FIELD_PREP(ETH_DLY_RXC_ENABLE, !!mac_delay->rx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_RXC_STAGES, mac_delay->rx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv); |
| break; |
| case PHY_INTERFACE_MODE_RMII: |
| if (plat->rmii_clk_from_mac) { |
| /* case 1: mac provides the rmii reference clock, |
| * and the clock output to TXC pin. |
| * The egress timing can be adjusted by GTXC delay macro circuit. |
| * The ingress timing can be adjusted by TXC delay macro circuit. |
| */ |
| delay_val |= FIELD_PREP(ETH_DLY_TXC_ENABLE, !!mac_delay->rx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_TXC_STAGES, mac_delay->rx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_TXC_INV, mac_delay->rx_inv); |
| |
| delay_val |= FIELD_PREP(ETH_DLY_GTXC_ENABLE, !!mac_delay->tx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_GTXC_STAGES, mac_delay->tx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_GTXC_INV, mac_delay->tx_inv); |
| } else { |
| /* case 2: the rmii reference clock is from external phy, |
| * and the property "rmii_rxc" indicates which pin(TXC/RXC) |
| * the reference clk is connected to. The reference clock is a |
| * received signal, so rx_delay/rx_inv are used to indicate |
| * the reference clock timing adjustment |
| */ |
| if (plat->rmii_rxc) { |
| /* the rmii reference clock from outside is connected |
| * to RXC pin, the reference clock will be adjusted |
| * by RXC delay macro circuit. |
| */ |
| delay_val |= FIELD_PREP(ETH_DLY_RXC_ENABLE, !!mac_delay->rx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_RXC_STAGES, mac_delay->rx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv); |
| } else { |
| /* the rmii reference clock from outside is connected |
| * to TXC pin, the reference clock will be adjusted |
| * by TXC delay macro circuit. |
| */ |
| delay_val |= FIELD_PREP(ETH_DLY_TXC_ENABLE, !!mac_delay->rx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_TXC_STAGES, mac_delay->rx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_TXC_INV, mac_delay->rx_inv); |
| } |
| /* tx_inv will inverse the tx clock inside mac relateive to |
| * reference clock from external phy, |
| * and this bit is located in the same register with fine-tune |
| */ |
| if (mac_delay->tx_inv) |
| fine_val = ETH_RMII_DLY_TX_INV; |
| } |
| break; |
| case PHY_INTERFACE_MODE_RGMII: |
| case PHY_INTERFACE_MODE_RGMII_TXID: |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| fine_val = ETH_FINE_DLY_GTXC | ETH_FINE_DLY_RXC; |
| |
| delay_val |= FIELD_PREP(ETH_DLY_GTXC_ENABLE, !!mac_delay->tx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_GTXC_STAGES, mac_delay->tx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_GTXC_INV, mac_delay->tx_inv); |
| |
| delay_val |= FIELD_PREP(ETH_DLY_RXC_ENABLE, !!mac_delay->rx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_RXC_STAGES, mac_delay->rx_delay); |
| delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv); |
| break; |
| default: |
| dev_err(plat->dev, "phy interface not supported\n"); |
| return -EINVAL; |
| } |
| regmap_write(plat->peri_regmap, PERI_ETH_DLY, delay_val); |
| regmap_write(plat->peri_regmap, PERI_ETH_DLY_FINE, fine_val); |
| |
| mt2712_delay_stage2ps(plat); |
| |
| return 0; |
| } |
| |
| static const struct mediatek_dwmac_variant mt2712_gmac_variant = { |
| .dwmac_set_phy_interface = mt2712_set_interface, |
| .dwmac_set_delay = mt2712_set_delay, |
| .clk_list = mt2712_dwmac_clk_l, |
| .num_clks = ARRAY_SIZE(mt2712_dwmac_clk_l), |
| .dma_bit_mask = 33, |
| .rx_delay_max = 17600, |
| .tx_delay_max = 17600, |
| }; |
| |
| static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat) |
| { |
| struct mac_delay_struct *mac_delay = &plat->mac_delay; |
| u32 tx_delay_ps, rx_delay_ps; |
| int err; |
| |
| plat->peri_regmap = syscon_regmap_lookup_by_phandle(plat->np, "mediatek,pericfg"); |
| if (IS_ERR(plat->peri_regmap)) { |
| dev_err(plat->dev, "Failed to get pericfg syscon\n"); |
| return PTR_ERR(plat->peri_regmap); |
| } |
| |
| err = of_get_phy_mode(plat->np, &plat->phy_mode); |
| if (err) { |
| dev_err(plat->dev, "not find phy-mode\n"); |
| return err; |
| } |
| |
| if (!of_property_read_u32(plat->np, "mediatek,tx-delay-ps", &tx_delay_ps)) { |
| if (tx_delay_ps < plat->variant->tx_delay_max) { |
| mac_delay->tx_delay = tx_delay_ps; |
| } else { |
| dev_err(plat->dev, "Invalid TX clock delay: %dps\n", tx_delay_ps); |
| return -EINVAL; |
| } |
| } |
| |
| if (!of_property_read_u32(plat->np, "mediatek,rx-delay-ps", &rx_delay_ps)) { |
| if (rx_delay_ps < plat->variant->rx_delay_max) { |
| mac_delay->rx_delay = rx_delay_ps; |
| } else { |
| dev_err(plat->dev, "Invalid RX clock delay: %dps\n", rx_delay_ps); |
| return -EINVAL; |
| } |
| } |
| |
| mac_delay->tx_inv = of_property_read_bool(plat->np, "mediatek,txc-inverse"); |
| mac_delay->rx_inv = of_property_read_bool(plat->np, "mediatek,rxc-inverse"); |
| plat->rmii_rxc = of_property_read_bool(plat->np, "mediatek,rmii-rxc"); |
| plat->rmii_clk_from_mac = of_property_read_bool(plat->np, "mediatek,rmii-clk-from-mac"); |
| |
| return 0; |
| } |
| |
| static int mediatek_dwmac_clk_init(struct mediatek_dwmac_plat_data *plat) |
| { |
| const struct mediatek_dwmac_variant *variant = plat->variant; |
| int i, num = variant->num_clks; |
| |
| plat->clks = devm_kcalloc(plat->dev, num, sizeof(*plat->clks), GFP_KERNEL); |
| if (!plat->clks) |
| return -ENOMEM; |
| |
| for (i = 0; i < num; i++) |
| plat->clks[i].id = variant->clk_list[i]; |
| |
| plat->num_clks_to_config = variant->num_clks; |
| |
| return devm_clk_bulk_get(plat->dev, num, plat->clks); |
| } |
| |
| static int mediatek_dwmac_init(struct platform_device *pdev, void *priv) |
| { |
| struct mediatek_dwmac_plat_data *plat = priv; |
| const struct mediatek_dwmac_variant *variant = plat->variant; |
| int ret; |
| |
| ret = dma_set_mask_and_coherent(plat->dev, DMA_BIT_MASK(variant->dma_bit_mask)); |
| if (ret) { |
| dev_err(plat->dev, "No suitable DMA available, err = %d\n", ret); |
| return ret; |
| } |
| |
| ret = variant->dwmac_set_phy_interface(plat); |
| if (ret) { |
| dev_err(plat->dev, "failed to set phy interface, err = %d\n", ret); |
| return ret; |
| } |
| |
| ret = variant->dwmac_set_delay(plat); |
| if (ret) { |
| dev_err(plat->dev, "failed to set delay value, err = %d\n", ret); |
| return ret; |
| } |
| |
| ret = clk_bulk_prepare_enable(plat->num_clks_to_config, plat->clks); |
| if (ret) { |
| dev_err(plat->dev, "failed to enable clks, err = %d\n", ret); |
| return ret; |
| } |
| |
| pm_runtime_enable(&pdev->dev); |
| pm_runtime_get_sync(&pdev->dev); |
| |
| return 0; |
| } |
| |
| static void mediatek_dwmac_exit(struct platform_device *pdev, void *priv) |
| { |
| struct mediatek_dwmac_plat_data *plat = priv; |
| |
| clk_bulk_disable_unprepare(plat->num_clks_to_config, plat->clks); |
| |
| pm_runtime_put_sync(&pdev->dev); |
| pm_runtime_disable(&pdev->dev); |
| } |
| |
| static int mediatek_dwmac_probe(struct platform_device *pdev) |
| { |
| struct mediatek_dwmac_plat_data *priv_plat; |
| struct plat_stmmacenet_data *plat_dat; |
| struct stmmac_resources stmmac_res; |
| int ret; |
| |
| priv_plat = devm_kzalloc(&pdev->dev, sizeof(*priv_plat), GFP_KERNEL); |
| if (!priv_plat) |
| return -ENOMEM; |
| |
| priv_plat->variant = of_device_get_match_data(&pdev->dev); |
| if (!priv_plat->variant) { |
| dev_err(&pdev->dev, "Missing dwmac-mediatek variant\n"); |
| return -EINVAL; |
| } |
| |
| priv_plat->dev = &pdev->dev; |
| priv_plat->np = pdev->dev.of_node; |
| |
| ret = mediatek_dwmac_config_dt(priv_plat); |
| if (ret) |
| return ret; |
| |
| ret = mediatek_dwmac_clk_init(priv_plat); |
| if (ret) |
| return ret; |
| |
| ret = stmmac_get_platform_resources(pdev, &stmmac_res); |
| if (ret) |
| return ret; |
| |
| plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); |
| if (IS_ERR(plat_dat)) |
| return PTR_ERR(plat_dat); |
| |
| plat_dat->interface = priv_plat->phy_mode; |
| plat_dat->has_gmac4 = 1; |
| plat_dat->has_gmac = 0; |
| plat_dat->pmt = 0; |
| plat_dat->riwt_off = 1; |
| plat_dat->maxmtu = ETH_DATA_LEN; |
| plat_dat->bsp_priv = priv_plat; |
| plat_dat->init = mediatek_dwmac_init; |
| plat_dat->exit = mediatek_dwmac_exit; |
| mediatek_dwmac_init(pdev, priv_plat); |
| |
| ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); |
| if (ret) { |
| stmmac_remove_config_dt(pdev, plat_dat); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static const struct of_device_id mediatek_dwmac_match[] = { |
| { .compatible = "mediatek,mt2712-gmac", |
| .data = &mt2712_gmac_variant }, |
| { } |
| }; |
| |
| MODULE_DEVICE_TABLE(of, mediatek_dwmac_match); |
| |
| static struct platform_driver mediatek_dwmac_driver = { |
| .probe = mediatek_dwmac_probe, |
| .remove = stmmac_pltfr_remove, |
| .driver = { |
| .name = "dwmac-mediatek", |
| .pm = &stmmac_pltfr_pm_ops, |
| .of_match_table = mediatek_dwmac_match, |
| }, |
| }; |
| module_platform_driver(mediatek_dwmac_driver); |
| |
| MODULE_AUTHOR("Biao Huang <biao.huang@mediatek.com>"); |
| MODULE_DESCRIPTION("MediaTek DWMAC specific glue layer"); |
| MODULE_LICENSE("GPL v2"); |