| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| // Copyright (c) 2019 Jernej Skrabec <jernej.skrabec@siol.net> |
| |
| /dts-v1/; |
| |
| #include "sun50i-h6.dtsi" |
| #include "sun50i-h6-cpu-opp.dtsi" |
| |
| #include <dt-bindings/gpio/gpio.h> |
| |
| / { |
| model = "Tanix TX6"; |
| compatible = "oranth,tanix-tx6", "allwinner,sun50i-h6"; |
| |
| aliases { |
| serial0 = &uart0; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| connector { |
| compatible = "hdmi-connector"; |
| ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ |
| type = "a"; |
| |
| port { |
| hdmi_con_in: endpoint { |
| remote-endpoint = <&hdmi_out_con>; |
| }; |
| }; |
| }; |
| |
| reg_vcc3v3: regulator-vcc3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| reg_vdd_cpu_gpu: regulator-vdd-cpu-gpu { |
| compatible = "regulator-fixed"; |
| regulator-name = "vdd-cpu-gpu"; |
| regulator-min-microvolt = <1135000>; |
| regulator-max-microvolt = <1135000>; |
| }; |
| }; |
| |
| &cpu0 { |
| cpu-supply = <®_vdd_cpu_gpu>; |
| }; |
| |
| &de { |
| status = "okay"; |
| }; |
| |
| &dwc3 { |
| status = "okay"; |
| }; |
| |
| &ehci0 { |
| status = "okay"; |
| }; |
| |
| &ehci3 { |
| status = "okay"; |
| }; |
| |
| &gpu { |
| mali-supply = <®_vdd_cpu_gpu>; |
| status = "okay"; |
| }; |
| |
| &hdmi { |
| status = "okay"; |
| }; |
| |
| &hdmi_out { |
| hdmi_out_con: endpoint { |
| remote-endpoint = <&hdmi_con_in>; |
| }; |
| }; |
| |
| &mmc0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc0_pins>; |
| vmmc-supply = <®_vcc3v3>; |
| cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; |
| bus-width = <4>; |
| status = "okay"; |
| }; |
| |
| &ohci0 { |
| status = "okay"; |
| }; |
| |
| &ohci3 { |
| status = "okay"; |
| }; |
| |
| &r_ir { |
| linux,rc-map-name = "rc-tanix-tx5max"; |
| status = "okay"; |
| }; |
| |
| &uart0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_ph_pins>; |
| status = "okay"; |
| }; |
| |
| &usb2otg { |
| dr_mode = "host"; |
| status = "okay"; |
| }; |
| |
| &usb2phy { |
| status = "okay"; |
| }; |
| |
| &usb3phy { |
| status = "okay"; |
| }; |