| # SPDX-License-Identifier: GPL-2.0-only |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/soc/qcom/qcom,rpmh-rsc.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: Qualcomm RPMH RSC |
| |
| maintainers: |
| - Bjorn Andersson <bjorn.andersson@linaro.org> |
| |
| description: | |
| Resource Power Manager Hardened (RPMH) is the mechanism for communicating |
| with the hardened resource accelerators on Qualcomm SoCs. Requests to the |
| resources can be written to the Trigger Command Set (TCS) registers and |
| using a (addr, val) pair and triggered. Messages in the TCS are then sent in |
| sequence over an internal bus. |
| |
| The hardware block (Direct Resource Voter or DRV) is a part of the h/w entity |
| (Resource State Coordinator a.k.a RSC) that can handle multiple sleep and |
| active/wake resource requests. Multiple such DRVs can exist in a SoC and can |
| be written to from Linux. The structure of each DRV follows the same template |
| with a few variations that are captured by the properties here. |
| |
| A TCS may be triggered from Linux or triggered by the F/W after all the CPUs |
| have powered off to facilitate idle power saving. TCS could be classified as:: |
| ACTIVE - Triggered by Linux |
| SLEEP - Triggered by F/W |
| WAKE - Triggered by F/W |
| CONTROL - Triggered by F/W |
| See also:: <dt-bindings/soc/qcom,rpmh-rsc.h> |
| |
| The order in which they are described in the DT, should match the hardware |
| configuration. |
| |
| Requests can be made for the state of a resource, when the subsystem is |
| active or idle. When all subsystems like Modem, GPU, CPU are idle, the |
| resource state will be an aggregate of the sleep votes from each of those |
| subsystems. Clients may request a sleep value for their shared resources in |
| addition to the active mode requests. |
| |
| Drivers that want to use the RSC to communicate with RPMH must specify their |
| bindings as child nodes of the RSC controllers they wish to communicate with. |
| |
| properties: |
| compatible: |
| const: qcom,rpmh-rsc |
| |
| interrupts: |
| minItems: 1 |
| maxItems: 4 |
| description: |
| The interrupt that trips when a message complete/response is received for |
| this DRV from the accelerators. |
| Number of interrupts must match number of DRV blocks. |
| |
| label: |
| description: |
| Name for the RSC. The name would be used in trace logs. |
| |
| qcom,drv-id: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: |
| The ID of the DRV in the RSC block that will be used by this controller. |
| |
| qcom,tcs-config: |
| $ref: /schemas/types.yaml#/definitions/uint32-matrix |
| minItems: 4 |
| maxItems: 4 |
| items: |
| items: |
| - description: | |
| TCS type:: |
| - ACTIVE_TCS |
| - SLEEP_TCS |
| - WAKE_TCS |
| - CONTROL_TCS |
| enum: [ 0, 1, 2, 3 ] |
| - description: Number of TCS |
| description: | |
| The tuple defining the configuration of TCS. Must have two cells which |
| describe each TCS type. The order of the TCS must match the hardware |
| configuration. |
| |
| qcom,tcs-offset: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: |
| The offset of the TCS blocks. |
| |
| reg: |
| minItems: 1 |
| maxItems: 4 |
| |
| reg-names: |
| minItems: 1 |
| items: |
| - const: drv-0 |
| - const: drv-1 |
| - const: drv-2 |
| - const: drv-3 |
| |
| bcm-voter: |
| $ref: /schemas/interconnect/qcom,bcm-voter.yaml# |
| |
| clock-controller: |
| $ref: /schemas/clock/qcom,rpmhcc.yaml# |
| |
| power-controller: |
| $ref: /schemas/power/qcom,rpmpd.yaml# |
| |
| patternProperties: |
| '-regulators$': |
| $ref: /schemas/regulator/qcom,rpmh-regulator.yaml# |
| |
| required: |
| - compatible |
| - interrupts |
| - qcom,drv-id |
| - qcom,tcs-config |
| - qcom,tcs-offset |
| - reg |
| - reg-names |
| |
| additionalProperties: false |
| |
| examples: |
| - | |
| // For a TCS whose RSC base address is 0x179C0000 and is at a DRV id of |
| // 2, the register offsets for DRV2 start at 0D00, the register |
| // calculations are like this:: |
| // DRV0: 0x179C0000 |
| // DRV2: 0x179C0000 + 0x10000 = 0x179D0000 |
| // DRV2: 0x179C0000 + 0x10000 * 2 = 0x179E0000 |
| // TCS-OFFSET: 0xD00 |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/soc/qcom,rpmh-rsc.h> |
| |
| rsc@179c0000 { |
| compatible = "qcom,rpmh-rsc"; |
| reg = <0x179c0000 0x10000>, |
| <0x179d0000 0x10000>, |
| <0x179e0000 0x10000>; |
| reg-names = "drv-0", "drv-1", "drv-2"; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| label = "apps_rsc"; |
| qcom,tcs-offset = <0xd00>; |
| qcom,drv-id = <2>; |
| qcom,tcs-config = <ACTIVE_TCS 2>, |
| <SLEEP_TCS 3>, |
| <WAKE_TCS 3>, |
| <CONTROL_TCS 1>; |
| }; |
| |
| - | |
| // For a TCS whose RSC base address is 0xAF20000 and is at DRV id of 0, the |
| // register offsets for DRV0 start at 01C00, the register calculations are |
| // like this:: |
| // DRV0: 0xAF20000 |
| // TCS-OFFSET: 0x1C00 |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/soc/qcom,rpmh-rsc.h> |
| |
| rsc@af20000 { |
| compatible = "qcom,rpmh-rsc"; |
| reg = <0xaf20000 0x10000>; |
| reg-names = "drv-0"; |
| interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>; |
| label = "disp_rsc"; |
| qcom,tcs-offset = <0x1c00>; |
| qcom,drv-id = <0>; |
| qcom,tcs-config = <ACTIVE_TCS 0>, |
| <SLEEP_TCS 1>, |
| <WAKE_TCS 1>, |
| <CONTROL_TCS 0>; |
| }; |
| |
| - | |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/soc/qcom,rpmh-rsc.h> |
| #include <dt-bindings/power/qcom-rpmpd.h> |
| |
| rsc@18200000 { |
| compatible = "qcom,rpmh-rsc"; |
| reg = <0x18200000 0x10000>, |
| <0x18210000 0x10000>, |
| <0x18220000 0x10000>; |
| reg-names = "drv-0", "drv-1", "drv-2"; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| label = "apps_rsc"; |
| qcom,tcs-offset = <0xd00>; |
| qcom,drv-id = <2>; |
| qcom,tcs-config = <ACTIVE_TCS 2>, |
| <SLEEP_TCS 3>, |
| <WAKE_TCS 3>, |
| <CONTROL_TCS 0>; |
| |
| clock-controller { |
| compatible = "qcom,sm8350-rpmh-clk"; |
| #clock-cells = <1>; |
| clock-names = "xo"; |
| clocks = <&xo_board>; |
| }; |
| |
| power-controller { |
| compatible = "qcom,sm8350-rpmhpd"; |
| #power-domain-cells = <1>; |
| operating-points-v2 = <&rpmhpd_opp_table>; |
| |
| rpmhpd_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| rpmhpd_opp_ret: opp1 { |
| opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; |
| }; |
| |
| rpmhpd_opp_min_svs: opp2 { |
| opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; |
| }; |
| |
| rpmhpd_opp_low_svs: opp3 { |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; |
| }; |
| |
| rpmhpd_opp_svs: opp4 { |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS>; |
| }; |
| |
| rpmhpd_opp_svs_l1: opp5 { |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; |
| }; |
| |
| rpmhpd_opp_nom: opp6 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM>; |
| }; |
| |
| rpmhpd_opp_nom_l1: opp7 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; |
| }; |
| |
| rpmhpd_opp_nom_l2: opp8 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>; |
| }; |
| |
| rpmhpd_opp_turbo: opp9 { |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; |
| }; |
| |
| rpmhpd_opp_turbo_l1: opp10 { |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; |
| }; |
| }; |
| }; |
| |
| bcm-voter { |
| compatible = "qcom,bcm-voter"; |
| }; |
| }; |
