| /* |
| * MPC83xx SPI controller driver. |
| * |
| * Maintainer: Kumar Gala |
| * |
| * Copyright (C) 2006 Polycom, Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| */ |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/types.h> |
| #include <linux/kernel.h> |
| #include <linux/completion.h> |
| #include <linux/interrupt.h> |
| #include <linux/delay.h> |
| #include <linux/irq.h> |
| #include <linux/device.h> |
| #include <linux/spi/spi.h> |
| #include <linux/spi/spi_bitbang.h> |
| #include <linux/platform_device.h> |
| #include <linux/fsl_devices.h> |
| |
| #include <asm/irq.h> |
| #include <asm/io.h> |
| |
| /* SPI Controller registers */ |
| struct mpc83xx_spi_reg { |
| u8 res1[0x20]; |
| __be32 mode; |
| __be32 event; |
| __be32 mask; |
| __be32 command; |
| __be32 transmit; |
| __be32 receive; |
| }; |
| |
| /* SPI Controller mode register definitions */ |
| #define SPMODE_LOOP (1 << 30) |
| #define SPMODE_CI_INACTIVEHIGH (1 << 29) |
| #define SPMODE_CP_BEGIN_EDGECLK (1 << 28) |
| #define SPMODE_DIV16 (1 << 27) |
| #define SPMODE_REV (1 << 26) |
| #define SPMODE_MS (1 << 25) |
| #define SPMODE_ENABLE (1 << 24) |
| #define SPMODE_LEN(x) ((x) << 20) |
| #define SPMODE_PM(x) ((x) << 16) |
| #define SPMODE_OP (1 << 14) |
| #define SPMODE_CG(x) ((x) << 7) |
| |
| /* |
| * Default for SPI Mode: |
| * SPI MODE 0 (inactive low, phase middle, MSB, 8-bit length, slow clk |
| */ |
| #define SPMODE_INIT_VAL (SPMODE_CI_INACTIVEHIGH | SPMODE_DIV16 | SPMODE_REV | \ |
| SPMODE_MS | SPMODE_LEN(7) | SPMODE_PM(0xf)) |
| |
| /* SPIE register values */ |
| #define SPIE_NE 0x00000200 /* Not empty */ |
| #define SPIE_NF 0x00000100 /* Not full */ |
| |
| /* SPIM register values */ |
| #define SPIM_NE 0x00000200 /* Not empty */ |
| #define SPIM_NF 0x00000100 /* Not full */ |
| |
| /* SPI Controller driver's private data. */ |
| struct mpc83xx_spi { |
| struct mpc83xx_spi_reg __iomem *base; |
| |
| /* rx & tx bufs from the spi_transfer */ |
| const void *tx; |
| void *rx; |
| |
| /* functions to deal with different sized buffers */ |
| void (*get_rx) (u32 rx_data, struct mpc83xx_spi *); |
| u32(*get_tx) (struct mpc83xx_spi *); |
| |
| unsigned int count; |
| int irq; |
| |
| unsigned nsecs; /* (clock cycle time)/2 */ |
| |
| u32 spibrg; /* SPIBRG input clock */ |
| u32 rx_shift; /* RX data reg shift when in qe mode */ |
| u32 tx_shift; /* TX data reg shift when in qe mode */ |
| |
| bool qe_mode; |
| |
| u8 busy; |
| |
| struct workqueue_struct *workqueue; |
| struct work_struct work; |
| |
| struct list_head queue; |
| spinlock_t lock; |
| |
| struct completion done; |
| }; |
| |
| struct spi_mpc83xx_cs { |
| /* functions to deal with different sized buffers */ |
| void (*get_rx) (u32 rx_data, struct mpc83xx_spi *); |
| u32 (*get_tx) (struct mpc83xx_spi *); |
| u32 rx_shift; /* RX data reg shift when in qe mode */ |
| u32 tx_shift; /* TX data reg shift when in qe mode */ |
| u32 hw_mode; /* Holds HW mode register settings */ |
| }; |
| |
| static inline void mpc83xx_spi_write_reg(__be32 __iomem * reg, u32 val) |
| { |
| out_be32(reg, val); |
| } |
| |
| static inline u32 mpc83xx_spi_read_reg(__be32 __iomem * reg) |
| { |
| return in_be32(reg); |
| } |
| |
| #define MPC83XX_SPI_RX_BUF(type) \ |
| static \ |
| void mpc83xx_spi_rx_buf_##type(u32 data, struct mpc83xx_spi *mpc83xx_spi) \ |
| { \ |
| type * rx = mpc83xx_spi->rx; \ |
| *rx++ = (type)(data >> mpc83xx_spi->rx_shift); \ |
| mpc83xx_spi->rx = rx; \ |
| } |
| |
| #define MPC83XX_SPI_TX_BUF(type) \ |
| static \ |
| u32 mpc83xx_spi_tx_buf_##type(struct mpc83xx_spi *mpc83xx_spi) \ |
| { \ |
| u32 data; \ |
| const type * tx = mpc83xx_spi->tx; \ |
| if (!tx) \ |
| return 0; \ |
| data = *tx++ << mpc83xx_spi->tx_shift; \ |
| mpc83xx_spi->tx = tx; \ |
| return data; \ |
| } |
| |
| MPC83XX_SPI_RX_BUF(u8) |
| MPC83XX_SPI_RX_BUF(u16) |
| MPC83XX_SPI_RX_BUF(u32) |
| MPC83XX_SPI_TX_BUF(u8) |
| MPC83XX_SPI_TX_BUF(u16) |
| MPC83XX_SPI_TX_BUF(u32) |
| |
| static void mpc83xx_spi_chipselect(struct spi_device *spi, int value) |
| { |
| struct mpc83xx_spi *mpc83xx_spi = spi_master_get_devdata(spi->master); |
| struct fsl_spi_platform_data *pdata = spi->dev.parent->platform_data; |
| bool pol = spi->mode & SPI_CS_HIGH; |
| struct spi_mpc83xx_cs *cs = spi->controller_state; |
| |
| if (value == BITBANG_CS_INACTIVE) { |
| if (pdata->cs_control) |
| pdata->cs_control(spi, !pol); |
| } |
| |
| if (value == BITBANG_CS_ACTIVE) { |
| u32 regval = mpc83xx_spi_read_reg(&mpc83xx_spi->base->mode); |
| |
| mpc83xx_spi->rx_shift = cs->rx_shift; |
| mpc83xx_spi->tx_shift = cs->tx_shift; |
| mpc83xx_spi->get_rx = cs->get_rx; |
| mpc83xx_spi->get_tx = cs->get_tx; |
| |
| if (cs->hw_mode != regval) { |
| unsigned long flags; |
| __be32 __iomem *mode = &mpc83xx_spi->base->mode; |
| |
| regval = cs->hw_mode; |
| /* Turn off IRQs locally to minimize time that |
| * SPI is disabled |
| */ |
| local_irq_save(flags); |
| /* Turn off SPI unit prior changing mode */ |
| mpc83xx_spi_write_reg(mode, regval & ~SPMODE_ENABLE); |
| mpc83xx_spi_write_reg(mode, regval); |
| local_irq_restore(flags); |
| } |
| if (pdata->cs_control) |
| pdata->cs_control(spi, pol); |
| } |
| } |
| |
| static |
| int mpc83xx_spi_setup_transfer(struct spi_device *spi, struct spi_transfer *t) |
| { |
| struct mpc83xx_spi *mpc83xx_spi; |
| u32 regval; |
| u8 bits_per_word, pm; |
| u32 hz; |
| struct spi_mpc83xx_cs *cs = spi->controller_state; |
| |
| mpc83xx_spi = spi_master_get_devdata(spi->master); |
| |
| if (t) { |
| bits_per_word = t->bits_per_word; |
| hz = t->speed_hz; |
| } else { |
| bits_per_word = 0; |
| hz = 0; |
| } |
| |
| /* spi_transfer level calls that work per-word */ |
| if (!bits_per_word) |
| bits_per_word = spi->bits_per_word; |
| |
| /* Make sure its a bit width we support [4..16, 32] */ |
| if ((bits_per_word < 4) |
| || ((bits_per_word > 16) && (bits_per_word != 32))) |
| return -EINVAL; |
| |
| if (!hz) |
| hz = spi->max_speed_hz; |
| |
| cs->rx_shift = 0; |
| cs->tx_shift = 0; |
| if (bits_per_word <= 8) { |
| cs->get_rx = mpc83xx_spi_rx_buf_u8; |
| cs->get_tx = mpc83xx_spi_tx_buf_u8; |
| if (mpc83xx_spi->qe_mode) { |
| cs->rx_shift = 16; |
| cs->tx_shift = 24; |
| } |
| } else if (bits_per_word <= 16) { |
| cs->get_rx = mpc83xx_spi_rx_buf_u16; |
| cs->get_tx = mpc83xx_spi_tx_buf_u16; |
| if (mpc83xx_spi->qe_mode) { |
| cs->rx_shift = 16; |
| cs->tx_shift = 16; |
| } |
| } else if (bits_per_word <= 32) { |
| cs->get_rx = mpc83xx_spi_rx_buf_u32; |
| cs->get_tx = mpc83xx_spi_tx_buf_u32; |
| } else |
| return -EINVAL; |
| |
| if (mpc83xx_spi->qe_mode && spi->mode & SPI_LSB_FIRST) { |
| cs->tx_shift = 0; |
| if (bits_per_word <= 8) |
| cs->rx_shift = 8; |
| else |
| cs->rx_shift = 0; |
| } |
| |
| mpc83xx_spi->rx_shift = cs->rx_shift; |
| mpc83xx_spi->tx_shift = cs->tx_shift; |
| mpc83xx_spi->get_rx = cs->get_rx; |
| mpc83xx_spi->get_tx = cs->get_tx; |
| |
| if (bits_per_word == 32) |
| bits_per_word = 0; |
| else |
| bits_per_word = bits_per_word - 1; |
| |
| /* mask out bits we are going to set */ |
| cs->hw_mode &= ~(SPMODE_LEN(0xF) | SPMODE_DIV16 |
| | SPMODE_PM(0xF)); |
| |
| cs->hw_mode |= SPMODE_LEN(bits_per_word); |
| |
| if ((mpc83xx_spi->spibrg / hz) > 64) { |
| cs->hw_mode |= SPMODE_DIV16; |
| pm = mpc83xx_spi->spibrg / (hz * 64); |
| if (pm > 16) { |
| dev_err(&spi->dev, "Requested speed is too " |
| "low: %d Hz. Will use %d Hz instead.\n", |
| hz, mpc83xx_spi->spibrg / 1024); |
| pm = 16; |
| } |
| } else |
| pm = mpc83xx_spi->spibrg / (hz * 4); |
| if (pm) |
| pm--; |
| |
| cs->hw_mode |= SPMODE_PM(pm); |
| regval = mpc83xx_spi_read_reg(&mpc83xx_spi->base->mode); |
| if (cs->hw_mode != regval) { |
| unsigned long flags; |
| __be32 __iomem *mode = &mpc83xx_spi->base->mode; |
| |
| regval = cs->hw_mode; |
| /* Turn off IRQs locally to minimize time |
| * that SPI is disabled |
| */ |
| local_irq_save(flags); |
| /* Turn off SPI unit prior changing mode */ |
| mpc83xx_spi_write_reg(mode, regval & ~SPMODE_ENABLE); |
| mpc83xx_spi_write_reg(mode, regval); |
| local_irq_restore(flags); |
| } |
| return 0; |
| } |
| |
| static int mpc83xx_spi_bufs(struct spi_device *spi, struct spi_transfer *t) |
| { |
| struct mpc83xx_spi *mpc83xx_spi; |
| u32 word, len, bits_per_word; |
| |
| mpc83xx_spi = spi_master_get_devdata(spi->master); |
| |
| mpc83xx_spi->tx = t->tx_buf; |
| mpc83xx_spi->rx = t->rx_buf; |
| bits_per_word = spi->bits_per_word; |
| if (t->bits_per_word) |
| bits_per_word = t->bits_per_word; |
| len = t->len; |
| if (bits_per_word > 8) { |
| /* invalid length? */ |
| if (len & 1) |
| return -EINVAL; |
| len /= 2; |
| } |
| if (bits_per_word > 16) { |
| /* invalid length? */ |
| if (len & 1) |
| return -EINVAL; |
| len /= 2; |
| } |
| mpc83xx_spi->count = len; |
| |
| INIT_COMPLETION(mpc83xx_spi->done); |
| |
| /* enable rx ints */ |
| mpc83xx_spi_write_reg(&mpc83xx_spi->base->mask, SPIM_NE); |
| |
| /* transmit word */ |
| word = mpc83xx_spi->get_tx(mpc83xx_spi); |
| mpc83xx_spi_write_reg(&mpc83xx_spi->base->transmit, word); |
| |
| wait_for_completion(&mpc83xx_spi->done); |
| |
| /* disable rx ints */ |
| mpc83xx_spi_write_reg(&mpc83xx_spi->base->mask, 0); |
| |
| return mpc83xx_spi->count; |
| } |
| |
| static void mpc83xx_spi_work(struct work_struct *work) |
| { |
| struct mpc83xx_spi *mpc83xx_spi = |
| container_of(work, struct mpc83xx_spi, work); |
| |
| spin_lock_irq(&mpc83xx_spi->lock); |
| mpc83xx_spi->busy = 1; |
| while (!list_empty(&mpc83xx_spi->queue)) { |
| struct spi_message *m; |
| struct spi_device *spi; |
| struct spi_transfer *t = NULL; |
| unsigned cs_change; |
| int status, nsecs = 50; |
| |
| m = container_of(mpc83xx_spi->queue.next, |
| struct spi_message, queue); |
| list_del_init(&m->queue); |
| spin_unlock_irq(&mpc83xx_spi->lock); |
| |
| spi = m->spi; |
| cs_change = 1; |
| status = 0; |
| list_for_each_entry(t, &m->transfers, transfer_list) { |
| if (t->bits_per_word || t->speed_hz) { |
| /* Don't allow changes if CS is active */ |
| status = -EINVAL; |
| |
| if (cs_change) |
| status = mpc83xx_spi_setup_transfer(spi, t); |
| if (status < 0) |
| break; |
| } |
| |
| if (cs_change) |
| mpc83xx_spi_chipselect(spi, BITBANG_CS_ACTIVE); |
| cs_change = t->cs_change; |
| if (t->len) |
| status = mpc83xx_spi_bufs(spi, t); |
| if (status) { |
| status = -EMSGSIZE; |
| break; |
| } |
| m->actual_length += t->len; |
| |
| if (t->delay_usecs) |
| udelay(t->delay_usecs); |
| |
| if (cs_change) { |
| ndelay(nsecs); |
| mpc83xx_spi_chipselect(spi, BITBANG_CS_INACTIVE); |
| ndelay(nsecs); |
| } |
| } |
| |
| m->status = status; |
| m->complete(m->context); |
| |
| if (status || !cs_change) { |
| ndelay(nsecs); |
| mpc83xx_spi_chipselect(spi, BITBANG_CS_INACTIVE); |
| } |
| |
| mpc83xx_spi_setup_transfer(spi, NULL); |
| |
| spin_lock_irq(&mpc83xx_spi->lock); |
| } |
| mpc83xx_spi->busy = 0; |
| spin_unlock_irq(&mpc83xx_spi->lock); |
| } |
| |
| /* the spi->mode bits understood by this driver: */ |
| #define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \ |
| | SPI_LSB_FIRST | SPI_LOOP) |
| |
| static int mpc83xx_spi_setup(struct spi_device *spi) |
| { |
| struct mpc83xx_spi *mpc83xx_spi; |
| int retval; |
| u32 hw_mode; |
| struct spi_mpc83xx_cs *cs = spi->controller_state; |
| |
| if (spi->mode & ~MODEBITS) { |
| dev_dbg(&spi->dev, "setup: unsupported mode bits %x\n", |
| spi->mode & ~MODEBITS); |
| return -EINVAL; |
| } |
| |
| if (!spi->max_speed_hz) |
| return -EINVAL; |
| |
| if (!cs) { |
| cs = kzalloc(sizeof *cs, GFP_KERNEL); |
| if (!cs) |
| return -ENOMEM; |
| spi->controller_state = cs; |
| } |
| mpc83xx_spi = spi_master_get_devdata(spi->master); |
| |
| if (!spi->bits_per_word) |
| spi->bits_per_word = 8; |
| |
| hw_mode = cs->hw_mode; /* Save orginal settings */ |
| cs->hw_mode = mpc83xx_spi_read_reg(&mpc83xx_spi->base->mode); |
| /* mask out bits we are going to set */ |
| cs->hw_mode &= ~(SPMODE_CP_BEGIN_EDGECLK | SPMODE_CI_INACTIVEHIGH |
| | SPMODE_REV | SPMODE_LOOP); |
| |
| if (spi->mode & SPI_CPHA) |
| cs->hw_mode |= SPMODE_CP_BEGIN_EDGECLK; |
| if (spi->mode & SPI_CPOL) |
| cs->hw_mode |= SPMODE_CI_INACTIVEHIGH; |
| if (!(spi->mode & SPI_LSB_FIRST)) |
| cs->hw_mode |= SPMODE_REV; |
| if (spi->mode & SPI_LOOP) |
| cs->hw_mode |= SPMODE_LOOP; |
| |
| retval = mpc83xx_spi_setup_transfer(spi, NULL); |
| if (retval < 0) { |
| cs->hw_mode = hw_mode; /* Restore settings */ |
| return retval; |
| } |
| |
| dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u Hz\n", |
| __func__, spi->mode & (SPI_CPOL | SPI_CPHA), |
| spi->bits_per_word, spi->max_speed_hz); |
| #if 0 /* Don't think this is needed */ |
| /* NOTE we _need_ to call chipselect() early, ideally with adapter |
| * setup, unless the hardware defaults cooperate to avoid confusion |
| * between normal (active low) and inverted chipselects. |
| */ |
| |
| /* deselect chip (low or high) */ |
| spin_lock(&mpc83xx_spi->lock); |
| if (!mpc83xx_spi->busy) |
| mpc83xx_spi_chipselect(spi, BITBANG_CS_INACTIVE); |
| spin_unlock(&mpc83xx_spi->lock); |
| #endif |
| return 0; |
| } |
| |
| static irqreturn_t mpc83xx_spi_irq(s32 irq, void *context_data) |
| { |
| struct mpc83xx_spi *mpc83xx_spi = context_data; |
| u32 event; |
| irqreturn_t ret = IRQ_NONE; |
| |
| /* Get interrupt events(tx/rx) */ |
| event = mpc83xx_spi_read_reg(&mpc83xx_spi->base->event); |
| |
| /* We need handle RX first */ |
| if (event & SPIE_NE) { |
| u32 rx_data = mpc83xx_spi_read_reg(&mpc83xx_spi->base->receive); |
| |
| if (mpc83xx_spi->rx) |
| mpc83xx_spi->get_rx(rx_data, mpc83xx_spi); |
| |
| ret = IRQ_HANDLED; |
| } |
| |
| if ((event & SPIE_NF) == 0) |
| /* spin until TX is done */ |
| while (((event = |
| mpc83xx_spi_read_reg(&mpc83xx_spi->base->event)) & |
| SPIE_NF) == 0) |
| cpu_relax(); |
| |
| mpc83xx_spi->count -= 1; |
| if (mpc83xx_spi->count) { |
| u32 word = mpc83xx_spi->get_tx(mpc83xx_spi); |
| mpc83xx_spi_write_reg(&mpc83xx_spi->base->transmit, word); |
| } else { |
| complete(&mpc83xx_spi->done); |
| } |
| |
| /* Clear the events */ |
| mpc83xx_spi_write_reg(&mpc83xx_spi->base->event, event); |
| |
| return ret; |
| } |
| static int mpc83xx_spi_transfer(struct spi_device *spi, |
| struct spi_message *m) |
| { |
| struct mpc83xx_spi *mpc83xx_spi = spi_master_get_devdata(spi->master); |
| unsigned long flags; |
| |
| m->actual_length = 0; |
| m->status = -EINPROGRESS; |
| |
| spin_lock_irqsave(&mpc83xx_spi->lock, flags); |
| list_add_tail(&m->queue, &mpc83xx_spi->queue); |
| queue_work(mpc83xx_spi->workqueue, &mpc83xx_spi->work); |
| spin_unlock_irqrestore(&mpc83xx_spi->lock, flags); |
| |
| return 0; |
| } |
| |
| |
| static void mpc83xx_spi_cleanup(struct spi_device *spi) |
| { |
| kfree(spi->controller_state); |
| } |
| |
| static int __init mpc83xx_spi_probe(struct platform_device *dev) |
| { |
| struct spi_master *master; |
| struct mpc83xx_spi *mpc83xx_spi; |
| struct fsl_spi_platform_data *pdata; |
| struct resource *r; |
| u32 regval; |
| int ret = 0; |
| |
| /* Get resources(memory, IRQ) associated with the device */ |
| master = spi_alloc_master(&dev->dev, sizeof(struct mpc83xx_spi)); |
| |
| if (master == NULL) { |
| ret = -ENOMEM; |
| goto err; |
| } |
| |
| platform_set_drvdata(dev, master); |
| pdata = dev->dev.platform_data; |
| |
| if (pdata == NULL) { |
| ret = -ENODEV; |
| goto free_master; |
| } |
| |
| r = platform_get_resource(dev, IORESOURCE_MEM, 0); |
| if (r == NULL) { |
| ret = -ENODEV; |
| goto free_master; |
| } |
| master->setup = mpc83xx_spi_setup; |
| master->transfer = mpc83xx_spi_transfer; |
| master->cleanup = mpc83xx_spi_cleanup; |
| |
| mpc83xx_spi = spi_master_get_devdata(master); |
| mpc83xx_spi->qe_mode = pdata->qe_mode; |
| mpc83xx_spi->get_rx = mpc83xx_spi_rx_buf_u8; |
| mpc83xx_spi->get_tx = mpc83xx_spi_tx_buf_u8; |
| mpc83xx_spi->spibrg = pdata->sysclk; |
| |
| mpc83xx_spi->rx_shift = 0; |
| mpc83xx_spi->tx_shift = 0; |
| if (mpc83xx_spi->qe_mode) { |
| mpc83xx_spi->rx_shift = 16; |
| mpc83xx_spi->tx_shift = 24; |
| } |
| |
| init_completion(&mpc83xx_spi->done); |
| |
| mpc83xx_spi->base = ioremap(r->start, r->end - r->start + 1); |
| if (mpc83xx_spi->base == NULL) { |
| ret = -ENOMEM; |
| goto put_master; |
| } |
| |
| mpc83xx_spi->irq = platform_get_irq(dev, 0); |
| |
| if (mpc83xx_spi->irq < 0) { |
| ret = -ENXIO; |
| goto unmap_io; |
| } |
| |
| /* Register for SPI Interrupt */ |
| ret = request_irq(mpc83xx_spi->irq, mpc83xx_spi_irq, |
| 0, "mpc83xx_spi", mpc83xx_spi); |
| |
| if (ret != 0) |
| goto unmap_io; |
| |
| master->bus_num = pdata->bus_num; |
| master->num_chipselect = pdata->max_chipselect; |
| |
| /* SPI controller initializations */ |
| mpc83xx_spi_write_reg(&mpc83xx_spi->base->mode, 0); |
| mpc83xx_spi_write_reg(&mpc83xx_spi->base->mask, 0); |
| mpc83xx_spi_write_reg(&mpc83xx_spi->base->command, 0); |
| mpc83xx_spi_write_reg(&mpc83xx_spi->base->event, 0xffffffff); |
| |
| /* Enable SPI interface */ |
| regval = pdata->initial_spmode | SPMODE_INIT_VAL | SPMODE_ENABLE; |
| if (pdata->qe_mode) |
| regval |= SPMODE_OP; |
| |
| mpc83xx_spi_write_reg(&mpc83xx_spi->base->mode, regval); |
| spin_lock_init(&mpc83xx_spi->lock); |
| init_completion(&mpc83xx_spi->done); |
| INIT_WORK(&mpc83xx_spi->work, mpc83xx_spi_work); |
| INIT_LIST_HEAD(&mpc83xx_spi->queue); |
| |
| mpc83xx_spi->workqueue = create_singlethread_workqueue( |
| dev_name(master->dev.parent)); |
| if (mpc83xx_spi->workqueue == NULL) { |
| ret = -EBUSY; |
| goto free_irq; |
| } |
| |
| ret = spi_register_master(master); |
| if (ret < 0) |
| goto unreg_master; |
| |
| printk(KERN_INFO |
| "%s: MPC83xx SPI Controller driver at 0x%p (irq = %d)\n", |
| dev_name(&dev->dev), mpc83xx_spi->base, mpc83xx_spi->irq); |
| |
| return ret; |
| |
| unreg_master: |
| destroy_workqueue(mpc83xx_spi->workqueue); |
| free_irq: |
| free_irq(mpc83xx_spi->irq, mpc83xx_spi); |
| unmap_io: |
| iounmap(mpc83xx_spi->base); |
| put_master: |
| spi_master_put(master); |
| free_master: |
| kfree(master); |
| err: |
| return ret; |
| } |
| |
| static int __exit mpc83xx_spi_remove(struct platform_device *dev) |
| { |
| struct mpc83xx_spi *mpc83xx_spi; |
| struct spi_master *master; |
| |
| master = platform_get_drvdata(dev); |
| mpc83xx_spi = spi_master_get_devdata(master); |
| |
| flush_workqueue(mpc83xx_spi->workqueue); |
| destroy_workqueue(mpc83xx_spi->workqueue); |
| spi_unregister_master(master); |
| |
| free_irq(mpc83xx_spi->irq, mpc83xx_spi); |
| iounmap(mpc83xx_spi->base); |
| |
| return 0; |
| } |
| |
| MODULE_ALIAS("platform:mpc83xx_spi"); |
| static struct platform_driver mpc83xx_spi_driver = { |
| .remove = __exit_p(mpc83xx_spi_remove), |
| .driver = { |
| .name = "mpc83xx_spi", |
| .owner = THIS_MODULE, |
| }, |
| }; |
| |
| static int __init mpc83xx_spi_init(void) |
| { |
| return platform_driver_probe(&mpc83xx_spi_driver, mpc83xx_spi_probe); |
| } |
| |
| static void __exit mpc83xx_spi_exit(void) |
| { |
| platform_driver_unregister(&mpc83xx_spi_driver); |
| } |
| |
| module_init(mpc83xx_spi_init); |
| module_exit(mpc83xx_spi_exit); |
| |
| MODULE_AUTHOR("Kumar Gala"); |
| MODULE_DESCRIPTION("Simple MPC83xx SPI Driver"); |
| MODULE_LICENSE("GPL"); |