Documentation/admin-guide/media/rkisp1.rst - linux - Git at Google

 .. SPDX-License-Identifier: GPL-2.0

 .. include:: <isonum.txt>

 =========================================
 Rockchip Image Signal Processor (rkisp1)
 =========================================

 Introduction
 ============

 This file documents the driver for the Rockchip ISP1 that is part of RK3288
 and RK3399 SoCs. The driver is located under drivers/staging/media/rkisp1
 and uses the Media-Controller API.

 Revisions
 =========

 There exist multiple smaller revisions to this ISP that got introduced in
 later SoCs. Revisions can be found in the enum :c:type:`rkisp1_cif_isp_version`
 in the UAPI and the revision of the ISP inside the running SoC can be read
 in the field hw_revision of struct media_device_info as returned by
 ioctl MEDIA_IOC_DEVICE_INFO.

 Versions in use are:

 - RKISP1_V10: used at least in rk3288 and rk3399
 - RKISP1_V11: declared in the original vendor code, but not used
 - RKISP1_V12: used at least in rk3326 and px30
 - RKISP1_V13: used at least in rk1808

 Topology
 ========
 .. _rkisp1_topology_graph:

 .. kernel-figure:: rkisp1.dot
     :alt:   Diagram of the default media pipeline topology
     :align: center


 The driver has 4 video devices:

 - rkisp1_mainpath: capture device for retrieving images, usually in higher
   resolution.
 - rkisp1_selfpath: capture device for retrieving images.
 - rkisp1_stats: a metadata capture device that sends statistics.
 - rkisp1_params: a metadata output device that receives parameters
   configurations from userspace.

 The driver has 3 subdevices:

 - rkisp1_resizer_mainpath: used to resize and downsample frames for the
   mainpath capture device.
 - rkisp1_resizer_selfpath: used to resize and downsample frames for the
   selfpath capture device.
 - rkisp1_isp: is connected to the sensor and is responsible for all the isp
   operations.


 rkisp1_mainpath, rkisp1_selfpath - Frames Capture Video Nodes
 -------------------------------------------------------------
 Those are the `mainpath` and `selfpath` capture devices to capture frames.
 Those entities are the DMA engines that write the frames to memory.
 The selfpath video device can capture YUV/RGB formats. Its input is YUV encoded
 stream and it is able to convert it to RGB. The selfpath is not able to
 capture bayer formats.
 The mainpath can capture both bayer and YUV formats but it is not able to
 capture RGB formats.
 Both capture videos support
 the ``V4L2_CAP_IO_MC`` :ref:`capability <device-capabilities>`.


 rkisp1_resizer_mainpath, rkisp1_resizer_selfpath - Resizers Subdevices Nodes
 ----------------------------------------------------------------------------
 Those are resizer entities for the mainpath and the selfpath. Those entities
 can scale the frames up and down and also change the YUV sampling (for example
 YUV4:2:2 -> YUV4:2:0). They also have cropping capability on the sink pad.
 The resizers entities can only operate on YUV:4:2:2 format
 (MEDIA_BUS_FMT_YUYV8_2X8).
 The mainpath capture device supports capturing video in bayer formats. In that
 case the resizer of the mainpath is set to 'bypass' mode - it just forward the
 frame without operating on it.

 rkisp1_isp - Image Signal Processing Subdevice Node
 ---------------------------------------------------
 This is the isp entity. It is connected to the sensor on sink pad 0 and
 receives the frames using the CSI-2 protocol. It is responsible of configuring
 the CSI-2 protocol. It has a cropping capability on sink pad 0 that is
 connected to the sensor and on source pad 2 connected to the resizer entities.
 Cropping on sink pad 0 defines the image region from the sensor.
 Cropping on source pad 2 defines the region for the Image Stabilizer (IS).

 .. _rkisp1_stats:

 rkisp1_stats - Statistics Video Node
 ------------------------------------
 The statistics video node outputs the 3A (auto focus, auto exposure and auto
 white balance) statistics, and also histogram statistics for the frames that
 are being processed by the rkisp1 to userspace applications.
 Using these data, applications can implement algorithms and re-parameterize
 the driver through the rkisp_params node to improve image quality during a
 video stream.
 The buffer format is defined by struct :c:type:`rkisp1_stat_buffer`, and
 userspace should set
 :ref:`V4L2_META_FMT_RK_ISP1_STAT_3A <v4l2-meta-fmt-rk-isp1-stat-3a>` as the
 dataformat.

 .. _rkisp1_params:

 rkisp1_params - Parameters Video Node
 -------------------------------------
 The rkisp1_params video node receives a set of parameters from userspace
 to be applied to the hardware during a video stream, allowing userspace
 to dynamically modify values such as black level, cross talk corrections
 and others.

 The buffer format is defined by struct :c:type:`rkisp1_params_cfg`, and
 userspace should set
 :ref:`V4L2_META_FMT_RK_ISP1_PARAMS <v4l2-meta-fmt-rk-isp1-params>` as the
 dataformat.


 Capturing Video Frames Example
 ==============================

 In the following example, the sensor connected to pad 0 of 'rkisp1_isp' is
 imx219.

 The following commands can be used to capture video from the selfpath video
 node with dimension 900x800 planar format YUV 4:2:2. It uses all cropping
 capabilities possible, (see explanation right below)

 .. code-block:: bash

 	# set the links
 	"media-ctl" "-d" "platform:rkisp1" "-r"
 	"media-ctl" "-d" "platform:rkisp1" "-l" "'imx219 4-0010':0 -> 'rkisp1_isp':0 [1]"
 	"media-ctl" "-d" "platform:rkisp1" "-l" "'rkisp1_isp':2 -> 'rkisp1_resizer_selfpath':0 [1]"
 	"media-ctl" "-d" "platform:rkisp1" "-l" "'rkisp1_isp':2 -> 'rkisp1_resizer_mainpath':0 [0]"

 	# set format for imx219 4-0010:0
 	"media-ctl" "-d" "platform:rkisp1" "--set-v4l2" '"imx219 4-0010":0 [fmt:SRGGB10_1X10/1640x1232]'

 	# set format for rkisp1_isp pads:
 	"media-ctl" "-d" "platform:rkisp1" "--set-v4l2" '"rkisp1_isp":0 [fmt:SRGGB10_1X10/1640x1232 crop: (0,0)/1600x1200]'
 	"media-ctl" "-d" "platform:rkisp1" "--set-v4l2" '"rkisp1_isp":2 [fmt:YUYV8_2X8/1600x1200 crop: (0,0)/1500x1100]'

 	# set format for rkisp1_resizer_selfpath pads:
 	"media-ctl" "-d" "platform:rkisp1" "--set-v4l2" '"rkisp1_resizer_selfpath":0 [fmt:YUYV8_2X8/1500x1100 crop: (300,400)/1400x1000]'
 	"media-ctl" "-d" "platform:rkisp1" "--set-v4l2" '"rkisp1_resizer_selfpath":1 [fmt:YUYV8_2X8/900x800]'

 	# set format for rkisp1_selfpath:
 	"v4l2-ctl" "-z" "platform:rkisp1" "-d" "rkisp1_selfpath" "-v" "width=900,height=800,"
 	"v4l2-ctl" "-z" "platform:rkisp1" "-d" "rkisp1_selfpath" "-v" "pixelformat=422P"

 	# start streaming:
 	v4l2-ctl "-z" "platform:rkisp1" "-d" "rkisp1_selfpath" "--stream-mmap" "--stream-count" "10"


 In the above example the sensor is configured to bayer format:
 `SRGGB10_1X10/1640x1232`. The rkisp1_isp:0 pad should be configured to the
 same mbus format and dimensions as the sensor, otherwise streaming will fail
 with 'EPIPE' error. So it is also configured to `SRGGB10_1X10/1640x1232`.
 In addition, the rkisp1_isp:0 pad is configured to cropping `(0,0)/1600x1200`.

 The cropping dimensions are automatically propagated to be the format of the
 isp source pad `rkisp1_isp:2`. Another cropping operation is configured on
 the isp source pad: `(0,0)/1500x1100`.

 The resizer's sink pad `rkisp1_resizer_selfpath` should be configured to format
 `YUYV8_2X8/1500x1100` in order to match the format on the other side of the
 link. In addition a cropping `(300,400)/1400x1000` is configured on it.

 The source pad of the resizer, `rkisp1_resizer_selfpath:1` is configured to
 format `YUYV8_2X8/900x800`. That means that the resizer first crop a window
 of `(300,400)/1400x100` from the received frame and then scales this window
 to dimension `900x800`.

 Note that the above example does not uses the stats-params control loop.
 Therefore the capture frames will not go through the 3A algorithms and
 probably won't have a good quality, and can even look dark and greenish.

 Configuring Quantization
 ========================

 The driver supports limited and full range quantization on YUV formats,
 where limited is the default.
 To switch between one or the other, userspace should use the Colorspace
 Conversion API (CSC) for subdevices on source pad 2 of the
 isp (`rkisp1_isp:2`). The quantization configured on this pad is the
 quantization of the captured video frames on the mainpath and selfpath
 video nodes.
 Note that the resizer and capture entities will always report
 ``V4L2_QUANTIZATION_DEFAULT`` even if the quantization is configured to full
 range on `rkisp1_isp:2`. So in order to get the configured quantization,
 application should get it from pad `rkisp1_isp:2`.
	.. SPDX-License-Identifier: GPL-2.0

	.. include:: <isonum.txt>

	=========================================
	Rockchip Image Signal Processor (rkisp1)
	=========================================

	Introduction
	============

	This file documents the driver for the Rockchip ISP1 that is part of RK3288
	and RK3399 SoCs. The driver is located under drivers/staging/media/rkisp1
	and uses the Media-Controller API.

	Revisions
	=========

	There exist multiple smaller revisions to this ISP that got introduced in
	later SoCs. Revisions can be found in the enum :c:type:`rkisp1_cif_isp_version`
	in the UAPI and the revision of the ISP inside the running SoC can be read
	in the field hw_revision of struct media_device_info as returned by
	ioctl MEDIA_IOC_DEVICE_INFO.

	Versions in use are:

	- RKISP1_V10: used at least in rk3288 and rk3399
	- RKISP1_V11: declared in the original vendor code, but not used
	- RKISP1_V12: used at least in rk3326 and px30
	- RKISP1_V13: used at least in rk1808

	Topology
	========
	.. _rkisp1_topology_graph:

	.. kernel-figure:: rkisp1.dot
	:alt: Diagram of the default media pipeline topology
	:align: center


	The driver has 4 video devices:

	- rkisp1_mainpath: capture device for retrieving images, usually in higher
	resolution.
	- rkisp1_selfpath: capture device for retrieving images.
	- rkisp1_stats: a metadata capture device that sends statistics.
	- rkisp1_params: a metadata output device that receives parameters
	configurations from userspace.

	The driver has 3 subdevices:

	- rkisp1_resizer_mainpath: used to resize and downsample frames for the
	mainpath capture device.
	- rkisp1_resizer_selfpath: used to resize and downsample frames for the
	selfpath capture device.
	- rkisp1_isp: is connected to the sensor and is responsible for all the isp
	operations.


	rkisp1_mainpath, rkisp1_selfpath - Frames Capture Video Nodes
	-------------------------------------------------------------
	Those are the `mainpath` and `selfpath` capture devices to capture frames.
	Those entities are the DMA engines that write the frames to memory.
	The selfpath video device can capture YUV/RGB formats. Its input is YUV encoded
	stream and it is able to convert it to RGB. The selfpath is not able to
	capture bayer formats.
	The mainpath can capture both bayer and YUV formats but it is not able to
	capture RGB formats.
	Both capture videos support
	the ``V4L2_CAP_IO_MC`` :ref:`capability <device-capabilities>`.


	rkisp1_resizer_mainpath, rkisp1_resizer_selfpath - Resizers Subdevices Nodes
	----------------------------------------------------------------------------
	Those are resizer entities for the mainpath and the selfpath. Those entities
	can scale the frames up and down and also change the YUV sampling (for example
	YUV4:2:2 -> YUV4:2:0). They also have cropping capability on the sink pad.
	The resizers entities can only operate on YUV:4:2:2 format
	(MEDIA_BUS_FMT_YUYV8_2X8).
	The mainpath capture device supports capturing video in bayer formats. In that
	case the resizer of the mainpath is set to 'bypass' mode - it just forward the
	frame without operating on it.

	rkisp1_isp - Image Signal Processing Subdevice Node
	---------------------------------------------------
	This is the isp entity. It is connected to the sensor on sink pad 0 and
	receives the frames using the CSI-2 protocol. It is responsible of configuring
	the CSI-2 protocol. It has a cropping capability on sink pad 0 that is
	connected to the sensor and on source pad 2 connected to the resizer entities.
	Cropping on sink pad 0 defines the image region from the sensor.
	Cropping on source pad 2 defines the region for the Image Stabilizer (IS).

	.. _rkisp1_stats:

	rkisp1_stats - Statistics Video Node
	------------------------------------
	The statistics video node outputs the 3A (auto focus, auto exposure and auto
	white balance) statistics, and also histogram statistics for the frames that
	are being processed by the rkisp1 to userspace applications.
	Using these data, applications can implement algorithms and re-parameterize
	the driver through the rkisp_params node to improve image quality during a
	video stream.
	The buffer format is defined by struct :c:type:`rkisp1_stat_buffer`, and
	userspace should set
	:ref:`V4L2_META_FMT_RK_ISP1_STAT_3A <v4l2-meta-fmt-rk-isp1-stat-3a>` as the
	dataformat.

	.. _rkisp1_params:

	rkisp1_params - Parameters Video Node
	-------------------------------------
	The rkisp1_params video node receives a set of parameters from userspace
	to be applied to the hardware during a video stream, allowing userspace
	to dynamically modify values such as black level, cross talk corrections
	and others.

	The buffer format is defined by struct :c:type:`rkisp1_params_cfg`, and
	userspace should set
	:ref:`V4L2_META_FMT_RK_ISP1_PARAMS <v4l2-meta-fmt-rk-isp1-params>` as the
	dataformat.


	Capturing Video Frames Example
	==============================

	In the following example, the sensor connected to pad 0 of 'rkisp1_isp' is
	imx219.

	The following commands can be used to capture video from the selfpath video
	node with dimension 900x800 planar format YUV 4:2:2. It uses all cropping
	capabilities possible, (see explanation right below)

	.. code-block:: bash

	# set the links
	"media-ctl" "-d" "platform:rkisp1" "-r"
	"media-ctl" "-d" "platform:rkisp1" "-l" "'imx219 4-0010':0 -> 'rkisp1_isp':0 [1]"
	"media-ctl" "-d" "platform:rkisp1" "-l" "'rkisp1_isp':2 -> 'rkisp1_resizer_selfpath':0 [1]"
	"media-ctl" "-d" "platform:rkisp1" "-l" "'rkisp1_isp':2 -> 'rkisp1_resizer_mainpath':0 [0]"

	# set format for imx219 4-0010:0
	"media-ctl" "-d" "platform:rkisp1" "--set-v4l2" '"imx219 4-0010":0 [fmt:SRGGB10_1X10/1640x1232]'

	# set format for rkisp1_isp pads:
	"media-ctl" "-d" "platform:rkisp1" "--set-v4l2" '"rkisp1_isp":0 [fmt:SRGGB10_1X10/1640x1232 crop: (0,0)/1600x1200]'
	"media-ctl" "-d" "platform:rkisp1" "--set-v4l2" '"rkisp1_isp":2 [fmt:YUYV8_2X8/1600x1200 crop: (0,0)/1500x1100]'

	# set format for rkisp1_resizer_selfpath pads:
	"media-ctl" "-d" "platform:rkisp1" "--set-v4l2" '"rkisp1_resizer_selfpath":0 [fmt:YUYV8_2X8/1500x1100 crop: (300,400)/1400x1000]'
	"media-ctl" "-d" "platform:rkisp1" "--set-v4l2" '"rkisp1_resizer_selfpath":1 [fmt:YUYV8_2X8/900x800]'

	# set format for rkisp1_selfpath:
	"v4l2-ctl" "-z" "platform:rkisp1" "-d" "rkisp1_selfpath" "-v" "width=900,height=800,"
	"v4l2-ctl" "-z" "platform:rkisp1" "-d" "rkisp1_selfpath" "-v" "pixelformat=422P"

	# start streaming:
	v4l2-ctl "-z" "platform:rkisp1" "-d" "rkisp1_selfpath" "--stream-mmap" "--stream-count" "10"


	In the above example the sensor is configured to bayer format:
	`SRGGB10_1X10/1640x1232`. The rkisp1_isp:0 pad should be configured to the
	same mbus format and dimensions as the sensor, otherwise streaming will fail
	with 'EPIPE' error. So it is also configured to `SRGGB10_1X10/1640x1232`.
	In addition, the rkisp1_isp:0 pad is configured to cropping `(0,0)/1600x1200`.

	The cropping dimensions are automatically propagated to be the format of the
	isp source pad `rkisp1_isp:2`. Another cropping operation is configured on
	the isp source pad: `(0,0)/1500x1100`.

	The resizer's sink pad `rkisp1_resizer_selfpath` should be configured to format
	`YUYV8_2X8/1500x1100` in order to match the format on the other side of the
	link. In addition a cropping `(300,400)/1400x1000` is configured on it.

	The source pad of the resizer, `rkisp1_resizer_selfpath:1` is configured to
	format `YUYV8_2X8/900x800`. That means that the resizer first crop a window
	of `(300,400)/1400x100` from the received frame and then scales this window
	to dimension `900x800`.

	Note that the above example does not uses the stats-params control loop.
	Therefore the capture frames will not go through the 3A algorithms and
	probably won't have a good quality, and can even look dark and greenish.

	Configuring Quantization
	========================

	The driver supports limited and full range quantization on YUV formats,
	where limited is the default.
	To switch between one or the other, userspace should use the Colorspace
	Conversion API (CSC) for subdevices on source pad 2 of the
	isp (`rkisp1_isp:2`). The quantization configured on this pad is the
	quantization of the captured video frames on the mainpath and selfpath
	video nodes.
	Note that the resizer and capture entities will always report
	``V4L2_QUANTIZATION_DEFAULT`` even if the quantization is configured to full
	range on `rkisp1_isp:2`. So in order to get the configured quantization,
	application should get it from pad `rkisp1_isp:2`.