| # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) |
| %YAML 1.2 |
| --- |
| $id: "http://devicetree.org/schemas/remoteproc/st,stm32-rproc.yaml#" |
| $schema: "http://devicetree.org/meta-schemas/core.yaml#" |
| |
| title: STMicroelectronics STM32 remote processor controller bindings |
| |
| description: |
| This document defines the binding for the remoteproc component that loads and |
| boots firmwares on the ST32MP family chipset. |
| |
| maintainers: |
| - Fabien Dessenne <fabien.dessenne@st.com> |
| - Arnaud Pouliquen <arnaud.pouliquen@st.com> |
| |
| properties: |
| compatible: |
| const: st,stm32mp1-m4 |
| |
| reg: |
| description: |
| Address ranges of the RETRAM and MCU SRAM memories used by the remote |
| processor. |
| maxItems: 3 |
| |
| resets: |
| maxItems: 1 |
| |
| st,syscfg-holdboot: |
| description: remote processor reset hold boot |
| - Phandle of syscon block. |
| - The offset of the hold boot setting register. |
| - The field mask of the hold boot. |
| $ref: "/schemas/types.yaml#/definitions/phandle-array" |
| maxItems: 1 |
| |
| st,syscfg-tz: |
| description: |
| Reference to the system configuration which holds the RCC trust zone mode |
| $ref: "/schemas/types.yaml#/definitions/phandle-array" |
| maxItems: 1 |
| |
| interrupts: |
| description: Should contain the WWDG1 watchdog reset interrupt |
| maxItems: 1 |
| |
| wakeup-source: true |
| |
| mboxes: |
| description: |
| This property is required only if the rpmsg/virtio functionality is used. |
| items: |
| - description: | |
| A channel (a) used to communicate through virtqueues with the |
| remote proc. |
| Bi-directional channel: |
| - from local to remote = send message |
| - from remote to local = send message ack |
| - description: | |
| A channel (b) working the opposite direction of channel (a) |
| - description: | |
| A channel (c) used by the local proc to notify the remote proc that it |
| is about to be shut down. |
| Unidirectional channel: |
| - from local to remote, where ACK from the remote means that it is |
| ready for shutdown |
| - description: | |
| A channel (d) used by the local proc to notify the remote proc that it |
| has to stop interprocessor communnication. |
| Unidirectional channel: |
| - from local to remote, where ACK from the remote means that communnication |
| as been stopped on the remote side. |
| minItems: 1 |
| |
| mbox-names: |
| items: |
| - const: vq0 |
| - const: vq1 |
| - const: shutdown |
| - const: detach |
| minItems: 1 |
| |
| memory-region: |
| description: |
| List of phandles to the reserved memory regions associated with the |
| remoteproc device. This is variable and describes the memories shared with |
| the remote processor (e.g. remoteproc firmware and carveouts, rpmsg |
| vrings, ...). |
| (see ../reserved-memory/reserved-memory.txt) |
| |
| st,syscfg-pdds: |
| $ref: "/schemas/types.yaml#/definitions/phandle-array" |
| description: | |
| Reference to the system configuration which holds the remote |
| maxItems: 1 |
| |
| st,syscfg-m4-state: |
| $ref: "/schemas/types.yaml#/definitions/phandle-array" |
| description: | |
| Reference to the tamp register which exposes the Cortex-M4 state. |
| maxItems: 1 |
| |
| st,syscfg-rsc-tbl: |
| $ref: "/schemas/types.yaml#/definitions/phandle-array" |
| description: | |
| Reference to the tamp register which references the Cortex-M4 |
| resource table address. |
| maxItems: 1 |
| |
| st,auto-boot: |
| $ref: /schemas/types.yaml#/definitions/flag |
| description: |
| If defined, when remoteproc is probed, it loads the default firmware and |
| starts the remote processor. |
| |
| required: |
| - compatible |
| - reg |
| - resets |
| - st,syscfg-holdboot |
| - st,syscfg-tz |
| |
| additionalProperties: false |
| |
| examples: |
| - | |
| #include <dt-bindings/reset/stm32mp1-resets.h> |
| m4_rproc: m4@10000000 { |
| compatible = "st,stm32mp1-m4"; |
| reg = <0x10000000 0x40000>, |
| <0x30000000 0x40000>, |
| <0x38000000 0x10000>; |
| resets = <&rcc MCU_R>; |
| st,syscfg-holdboot = <&rcc 0x10C 0x1>; |
| st,syscfg-tz = <&rcc 0x000 0x1>; |
| st,syscfg-rsc-tbl = <&tamp 0x144 0xFFFFFFFF>; |
| st,syscfg-m4-state = <&tamp 0x148 0xFFFFFFFF>; |
| }; |
| |
| ... |
