| /* |
| * pdu001.dts |
| * |
| * EETS GmbH PDU001 board device tree file |
| * |
| * Copyright (C) 2018 EETS GmbH - http://www.eets.ch/ |
| * |
| * Copyright (C) 2011, Texas Instruments, Incorporated - https://www.ti.com/ |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /dts-v1/; |
| |
| #include "am33xx.dtsi" |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/leds/leds-pca9532.h> |
| |
| / { |
| model = "EETS,PDU001"; |
| compatible = "ti,am33xx"; |
| |
| chosen { |
| stdout-path = &uart3; |
| }; |
| |
| cpus { |
| cpu@0 { |
| cpu0-supply = <&vdd1_reg>; |
| }; |
| }; |
| |
| memory { |
| device_type = "memory"; |
| reg = <0x80000000 0x10000000>; /* 256 MB */ |
| }; |
| |
| vbat: fixedregulator@0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vbat"; |
| regulator-min-microvolt = <3600000>; |
| regulator-max-microvolt = <3600000>; |
| regulator-boot-on; |
| }; |
| |
| lis3_reg: fixedregulator@1 { |
| compatible = "regulator-fixed"; |
| regulator-name = "lis3_reg"; |
| regulator-boot-on; |
| }; |
| |
| panel { |
| compatible = "ti,tilcdc,panel"; |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&lcd_pins_s0>; |
| panel-info { |
| ac-bias = <255>; |
| ac-bias-intrpt = <0>; |
| dma-burst-sz = <16>; |
| bpp = <16>; |
| fdd = <0x80>; |
| sync-edge = <0>; |
| sync-ctrl = <1>; |
| raster-order = <0>; |
| fifo-th = <0>; |
| }; |
| |
| display-timings { |
| 240x320p16 { |
| clock-frequency = <6500000>; |
| hactive = <240>; |
| vactive = <320>; |
| hfront-porch = <6>; |
| hback-porch = <6>; |
| hsync-len = <1>; |
| vback-porch = <6>; |
| vfront-porch = <6>; |
| vsync-len = <1>; |
| hsync-active = <0>; |
| vsync-active = <0>; |
| pixelclk-active = <1>; |
| de-active = <0>; |
| }; |
| }; |
| }; |
| }; |
| |
| &am33xx_pinmux { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&clkout2_pin>; |
| |
| i2c0_pins: pinmux_i2c0_pins { |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0) |
| >; |
| }; |
| |
| i2c1_pins: pinmux_i2c1_pins { |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLUP, MUX_MODE2) /* spi0_d1.i2c1_sda */ |
| AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLUP, MUX_MODE2) /* spi0_cs0.i2c1_scl */ |
| >; |
| }; |
| |
| i2c2_pins: pinmux_i2c2_pins { |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE2) /* spi0_clk.i2c2_sda */ |
| AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT_PULLUP, MUX_MODE2) /* spi0_d0.i2c2_scl */ |
| >; |
| }; |
| |
| spi1_pins: pinmux_spi1_pins { |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT, MUX_MODE3) /* mcasp0_aclkx.spi1_sclk */ |
| AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT, MUX_MODE3) /* mcasp0_fsx.spi1_d0 */ |
| AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR0, PIN_INPUT_PULLDOWN, MUX_MODE3) /* mcasp0_axr0.spi1_d1 */ |
| AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_OUTPUT, MUX_MODE3) /* mcasp0_ahclkr.spi1_cs0 */ |
| >; |
| }; |
| |
| uart0_pins: pinmux_uart0_pins { |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_OUTPUT, MUX_MODE7) |
| AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0) |
| >; |
| }; |
| |
| uart1_pins: pinmux_uart1_pins { |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0) |
| >; |
| }; |
| |
| uart3_pins: pinmux_uart3_pins { |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT_PULLUP, MUX_MODE1) /* spi0_cs1.uart3_rxd */ |
| AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, PIN_OUTPUT_PULLDOWN, MUX_MODE1) /* ecap0_in_pwm0_out.uart3_txd */ |
| >; |
| }; |
| |
| clkout2_pin: pinmux_clkout2_pin { |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3) /* xdma_event_intr1.clkout2 */ |
| >; |
| }; |
| |
| cpsw_default: cpsw_default { |
| pinctrl-single,pins = < |
| /* Port 1 (emac0) */ |
| AM33XX_PADCONF(AM335X_PIN_MII1_COL, PIN_INPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT, MUX_MODE0) |
| |
| /* Port 2 (emac1) */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_OUTPUT, MUX_MODE1) /* mii2_txen.gpmc_a0 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT, MUX_MODE1) /* mii2_rxdv.gpmc_a1 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT, MUX_MODE1) /* mii2_txd3.gpmc_a2 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_OUTPUT, MUX_MODE1) /* mii2_txd2.gpmc_a3 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_OUTPUT, MUX_MODE1) /* mii2_txd1.gpmc_a4 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT, MUX_MODE1) /* mii2_txd0.gpmc_a5 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_INPUT, MUX_MODE1) /* mii2_txclk.gpmc_a6 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_INPUT, MUX_MODE1) /* mii2_rxclk.gpmc_a7 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_INPUT, MUX_MODE1) /* mii2_rxd3.gpmc_a8 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT, MUX_MODE1) /* mii2_rxd2.gpmc_a9 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT, MUX_MODE1) /* mii2_rxd1.gpmc_a10 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT, MUX_MODE1) /* mii2_rxd0.gpmc_a11 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT, MUX_MODE1) /* mii2_crs.gpmc_wait0 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT, MUX_MODE1) /* mii2_rxer.gpmc_wpn */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_BEN1, PIN_INPUT, MUX_MODE1) /* mii2_col.gpmc_ben1 */ |
| >; |
| }; |
| |
| davinci_mdio_default: davinci_mdio_default { |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0) |
| >; |
| }; |
| |
| mmc1_pins: pinmux_mmc1_pins { |
| /* eMMC */ |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLUP, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLUP, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLUP, MUX_MODE0) |
| >; |
| }; |
| |
| mmc2_pins: pinmux_mmc2_pins { |
| /* SD cardcage */ |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_AD2, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn1.mmc1_clk */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ |
| /* card change signal for frontpanel SD cardcage */ |
| AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_INPUT, MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */ |
| >; |
| }; |
| |
| lcd_pins_s0: lcd_pins_s0 { |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT, MUX_MODE0) |
| AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT, MUX_MODE0) |
| >; |
| }; |
| |
| dcan0_pins: pinmux_dcan0_pins { |
| pinctrl-single,pins = < |
| AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_OUTPUT, MUX_MODE2) /* uart1_ctsn.d_can0_tx */ |
| AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE2) /* uart1_rtsn.d_can0_rx */ |
| >; |
| }; |
| }; |
| |
| &uart0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_pins>; |
| |
| rts-gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; |
| rs485-rts-active-high; |
| rs485-rts-delay = <0 0>; |
| linux,rs485-enabled-at-boot-time; |
| |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart1_pins>; |
| |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart3_pins>; |
| |
| status = "okay"; |
| }; |
| |
| &i2c0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c0_pins>; |
| |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| tps: tps@2d { |
| reg = <0x2d>; |
| }; |
| |
| m2_eeprom: m2_eeprom@50 { |
| compatible = "atmel,24c256"; |
| reg = <0x50>; |
| status = "okay"; |
| }; |
| }; |
| |
| &i2c1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c1_pins>; |
| |
| status = "okay"; |
| clock-frequency = <100000>; |
| |
| board_24aa025e48: board_24aa025e48@50 { |
| compatible = "atmel,24c02"; |
| reg = <0x50>; |
| }; |
| |
| backplane_24aa025e48: backplane_24aa025e48@53 { |
| compatible = "atmel,24c02"; |
| reg = <0x53>; |
| }; |
| |
| pca9532: pca9532@60 { |
| compatible = "nxp,pca9532"; |
| reg = <0x60>; |
| psc0 = <0x97>; |
| pwm0 = <0x80>; |
| psc1 = <0x97>; |
| pwm1 = <0x10>; |
| |
| run.red@0 { |
| type = <PCA9532_TYPE_LED>; |
| }; |
| run.green@1 { |
| type = <PCA9532_TYPE_LED>; |
| default-state = "on"; |
| }; |
| s2.red@2 { |
| type = <PCA9532_TYPE_LED>; |
| }; |
| s2.green@3 { |
| type = <PCA9532_TYPE_LED>; |
| }; |
| s1.yellow@4 { |
| type = <PCA9532_TYPE_LED>; |
| }; |
| s1.green@5 { |
| type = <PCA9532_TYPE_LED>; |
| }; |
| }; |
| |
| pca9530: pca9530@61 { |
| compatible = "nxp,pca9530"; |
| reg = <0x61>; |
| |
| tft-panel@0 { |
| type = <PCA9532_TYPE_LED>; |
| linux,default-trigger = "backlight"; |
| default-state = "on"; |
| }; |
| }; |
| |
| mcp79400: mcp79400@6f { |
| compatible = "microchip,mcp7940x"; |
| reg = <0x6f>; |
| }; |
| }; |
| |
| &i2c2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c2_pins>; |
| |
| status = "okay"; |
| clock-frequency = <100000>; |
| }; |
| |
| &spi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi1_pins>; |
| ti,pindir-d0-out-d1-in; |
| status = "okay"; |
| |
| display-controller@0 { |
| compatible = "orisetech,otm3225a"; |
| reg = <0>; |
| spi-max-frequency = <1000000>; |
| // SPI mode 3 |
| spi-cpol; |
| spi-cpha; |
| status = "okay"; |
| }; |
| }; |
| |
| /* |
| * Disable soc's rtc as we have no VBAT for it. This makes the board |
| * rtc (Microchip MCP79400) the default rtc device 'rtc0'. |
| */ |
| &rtc { |
| status = "disabled"; |
| }; |
| |
| &lcdc { |
| status = "okay"; |
| }; |
| |
| &elm { |
| status = "okay"; |
| }; |
| |
| #include "tps65910.dtsi" |
| |
| &tps { |
| vcc1-supply = <&vbat>; |
| vcc2-supply = <&vbat>; |
| vcc3-supply = <&vbat>; |
| vcc4-supply = <&vbat>; |
| vcc5-supply = <&vbat>; |
| vcc6-supply = <&vbat>; |
| vcc7-supply = <&vbat>; |
| vccio-supply = <&vbat>; |
| |
| regulators { |
| vrtc_reg: regulator@0 { |
| regulator-name = "ldo_vrtc"; |
| regulator-always-on; |
| }; |
| |
| vio_reg: regulator@1 { |
| regulator-name = "buck_vdd_ddr"; |
| regulator-always-on; |
| }; |
| |
| vdd1_reg: regulator@2 { |
| /* VDD_MPU voltage limits */ |
| regulator-name = "buck_vdd_mpu"; |
| regulator-min-microvolt = <912500>; |
| regulator-max-microvolt = <1312500>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vdd2_reg: regulator@3 { |
| /* VDD_CORE voltage limits */ |
| regulator-name = "buck_vdd_core"; |
| regulator-min-microvolt = <912500>; |
| regulator-max-microvolt = <1150000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vdd3_reg: regulator@4 { |
| regulator-name = "boost_res"; |
| regulator-always-on; |
| }; |
| |
| vdig1_reg: regulator@5 { |
| regulator-name = "ldo_vdig1"; |
| regulator-always-on; |
| }; |
| |
| vdig2_reg: regulator@6 { |
| regulator-name = "ldo_vdig2"; |
| regulator-always-on; |
| }; |
| |
| vpll_reg: regulator@7 { |
| regulator-name = "ldo_vpll"; |
| regulator-always-on; |
| }; |
| |
| vdac_reg: regulator@8 { |
| regulator-name = "ldo_vdac"; |
| regulator-always-on; |
| }; |
| |
| vaux1_reg: regulator@9 { |
| regulator-name = "ldo_vaux1"; |
| regulator-always-on; |
| }; |
| |
| vaux2_reg: regulator@10 { |
| regulator-name = "ldo_vaux2"; |
| regulator-always-on; |
| }; |
| |
| vaux33_reg: regulator@11 { |
| regulator-name = "ldo_vaux33"; |
| regulator-always-on; |
| }; |
| |
| vmmc_reg: regulator@12 { |
| regulator-name = "ldo_vmmc"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| vbb_reg: regulator@13 { |
| regulator-name = "bat_vbb"; |
| }; |
| }; |
| }; |
| |
| &mac_sw { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&cpsw_default>; |
| status = "okay"; |
| }; |
| |
| &davinci_mdio_sw { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&davinci_mdio_default>; |
| |
| ethphy0: ethernet-phy@0 { |
| reg = <0>; |
| }; |
| |
| ethphy1: ethernet-phy@1 { |
| reg = <1>; |
| }; |
| }; |
| |
| &cpsw_port1 { |
| phy-handle = <ðphy0>; |
| phy-mode = "mii"; |
| ti,dual-emac-pvid = <1>; |
| }; |
| |
| &cpsw_port2 { |
| phy-handle = <ðphy1>; |
| phy-mode = "mii"; |
| ti,dual-emac-pvid = <2>; |
| }; |
| |
| &tscadc { |
| status = "okay"; |
| tsc { |
| ti,wires = <4>; |
| ti,x-plate-resistance = <200>; |
| ti,coordinate-readouts = <5>; |
| ti,wire-config = <0x01 0x10 0x22 0x33>; |
| ti,charge-delay = <0x400>; |
| }; |
| |
| adc { |
| ti,adc-channels = <4 5 6 7>; |
| }; |
| }; |
| |
| &mmc1 { |
| status = "okay"; |
| vmmc-supply = <&vmmc_reg>; |
| bus-width = <4>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc1_pins>; |
| non-removable; |
| }; |
| |
| &mmc2 { |
| status = "okay"; |
| vmmc-supply = <&vmmc_reg>; |
| bus-width = <4>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc2_pins>; |
| cd-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| &sham { |
| status = "okay"; |
| }; |
| |
| &aes { |
| status = "okay"; |
| }; |
| |
| &dcan0 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&dcan0_pins>; |
| }; |
