| /* |
| * Copyright 2016 Gateworks Corporation |
| * |
| * This file is dual-licensed: you can use it either under the terms |
| * of the GPL or the X11 license, at your option. Note that this dual |
| * licensing only applies to this file, and not this project as a |
| * whole. |
| * |
| * a) This file is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This file is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public |
| * License along with this file; if not, write to the Free |
| * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, |
| * MA 02110-1301 USA |
| * |
| * Or, alternatively, |
| * |
| * b) Permission is hereby granted, free of charge, to any person |
| * obtaining a copy of this software and associated documentation |
| * files (the "Software"), to deal in the Software without |
| * restriction, including without limitation the rights to use, |
| * copy, modify, merge, publish, distribute, sublicense, and/or |
| * sell copies of the Software, and to permit persons to whom the |
| * Software is furnished to do so, subject to the following |
| * conditions: |
| * |
| * The above copyright notice and this permission notice shall be |
| * included in all copies or substantial portions of the Software. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, |
| * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES |
| * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND |
| * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT |
| * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, |
| * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING |
| * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR |
| * OTHER DEALINGS IN THE SOFTWARE. |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| / { |
| /* these are used by bootloader for disabling nodes */ |
| aliases { |
| led0 = &led0; |
| led1 = &led1; |
| nand = &gpmi; |
| usb0 = &usbh1; |
| usb1 = &usbotg; |
| }; |
| |
| chosen { |
| stdout-path = &uart2; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| user-pb { |
| label = "user_pb"; |
| gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>; |
| linux,code = <BTN_0>; |
| }; |
| |
| user-pb1x { |
| label = "user_pb1x"; |
| linux,code = <BTN_1>; |
| interrupt-parent = <&gsc>; |
| interrupts = <0>; |
| }; |
| |
| key-erased { |
| label = "key-erased"; |
| linux,code = <BTN_2>; |
| interrupt-parent = <&gsc>; |
| interrupts = <1>; |
| }; |
| |
| eeprom-wp { |
| label = "eeprom_wp"; |
| linux,code = <BTN_3>; |
| interrupt-parent = <&gsc>; |
| interrupts = <2>; |
| }; |
| |
| tamper { |
| label = "tamper"; |
| linux,code = <BTN_4>; |
| interrupt-parent = <&gsc>; |
| interrupts = <5>; |
| }; |
| |
| switch-hold { |
| label = "switch_hold"; |
| linux,code = <BTN_5>; |
| interrupt-parent = <&gsc>; |
| interrupts = <7>; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_leds>; |
| |
| led0: user1 { |
| label = "user1"; |
| gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */ |
| default-state = "on"; |
| linux,default-trigger = "heartbeat"; |
| }; |
| |
| led1: user2 { |
| label = "user2"; |
| gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */ |
| default-state = "off"; |
| }; |
| }; |
| |
| memory@10000000 { |
| device_type = "memory"; |
| reg = <0x10000000 0x20000000>; |
| }; |
| |
| pps { |
| compatible = "pps-gpio"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pps>; |
| gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| reg_5p0v: regulator-5p0v { |
| compatible = "regulator-fixed"; |
| regulator-name = "5P0V"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-always-on; |
| }; |
| |
| reg_usb_otg_vbus: regulator-usb-otg-vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "usb_otg_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| }; |
| |
| &gpmi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpmi_nand>; |
| status = "okay"; |
| }; |
| |
| &hdmi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_hdmi>; |
| ddc-i2c-bus = <&i2c3>; |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| |
| gsc: gsc@20 { |
| compatible = "gw,gsc"; |
| reg = <0x20>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <4 IRQ_TYPE_LEVEL_LOW>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| #size-cells = <0>; |
| |
| adc { |
| compatible = "gw,gsc-adc"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| channel@0 { |
| gw,mode = <0>; |
| reg = <0x00>; |
| label = "temp"; |
| }; |
| |
| channel@2 { |
| gw,mode = <1>; |
| reg = <0x02>; |
| label = "vdd_vin"; |
| }; |
| |
| channel@5 { |
| gw,mode = <1>; |
| reg = <0x05>; |
| label = "vdd_3p3"; |
| }; |
| |
| channel@8 { |
| gw,mode = <1>; |
| reg = <0x08>; |
| label = "vdd_bat"; |
| }; |
| |
| channel@b { |
| gw,mode = <1>; |
| reg = <0x0b>; |
| label = "vdd_5p0"; |
| }; |
| |
| channel@e { |
| gw,mode = <1>; |
| reg = <0xe>; |
| label = "vdd_arm"; |
| }; |
| |
| channel@11 { |
| gw,mode = <1>; |
| reg = <0x11>; |
| label = "vdd_soc"; |
| }; |
| |
| channel@14 { |
| gw,mode = <1>; |
| reg = <0x14>; |
| label = "vdd_3p0"; |
| }; |
| |
| channel@17 { |
| gw,mode = <1>; |
| reg = <0x17>; |
| label = "vdd_1p5"; |
| }; |
| |
| channel@1d { |
| gw,mode = <1>; |
| reg = <0x1d>; |
| label = "vdd_1p8a"; |
| }; |
| |
| channel@20 { |
| gw,mode = <1>; |
| reg = <0x20>; |
| label = "vdd_1p0b"; |
| }; |
| |
| channel@26 { |
| gw,mode = <1>; |
| reg = <0x26>; |
| label = "vdd_an1"; |
| }; |
| }; |
| }; |
| |
| gsc_gpio: gpio@23 { |
| compatible = "nxp,pca9555"; |
| reg = <0x23>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-parent = <&gsc>; |
| interrupts = <4>; |
| }; |
| |
| eeprom1: eeprom@50 { |
| compatible = "atmel,24c02"; |
| reg = <0x50>; |
| pagesize = <16>; |
| }; |
| |
| eeprom2: eeprom@51 { |
| compatible = "atmel,24c02"; |
| reg = <0x51>; |
| pagesize = <16>; |
| }; |
| |
| eeprom3: eeprom@52 { |
| compatible = "atmel,24c02"; |
| reg = <0x52>; |
| pagesize = <16>; |
| }; |
| |
| eeprom4: eeprom@53 { |
| compatible = "atmel,24c02"; |
| reg = <0x53>; |
| pagesize = <16>; |
| }; |
| |
| rtc: ds1672@68 { |
| compatible = "dallas,ds1672"; |
| reg = <0x68>; |
| }; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| status = "okay"; |
| |
| magn@1c { |
| compatible = "st,lsm9ds1-magn"; |
| reg = <0x1c>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mag>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <2 IRQ_TYPE_EDGE_RISING>; |
| }; |
| |
| imu@6a { |
| compatible = "st,lsm9ds1-imu"; |
| reg = <0x6a>; |
| st,drdy-int-pin = <1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_imu>; |
| interrupt-parent = <&gpio7>; |
| interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| ltc3676: pmic@3c { |
| compatible = "lltc,ltc3676"; |
| reg = <0x3c>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pmic>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <8 IRQ_TYPE_EDGE_FALLING>; |
| |
| regulators { |
| /* VDD_SOC (1+R1/R2 = 1.635) */ |
| reg_vdd_soc: sw1 { |
| regulator-name = "vddsoc"; |
| regulator-min-microvolt = <674400>; |
| regulator-max-microvolt = <1308000>; |
| lltc,fb-voltage-divider = <127000 200000>; |
| regulator-ramp-delay = <7000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| /* VDD_DDR (1+R1/R2 = 2.105) */ |
| reg_vdd_ddr: sw2 { |
| regulator-name = "vddddr"; |
| regulator-min-microvolt = <868310>; |
| regulator-max-microvolt = <1684000>; |
| lltc,fb-voltage-divider = <221000 200000>; |
| regulator-ramp-delay = <7000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| /* VDD_ARM (1+R1/R2 = 1.635) */ |
| reg_vdd_arm: sw3 { |
| regulator-name = "vddarm"; |
| regulator-min-microvolt = <674400>; |
| regulator-max-microvolt = <1308000>; |
| lltc,fb-voltage-divider = <127000 200000>; |
| regulator-ramp-delay = <7000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| /* VDD_3P3 (1+R1/R2 = 1.281) */ |
| reg_3p3v: sw4 { |
| regulator-name = "vdd3p3"; |
| regulator-min-microvolt = <1880000>; |
| regulator-max-microvolt = <3647000>; |
| lltc,fb-voltage-divider = <200000 56200>; |
| regulator-ramp-delay = <7000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| /* VDD_1P8a (1+R1/R2 = 2.505): Analog Video Decoder */ |
| reg_1p8a: ldo2 { |
| regulator-name = "vdd1p8a"; |
| regulator-min-microvolt = <1816125>; |
| regulator-max-microvolt = <1816125>; |
| lltc,fb-voltage-divider = <301000 200000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| /* VDD_1P8b: microSD VDD_1P8 */ |
| reg_1p8b: ldo3 { |
| regulator-name = "vdd1p8b"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| }; |
| |
| /* VDD_HIGH (1+R1/R2 = 4.17) */ |
| reg_3p0v: ldo4 { |
| regulator-name = "vdd3p0"; |
| regulator-min-microvolt = <3023250>; |
| regulator-max-microvolt = <3023250>; |
| lltc,fb-voltage-divider = <634000 200000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| status = "okay"; |
| |
| adv7180: camera@20 { |
| compatible = "adi,adv7180"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_adv7180>; |
| reg = <0x20>; |
| powerdown-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; |
| interrupt-parent = <&gpio5>; |
| interrupts = <23 IRQ_TYPE_LEVEL_LOW>; |
| |
| port { |
| adv7180_to_ipu1_csi0_mux: endpoint { |
| remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; |
| bus-width = <8>; |
| }; |
| }; |
| }; |
| }; |
| |
| &ipu1_csi0_from_ipu1_csi0_mux { |
| bus-width = <8>; |
| }; |
| |
| &ipu1_csi0_mux_from_parallel_sensor { |
| remote-endpoint = <&adv7180_to_ipu1_csi0_mux>; |
| bus-width = <8>; |
| }; |
| |
| &ipu1_csi0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ipu1_csi0>; |
| }; |
| |
| &pcie { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pcie>; |
| reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| |
| &pwm2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */ |
| status = "disabled"; |
| }; |
| |
| &pwm3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */ |
| status = "disabled"; |
| }; |
| |
| &pwm4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */ |
| status = "disabled"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| status = "okay"; |
| }; |
| |
| &uart4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart4>; |
| status = "okay"; |
| }; |
| |
| &uart5 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart5>; |
| status = "okay"; |
| }; |
| |
| &usbh1 { |
| status = "okay"; |
| }; |
| |
| &usbotg { |
| vbus-supply = <®_usb_otg_vbus>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotg>; |
| disable-over-current; |
| status = "okay"; |
| }; |
| |
| &usdhc3 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc3>; |
| pinctrl-1 = <&pinctrl_usdhc3_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc3_200mhz>; |
| cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog>; |
| fsl,ext-reset-output; |
| }; |
| |
| &iomuxc { |
| pinctrl_adv7180: adv7180grp { |
| fsl,pins = < |
| MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x0001b0b0 |
| MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x4001b0b0 |
| >; |
| }; |
| |
| pinctrl_gpmi_nand: gpminandgrp { |
| fsl,pins = < |
| MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 |
| MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 |
| MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 |
| MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 |
| MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 |
| MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 |
| MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 |
| MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 |
| MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 |
| MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 |
| MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 |
| MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 |
| MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 |
| MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 |
| MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 |
| >; |
| }; |
| |
| pinctrl_hdmi: hdmigrp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 |
| MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 |
| MX6QDL_PAD_GPIO_4__GPIO1_IO04 0xb0b1 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 |
| MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 |
| MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_imu: imugrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_ipu1_csi0: ipu1csi0grp { |
| fsl,pins = < |
| MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0 |
| MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0 |
| MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0 |
| MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0 |
| MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0 |
| MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0 |
| MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0 |
| MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0 |
| MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x1b0b0 |
| MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x1b0b0 |
| MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_gpio_leds: gpioledsgrp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0 |
| MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_mag: maggrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_pcie: pciegrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 |
| MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x4001b0b0 /* PCIESKT_WDIS# */ |
| >; |
| }; |
| |
| pinctrl_pmic: pmicgrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x0001b0b0 /* PMIC_IRQ# */ |
| >; |
| }; |
| |
| pinctrl_pps: ppsgrp { |
| fsl,pins = < |
| MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_pwm2: pwm2grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_pwm3: pwm3grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_pwm4: pwm4grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart3: uart3grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart4: uart4grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart5: uart5grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_usbotg: usbotggrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 |
| MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 /* OTG_PWR_EN */ |
| MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x17059 |
| >; |
| }; |
| |
| pinctrl_usdhc3: usdhc3grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 |
| MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 |
| MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 |
| MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 |
| MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 |
| MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 |
| MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x17059 /* CD */ |
| MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x17059 |
| >; |
| }; |
| |
| pinctrl_usdhc3_100mhz: usdhc3grp100mhz { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9 |
| MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9 |
| MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9 |
| MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9 |
| MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9 |
| MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9 |
| MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170b9 /* CD */ |
| MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170b9 |
| >; |
| }; |
| |
| pinctrl_usdhc3_200mhz: usdhc3grp200mhz { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9 |
| MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9 |
| MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 |
| MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 |
| MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 |
| MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 |
| MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170f9 /* CD */ |
| MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170f9 |
| >; |
| }; |
| |
| pinctrl_wdog: wdoggrp { |
| fsl,pins = < |
| MX6QDL_PAD_DISP0_DAT8__WDOG1_B 0x1b0b0 |
| >; |
| }; |
| }; |
