| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (C) 2015 |
| * Nikolaus Schaller <hns@goldelico.com> |
| * |
| * Common device tree include for OpenPandora devices. |
| */ |
| |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| cpus { |
| cpu@0 { |
| cpu0-supply = <&vcc>; |
| }; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x80000000 0x20000000>; /* 512 MB */ |
| }; |
| |
| aliases { |
| display0 = &lcd; |
| }; |
| |
| /* fixed 26MHz oscillator */ |
| hfclk_26m: oscillator { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <26000000>; |
| }; |
| |
| tv: connector { |
| compatible = "connector-analog-tv"; |
| label = "tv"; |
| |
| port { |
| tv_connector_in: endpoint { |
| remote-endpoint = <&venc_out>; |
| }; |
| }; |
| }; |
| |
| gpio-leds { |
| |
| compatible = "gpio-leds"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&led_pins>; |
| |
| led1 { |
| label = "pandora::sd1"; |
| gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>; /* GPIO_128 */ |
| linux,default-trigger = "mmc0"; |
| default-state = "off"; |
| }; |
| |
| led2 { |
| label = "pandora::sd2"; |
| gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; /* GPIO_129 */ |
| linux,default-trigger = "mmc1"; |
| default-state = "off"; |
| }; |
| |
| led3 { |
| label = "pandora::bluetooth"; |
| gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>; /* GPIO_158 */ |
| linux,default-trigger = "heartbeat"; |
| default-state = "off"; |
| }; |
| |
| led4 { |
| label = "pandora::wifi"; |
| gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>; /* GPIO_159 */ |
| linux,default-trigger = "mmc2"; |
| default-state = "off"; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&button_pins>; |
| |
| up-button { |
| label = "up"; |
| linux,code = <KEY_UP>; |
| gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* GPIO_110 */ |
| wakeup-source; |
| }; |
| |
| down-button { |
| label = "down"; |
| linux,code = <KEY_DOWN>; |
| gpios = <&gpio4 7 GPIO_ACTIVE_LOW>; /* GPIO_103 */ |
| wakeup-source; |
| }; |
| |
| left-button { |
| label = "left"; |
| linux,code = <KEY_LEFT>; |
| gpios = <&gpio4 0 GPIO_ACTIVE_LOW>; /* GPIO_96 */ |
| wakeup-source; |
| }; |
| |
| right-button { |
| label = "right"; |
| linux,code = <KEY_RIGHT>; |
| gpios = <&gpio4 2 GPIO_ACTIVE_LOW>; /* GPIO_98 */ |
| wakeup-source; |
| }; |
| |
| pageup-button { |
| label = "game 1"; |
| linux,code = <KEY_PAGEUP>; |
| gpios = <&gpio4 13 GPIO_ACTIVE_LOW>; /* GPIO_109 */ |
| wakeup-source; |
| }; |
| |
| pagedown-button { |
| label = "game 3"; |
| linux,code = <KEY_PAGEDOWN>; |
| gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; /* GPIO_106 */ |
| wakeup-source; |
| }; |
| |
| home-button { |
| label = "game 4"; |
| linux,code = <KEY_HOME>; |
| gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* GPIO_101 */ |
| wakeup-source; |
| }; |
| |
| end-button { |
| label = "game 2"; |
| linux,code = <KEY_END>; |
| gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* GPIO_111 */ |
| wakeup-source; |
| }; |
| |
| right-shift { |
| label = "l"; |
| linux,code = <KEY_RIGHTSHIFT>; |
| gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* GPIO_102 */ |
| wakeup-source; |
| }; |
| |
| kp-plus { |
| label = "l2"; |
| linux,code = <KEY_KPPLUS>; |
| gpios = <&gpio4 1 GPIO_ACTIVE_LOW>; /* GPIO_97 */ |
| wakeup-source; |
| }; |
| |
| right-ctrl { |
| label = "r"; |
| linux,code = <KEY_RIGHTCTRL>; |
| gpios = <&gpio4 9 GPIO_ACTIVE_LOW>; /* GPIO_105 */ |
| wakeup-source; |
| }; |
| |
| kp-minus { |
| label = "r2"; |
| linux,code = <KEY_KPMINUS>; |
| gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; /* GPIO_107 */ |
| wakeup-source; |
| }; |
| |
| left-ctrl { |
| label = "ctrl"; |
| linux,code = <KEY_LEFTCTRL>; |
| gpios = <&gpio4 8 GPIO_ACTIVE_LOW>; /* GPIO_104 */ |
| wakeup-source; |
| }; |
| |
| menu { |
| label = "menu"; |
| linux,code = <KEY_MENU>; |
| gpios = <&gpio4 3 GPIO_ACTIVE_LOW>; /* GPIO_99 */ |
| wakeup-source; |
| }; |
| |
| hold { |
| label = "hold"; |
| linux,code = <KEY_COFFEE>; |
| gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* GPIO_176 */ |
| wakeup-source; |
| }; |
| |
| left-alt { |
| label = "alt"; |
| linux,code = <KEY_LEFTALT>; |
| gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; /* GPIO_100 */ |
| wakeup-source; |
| }; |
| |
| lid { |
| label = "lid"; |
| linux,code = <0x00>; /* SW_LID lid shut */ |
| linux,input-type = <0x05>; /* EV_SW */ |
| gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; /* GPIO_108 */ |
| }; |
| }; |
| |
| /* HS USB Host PHY on PORT 2 */ |
| hsusb2_phy: hsusb2_phy { |
| compatible = "usb-nop-xceiv"; |
| reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; /* GPIO_16 */ |
| vcc-supply = <&vaux2>; |
| #phy-cells = <0>; |
| }; |
| |
| /* HS USB Host VBUS supply |
| * disabling this regulator causes current leakage, and LCD flicker |
| * on earlier (CC) board revisions, so keep it always on */ |
| usb_host_5v: fixed-regulator-usb_host_5v { |
| compatible = "regulator-fixed"; |
| regulator-name = "usb_host_5v"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| enable-active-high; |
| gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* GPIO_164 */ |
| }; |
| |
| /* wl1251 wifi+bt module */ |
| wlan_en: fixed-regulator-wg7210_en { |
| compatible = "regulator-fixed"; |
| regulator-name = "vwlan"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| startup-delay-us = <50000>; |
| enable-active-high; |
| gpio = <&gpio1 23 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| /* wg7210 (wifi+bt module) 32k clock buffer */ |
| wg7210_32k: fixed-regulator-wg7210_32k { |
| compatible = "regulator-fixed"; |
| regulator-name = "wg7210_32k"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| enable-active-high; |
| gpio = <&twl_gpio 13 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| &omap3_pmx_core { |
| |
| mmc1_pins: pinmux_mmc1_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ |
| OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ |
| OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ |
| OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ |
| OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ |
| OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ |
| >; |
| }; |
| |
| mmc2_pins: pinmux_mmc2_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ |
| OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ |
| OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ |
| OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ |
| OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ |
| OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ |
| OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dirdat0 */ |
| OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dirdat1 */ |
| OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dircmd */ |
| OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */ |
| >; |
| }; |
| |
| dss_dpi_pins: pinmux_dss_dpi_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ |
| OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ |
| OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ |
| OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ |
| OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ |
| OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ |
| OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ |
| OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ |
| OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ |
| OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ |
| OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ |
| OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ |
| OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ |
| OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ |
| OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ |
| OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ |
| OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ |
| OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ |
| OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ |
| OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ |
| OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ |
| OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ |
| OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ |
| OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ |
| OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ |
| OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ |
| OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ |
| OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ |
| OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* GPIO_157 = lcd reset */ |
| >; |
| }; |
| |
| uart3_pins: pinmux_uart3_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ |
| OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ |
| >; |
| }; |
| |
| led_pins: pinmux_leds_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2154, PIN_OUTPUT | MUX_MODE4) /* GPIO_128 */ |
| OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4) /* GPIO_129 */ |
| OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE4) /* GPIO_158 */ |
| OMAP3_CORE1_IOPAD(0x2192, PIN_OUTPUT | MUX_MODE4) /* GPIO_159 */ |
| >; |
| }; |
| |
| button_pins: pinmux_button_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE4) /* GPIO_96 */ |
| OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE4) /* GPIO_97 */ |
| OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE4) /* GPIO_98 */ |
| OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE4) /* GPIO_99 */ |
| OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE4) /* GPIO_100 */ |
| OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT | MUX_MODE4) /* GPIO_101 */ |
| OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE4) /* GPIO_102 */ |
| OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE4) /* GPIO_103 */ |
| OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE4) /* GPIO_104 */ |
| OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE4) /* GPIO_105 */ |
| OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE4) /* GPIO_106 */ |
| OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT | MUX_MODE4) /* GPIO_107 */ |
| OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT | MUX_MODE4) /* GPIO_108 */ |
| OMAP3_CORE1_IOPAD(0x212a, PIN_INPUT | MUX_MODE4) /* GPIO_109 */ |
| OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT | MUX_MODE4) /* GPIO_110 */ |
| OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT | MUX_MODE4) /* GPIO_111 */ |
| OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4) /* GPIO_176 */ |
| >; |
| }; |
| |
| penirq_pins: pinmux_penirq_pins { |
| pinctrl-single,pins = < |
| /* here we could enable to wakeup the cpu from suspend by a pen touch */ |
| OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE4) /* GPIO_94 */ |
| >; |
| }; |
| |
| }; |
| |
| &omap3_pmx_core2 { |
| /* define in CPU specific file that includes this one |
| * use either OMAP3430_CORE2_IOPAD() or OMAP3630_CORE2_IOPAD() |
| */ |
| }; |
| |
| &i2c1 { |
| clock-frequency = <2600000>; |
| |
| twl: twl@48 { |
| reg = <0x48>; |
| interrupts = <7>; /* SYS_NIRQ cascaded to intc */ |
| interrupt-parent = <&intc>; |
| |
| clocks = <&hfclk_26m>; |
| clock-names = "fck"; |
| |
| twl_power: power { |
| compatible = "ti,twl4030-power-reset"; |
| ti,use_poweroff; |
| }; |
| |
| twl_audio: audio { |
| compatible = "ti,twl4030-audio"; |
| |
| codec { |
| ti,ramp_delay_value = <3>; |
| }; |
| }; |
| }; |
| }; |
| |
| #include "twl4030.dtsi" |
| #include "twl4030_omap3.dtsi" |
| |
| &twl_keypad { |
| keypad,num-rows = <8>; |
| keypad,num-columns = <6>; |
| linux,keymap = < |
| MATRIX_KEY(0, 0, KEY_9) |
| MATRIX_KEY(0, 1, KEY_8) |
| MATRIX_KEY(0, 2, KEY_I) |
| MATRIX_KEY(0, 3, KEY_J) |
| MATRIX_KEY(0, 4, KEY_N) |
| MATRIX_KEY(0, 5, KEY_M) |
| MATRIX_KEY(1, 0, KEY_0) |
| MATRIX_KEY(1, 1, KEY_7) |
| MATRIX_KEY(1, 2, KEY_U) |
| MATRIX_KEY(1, 3, KEY_H) |
| MATRIX_KEY(1, 4, KEY_B) |
| MATRIX_KEY(1, 5, KEY_SPACE) |
| MATRIX_KEY(2, 0, KEY_BACKSPACE) |
| MATRIX_KEY(2, 1, KEY_6) |
| MATRIX_KEY(2, 2, KEY_Y) |
| MATRIX_KEY(2, 3, KEY_G) |
| MATRIX_KEY(2, 4, KEY_V) |
| MATRIX_KEY(2, 5, KEY_FN) |
| MATRIX_KEY(3, 0, KEY_O) |
| MATRIX_KEY(3, 1, KEY_5) |
| MATRIX_KEY(3, 2, KEY_T) |
| MATRIX_KEY(3, 3, KEY_F) |
| MATRIX_KEY(3, 4, KEY_C) |
| MATRIX_KEY(4, 0, KEY_P) |
| MATRIX_KEY(4, 1, KEY_4) |
| MATRIX_KEY(4, 2, KEY_R) |
| MATRIX_KEY(4, 3, KEY_D) |
| MATRIX_KEY(4, 4, KEY_X) |
| MATRIX_KEY(5, 0, KEY_K) |
| MATRIX_KEY(5, 1, KEY_3) |
| MATRIX_KEY(5, 2, KEY_E) |
| MATRIX_KEY(5, 3, KEY_S) |
| MATRIX_KEY(5, 4, KEY_Z) |
| MATRIX_KEY(6, 0, KEY_L) |
| MATRIX_KEY(6, 1, KEY_2) |
| MATRIX_KEY(6, 2, KEY_W) |
| MATRIX_KEY(6, 3, KEY_A) |
| MATRIX_KEY(6, 4, KEY_RIGHTBRACE) |
| MATRIX_KEY(7, 0, KEY_ENTER) |
| MATRIX_KEY(7, 1, KEY_1) |
| MATRIX_KEY(7, 2, KEY_Q) |
| MATRIX_KEY(7, 3, KEY_LEFTSHIFT) |
| MATRIX_KEY(7, 4, KEY_LEFTBRACE ) |
| >; |
| }; |
| |
| /* backup battery charger */ |
| &charger { |
| ti,bb-uvolt = <3200000>; |
| ti,bb-uamp = <150>; |
| }; |
| |
| /* MMC2 */ |
| &vmmc2 { |
| regulator-min-microvolt = <1850000>; |
| regulator-max-microvolt = <3150000>; |
| }; |
| |
| /* LCD */ |
| &vaux1 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| /* USB Host PHY */ |
| &vaux2 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| /* available on expansion connector */ |
| &vaux3 { |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| |
| /* ADS7846 and nubs */ |
| &vaux4 { |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| |
| /* power audio DAC and LID sensor */ |
| &vsim { |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-always-on; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <100000>; |
| /* no clients so we should disable clock */ |
| }; |
| |
| &i2c3 { |
| clock-frequency = <100000>; |
| |
| bq27500@55 { |
| compatible = "ti,bq27500"; |
| reg = <0x55>; |
| }; |
| |
| }; |
| |
| &usb_otg_hs { |
| interface-type = <0>; |
| usb-phy = <&usb2_phy>; |
| phys = <&usb2_phy>; |
| phy-names = "usb2-phy"; |
| mode = <3>; |
| power = <50>; |
| }; |
| |
| /* |
| * Many pandora boards have been produced with defective write-protect switches |
| * on either slot, so it was decided not to use this feature. If you know |
| * your board has good switches, feel free to uncomment wp-gpios below. |
| */ |
| &mmc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc1_pins>; |
| vmmc-supply = <&vmmc1>; |
| bus-width = <4>; |
| cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>; |
| /*wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>;*/ /* GPIO_126 */ |
| }; |
| |
| &mmc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc2_pins>; |
| vmmc-supply = <&vmmc2>; |
| bus-width = <4>; |
| cd-gpios = <&twl_gpio 1 GPIO_ACTIVE_LOW>; |
| /*wp-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;*/ /* GPIO_127 */ |
| }; |
| |
| &mmc3 { |
| vmmc-supply = <&wlan_en>; |
| |
| bus-width = <4>; |
| non-removable; |
| ti,non-removable; |
| cap-power-off-card; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc3_pins>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| wlan: wifi@1 { |
| compatible = "ti,wl1251"; |
| |
| reg = <1>; |
| |
| interrupt-parent = <&gpio1>; |
| interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_21 */ |
| |
| ti,wl1251-has-eeprom; |
| }; |
| }; |
| |
| /* bluetooth*/ |
| &uart1 { |
| }; |
| |
| /* spare (expansion connector) */ |
| &uart2 { |
| }; |
| |
| /* console (expansion connector) */ |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart3_pins>; |
| interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>; |
| }; |
| |
| &usbhshost { |
| port2-mode = "ehci-phy"; |
| }; |
| |
| &usbhsehci { |
| phys = <0 &hsusb2_phy>; |
| }; |
| |
| &gpmc { |
| ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ |
| |
| nand@0,0 { |
| compatible = "ti,omap2-nand"; |
| reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ |
| interrupt-parent = <&gpmc>; |
| interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ |
| <1 IRQ_TYPE_NONE>; /* termcount */ |
| nand-bus-width = <16>; |
| ti,nand-ecc-opt = "sw"; |
| |
| gpmc,sync-clk-ps = <0>; |
| gpmc,cs-on-ns = <0>; |
| gpmc,cs-rd-off-ns = <44>; |
| gpmc,cs-wr-off-ns = <44>; |
| gpmc,adv-on-ns = <6>; |
| gpmc,adv-rd-off-ns = <34>; |
| gpmc,adv-wr-off-ns = <44>; |
| gpmc,we-off-ns = <40>; |
| gpmc,oe-off-ns = <54>; |
| gpmc,access-ns = <64>; |
| gpmc,rd-cycle-ns = <82>; |
| gpmc,wr-cycle-ns = <82>; |
| gpmc,wr-access-ns = <40>; |
| gpmc,wr-data-mux-bus-ns = <0>; |
| gpmc,device-width = <2>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| /* u-boot uses mtdparts=nand:512k(xloader),1920k(uboot),128k(uboot-env),10m(boot),-(rootfs) */ |
| |
| x-loader@0 { |
| label = "xloader"; |
| reg = <0 0x80000>; |
| }; |
| |
| bootloaders@80000 { |
| label = "uboot"; |
| reg = <0x80000 0x1e0000>; |
| }; |
| |
| bootloaders_env@260000 { |
| label = "uboot-env"; |
| reg = <0x260000 0x20000>; |
| }; |
| |
| kernel@280000 { |
| label = "boot"; |
| reg = <0x280000 0xa00000>; |
| }; |
| |
| filesystem@c80000 { |
| label = "rootfs"; |
| reg = <0xc80000 0>; /* 0 = MTDPART_SIZ_FULL */ |
| }; |
| }; |
| }; |
| |
| &mcspi1 { |
| tsc2046@0 { |
| reg = <0>; /* CS0 */ |
| compatible = "ti,tsc2046"; |
| spi-max-frequency = <1000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&penirq_pins>; |
| interrupt-parent = <&gpio3>; |
| interrupts = <30 IRQ_TYPE_NONE>; /* GPIO_94 */ |
| pendown-gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; |
| vcc-supply = <&vaux4>; |
| |
| ti,x-min = /bits/ 16 <0>; |
| ti,x-max = /bits/ 16 <8000>; |
| ti,y-min = /bits/ 16 <0>; |
| ti,y-max = /bits/ 16 <4800>; |
| ti,x-plate-ohms = /bits/ 16 <40>; |
| ti,pressure-max = /bits/ 16 <255>; |
| |
| wakeup-source; |
| }; |
| |
| lcd: lcd@1 { |
| reg = <1>; /* CS1 */ |
| compatible = "tpo,td043mtea1"; |
| spi-max-frequency = <100000>; |
| spi-cpol; |
| spi-cpha; |
| |
| label = "lcd"; |
| reset-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>; /* GPIO_157 */ |
| vcc-supply = <&vaux1>; |
| |
| port { |
| lcd_in: endpoint { |
| remote-endpoint = <&dpi_out>; |
| }; |
| }; |
| }; |
| |
| |
| }; |
| |
| /* n/a - used as GPIOs */ |
| &mcbsp1 { |
| }; |
| |
| /* audio DAC */ |
| &mcbsp2 { |
| }; |
| |
| /* bluetooth */ |
| &mcbsp3 { |
| }; |
| |
| /* to twl4030*/ |
| &mcbsp4 { |
| }; |
| |
| &venc { |
| status = "okay"; |
| |
| vdda-supply = <&vdac>; |
| |
| port { |
| venc_out: endpoint { |
| remote-endpoint = <&tv_connector_in>; |
| ti,channels = <2>; |
| }; |
| }; |
| }; |
| |
| &dss { |
| pinctrl-names = "default"; |
| pinctrl-0 = < &dss_dpi_pins >; |
| |
| status = "okay"; |
| vdds_dsi-supply = <&vpll2>; |
| |
| port { |
| dpi_out: endpoint { |
| remote-endpoint = <&lcd_in>; |
| data-lines = <24>; |
| }; |
| }; |
| }; |
