| // SPDX-License-Identifier: GPL-2.0 |
| /dts-v1/; |
| |
| #include <dt-bindings/input/input.h> |
| #include "tegra30-colibri.dtsi" |
| |
| / { |
| model = "Toradex Colibri T30 on Colibri Evaluation Board"; |
| compatible = "toradex,colibri_t30-eval-v3", "toradex,colibri_t30", |
| "nvidia,tegra30"; |
| |
| aliases { |
| rtc0 = "/i2c@7000c000/rtc@68"; |
| rtc1 = "/i2c@7000d000/pmic@2d"; |
| rtc2 = "/rtc@7000e000"; |
| serial0 = &uarta; |
| serial1 = &uartb; |
| serial2 = &uartd; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| host1x@50000000 { |
| dc@54200000 { |
| rgb { |
| status = "okay"; |
| nvidia,panel = <&panel>; |
| }; |
| }; |
| |
| hdmi@54280000 { |
| status = "okay"; |
| hdmi-supply = <®_5v0>; |
| }; |
| }; |
| |
| /* Colibri UART-A */ |
| serial@70006000 { |
| status = "okay"; |
| }; |
| |
| /* Colibri UART-C */ |
| serial@70006040 { |
| status = "okay"; |
| }; |
| |
| /* Colibri UART-B */ |
| serial@70006300 { |
| status = "okay"; |
| }; |
| |
| pwm@7000a000 { |
| status = "okay"; |
| }; |
| |
| /* |
| * GEN1_I2C: I2C_SDA/SCL on SODIMM pin 194/196 (e.g. RTC on carrier |
| * board) |
| */ |
| i2c@7000c000 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| /* M41T0M6 real time clock on carrier board */ |
| rtc@68 { |
| compatible = "st,m41t0"; |
| reg = <0x68>; |
| }; |
| }; |
| |
| /* GEN2_I2C: unused */ |
| |
| /* CAM_I2C (I2C3): unused */ |
| |
| /* DDC_CLOCK/DATA on X3 pin 15/16 (e.g. display EDID) */ |
| i2c@7000c700 { |
| status = "okay"; |
| }; |
| |
| /* SPI1: Colibri SSP */ |
| spi@7000d400 { |
| status = "okay"; |
| spi-max-frequency = <25000000>; |
| |
| can@0 { |
| compatible = "microchip,mcp2515"; |
| reg = <0>; |
| clocks = <&clk16m>; |
| interrupt-parent = <&gpio>; |
| /* CAN_INT */ |
| interrupts = <TEGRA_GPIO(S, 0) IRQ_TYPE_EDGE_FALLING>; |
| spi-max-frequency = <10000000>; |
| vdd-supply = <®_3v3>; |
| xceiver-supply = <®_5v0>; |
| }; |
| }; |
| |
| /* SD/MMC */ |
| mmc@78000200 { |
| status = "okay"; |
| bus-width = <4>; |
| cd-gpios = <&gpio TEGRA_GPIO(C, 7) GPIO_ACTIVE_LOW>; /* MMCD */ |
| no-1-8-v; |
| }; |
| |
| /* EHCI instance 0: USB1_DP/N -> USBC_P/N */ |
| usb@7d000000 { |
| status = "okay"; |
| dr_mode = "otg"; |
| }; |
| |
| usb-phy@7d000000 { |
| status = "okay"; |
| vbus-supply = <®_usbc_vbus>; |
| }; |
| |
| /* EHCI instance 2: USB3_DP/N -> USBH_P/N */ |
| usb@7d008000 { |
| status = "okay"; |
| }; |
| |
| usb-phy@7d008000 { |
| status = "okay"; |
| vbus-supply = <®_usbh_vbus>; |
| }; |
| |
| backlight: backlight { |
| compatible = "pwm-backlight"; |
| brightness-levels = <255 128 64 32 16 8 4 0>; |
| default-brightness-level = <6>; |
| /* BL_ON */ |
| enable-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>; |
| power-supply = <®_3v3>; |
| pwms = <&pwm 0 5000000>; /* PWM<A> */ |
| }; |
| |
| clk16m: osc3 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <16000000>; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| wakeup { |
| label = "SODIMM pin 45 wakeup"; |
| gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_HIGH>; |
| linux,code = <KEY_WAKEUP>; |
| debounce-interval = <10>; |
| wakeup-source; |
| }; |
| }; |
| |
| panel: panel { |
| /* |
| * edt,et057090dhu: EDT 5.7" LCD TFT |
| * edt,et070080dh6: EDT 7.0" LCD TFT |
| */ |
| compatible = "edt,et057090dhu"; |
| backlight = <&backlight>; |
| power-supply = <®_3v3>; |
| }; |
| |
| reg_3v3: regulator-3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "3.3V_SW"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| reg_5v0: regulator-5v0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "5V_SW"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| |
| reg_usbc_vbus: regulator-usbc-vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "VCC_USB5"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <®_5v0>; |
| }; |
| |
| /* USBH_PEN resp. USB_P_EN */ |
| reg_usbh_vbus: regulator-usbh-vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "VCC_USB[1-4]"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>; |
| vin-supply = <®_5v0>; |
| }; |
| }; |