| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * TI SN65DSI83,84,85 driver |
| * |
| * Currently supported: |
| * - SN65DSI83 |
| * = 1x Single-link DSI ~ 1x Single-link LVDS |
| * - Supported |
| * - Single-link LVDS mode tested |
| * - SN65DSI84 |
| * = 1x Single-link DSI ~ 2x Single-link or 1x Dual-link LVDS |
| * - Supported |
| * - Dual-link LVDS mode tested |
| * - 2x Single-link LVDS mode unsupported |
| * (should be easy to add by someone who has the HW) |
| * - SN65DSI85 |
| * = 2x Single-link or 1x Dual-link DSI ~ 2x Single-link or 1x Dual-link LVDS |
| * - Unsupported |
| * (should be easy to add by someone who has the HW) |
| * |
| * Copyright (C) 2021 Marek Vasut <marex@denx.de> |
| * |
| * Based on previous work of: |
| * Valentin Raevsky <valentin@compulab.co.il> |
| * Philippe Schenker <philippe.schenker@toradex.com> |
| */ |
| |
| #include <linux/bits.h> |
| #include <linux/clk.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/i2c.h> |
| #include <linux/module.h> |
| #include <linux/of_device.h> |
| #include <linux/of_graph.h> |
| #include <linux/regmap.h> |
| |
| #include <drm/drm_atomic_helper.h> |
| #include <drm/drm_bridge.h> |
| #include <drm/drm_mipi_dsi.h> |
| #include <drm/drm_of.h> |
| #include <drm/drm_panel.h> |
| #include <drm/drm_print.h> |
| #include <drm/drm_probe_helper.h> |
| |
| /* ID registers */ |
| #define REG_ID(n) (0x00 + (n)) |
| /* Reset and clock registers */ |
| #define REG_RC_RESET 0x09 |
| #define REG_RC_RESET_SOFT_RESET BIT(0) |
| #define REG_RC_LVDS_PLL 0x0a |
| #define REG_RC_LVDS_PLL_PLL_EN_STAT BIT(7) |
| #define REG_RC_LVDS_PLL_LVDS_CLK_RANGE(n) (((n) & 0x7) << 1) |
| #define REG_RC_LVDS_PLL_HS_CLK_SRC_DPHY BIT(0) |
| #define REG_RC_DSI_CLK 0x0b |
| #define REG_RC_DSI_CLK_DSI_CLK_DIVIDER(n) (((n) & 0x1f) << 3) |
| #define REG_RC_DSI_CLK_REFCLK_MULTIPLIER(n) ((n) & 0x3) |
| #define REG_RC_PLL_EN 0x0d |
| #define REG_RC_PLL_EN_PLL_EN BIT(0) |
| /* DSI registers */ |
| #define REG_DSI_LANE 0x10 |
| #define REG_DSI_LANE_LEFT_RIGHT_PIXELS BIT(7) /* DSI85-only */ |
| #define REG_DSI_LANE_DSI_CHANNEL_MODE_DUAL 0 /* DSI85-only */ |
| #define REG_DSI_LANE_DSI_CHANNEL_MODE_2SINGLE BIT(6) /* DSI85-only */ |
| #define REG_DSI_LANE_DSI_CHANNEL_MODE_SINGLE BIT(5) |
| #define REG_DSI_LANE_CHA_DSI_LANES(n) (((n) & 0x3) << 3) |
| #define REG_DSI_LANE_CHB_DSI_LANES(n) (((n) & 0x3) << 1) |
| #define REG_DSI_LANE_SOT_ERR_TOL_DIS BIT(0) |
| #define REG_DSI_EQ 0x11 |
| #define REG_DSI_EQ_CHA_DSI_DATA_EQ(n) (((n) & 0x3) << 6) |
| #define REG_DSI_EQ_CHA_DSI_CLK_EQ(n) (((n) & 0x3) << 2) |
| #define REG_DSI_CLK 0x12 |
| #define REG_DSI_CLK_CHA_DSI_CLK_RANGE(n) ((n) & 0xff) |
| /* LVDS registers */ |
| #define REG_LVDS_FMT 0x18 |
| #define REG_LVDS_FMT_DE_NEG_POLARITY BIT(7) |
| #define REG_LVDS_FMT_HS_NEG_POLARITY BIT(6) |
| #define REG_LVDS_FMT_VS_NEG_POLARITY BIT(5) |
| #define REG_LVDS_FMT_LVDS_LINK_CFG BIT(4) /* 0:AB 1:A-only */ |
| #define REG_LVDS_FMT_CHA_24BPP_MODE BIT(3) |
| #define REG_LVDS_FMT_CHB_24BPP_MODE BIT(2) |
| #define REG_LVDS_FMT_CHA_24BPP_FORMAT1 BIT(1) |
| #define REG_LVDS_FMT_CHB_24BPP_FORMAT1 BIT(0) |
| #define REG_LVDS_VCOM 0x19 |
| #define REG_LVDS_VCOM_CHA_LVDS_VOCM BIT(6) |
| #define REG_LVDS_VCOM_CHB_LVDS_VOCM BIT(4) |
| #define REG_LVDS_VCOM_CHA_LVDS_VOD_SWING(n) (((n) & 0x3) << 2) |
| #define REG_LVDS_VCOM_CHB_LVDS_VOD_SWING(n) ((n) & 0x3) |
| #define REG_LVDS_LANE 0x1a |
| #define REG_LVDS_LANE_EVEN_ODD_SWAP BIT(6) |
| #define REG_LVDS_LANE_CHA_REVERSE_LVDS BIT(5) |
| #define REG_LVDS_LANE_CHB_REVERSE_LVDS BIT(4) |
| #define REG_LVDS_LANE_CHA_LVDS_TERM BIT(1) |
| #define REG_LVDS_LANE_CHB_LVDS_TERM BIT(0) |
| #define REG_LVDS_CM 0x1b |
| #define REG_LVDS_CM_CHA_LVDS_CM_ADJUST(n) (((n) & 0x3) << 4) |
| #define REG_LVDS_CM_CHB_LVDS_CM_ADJUST(n) ((n) & 0x3) |
| /* Video registers */ |
| #define REG_VID_CHA_ACTIVE_LINE_LENGTH_LOW 0x20 |
| #define REG_VID_CHA_ACTIVE_LINE_LENGTH_HIGH 0x21 |
| #define REG_VID_CHA_VERTICAL_DISPLAY_SIZE_LOW 0x24 |
| #define REG_VID_CHA_VERTICAL_DISPLAY_SIZE_HIGH 0x25 |
| #define REG_VID_CHA_SYNC_DELAY_LOW 0x28 |
| #define REG_VID_CHA_SYNC_DELAY_HIGH 0x29 |
| #define REG_VID_CHA_HSYNC_PULSE_WIDTH_LOW 0x2c |
| #define REG_VID_CHA_HSYNC_PULSE_WIDTH_HIGH 0x2d |
| #define REG_VID_CHA_VSYNC_PULSE_WIDTH_LOW 0x30 |
| #define REG_VID_CHA_VSYNC_PULSE_WIDTH_HIGH 0x31 |
| #define REG_VID_CHA_HORIZONTAL_BACK_PORCH 0x34 |
| #define REG_VID_CHA_VERTICAL_BACK_PORCH 0x36 |
| #define REG_VID_CHA_HORIZONTAL_FRONT_PORCH 0x38 |
| #define REG_VID_CHA_VERTICAL_FRONT_PORCH 0x3a |
| #define REG_VID_CHA_TEST_PATTERN 0x3c |
| /* IRQ registers */ |
| #define REG_IRQ_GLOBAL 0xe0 |
| #define REG_IRQ_GLOBAL_IRQ_EN BIT(0) |
| #define REG_IRQ_EN 0xe1 |
| #define REG_IRQ_EN_CHA_SYNCH_ERR_EN BIT(7) |
| #define REG_IRQ_EN_CHA_CRC_ERR_EN BIT(6) |
| #define REG_IRQ_EN_CHA_UNC_ECC_ERR_EN BIT(5) |
| #define REG_IRQ_EN_CHA_COR_ECC_ERR_EN BIT(4) |
| #define REG_IRQ_EN_CHA_LLP_ERR_EN BIT(3) |
| #define REG_IRQ_EN_CHA_SOT_BIT_ERR_EN BIT(2) |
| #define REG_IRQ_EN_CHA_PLL_UNLOCK_EN BIT(0) |
| #define REG_IRQ_STAT 0xe5 |
| #define REG_IRQ_STAT_CHA_SYNCH_ERR BIT(7) |
| #define REG_IRQ_STAT_CHA_CRC_ERR BIT(6) |
| #define REG_IRQ_STAT_CHA_UNC_ECC_ERR BIT(5) |
| #define REG_IRQ_STAT_CHA_COR_ECC_ERR BIT(4) |
| #define REG_IRQ_STAT_CHA_LLP_ERR BIT(3) |
| #define REG_IRQ_STAT_CHA_SOT_BIT_ERR BIT(2) |
| #define REG_IRQ_STAT_CHA_PLL_UNLOCK BIT(0) |
| |
| enum sn65dsi83_model { |
| MODEL_SN65DSI83, |
| MODEL_SN65DSI84, |
| }; |
| |
| struct sn65dsi83 { |
| struct drm_bridge bridge; |
| struct device *dev; |
| struct regmap *regmap; |
| struct device_node *host_node; |
| struct mipi_dsi_device *dsi; |
| struct drm_bridge *panel_bridge; |
| struct gpio_desc *enable_gpio; |
| int dsi_lanes; |
| bool lvds_dual_link; |
| bool lvds_dual_link_even_odd_swap; |
| }; |
| |
| static const struct regmap_range sn65dsi83_readable_ranges[] = { |
| regmap_reg_range(REG_ID(0), REG_ID(8)), |
| regmap_reg_range(REG_RC_LVDS_PLL, REG_RC_DSI_CLK), |
| regmap_reg_range(REG_RC_PLL_EN, REG_RC_PLL_EN), |
| regmap_reg_range(REG_DSI_LANE, REG_DSI_CLK), |
| regmap_reg_range(REG_LVDS_FMT, REG_LVDS_CM), |
| regmap_reg_range(REG_VID_CHA_ACTIVE_LINE_LENGTH_LOW, |
| REG_VID_CHA_ACTIVE_LINE_LENGTH_HIGH), |
| regmap_reg_range(REG_VID_CHA_VERTICAL_DISPLAY_SIZE_LOW, |
| REG_VID_CHA_VERTICAL_DISPLAY_SIZE_HIGH), |
| regmap_reg_range(REG_VID_CHA_SYNC_DELAY_LOW, |
| REG_VID_CHA_SYNC_DELAY_HIGH), |
| regmap_reg_range(REG_VID_CHA_HSYNC_PULSE_WIDTH_LOW, |
| REG_VID_CHA_HSYNC_PULSE_WIDTH_HIGH), |
| regmap_reg_range(REG_VID_CHA_VSYNC_PULSE_WIDTH_LOW, |
| REG_VID_CHA_VSYNC_PULSE_WIDTH_HIGH), |
| regmap_reg_range(REG_VID_CHA_HORIZONTAL_BACK_PORCH, |
| REG_VID_CHA_HORIZONTAL_BACK_PORCH), |
| regmap_reg_range(REG_VID_CHA_VERTICAL_BACK_PORCH, |
| REG_VID_CHA_VERTICAL_BACK_PORCH), |
| regmap_reg_range(REG_VID_CHA_HORIZONTAL_FRONT_PORCH, |
| REG_VID_CHA_HORIZONTAL_FRONT_PORCH), |
| regmap_reg_range(REG_VID_CHA_VERTICAL_FRONT_PORCH, |
| REG_VID_CHA_VERTICAL_FRONT_PORCH), |
| regmap_reg_range(REG_VID_CHA_TEST_PATTERN, REG_VID_CHA_TEST_PATTERN), |
| regmap_reg_range(REG_IRQ_GLOBAL, REG_IRQ_EN), |
| regmap_reg_range(REG_IRQ_STAT, REG_IRQ_STAT), |
| }; |
| |
| static const struct regmap_access_table sn65dsi83_readable_table = { |
| .yes_ranges = sn65dsi83_readable_ranges, |
| .n_yes_ranges = ARRAY_SIZE(sn65dsi83_readable_ranges), |
| }; |
| |
| static const struct regmap_range sn65dsi83_writeable_ranges[] = { |
| regmap_reg_range(REG_RC_RESET, REG_RC_DSI_CLK), |
| regmap_reg_range(REG_RC_PLL_EN, REG_RC_PLL_EN), |
| regmap_reg_range(REG_DSI_LANE, REG_DSI_CLK), |
| regmap_reg_range(REG_LVDS_FMT, REG_LVDS_CM), |
| regmap_reg_range(REG_VID_CHA_ACTIVE_LINE_LENGTH_LOW, |
| REG_VID_CHA_ACTIVE_LINE_LENGTH_HIGH), |
| regmap_reg_range(REG_VID_CHA_VERTICAL_DISPLAY_SIZE_LOW, |
| REG_VID_CHA_VERTICAL_DISPLAY_SIZE_HIGH), |
| regmap_reg_range(REG_VID_CHA_SYNC_DELAY_LOW, |
| REG_VID_CHA_SYNC_DELAY_HIGH), |
| regmap_reg_range(REG_VID_CHA_HSYNC_PULSE_WIDTH_LOW, |
| REG_VID_CHA_HSYNC_PULSE_WIDTH_HIGH), |
| regmap_reg_range(REG_VID_CHA_VSYNC_PULSE_WIDTH_LOW, |
| REG_VID_CHA_VSYNC_PULSE_WIDTH_HIGH), |
| regmap_reg_range(REG_VID_CHA_HORIZONTAL_BACK_PORCH, |
| REG_VID_CHA_HORIZONTAL_BACK_PORCH), |
| regmap_reg_range(REG_VID_CHA_VERTICAL_BACK_PORCH, |
| REG_VID_CHA_VERTICAL_BACK_PORCH), |
| regmap_reg_range(REG_VID_CHA_HORIZONTAL_FRONT_PORCH, |
| REG_VID_CHA_HORIZONTAL_FRONT_PORCH), |
| regmap_reg_range(REG_VID_CHA_VERTICAL_FRONT_PORCH, |
| REG_VID_CHA_VERTICAL_FRONT_PORCH), |
| regmap_reg_range(REG_VID_CHA_TEST_PATTERN, REG_VID_CHA_TEST_PATTERN), |
| regmap_reg_range(REG_IRQ_GLOBAL, REG_IRQ_EN), |
| regmap_reg_range(REG_IRQ_STAT, REG_IRQ_STAT), |
| }; |
| |
| static const struct regmap_access_table sn65dsi83_writeable_table = { |
| .yes_ranges = sn65dsi83_writeable_ranges, |
| .n_yes_ranges = ARRAY_SIZE(sn65dsi83_writeable_ranges), |
| }; |
| |
| static const struct regmap_range sn65dsi83_volatile_ranges[] = { |
| regmap_reg_range(REG_RC_RESET, REG_RC_RESET), |
| regmap_reg_range(REG_RC_LVDS_PLL, REG_RC_LVDS_PLL), |
| regmap_reg_range(REG_IRQ_STAT, REG_IRQ_STAT), |
| }; |
| |
| static const struct regmap_access_table sn65dsi83_volatile_table = { |
| .yes_ranges = sn65dsi83_volatile_ranges, |
| .n_yes_ranges = ARRAY_SIZE(sn65dsi83_volatile_ranges), |
| }; |
| |
| static const struct regmap_config sn65dsi83_regmap_config = { |
| .reg_bits = 8, |
| .val_bits = 8, |
| .rd_table = &sn65dsi83_readable_table, |
| .wr_table = &sn65dsi83_writeable_table, |
| .volatile_table = &sn65dsi83_volatile_table, |
| .cache_type = REGCACHE_RBTREE, |
| .max_register = REG_IRQ_STAT, |
| }; |
| |
| static struct sn65dsi83 *bridge_to_sn65dsi83(struct drm_bridge *bridge) |
| { |
| return container_of(bridge, struct sn65dsi83, bridge); |
| } |
| |
| static int sn65dsi83_attach(struct drm_bridge *bridge, |
| enum drm_bridge_attach_flags flags) |
| { |
| struct sn65dsi83 *ctx = bridge_to_sn65dsi83(bridge); |
| struct device *dev = ctx->dev; |
| struct mipi_dsi_device *dsi; |
| struct mipi_dsi_host *host; |
| int ret = 0; |
| |
| const struct mipi_dsi_device_info info = { |
| .type = "sn65dsi83", |
| .channel = 0, |
| .node = NULL, |
| }; |
| |
| host = of_find_mipi_dsi_host_by_node(ctx->host_node); |
| if (!host) { |
| dev_err(dev, "failed to find dsi host\n"); |
| return -EPROBE_DEFER; |
| } |
| |
| dsi = mipi_dsi_device_register_full(host, &info); |
| if (IS_ERR(dsi)) { |
| return dev_err_probe(dev, PTR_ERR(dsi), |
| "failed to create dsi device\n"); |
| } |
| |
| ctx->dsi = dsi; |
| |
| dsi->lanes = ctx->dsi_lanes; |
| dsi->format = MIPI_DSI_FMT_RGB888; |
| dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST; |
| |
| ret = mipi_dsi_attach(dsi); |
| if (ret < 0) { |
| dev_err(dev, "failed to attach dsi to host\n"); |
| goto err_dsi_attach; |
| } |
| |
| return drm_bridge_attach(bridge->encoder, ctx->panel_bridge, |
| &ctx->bridge, flags); |
| |
| err_dsi_attach: |
| mipi_dsi_device_unregister(dsi); |
| return ret; |
| } |
| |
| static void sn65dsi83_atomic_pre_enable(struct drm_bridge *bridge, |
| struct drm_bridge_state *old_bridge_state) |
| { |
| struct sn65dsi83 *ctx = bridge_to_sn65dsi83(bridge); |
| |
| /* |
| * Reset the chip, pull EN line low for t_reset=10ms, |
| * then high for t_en=1ms. |
| */ |
| regcache_mark_dirty(ctx->regmap); |
| gpiod_set_value(ctx->enable_gpio, 0); |
| usleep_range(10000, 11000); |
| gpiod_set_value(ctx->enable_gpio, 1); |
| usleep_range(1000, 1100); |
| } |
| |
| static u8 sn65dsi83_get_lvds_range(struct sn65dsi83 *ctx, |
| const struct drm_display_mode *mode) |
| { |
| /* |
| * The encoding of the LVDS_CLK_RANGE is as follows: |
| * 000 - 25 MHz <= LVDS_CLK < 37.5 MHz |
| * 001 - 37.5 MHz <= LVDS_CLK < 62.5 MHz |
| * 010 - 62.5 MHz <= LVDS_CLK < 87.5 MHz |
| * 011 - 87.5 MHz <= LVDS_CLK < 112.5 MHz |
| * 100 - 112.5 MHz <= LVDS_CLK < 137.5 MHz |
| * 101 - 137.5 MHz <= LVDS_CLK <= 154 MHz |
| * which is a range of 12.5MHz..162.5MHz in 50MHz steps, except that |
| * the ends of the ranges are clamped to the supported range. Since |
| * sn65dsi83_mode_valid() already filters the valid modes and limits |
| * the clock to 25..154 MHz, the range calculation can be simplified |
| * as follows: |
| */ |
| int mode_clock = mode->clock; |
| |
| if (ctx->lvds_dual_link) |
| mode_clock /= 2; |
| |
| return (mode_clock - 12500) / 25000; |
| } |
| |
| static u8 sn65dsi83_get_dsi_range(struct sn65dsi83 *ctx, |
| const struct drm_display_mode *mode) |
| { |
| /* |
| * The encoding of the CHA_DSI_CLK_RANGE is as follows: |
| * 0x00 through 0x07 - Reserved |
| * 0x08 - 40 <= DSI_CLK < 45 MHz |
| * 0x09 - 45 <= DSI_CLK < 50 MHz |
| * ... |
| * 0x63 - 495 <= DSI_CLK < 500 MHz |
| * 0x64 - 500 MHz |
| * 0x65 through 0xFF - Reserved |
| * which is DSI clock in 5 MHz steps, clamped to 40..500 MHz. |
| * The DSI clock are calculated as: |
| * DSI_CLK = mode clock * bpp / dsi_data_lanes / 2 |
| * the 2 is there because the bus is DDR. |
| */ |
| return DIV_ROUND_UP(clamp((unsigned int)mode->clock * |
| mipi_dsi_pixel_format_to_bpp(ctx->dsi->format) / |
| ctx->dsi_lanes / 2, 40000U, 500000U), 5000U); |
| } |
| |
| static u8 sn65dsi83_get_dsi_div(struct sn65dsi83 *ctx) |
| { |
| /* The divider is (DSI_CLK / LVDS_CLK) - 1, which really is: */ |
| unsigned int dsi_div = mipi_dsi_pixel_format_to_bpp(ctx->dsi->format); |
| |
| dsi_div /= ctx->dsi_lanes; |
| |
| if (!ctx->lvds_dual_link) |
| dsi_div /= 2; |
| |
| return dsi_div - 1; |
| } |
| |
| static void sn65dsi83_atomic_enable(struct drm_bridge *bridge, |
| struct drm_bridge_state *old_bridge_state) |
| { |
| struct sn65dsi83 *ctx = bridge_to_sn65dsi83(bridge); |
| struct drm_atomic_state *state = old_bridge_state->base.state; |
| const struct drm_bridge_state *bridge_state; |
| const struct drm_crtc_state *crtc_state; |
| const struct drm_display_mode *mode; |
| struct drm_connector *connector; |
| struct drm_crtc *crtc; |
| bool lvds_format_24bpp; |
| bool lvds_format_jeida; |
| unsigned int pval; |
| __le16 le16val; |
| u16 val; |
| int ret; |
| |
| /* Get the LVDS format from the bridge state. */ |
| bridge_state = drm_atomic_get_new_bridge_state(state, bridge); |
| |
| switch (bridge_state->output_bus_cfg.format) { |
| case MEDIA_BUS_FMT_RGB666_1X7X3_SPWG: |
| lvds_format_24bpp = false; |
| lvds_format_jeida = true; |
| break; |
| case MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA: |
| lvds_format_24bpp = true; |
| lvds_format_jeida = true; |
| break; |
| case MEDIA_BUS_FMT_RGB888_1X7X4_SPWG: |
| lvds_format_24bpp = true; |
| lvds_format_jeida = false; |
| break; |
| default: |
| /* |
| * Some bridges still don't set the correct |
| * LVDS bus pixel format, use SPWG24 default |
| * format until those are fixed. |
| */ |
| lvds_format_24bpp = true; |
| lvds_format_jeida = false; |
| dev_warn(ctx->dev, |
| "Unsupported LVDS bus format 0x%04x, please check output bridge driver. Falling back to SPWG24.\n", |
| bridge_state->output_bus_cfg.format); |
| break; |
| } |
| |
| /* |
| * Retrieve the CRTC adjusted mode. This requires a little dance to go |
| * from the bridge to the encoder, to the connector and to the CRTC. |
| */ |
| connector = drm_atomic_get_new_connector_for_encoder(state, |
| bridge->encoder); |
| crtc = drm_atomic_get_new_connector_state(state, connector)->crtc; |
| crtc_state = drm_atomic_get_new_crtc_state(state, crtc); |
| mode = &crtc_state->adjusted_mode; |
| |
| /* Clear reset, disable PLL */ |
| regmap_write(ctx->regmap, REG_RC_RESET, 0x00); |
| regmap_write(ctx->regmap, REG_RC_PLL_EN, 0x00); |
| |
| /* Reference clock derived from DSI link clock. */ |
| regmap_write(ctx->regmap, REG_RC_LVDS_PLL, |
| REG_RC_LVDS_PLL_LVDS_CLK_RANGE(sn65dsi83_get_lvds_range(ctx, mode)) | |
| REG_RC_LVDS_PLL_HS_CLK_SRC_DPHY); |
| regmap_write(ctx->regmap, REG_DSI_CLK, |
| REG_DSI_CLK_CHA_DSI_CLK_RANGE(sn65dsi83_get_dsi_range(ctx, mode))); |
| regmap_write(ctx->regmap, REG_RC_DSI_CLK, |
| REG_RC_DSI_CLK_DSI_CLK_DIVIDER(sn65dsi83_get_dsi_div(ctx))); |
| |
| /* Set number of DSI lanes and LVDS link config. */ |
| regmap_write(ctx->regmap, REG_DSI_LANE, |
| REG_DSI_LANE_DSI_CHANNEL_MODE_SINGLE | |
| REG_DSI_LANE_CHA_DSI_LANES(~(ctx->dsi_lanes - 1)) | |
| /* CHB is DSI85-only, set to default on DSI83/DSI84 */ |
| REG_DSI_LANE_CHB_DSI_LANES(3)); |
| /* No equalization. */ |
| regmap_write(ctx->regmap, REG_DSI_EQ, 0x00); |
| |
| /* Set up sync signal polarity. */ |
| val = (mode->flags & DRM_MODE_FLAG_NHSYNC ? |
| REG_LVDS_FMT_HS_NEG_POLARITY : 0) | |
| (mode->flags & DRM_MODE_FLAG_NVSYNC ? |
| REG_LVDS_FMT_VS_NEG_POLARITY : 0); |
| |
| /* Set up bits-per-pixel, 18bpp or 24bpp. */ |
| if (lvds_format_24bpp) { |
| val |= REG_LVDS_FMT_CHA_24BPP_MODE; |
| if (ctx->lvds_dual_link) |
| val |= REG_LVDS_FMT_CHB_24BPP_MODE; |
| } |
| |
| /* Set up LVDS format, JEIDA/Format 1 or SPWG/Format 2 */ |
| if (lvds_format_jeida) { |
| val |= REG_LVDS_FMT_CHA_24BPP_FORMAT1; |
| if (ctx->lvds_dual_link) |
| val |= REG_LVDS_FMT_CHB_24BPP_FORMAT1; |
| } |
| |
| /* Set up LVDS output config (DSI84,DSI85) */ |
| if (!ctx->lvds_dual_link) |
| val |= REG_LVDS_FMT_LVDS_LINK_CFG; |
| |
| regmap_write(ctx->regmap, REG_LVDS_FMT, val); |
| regmap_write(ctx->regmap, REG_LVDS_VCOM, 0x05); |
| regmap_write(ctx->regmap, REG_LVDS_LANE, |
| (ctx->lvds_dual_link_even_odd_swap ? |
| REG_LVDS_LANE_EVEN_ODD_SWAP : 0) | |
| REG_LVDS_LANE_CHA_LVDS_TERM | |
| REG_LVDS_LANE_CHB_LVDS_TERM); |
| regmap_write(ctx->regmap, REG_LVDS_CM, 0x00); |
| |
| le16val = cpu_to_le16(mode->hdisplay); |
| regmap_bulk_write(ctx->regmap, REG_VID_CHA_ACTIVE_LINE_LENGTH_LOW, |
| &le16val, 2); |
| le16val = cpu_to_le16(mode->vdisplay); |
| regmap_bulk_write(ctx->regmap, REG_VID_CHA_VERTICAL_DISPLAY_SIZE_LOW, |
| &le16val, 2); |
| /* 32 + 1 pixel clock to ensure proper operation */ |
| le16val = cpu_to_le16(32 + 1); |
| regmap_bulk_write(ctx->regmap, REG_VID_CHA_SYNC_DELAY_LOW, &le16val, 2); |
| le16val = cpu_to_le16(mode->hsync_end - mode->hsync_start); |
| regmap_bulk_write(ctx->regmap, REG_VID_CHA_HSYNC_PULSE_WIDTH_LOW, |
| &le16val, 2); |
| le16val = cpu_to_le16(mode->vsync_end - mode->vsync_start); |
| regmap_bulk_write(ctx->regmap, REG_VID_CHA_VSYNC_PULSE_WIDTH_LOW, |
| &le16val, 2); |
| regmap_write(ctx->regmap, REG_VID_CHA_HORIZONTAL_BACK_PORCH, |
| mode->htotal - mode->hsync_end); |
| regmap_write(ctx->regmap, REG_VID_CHA_VERTICAL_BACK_PORCH, |
| mode->vtotal - mode->vsync_end); |
| regmap_write(ctx->regmap, REG_VID_CHA_HORIZONTAL_FRONT_PORCH, |
| mode->hsync_start - mode->hdisplay); |
| regmap_write(ctx->regmap, REG_VID_CHA_VERTICAL_FRONT_PORCH, |
| mode->vsync_start - mode->vdisplay); |
| regmap_write(ctx->regmap, REG_VID_CHA_TEST_PATTERN, 0x00); |
| |
| /* Enable PLL */ |
| regmap_write(ctx->regmap, REG_RC_PLL_EN, REG_RC_PLL_EN_PLL_EN); |
| usleep_range(3000, 4000); |
| ret = regmap_read_poll_timeout(ctx->regmap, REG_RC_LVDS_PLL, pval, |
| pval & REG_RC_LVDS_PLL_PLL_EN_STAT, |
| 1000, 100000); |
| if (ret) { |
| dev_err(ctx->dev, "failed to lock PLL, ret=%i\n", ret); |
| /* On failure, disable PLL again and exit. */ |
| regmap_write(ctx->regmap, REG_RC_PLL_EN, 0x00); |
| return; |
| } |
| |
| /* Trigger reset after CSR register update. */ |
| regmap_write(ctx->regmap, REG_RC_RESET, REG_RC_RESET_SOFT_RESET); |
| |
| /* Clear all errors that got asserted during initialization. */ |
| regmap_read(ctx->regmap, REG_IRQ_STAT, &pval); |
| regmap_write(ctx->regmap, REG_IRQ_STAT, pval); |
| } |
| |
| static void sn65dsi83_atomic_disable(struct drm_bridge *bridge, |
| struct drm_bridge_state *old_bridge_state) |
| { |
| struct sn65dsi83 *ctx = bridge_to_sn65dsi83(bridge); |
| |
| /* Clear reset, disable PLL */ |
| regmap_write(ctx->regmap, REG_RC_RESET, 0x00); |
| regmap_write(ctx->regmap, REG_RC_PLL_EN, 0x00); |
| } |
| |
| static void sn65dsi83_atomic_post_disable(struct drm_bridge *bridge, |
| struct drm_bridge_state *old_bridge_state) |
| { |
| struct sn65dsi83 *ctx = bridge_to_sn65dsi83(bridge); |
| |
| /* Put the chip in reset, pull EN line low. */ |
| gpiod_set_value(ctx->enable_gpio, 0); |
| } |
| |
| static enum drm_mode_status |
| sn65dsi83_mode_valid(struct drm_bridge *bridge, |
| const struct drm_display_info *info, |
| const struct drm_display_mode *mode) |
| { |
| /* LVDS output clock range 25..154 MHz */ |
| if (mode->clock < 25000) |
| return MODE_CLOCK_LOW; |
| if (mode->clock > 154000) |
| return MODE_CLOCK_HIGH; |
| |
| return MODE_OK; |
| } |
| |
| #define MAX_INPUT_SEL_FORMATS 1 |
| |
| static u32 * |
| sn65dsi83_atomic_get_input_bus_fmts(struct drm_bridge *bridge, |
| struct drm_bridge_state *bridge_state, |
| struct drm_crtc_state *crtc_state, |
| struct drm_connector_state *conn_state, |
| u32 output_fmt, |
| unsigned int *num_input_fmts) |
| { |
| u32 *input_fmts; |
| |
| *num_input_fmts = 0; |
| |
| input_fmts = kcalloc(MAX_INPUT_SEL_FORMATS, sizeof(*input_fmts), |
| GFP_KERNEL); |
| if (!input_fmts) |
| return NULL; |
| |
| /* This is the DSI-end bus format */ |
| input_fmts[0] = MEDIA_BUS_FMT_RGB888_1X24; |
| *num_input_fmts = 1; |
| |
| return input_fmts; |
| } |
| |
| static const struct drm_bridge_funcs sn65dsi83_funcs = { |
| .attach = sn65dsi83_attach, |
| .atomic_pre_enable = sn65dsi83_atomic_pre_enable, |
| .atomic_enable = sn65dsi83_atomic_enable, |
| .atomic_disable = sn65dsi83_atomic_disable, |
| .atomic_post_disable = sn65dsi83_atomic_post_disable, |
| .mode_valid = sn65dsi83_mode_valid, |
| |
| .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, |
| .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, |
| .atomic_reset = drm_atomic_helper_bridge_reset, |
| .atomic_get_input_bus_fmts = sn65dsi83_atomic_get_input_bus_fmts, |
| }; |
| |
| static int sn65dsi83_parse_dt(struct sn65dsi83 *ctx, enum sn65dsi83_model model) |
| { |
| struct drm_bridge *panel_bridge; |
| struct device *dev = ctx->dev; |
| struct device_node *endpoint; |
| struct drm_panel *panel; |
| int ret; |
| |
| endpoint = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0); |
| ctx->dsi_lanes = of_property_count_u32_elems(endpoint, "data-lanes"); |
| ctx->host_node = of_graph_get_remote_port_parent(endpoint); |
| of_node_put(endpoint); |
| |
| if (ctx->dsi_lanes < 0 || ctx->dsi_lanes > 4) |
| return -EINVAL; |
| if (!ctx->host_node) |
| return -ENODEV; |
| |
| ctx->lvds_dual_link = false; |
| ctx->lvds_dual_link_even_odd_swap = false; |
| if (model != MODEL_SN65DSI83) { |
| struct device_node *port2, *port3; |
| int dual_link; |
| |
| port2 = of_graph_get_port_by_id(dev->of_node, 2); |
| port3 = of_graph_get_port_by_id(dev->of_node, 3); |
| dual_link = drm_of_lvds_get_dual_link_pixel_order(port2, port3); |
| of_node_put(port2); |
| of_node_put(port3); |
| |
| if (dual_link == DRM_LVDS_DUAL_LINK_ODD_EVEN_PIXELS) { |
| ctx->lvds_dual_link = true; |
| /* Odd pixels to LVDS Channel A, even pixels to B */ |
| ctx->lvds_dual_link_even_odd_swap = false; |
| } else if (dual_link == DRM_LVDS_DUAL_LINK_EVEN_ODD_PIXELS) { |
| ctx->lvds_dual_link = true; |
| /* Even pixels to LVDS Channel A, odd pixels to B */ |
| ctx->lvds_dual_link_even_odd_swap = true; |
| } |
| } |
| |
| ret = drm_of_find_panel_or_bridge(dev->of_node, 2, 0, &panel, &panel_bridge); |
| if (ret < 0) |
| return ret; |
| if (panel) { |
| panel_bridge = devm_drm_panel_bridge_add(dev, panel); |
| if (IS_ERR(panel_bridge)) |
| return PTR_ERR(panel_bridge); |
| } |
| |
| ctx->panel_bridge = panel_bridge; |
| |
| return 0; |
| } |
| |
| static int sn65dsi83_probe(struct i2c_client *client, |
| const struct i2c_device_id *id) |
| { |
| struct device *dev = &client->dev; |
| enum sn65dsi83_model model; |
| struct sn65dsi83 *ctx; |
| int ret; |
| |
| ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); |
| if (!ctx) |
| return -ENOMEM; |
| |
| ctx->dev = dev; |
| |
| if (dev->of_node) { |
| model = (enum sn65dsi83_model)(uintptr_t) |
| of_device_get_match_data(dev); |
| } else { |
| model = id->driver_data; |
| } |
| |
| ctx->enable_gpio = devm_gpiod_get(ctx->dev, "enable", GPIOD_OUT_LOW); |
| if (IS_ERR(ctx->enable_gpio)) |
| return PTR_ERR(ctx->enable_gpio); |
| |
| ret = sn65dsi83_parse_dt(ctx, model); |
| if (ret) |
| return ret; |
| |
| ctx->regmap = devm_regmap_init_i2c(client, &sn65dsi83_regmap_config); |
| if (IS_ERR(ctx->regmap)) |
| return PTR_ERR(ctx->regmap); |
| |
| dev_set_drvdata(dev, ctx); |
| i2c_set_clientdata(client, ctx); |
| |
| ctx->bridge.funcs = &sn65dsi83_funcs; |
| ctx->bridge.of_node = dev->of_node; |
| drm_bridge_add(&ctx->bridge); |
| |
| return 0; |
| } |
| |
| static int sn65dsi83_remove(struct i2c_client *client) |
| { |
| struct sn65dsi83 *ctx = i2c_get_clientdata(client); |
| |
| mipi_dsi_detach(ctx->dsi); |
| mipi_dsi_device_unregister(ctx->dsi); |
| drm_bridge_remove(&ctx->bridge); |
| of_node_put(ctx->host_node); |
| |
| return 0; |
| } |
| |
| static struct i2c_device_id sn65dsi83_id[] = { |
| { "ti,sn65dsi83", MODEL_SN65DSI83 }, |
| { "ti,sn65dsi84", MODEL_SN65DSI84 }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(i2c, sn65dsi83_id); |
| |
| static const struct of_device_id sn65dsi83_match_table[] = { |
| { .compatible = "ti,sn65dsi83", .data = (void *)MODEL_SN65DSI83 }, |
| { .compatible = "ti,sn65dsi84", .data = (void *)MODEL_SN65DSI84 }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, sn65dsi83_match_table); |
| |
| static struct i2c_driver sn65dsi83_driver = { |
| .probe = sn65dsi83_probe, |
| .remove = sn65dsi83_remove, |
| .id_table = sn65dsi83_id, |
| .driver = { |
| .name = "sn65dsi83", |
| .of_match_table = sn65dsi83_match_table, |
| }, |
| }; |
| module_i2c_driver(sn65dsi83_driver); |
| |
| MODULE_AUTHOR("Marek Vasut <marex@denx.de>"); |
| MODULE_DESCRIPTION("TI SN65DSI83 DSI to LVDS bridge driver"); |
| MODULE_LICENSE("GPL v2"); |