blob: 0691361701985caba21c0a8634560aa319550385 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
#include "qcom-msm8974.dtsi"
#include "qcom-pm8841.dtsi"
#include "qcom-pm8941.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
/ {
model = "LGE MSM 8974 HAMMERHEAD";
compatible = "lge,hammerhead", "qcom,msm8974";
aliases {
serial0 = &blsp1_uart1;
serial1 = &blsp2_uart10;
};
chosen {
stdout-path = "serial0:115200n8";
};
smd {
rpm {
rpm_requests {
pm8841-regulators {
s1 {
regulator-min-microvolt = <675000>;
regulator-max-microvolt = <1050000>;
};
s2 {
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1050000>;
};
s3 {
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1050000>;
};
s4 {
regulator-min-microvolt = <815000>;
regulator-max-microvolt = <900000>;
};
};
pm8941-regulators {
vdd_l1_l3-supply = <&pm8941_s1>;
vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
vdd_l4_l11-supply = <&pm8941_s1>;
vdd_l5_l7-supply = <&pm8941_s2>;
vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
vdd_l21-supply = <&vreg_boost>;
s1 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
regulator-boot-on;
};
s2 {
regulator-min-microvolt = <2150000>;
regulator-max-microvolt = <2150000>;
regulator-boot-on;
};
s3 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
l1 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
regulator-always-on;
regulator-boot-on;
};
l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
l3 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
};
l4 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
};
l5 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l6 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
};
l7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
};
l8 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l9 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
};
l10 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
};
l11 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
};
l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
l13 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
regulator-boot-on;
};
l14 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l15 {
regulator-min-microvolt = <2050000>;
regulator-max-microvolt = <2050000>;
};
l16 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
l17 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
};
l18 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
};
l19 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3300000>;
};
l20 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
regulator-boot-on;
regulator-system-load = <200000>;
regulator-allow-set-load;
};
l21 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
regulator-boot-on;
};
l22 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3300000>;
};
l23 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
l24 {
regulator-min-microvolt = <3075000>;
regulator-max-microvolt = <3075000>;
regulator-boot-on;
};
};
};
};
};
vreg_wlan: wlan-regulator {
compatible = "regulator-fixed";
regulator-name = "wl-reg";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&msmgpio 26 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
pinctrl-0 = <&wlan_regulator_pin>;
};
};
&soc {
serial@f991d000 {
status = "okay";
};
pinctrl@fd510000 {
sdhc1_pin_a: sdhc1-pin-active {
clk {
pins = "sdc1_clk";
drive-strength = <16>;
bias-disable;
};
cmd-data {
pins = "sdc1_cmd", "sdc1_data";
drive-strength = <10>;
bias-pull-up;
};
};
sdhc2_pin_a: sdhc2-pin-active {
clk {
pins = "sdc2_clk";
drive-strength = <6>;
bias-disable;
};
cmd-data {
pins = "sdc2_cmd", "sdc2_data";
drive-strength = <6>;
bias-pull-up;
};
};
i2c1_pins: i2c1 {
mux {
pins = "gpio2", "gpio3";
function = "blsp_i2c1";
drive-strength = <2>;
bias-disable;
};
};
i2c2_pins: i2c2 {
mux {
pins = "gpio6", "gpio7";
function = "blsp_i2c2";
drive-strength = <2>;
bias-disable;
};
};
i2c3_pins: i2c3 {
mux {
pins = "gpio10", "gpio11";
function = "blsp_i2c3";
drive-strength = <2>;
bias-disable;
};
};
i2c11_pins: i2c11 {
mux {
pins = "gpio83", "gpio84";
function = "blsp_i2c11";
drive-strength = <2>;
bias-disable;
};
};
i2c12_pins: i2c12 {
mux {
pins = "gpio87", "gpio88";
function = "blsp_i2c12";
drive-strength = <2>;
bias-disable;
};
};
mpu6515_pin: mpu6515 {
irq {
pins = "gpio73";
function = "gpio";
bias-disable;
input-enable;
};
};
touch_pin: touch {
int {
pins = "gpio5";
function = "gpio";
drive-strength = <2>;
bias-disable;
input-enable;
};
reset {
pins = "gpio8";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
panel_pin: panel {
te {
pins = "gpio12";
function = "mdp_vsync";
drive-strength = <2>;
bias-disable;
};
};
bt_pin: bt {
hostwake {
pins = "gpio42";
function = "gpio";
};
devwake {
pins = "gpio62";
function = "gpio";
};
shutdown {
pins = "gpio41";
function = "gpio";
};
};
blsp2_uart10_pin_a: blsp2-uart10-pin-active {
tx {
pins = "gpio53";
function = "blsp_uart10";
drive-strength = <2>;
bias-disable;
};
rx {
pins = "gpio54";
function = "blsp_uart10";
drive-strength = <2>;
bias-pull-up;
};
cts {
pins = "gpio55";
function = "blsp_uart10";
drive-strength = <2>;
bias-pull-up;
};
rts {
pins = "gpio56";
function = "blsp_uart10";
drive-strength = <2>;
bias-disable;
};
};
};
sdhci@f9824900 {
status = "okay";
vmmc-supply = <&pm8941_l20>;
vqmmc-supply = <&pm8941_s3>;
bus-width = <8>;
non-removable;
pinctrl-names = "default";
pinctrl-0 = <&sdhc1_pin_a>;
};
sdhci@f98a4900 {
status = "okay";
max-frequency = <100000000>;
bus-width = <4>;
non-removable;
vmmc-supply = <&vreg_wlan>;
vqmmc-supply = <&pm8941_s3>;
pinctrl-names = "default";
pinctrl-0 = <&sdhc2_pin_a>;
#address-cells = <1>;
#size-cells = <0>;
bcrmf@1 {
compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
reg = <1>;
brcm,drive-strength = <10>;
pinctrl-names = "default";
pinctrl-0 = <&wlan_sleep_clk_pin>;
};
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&gpio_keys_pin_a>;
volume-up {
label = "volume_up";
gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
linux,input-type = <1>;
linux,code = <KEY_VOLUMEUP>;
};
volume-down {
label = "volume_down";
gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
linux,input-type = <1>;
linux,code = <KEY_VOLUMEDOWN>;
};
};
serial@f9960000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&blsp2_uart10_pin_a>;
bluetooth {
compatible = "brcm,bcm43438-bt";
max-speed = <3000000>;
pinctrl-names = "default";
pinctrl-0 = <&bt_pin>;
host-wakeup-gpios = <&msmgpio 42 GPIO_ACTIVE_HIGH>;
device-wakeup-gpios = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
shutdown-gpios = <&msmgpio 41 GPIO_ACTIVE_HIGH>;
};
};
i2c@f9967000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c11_pins>;
clock-frequency = <355000>;
qcom,src-freq = <50000000>;
led-controller@38 {
compatible = "ti,lm3630a";
status = "okay";
reg = <0x38>;
#address-cells = <1>;
#size-cells = <0>;
led@0 {
reg = <0>;
led-sources = <0 1>;
label = "lcd-backlight";
default-brightness = <200>;
};
};
};
i2c@f9968000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c12_pins>;
clock-frequency = <100000>;
qcom,src-freq = <50000000>;
mpu6515@68 {
compatible = "invensense,mpu6515";
reg = <0x68>;
interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>;
vddio-supply = <&pm8941_lvs1>;
pinctrl-names = "default";
pinctrl-0 = <&mpu6515_pin>;
mount-matrix = "0", "-1", "0",
"-1", "0", "0",
"0", "0", "1";
i2c-gate {
#address-cells = <1>;
#size-cells = <0>;
ak8963@f {
compatible = "asahi-kasei,ak8963";
reg = <0x0f>;
gpios = <&msmgpio 67 0>;
vid-supply = <&pm8941_lvs1>;
vdd-supply = <&pm8941_l17>;
};
bmp280@76 {
compatible = "bosch,bmp280";
reg = <0x76>;
vdda-supply = <&pm8941_lvs1>;
vddd-supply = <&pm8941_l17>;
};
};
};
};
i2c@f9923000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <100000>;
qcom,src-freq = <50000000>;
charger: bq24192@6b {
compatible = "ti,bq24192";
reg = <0x6b>;
interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
omit-battery-class;
usb_otg_vbus: usb-otg-vbus { };
};
fuelgauge: max17048@36 {
compatible = "maxim,max17048";
reg = <0x36>;
maxim,double-soc;
maxim,rcomp = /bits/ 8 <0x4d>;
interrupt-parent = <&msmgpio>;
interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&fuelgauge_pin>;
maxim,alert-low-soc-level = <2>;
};
};
i2c@f9924000 {
status = "okay";
clock-frequency = <355000>;
qcom,src-freq = <50000000>;
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
synaptics@70 {
compatible = "syna,rmi4-i2c";
reg = <0x70>;
interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>;
vdd-supply = <&pm8941_l22>;
vio-supply = <&pm8941_lvs3>;
pinctrl-names = "default";
pinctrl-0 = <&touch_pin>;
#address-cells = <1>;
#size-cells = <0>;
rmi4-f01@1 {
reg = <0x1>;
syna,nosleep-mode = <1>;
};
rmi4-f12@12 {
reg = <0x12>;
syna,sensor-type = <1>;
};
};
};
i2c@f9925000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins>;
clock-frequency = <100000>;
qcom,src-freq = <50000000>;
avago_apds993@39 {
compatible = "avago,apds9930";
reg = <0x39>;
interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
vdd-supply = <&pm8941_l17>;
vddio-supply = <&pm8941_lvs1>;
led-max-microamp = <100000>;
amstaos,proximity-diodes = <0>;
};
};
usb@f9a55000 {
status = "okay";
phys = <&usb_hs1_phy>;
phy-select = <&tcsr 0xb000 0>;
extcon = <&charger>, <&usb_id>;
vbus-supply = <&usb_otg_vbus>;
hnp-disable;
srp-disable;
adp-disable;
ulpi {
phy@a {
status = "okay";
v1p8-supply = <&pm8941_l6>;
v3p3-supply = <&pm8941_l24>;
qcom,init-seq = /bits/ 8 <0x1 0x64>;
};
};
};
mdss@fd900000 {
status = "okay";
mdp@fd900000 {
status = "okay";
};
dsi@fd922800 {
status = "okay";
vdda-supply = <&pm8941_l2>;
vdd-supply = <&pm8941_lvs3>;
vddio-supply = <&pm8941_l12>;
#address-cells = <1>;
#size-cells = <0>;
ports {
port@1 {
endpoint {
remote-endpoint = <&panel_in>;
data-lanes = <0 1 2 3>;
};
};
};
panel: panel@0 {
reg = <0>;
compatible = "lg,acx467akm-7";
pinctrl-names = "default";
pinctrl-0 = <&panel_pin>;
port {
panel_in: endpoint {
remote-endpoint = <&dsi0_out>;
};
};
};
};
dsi-phy@fd922a00 {
status = "okay";
vddio-supply = <&pm8941_l12>;
};
};
};
&spmi_bus {
pm8941@0 {
gpios@c000 {
gpio_keys_pin_a: gpio-keys-active {
pins = "gpio2", "gpio3";
function = "normal";
bias-pull-up;
power-source = <PM8941_GPIO_S3>;
};
fuelgauge_pin: fuelgauge-int {
pins = "gpio9";
function = "normal";
bias-disable;
input-enable;
power-source = <PM8941_GPIO_S3>;
};
wlan_sleep_clk_pin: wl-sleep-clk {
pins = "gpio16";
function = "func2";
output-high;
power-source = <PM8941_GPIO_S3>;
};
wlan_regulator_pin: wl-reg-active {
pins = "gpio17";
function = "normal";
bias-disable;
power-source = <PM8941_GPIO_S3>;
};
otg {
gpio-hog;
gpios = <35 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "otg-gpio";
};
};
};
};