| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (c) 2018 Amlogic, Inc. All rights reserved. |
| */ |
| |
| #include <dt-bindings/phy/phy.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/clock/g12a-clkc.h> |
| #include <dt-bindings/clock/g12a-aoclkc.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/interrupt-controller/amlogic,meson-g12a-gpio-intc.h> |
| #include <dt-bindings/reset/amlogic,meson-g12a-reset.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| / { |
| interrupt-parent = <&gic>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| aliases { |
| mmc0 = &sd_emmc_b; /* SD card */ |
| mmc1 = &sd_emmc_c; /* eMMC */ |
| mmc2 = &sd_emmc_a; /* SDIO */ |
| }; |
| |
| chosen { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| simplefb_cvbs: framebuffer-cvbs { |
| compatible = "amlogic,simple-framebuffer", |
| "simple-framebuffer"; |
| amlogic,pipeline = "vpu-cvbs"; |
| clocks = <&clkc CLKID_HDMI>, |
| <&clkc CLKID_HTX_PCLK>, |
| <&clkc CLKID_VPU_INTR>; |
| status = "disabled"; |
| }; |
| |
| simplefb_hdmi: framebuffer-hdmi { |
| compatible = "amlogic,simple-framebuffer", |
| "simple-framebuffer"; |
| amlogic,pipeline = "vpu-hdmi"; |
| clocks = <&clkc CLKID_HDMI>, |
| <&clkc CLKID_HTX_PCLK>, |
| <&clkc CLKID_VPU_INTR>; |
| status = "disabled"; |
| }; |
| }; |
| |
| efuse: efuse { |
| compatible = "amlogic,meson-gxbb-efuse"; |
| clocks = <&clkc CLKID_EFUSE>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| read-only; |
| secure-monitor = <&sm>; |
| }; |
| |
| gpu_opp_table: opp-table-gpu { |
| compatible = "operating-points-v2"; |
| |
| opp-124999998 { |
| opp-hz = /bits/ 64 <124999998>; |
| opp-microvolt = <800000>; |
| }; |
| opp-249999996 { |
| opp-hz = /bits/ 64 <249999996>; |
| opp-microvolt = <800000>; |
| }; |
| opp-285714281 { |
| opp-hz = /bits/ 64 <285714281>; |
| opp-microvolt = <800000>; |
| }; |
| opp-399999994 { |
| opp-hz = /bits/ 64 <399999994>; |
| opp-microvolt = <800000>; |
| }; |
| opp-499999992 { |
| opp-hz = /bits/ 64 <499999992>; |
| opp-microvolt = <800000>; |
| }; |
| opp-666666656 { |
| opp-hz = /bits/ 64 <666666656>; |
| opp-microvolt = <800000>; |
| }; |
| opp-799999987 { |
| opp-hz = /bits/ 64 <799999987>; |
| opp-microvolt = <800000>; |
| }; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| /* 3 MiB reserved for ARM Trusted Firmware (BL31) */ |
| secmon_reserved: secmon@5000000 { |
| reg = <0x0 0x05000000 0x0 0x300000>; |
| no-map; |
| }; |
| |
| /* 32 MiB reserved for ARM Trusted Firmware (BL32) */ |
| secmon_reserved_bl32: secmon@5300000 { |
| reg = <0x0 0x05300000 0x0 0x2000000>; |
| no-map; |
| }; |
| |
| linux,cma { |
| compatible = "shared-dma-pool"; |
| reusable; |
| size = <0x0 0x10000000>; |
| alignment = <0x0 0x400000>; |
| linux,cma-default; |
| }; |
| }; |
| |
| sm: secure-monitor { |
| compatible = "amlogic,meson-gxbb-sm"; |
| }; |
| |
| soc { |
| compatible = "simple-bus"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| pcie: pcie@fc000000 { |
| compatible = "amlogic,g12a-pcie", "snps,dw-pcie"; |
| reg = <0x0 0xfc000000 0x0 0x400000>, |
| <0x0 0xff648000 0x0 0x2000>, |
| <0x0 0xfc400000 0x0 0x200000>; |
| reg-names = "elbi", "cfg", "config"; |
| interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &gic GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; |
| bus-range = <0x0 0xff>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| ranges = <0x81000000 0 0 0x0 0xfc600000 0 0x00100000>, |
| <0x82000000 0 0xfc700000 0x0 0xfc700000 0 0x1900000>; |
| |
| clocks = <&clkc CLKID_PCIE_PHY |
| &clkc CLKID_PCIE_COMB |
| &clkc CLKID_PCIE_PLL>; |
| clock-names = "general", |
| "pclk", |
| "port"; |
| resets = <&reset RESET_PCIE_CTRL_A>, |
| <&reset RESET_PCIE_APB>; |
| reset-names = "port", |
| "apb"; |
| num-lanes = <1>; |
| phys = <&usb3_pcie_phy PHY_TYPE_PCIE>; |
| phy-names = "pcie"; |
| status = "disabled"; |
| }; |
| |
| ethmac: ethernet@ff3f0000 { |
| compatible = "amlogic,meson-g12a-dwmac", |
| "snps,dwmac-3.70a", |
| "snps,dwmac"; |
| reg = <0x0 0xff3f0000 0x0 0x10000>, |
| <0x0 0xff634540 0x0 0x8>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq"; |
| clocks = <&clkc CLKID_ETH>, |
| <&clkc CLKID_FCLK_DIV2>, |
| <&clkc CLKID_MPLL2>, |
| <&clkc CLKID_FCLK_DIV2>; |
| clock-names = "stmmaceth", "clkin0", "clkin1", |
| "timing-adjustment"; |
| rx-fifo-depth = <4096>; |
| tx-fifo-depth = <2048>; |
| status = "disabled"; |
| |
| mdio0: mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,dwmac-mdio"; |
| }; |
| }; |
| |
| apb: bus@ff600000 { |
| compatible = "simple-bus"; |
| reg = <0x0 0xff600000 0x0 0x200000>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0x0 0x0 0x0 0xff600000 0x0 0x200000>; |
| |
| hdmi_tx: hdmi-tx@0 { |
| compatible = "amlogic,meson-g12a-dw-hdmi"; |
| reg = <0x0 0x0 0x0 0x10000>; |
| interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>; |
| resets = <&reset RESET_HDMITX_CAPB3>, |
| <&reset RESET_HDMITX_PHY>, |
| <&reset RESET_HDMITX>; |
| reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy"; |
| clocks = <&clkc CLKID_HDMI>, |
| <&clkc CLKID_HTX_PCLK>, |
| <&clkc CLKID_VPU_INTR>; |
| clock-names = "isfr", "iahb", "venci"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #sound-dai-cells = <0>; |
| status = "disabled"; |
| |
| assigned-clocks = <&clkc CLKID_HDMI_SEL>, |
| <&clkc CLKID_HDMI>; |
| assigned-clock-parents = <&xtal>, <0>; |
| assigned-clock-rates = <0>, <24000000>; |
| |
| /* VPU VENC Input */ |
| hdmi_tx_venc_port: port@0 { |
| reg = <0>; |
| |
| hdmi_tx_in: endpoint { |
| remote-endpoint = <&hdmi_tx_out>; |
| }; |
| }; |
| |
| /* TMDS Output */ |
| hdmi_tx_tmds_port: port@1 { |
| reg = <1>; |
| }; |
| }; |
| |
| apb_efuse: bus@30000 { |
| compatible = "simple-bus"; |
| reg = <0x0 0x30000 0x0 0x2000>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0x0 0x0 0x0 0x30000 0x0 0x2000>; |
| |
| hwrng: rng@218 { |
| compatible = "amlogic,meson-rng"; |
| reg = <0x0 0x218 0x0 0x4>; |
| clocks = <&clkc CLKID_RNG0>; |
| clock-names = "core"; |
| }; |
| }; |
| |
| acodec: audio-controller@32000 { |
| compatible = "amlogic,t9015"; |
| reg = <0x0 0x32000 0x0 0x14>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "ACODEC"; |
| clocks = <&clkc CLKID_AUDIO_CODEC>; |
| clock-names = "pclk"; |
| resets = <&reset RESET_AUDIO_CODEC>; |
| status = "disabled"; |
| }; |
| |
| periphs: bus@34400 { |
| compatible = "simple-bus"; |
| reg = <0x0 0x34400 0x0 0x400>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0x0 0x0 0x0 0x34400 0x0 0x400>; |
| |
| periphs_pinctrl: pinctrl@40 { |
| compatible = "amlogic,meson-g12a-periphs-pinctrl"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| gpio: bank@40 { |
| reg = <0x0 0x40 0x0 0x4c>, |
| <0x0 0xe8 0x0 0x18>, |
| <0x0 0x120 0x0 0x18>, |
| <0x0 0x2c0 0x0 0x40>, |
| <0x0 0x340 0x0 0x1c>; |
| reg-names = "gpio", |
| "pull", |
| "pull-enable", |
| "mux", |
| "ds"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&periphs_pinctrl 0 0 86>; |
| }; |
| |
| cec_ao_a_h_pins: cec_ao_a_h { |
| mux { |
| groups = "cec_ao_a_h"; |
| function = "cec_ao_a_h"; |
| bias-disable; |
| }; |
| }; |
| |
| cec_ao_b_h_pins: cec_ao_b_h { |
| mux { |
| groups = "cec_ao_b_h"; |
| function = "cec_ao_b_h"; |
| bias-disable; |
| }; |
| }; |
| |
| emmc_ctrl_pins: emmc-ctrl { |
| mux-0 { |
| groups = "emmc_cmd"; |
| function = "emmc"; |
| bias-pull-up; |
| drive-strength-microamp = <4000>; |
| }; |
| |
| mux-1 { |
| groups = "emmc_clk"; |
| function = "emmc"; |
| bias-disable; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| emmc_data_4b_pins: emmc-data-4b { |
| mux-0 { |
| groups = "emmc_nand_d0", |
| "emmc_nand_d1", |
| "emmc_nand_d2", |
| "emmc_nand_d3"; |
| function = "emmc"; |
| bias-pull-up; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| emmc_data_8b_pins: emmc-data-8b { |
| mux-0 { |
| groups = "emmc_nand_d0", |
| "emmc_nand_d1", |
| "emmc_nand_d2", |
| "emmc_nand_d3", |
| "emmc_nand_d4", |
| "emmc_nand_d5", |
| "emmc_nand_d6", |
| "emmc_nand_d7"; |
| function = "emmc"; |
| bias-pull-up; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| emmc_ds_pins: emmc-ds { |
| mux { |
| groups = "emmc_nand_ds"; |
| function = "emmc"; |
| bias-pull-down; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| emmc_clk_gate_pins: emmc_clk_gate { |
| mux { |
| groups = "BOOT_8"; |
| function = "gpio_periphs"; |
| bias-pull-down; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| hdmitx_ddc_pins: hdmitx_ddc { |
| mux { |
| groups = "hdmitx_sda", |
| "hdmitx_sck"; |
| function = "hdmitx"; |
| bias-disable; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| hdmitx_hpd_pins: hdmitx_hpd { |
| mux { |
| groups = "hdmitx_hpd_in"; |
| function = "hdmitx"; |
| bias-disable; |
| }; |
| }; |
| |
| |
| i2c0_sda_c_pins: i2c0-sda-c { |
| mux { |
| groups = "i2c0_sda_c"; |
| function = "i2c0"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| |
| }; |
| }; |
| |
| i2c0_sck_c_pins: i2c0-sck-c { |
| mux { |
| groups = "i2c0_sck_c"; |
| function = "i2c0"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c0_sda_z0_pins: i2c0-sda-z0 { |
| mux { |
| groups = "i2c0_sda_z0"; |
| function = "i2c0"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c0_sck_z1_pins: i2c0-sck-z1 { |
| mux { |
| groups = "i2c0_sck_z1"; |
| function = "i2c0"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c0_sda_z7_pins: i2c0-sda-z7 { |
| mux { |
| groups = "i2c0_sda_z7"; |
| function = "i2c0"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c0_sda_z8_pins: i2c0-sda-z8 { |
| mux { |
| groups = "i2c0_sda_z8"; |
| function = "i2c0"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c1_sda_x_pins: i2c1-sda-x { |
| mux { |
| groups = "i2c1_sda_x"; |
| function = "i2c1"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c1_sck_x_pins: i2c1-sck-x { |
| mux { |
| groups = "i2c1_sck_x"; |
| function = "i2c1"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c1_sda_h2_pins: i2c1-sda-h2 { |
| mux { |
| groups = "i2c1_sda_h2"; |
| function = "i2c1"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c1_sck_h3_pins: i2c1-sck-h3 { |
| mux { |
| groups = "i2c1_sck_h3"; |
| function = "i2c1"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c1_sda_h6_pins: i2c1-sda-h6 { |
| mux { |
| groups = "i2c1_sda_h6"; |
| function = "i2c1"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c1_sck_h7_pins: i2c1-sck-h7 { |
| mux { |
| groups = "i2c1_sck_h7"; |
| function = "i2c1"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c2_sda_x_pins: i2c2-sda-x { |
| mux { |
| groups = "i2c2_sda_x"; |
| function = "i2c2"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c2_sck_x_pins: i2c2-sck-x { |
| mux { |
| groups = "i2c2_sck_x"; |
| function = "i2c2"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c2_sda_z_pins: i2c2-sda-z { |
| mux { |
| groups = "i2c2_sda_z"; |
| function = "i2c2"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c2_sck_z_pins: i2c2-sck-z { |
| mux { |
| groups = "i2c2_sck_z"; |
| function = "i2c2"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c3_sda_h_pins: i2c3-sda-h { |
| mux { |
| groups = "i2c3_sda_h"; |
| function = "i2c3"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c3_sck_h_pins: i2c3-sck-h { |
| mux { |
| groups = "i2c3_sck_h"; |
| function = "i2c3"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c3_sda_a_pins: i2c3-sda-a { |
| mux { |
| groups = "i2c3_sda_a"; |
| function = "i2c3"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c3_sck_a_pins: i2c3-sck-a { |
| mux { |
| groups = "i2c3_sck_a"; |
| function = "i2c3"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| mclk0_a_pins: mclk0-a { |
| mux { |
| groups = "mclk0_a"; |
| function = "mclk0"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| mclk1_a_pins: mclk1-a { |
| mux { |
| groups = "mclk1_a"; |
| function = "mclk1"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| mclk1_x_pins: mclk1-x { |
| mux { |
| groups = "mclk1_x"; |
| function = "mclk1"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| mclk1_z_pins: mclk1-z { |
| mux { |
| groups = "mclk1_z"; |
| function = "mclk1"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| nor_pins: nor { |
| mux { |
| groups = "nor_d", |
| "nor_q", |
| "nor_c", |
| "nor_cs"; |
| function = "nor"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din0_a_pins: pdm-din0-a { |
| mux { |
| groups = "pdm_din0_a"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din0_c_pins: pdm-din0-c { |
| mux { |
| groups = "pdm_din0_c"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din0_x_pins: pdm-din0-x { |
| mux { |
| groups = "pdm_din0_x"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din0_z_pins: pdm-din0-z { |
| mux { |
| groups = "pdm_din0_z"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din1_a_pins: pdm-din1-a { |
| mux { |
| groups = "pdm_din1_a"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din1_c_pins: pdm-din1-c { |
| mux { |
| groups = "pdm_din1_c"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din1_x_pins: pdm-din1-x { |
| mux { |
| groups = "pdm_din1_x"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din1_z_pins: pdm-din1-z { |
| mux { |
| groups = "pdm_din1_z"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din2_a_pins: pdm-din2-a { |
| mux { |
| groups = "pdm_din2_a"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din2_c_pins: pdm-din2-c { |
| mux { |
| groups = "pdm_din2_c"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din2_x_pins: pdm-din2-x { |
| mux { |
| groups = "pdm_din2_x"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din2_z_pins: pdm-din2-z { |
| mux { |
| groups = "pdm_din2_z"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din3_a_pins: pdm-din3-a { |
| mux { |
| groups = "pdm_din3_a"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din3_c_pins: pdm-din3-c { |
| mux { |
| groups = "pdm_din3_c"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din3_x_pins: pdm-din3-x { |
| mux { |
| groups = "pdm_din3_x"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_din3_z_pins: pdm-din3-z { |
| mux { |
| groups = "pdm_din3_z"; |
| function = "pdm"; |
| bias-disable; |
| }; |
| }; |
| |
| pdm_dclk_a_pins: pdm-dclk-a { |
| mux { |
| groups = "pdm_dclk_a"; |
| function = "pdm"; |
| bias-disable; |
| drive-strength-microamp = <500>; |
| }; |
| }; |
| |
| pdm_dclk_c_pins: pdm-dclk-c { |
| mux { |
| groups = "pdm_dclk_c"; |
| function = "pdm"; |
| bias-disable; |
| drive-strength-microamp = <500>; |
| }; |
| }; |
| |
| pdm_dclk_x_pins: pdm-dclk-x { |
| mux { |
| groups = "pdm_dclk_x"; |
| function = "pdm"; |
| bias-disable; |
| drive-strength-microamp = <500>; |
| }; |
| }; |
| |
| pdm_dclk_z_pins: pdm-dclk-z { |
| mux { |
| groups = "pdm_dclk_z"; |
| function = "pdm"; |
| bias-disable; |
| drive-strength-microamp = <500>; |
| }; |
| }; |
| |
| pwm_a_pins: pwm-a { |
| mux { |
| groups = "pwm_a"; |
| function = "pwm_a"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_b_x7_pins: pwm-b-x7 { |
| mux { |
| groups = "pwm_b_x7"; |
| function = "pwm_b"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_b_x19_pins: pwm-b-x19 { |
| mux { |
| groups = "pwm_b_x19"; |
| function = "pwm_b"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_c_c_pins: pwm-c-c { |
| mux { |
| groups = "pwm_c_c"; |
| function = "pwm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_c_x5_pins: pwm-c-x5 { |
| mux { |
| groups = "pwm_c_x5"; |
| function = "pwm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_c_x8_pins: pwm-c-x8 { |
| mux { |
| groups = "pwm_c_x8"; |
| function = "pwm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_d_x3_pins: pwm-d-x3 { |
| mux { |
| groups = "pwm_d_x3"; |
| function = "pwm_d"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_d_x6_pins: pwm-d-x6 { |
| mux { |
| groups = "pwm_d_x6"; |
| function = "pwm_d"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_e_pins: pwm-e { |
| mux { |
| groups = "pwm_e"; |
| function = "pwm_e"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_f_z_pins: pwm-f-z { |
| mux { |
| groups = "pwm_f_z"; |
| function = "pwm_f"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_f_a_pins: pwm-f-a { |
| mux { |
| groups = "pwm_f_a"; |
| function = "pwm_f"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_f_x_pins: pwm-f-x { |
| mux { |
| groups = "pwm_f_x"; |
| function = "pwm_f"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_f_h_pins: pwm-f-h { |
| mux { |
| groups = "pwm_f_h"; |
| function = "pwm_f"; |
| bias-disable; |
| }; |
| }; |
| |
| sdcard_c_pins: sdcard_c { |
| mux-0 { |
| groups = "sdcard_d0_c", |
| "sdcard_d1_c", |
| "sdcard_d2_c", |
| "sdcard_d3_c", |
| "sdcard_cmd_c"; |
| function = "sdcard"; |
| bias-pull-up; |
| drive-strength-microamp = <4000>; |
| }; |
| |
| mux-1 { |
| groups = "sdcard_clk_c"; |
| function = "sdcard"; |
| bias-disable; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| sdcard_clk_gate_c_pins: sdcard_clk_gate_c { |
| mux { |
| groups = "GPIOC_4"; |
| function = "gpio_periphs"; |
| bias-pull-down; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| sdcard_z_pins: sdcard_z { |
| mux-0 { |
| groups = "sdcard_d0_z", |
| "sdcard_d1_z", |
| "sdcard_d2_z", |
| "sdcard_d3_z", |
| "sdcard_cmd_z"; |
| function = "sdcard"; |
| bias-pull-up; |
| drive-strength-microamp = <4000>; |
| }; |
| |
| mux-1 { |
| groups = "sdcard_clk_z"; |
| function = "sdcard"; |
| bias-disable; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| sdcard_clk_gate_z_pins: sdcard_clk_gate_z { |
| mux { |
| groups = "GPIOZ_6"; |
| function = "gpio_periphs"; |
| bias-pull-down; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| sdio_pins: sdio { |
| mux { |
| groups = "sdio_d0", |
| "sdio_d1", |
| "sdio_d2", |
| "sdio_d3", |
| "sdio_clk", |
| "sdio_cmd"; |
| function = "sdio"; |
| bias-disable; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| sdio_clk_gate_pins: sdio_clk_gate { |
| mux { |
| groups = "GPIOX_4"; |
| function = "gpio_periphs"; |
| bias-pull-down; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| spdif_in_a10_pins: spdif-in-a10 { |
| mux { |
| groups = "spdif_in_a10"; |
| function = "spdif_in"; |
| bias-disable; |
| }; |
| }; |
| |
| spdif_in_a12_pins: spdif-in-a12 { |
| mux { |
| groups = "spdif_in_a12"; |
| function = "spdif_in"; |
| bias-disable; |
| }; |
| }; |
| |
| spdif_in_h_pins: spdif-in-h { |
| mux { |
| groups = "spdif_in_h"; |
| function = "spdif_in"; |
| bias-disable; |
| }; |
| }; |
| |
| spdif_out_h_pins: spdif-out-h { |
| mux { |
| groups = "spdif_out_h"; |
| function = "spdif_out"; |
| drive-strength-microamp = <3000>; |
| bias-disable; |
| }; |
| }; |
| |
| spdif_out_a11_pins: spdif-out-a11 { |
| mux { |
| groups = "spdif_out_a11"; |
| function = "spdif_out"; |
| drive-strength-microamp = <3000>; |
| bias-disable; |
| }; |
| }; |
| |
| spdif_out_a13_pins: spdif-out-a13 { |
| mux { |
| groups = "spdif_out_a13"; |
| function = "spdif_out"; |
| drive-strength-microamp = <3000>; |
| bias-disable; |
| }; |
| }; |
| |
| spicc0_x_pins: spicc0-x { |
| mux { |
| groups = "spi0_mosi_x", |
| "spi0_miso_x", |
| "spi0_clk_x"; |
| function = "spi0"; |
| drive-strength-microamp = <4000>; |
| bias-disable; |
| }; |
| }; |
| |
| spicc0_ss0_x_pins: spicc0-ss0-x { |
| mux { |
| groups = "spi0_ss0_x"; |
| function = "spi0"; |
| drive-strength-microamp = <4000>; |
| bias-disable; |
| }; |
| }; |
| |
| spicc0_c_pins: spicc0-c { |
| mux { |
| groups = "spi0_mosi_c", |
| "spi0_miso_c", |
| "spi0_ss0_c", |
| "spi0_clk_c"; |
| function = "spi0"; |
| drive-strength-microamp = <4000>; |
| bias-disable; |
| }; |
| }; |
| |
| spicc1_pins: spicc1 { |
| mux { |
| groups = "spi1_mosi", |
| "spi1_miso", |
| "spi1_clk"; |
| function = "spi1"; |
| drive-strength-microamp = <4000>; |
| }; |
| }; |
| |
| spicc1_ss0_pins: spicc1-ss0 { |
| mux { |
| groups = "spi1_ss0"; |
| function = "spi1"; |
| drive-strength-microamp = <4000>; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_a_din0_pins: tdm-a-din0 { |
| mux { |
| groups = "tdm_a_din0"; |
| function = "tdm_a"; |
| bias-disable; |
| }; |
| }; |
| |
| |
| tdm_a_din1_pins: tdm-a-din1 { |
| mux { |
| groups = "tdm_a_din1"; |
| function = "tdm_a"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_a_dout0_pins: tdm-a-dout0 { |
| mux { |
| groups = "tdm_a_dout0"; |
| function = "tdm_a"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_a_dout1_pins: tdm-a-dout1 { |
| mux { |
| groups = "tdm_a_dout1"; |
| function = "tdm_a"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_a_fs_pins: tdm-a-fs { |
| mux { |
| groups = "tdm_a_fs"; |
| function = "tdm_a"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_a_sclk_pins: tdm-a-sclk { |
| mux { |
| groups = "tdm_a_sclk"; |
| function = "tdm_a"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_a_slv_fs_pins: tdm-a-slv-fs { |
| mux { |
| groups = "tdm_a_slv_fs"; |
| function = "tdm_a"; |
| bias-disable; |
| }; |
| }; |
| |
| |
| tdm_a_slv_sclk_pins: tdm-a-slv-sclk { |
| mux { |
| groups = "tdm_a_slv_sclk"; |
| function = "tdm_a"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_b_din0_pins: tdm-b-din0 { |
| mux { |
| groups = "tdm_b_din0"; |
| function = "tdm_b"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_b_din1_pins: tdm-b-din1 { |
| mux { |
| groups = "tdm_b_din1"; |
| function = "tdm_b"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_b_din2_pins: tdm-b-din2 { |
| mux { |
| groups = "tdm_b_din2"; |
| function = "tdm_b"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_b_din3_a_pins: tdm-b-din3-a { |
| mux { |
| groups = "tdm_b_din3_a"; |
| function = "tdm_b"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_b_din3_h_pins: tdm-b-din3-h { |
| mux { |
| groups = "tdm_b_din3_h"; |
| function = "tdm_b"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_b_dout0_pins: tdm-b-dout0 { |
| mux { |
| groups = "tdm_b_dout0"; |
| function = "tdm_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_b_dout1_pins: tdm-b-dout1 { |
| mux { |
| groups = "tdm_b_dout1"; |
| function = "tdm_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_b_dout2_pins: tdm-b-dout2 { |
| mux { |
| groups = "tdm_b_dout2"; |
| function = "tdm_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_b_dout3_a_pins: tdm-b-dout3-a { |
| mux { |
| groups = "tdm_b_dout3_a"; |
| function = "tdm_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_b_dout3_h_pins: tdm-b-dout3-h { |
| mux { |
| groups = "tdm_b_dout3_h"; |
| function = "tdm_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_b_fs_pins: tdm-b-fs { |
| mux { |
| groups = "tdm_b_fs"; |
| function = "tdm_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_b_sclk_pins: tdm-b-sclk { |
| mux { |
| groups = "tdm_b_sclk"; |
| function = "tdm_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_b_slv_fs_pins: tdm-b-slv-fs { |
| mux { |
| groups = "tdm_b_slv_fs"; |
| function = "tdm_b"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_b_slv_sclk_pins: tdm-b-slv-sclk { |
| mux { |
| groups = "tdm_b_slv_sclk"; |
| function = "tdm_b"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_din0_a_pins: tdm-c-din0-a { |
| mux { |
| groups = "tdm_c_din0_a"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_din0_z_pins: tdm-c-din0-z { |
| mux { |
| groups = "tdm_c_din0_z"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_din1_a_pins: tdm-c-din1-a { |
| mux { |
| groups = "tdm_c_din1_a"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_din1_z_pins: tdm-c-din1-z { |
| mux { |
| groups = "tdm_c_din1_z"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_din2_a_pins: tdm-c-din2-a { |
| mux { |
| groups = "tdm_c_din2_a"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| eth_leds_pins: eth-leds { |
| mux { |
| groups = "eth_link_led", |
| "eth_act_led"; |
| function = "eth"; |
| bias-disable; |
| }; |
| }; |
| |
| eth_pins: eth { |
| mux { |
| groups = "eth_mdio", |
| "eth_mdc", |
| "eth_rgmii_rx_clk", |
| "eth_rx_dv", |
| "eth_rxd0", |
| "eth_rxd1", |
| "eth_txen", |
| "eth_txd0", |
| "eth_txd1"; |
| function = "eth"; |
| drive-strength-microamp = <4000>; |
| bias-disable; |
| }; |
| }; |
| |
| eth_rgmii_pins: eth-rgmii { |
| mux { |
| groups = "eth_rxd2_rgmii", |
| "eth_rxd3_rgmii", |
| "eth_rgmii_tx_clk", |
| "eth_txd2_rgmii", |
| "eth_txd3_rgmii"; |
| function = "eth"; |
| drive-strength-microamp = <4000>; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_din2_z_pins: tdm-c-din2-z { |
| mux { |
| groups = "tdm_c_din2_z"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_din3_a_pins: tdm-c-din3-a { |
| mux { |
| groups = "tdm_c_din3_a"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_din3_z_pins: tdm-c-din3-z { |
| mux { |
| groups = "tdm_c_din3_z"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_dout0_a_pins: tdm-c-dout0-a { |
| mux { |
| groups = "tdm_c_dout0_a"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_dout0_z_pins: tdm-c-dout0-z { |
| mux { |
| groups = "tdm_c_dout0_z"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_dout1_a_pins: tdm-c-dout1-a { |
| mux { |
| groups = "tdm_c_dout1_a"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_dout1_z_pins: tdm-c-dout1-z { |
| mux { |
| groups = "tdm_c_dout1_z"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_dout2_a_pins: tdm-c-dout2-a { |
| mux { |
| groups = "tdm_c_dout2_a"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_dout2_z_pins: tdm-c-dout2-z { |
| mux { |
| groups = "tdm_c_dout2_z"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_dout3_a_pins: tdm-c-dout3-a { |
| mux { |
| groups = "tdm_c_dout3_a"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_dout3_z_pins: tdm-c-dout3-z { |
| mux { |
| groups = "tdm_c_dout3_z"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_fs_a_pins: tdm-c-fs-a { |
| mux { |
| groups = "tdm_c_fs_a"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_fs_z_pins: tdm-c-fs-z { |
| mux { |
| groups = "tdm_c_fs_z"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_sclk_a_pins: tdm-c-sclk-a { |
| mux { |
| groups = "tdm_c_sclk_a"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_sclk_z_pins: tdm-c-sclk-z { |
| mux { |
| groups = "tdm_c_sclk_z"; |
| function = "tdm_c"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_c_slv_fs_a_pins: tdm-c-slv-fs-a { |
| mux { |
| groups = "tdm_c_slv_fs_a"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_slv_fs_z_pins: tdm-c-slv-fs-z { |
| mux { |
| groups = "tdm_c_slv_fs_z"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_slv_sclk_a_pins: tdm-c-slv-sclk-a { |
| mux { |
| groups = "tdm_c_slv_sclk_a"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_c_slv_sclk_z_pins: tdm-c-slv-sclk-z { |
| mux { |
| groups = "tdm_c_slv_sclk_z"; |
| function = "tdm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_a_pins: uart-a { |
| mux { |
| groups = "uart_a_tx", |
| "uart_a_rx"; |
| function = "uart_a"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_a_cts_rts_pins: uart-a-cts-rts { |
| mux { |
| groups = "uart_a_cts", |
| "uart_a_rts"; |
| function = "uart_a"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_b_pins: uart-b { |
| mux { |
| groups = "uart_b_tx", |
| "uart_b_rx"; |
| function = "uart_b"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_c_pins: uart-c { |
| mux { |
| groups = "uart_c_tx", |
| "uart_c_rx"; |
| function = "uart_c"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_c_cts_rts_pins: uart-c-cts-rts { |
| mux { |
| groups = "uart_c_cts", |
| "uart_c_rts"; |
| function = "uart_c"; |
| bias-disable; |
| }; |
| }; |
| }; |
| }; |
| |
| cpu_temp: temperature-sensor@34800 { |
| compatible = "amlogic,g12a-cpu-thermal", |
| "amlogic,g12a-thermal"; |
| reg = <0x0 0x34800 0x0 0x50>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&clkc CLKID_TS>; |
| #thermal-sensor-cells = <0>; |
| amlogic,ao-secure = <&sec_AO>; |
| }; |
| |
| ddr_temp: temperature-sensor@34c00 { |
| compatible = "amlogic,g12a-ddr-thermal", |
| "amlogic,g12a-thermal"; |
| reg = <0x0 0x34c00 0x0 0x50>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&clkc CLKID_TS>; |
| #thermal-sensor-cells = <0>; |
| amlogic,ao-secure = <&sec_AO>; |
| }; |
| |
| usb2_phy0: phy@36000 { |
| compatible = "amlogic,g12a-usb2-phy"; |
| reg = <0x0 0x36000 0x0 0x2000>; |
| clocks = <&xtal>; |
| clock-names = "xtal"; |
| resets = <&reset RESET_USB_PHY20>; |
| reset-names = "phy"; |
| #phy-cells = <0>; |
| }; |
| |
| dmc: bus@38000 { |
| compatible = "simple-bus"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0x0 0x0 0x0 0x38000 0x0 0x2000>; |
| |
| canvas: video-lut@48 { |
| compatible = "amlogic,canvas"; |
| reg = <0x0 0x48 0x0 0x14>; |
| }; |
| |
| pmu: pmu@80 { |
| reg = <0x0 0x80 0x0 0x40>, |
| <0x0 0xc00 0x0 0x40>; |
| interrupts = <GIC_SPI 52 IRQ_TYPE_EDGE_RISING>; |
| }; |
| }; |
| |
| usb2_phy1: phy@3a000 { |
| compatible = "amlogic,g12a-usb2-phy"; |
| reg = <0x0 0x3a000 0x0 0x2000>; |
| clocks = <&xtal>; |
| clock-names = "xtal"; |
| resets = <&reset RESET_USB_PHY21>; |
| reset-names = "phy"; |
| #phy-cells = <0>; |
| }; |
| |
| hiu: bus@3c000 { |
| compatible = "simple-bus"; |
| reg = <0x0 0x3c000 0x0 0x1400>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0x0 0x0 0x0 0x3c000 0x0 0x1400>; |
| |
| hhi: system-controller@0 { |
| compatible = "amlogic,meson-gx-hhi-sysctrl", |
| "simple-mfd", "syscon"; |
| reg = <0 0 0 0x400>; |
| |
| clkc: clock-controller { |
| compatible = "amlogic,g12a-clkc"; |
| #clock-cells = <1>; |
| clocks = <&xtal>; |
| clock-names = "xtal"; |
| }; |
| |
| pwrc: power-controller { |
| compatible = "amlogic,meson-g12a-pwrc"; |
| #power-domain-cells = <1>; |
| amlogic,ao-sysctrl = <&rti>; |
| resets = <&reset RESET_VIU>, |
| <&reset RESET_VENC>, |
| <&reset RESET_VCBUS>, |
| <&reset RESET_BT656>, |
| <&reset RESET_RDMA>, |
| <&reset RESET_VENCI>, |
| <&reset RESET_VENCP>, |
| <&reset RESET_VDAC>, |
| <&reset RESET_VDI6>, |
| <&reset RESET_VENCL>, |
| <&reset RESET_VID_LOCK>; |
| reset-names = "viu", "venc", "vcbus", "bt656", |
| "rdma", "venci", "vencp", "vdac", |
| "vdi6", "vencl", "vid_lock"; |
| clocks = <&clkc CLKID_VPU>, |
| <&clkc CLKID_VAPB>; |
| clock-names = "vpu", "vapb"; |
| /* |
| * VPU clocking is provided by two identical clock paths |
| * VPU_0 and VPU_1 muxed to a single clock by a glitch |
| * free mux to safely change frequency while running. |
| * Same for VAPB but with a final gate after the glitch free mux. |
| */ |
| assigned-clocks = <&clkc CLKID_VPU_0_SEL>, |
| <&clkc CLKID_VPU_0>, |
| <&clkc CLKID_VPU>, /* Glitch free mux */ |
| <&clkc CLKID_VAPB_0_SEL>, |
| <&clkc CLKID_VAPB_0>, |
| <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */ |
| assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>, |
| <0>, /* Do Nothing */ |
| <&clkc CLKID_VPU_0>, |
| <&clkc CLKID_FCLK_DIV4>, |
| <0>, /* Do Nothing */ |
| <&clkc CLKID_VAPB_0>; |
| assigned-clock-rates = <0>, /* Do Nothing */ |
| <666666666>, |
| <0>, /* Do Nothing */ |
| <0>, /* Do Nothing */ |
| <250000000>, |
| <0>; /* Do Nothing */ |
| }; |
| |
| mipi_analog_dphy: phy { |
| compatible = "amlogic,g12a-mipi-dphy-analog"; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| mipi_dphy: phy@44000 { |
| compatible = "amlogic,axg-mipi-dphy"; |
| reg = <0x0 0x44000 0x0 0x2000>; |
| clocks = <&clkc CLKID_MIPI_DSI_PHY>; |
| clock-names = "pclk"; |
| resets = <&reset RESET_MIPI_DSI_PHY>; |
| reset-names = "phy"; |
| phys = <&mipi_analog_dphy>; |
| phy-names = "analog"; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| usb3_pcie_phy: phy@46000 { |
| compatible = "amlogic,g12a-usb3-pcie-phy"; |
| reg = <0x0 0x46000 0x0 0x2000>; |
| clocks = <&clkc CLKID_PCIE_PLL>; |
| clock-names = "ref_clk"; |
| resets = <&reset RESET_PCIE_PHY>; |
| reset-names = "phy"; |
| assigned-clocks = <&clkc CLKID_PCIE_PLL>; |
| assigned-clock-rates = <100000000>; |
| #phy-cells = <1>; |
| }; |
| |
| eth_phy: mdio-multiplexer@4c000 { |
| compatible = "amlogic,g12a-mdio-mux"; |
| reg = <0x0 0x4c000 0x0 0xa4>; |
| clocks = <&clkc CLKID_ETH_PHY>, |
| <&xtal>, |
| <&clkc CLKID_MPLL_50M>; |
| clock-names = "pclk", "clkin0", "clkin1"; |
| mdio-parent-bus = <&mdio0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ext_mdio: mdio@0 { |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| int_mdio: mdio@1 { |
| reg = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| internal_ephy: ethernet-phy@8 { |
| compatible = "ethernet-phy-id0180.3301", |
| "ethernet-phy-ieee802.3-c22"; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <8>; |
| max-speed = <100>; |
| }; |
| }; |
| }; |
| }; |
| |
| aobus: bus@ff800000 { |
| compatible = "simple-bus"; |
| reg = <0x0 0xff800000 0x0 0x100000>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0x0 0x0 0x0 0xff800000 0x0 0x100000>; |
| |
| rti: sys-ctrl@0 { |
| compatible = "amlogic,meson-gx-ao-sysctrl", |
| "simple-mfd", "syscon"; |
| reg = <0x0 0x0 0x0 0x100>; |
| |
| clkc_AO: clock-controller { |
| compatible = "amlogic,meson-g12a-aoclkc"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| clocks = <&xtal>, <&clkc CLKID_CLK81>; |
| clock-names = "xtal", "mpeg-clk"; |
| }; |
| }; |
| |
| ao_pinctrl: pinctrl@14 { |
| compatible = "amlogic,meson-g12a-aobus-pinctrl"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| gpio_ao: bank@14 { |
| reg = <0x0 0x14 0x0 0x8>, |
| <0x0 0x1c 0x0 0x8>, |
| <0x0 0x24 0x0 0x14>; |
| reg-names = "mux", |
| "ds", |
| "gpio"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&ao_pinctrl 0 0 15>; |
| }; |
| |
| i2c_ao_sck_pins: i2c_ao_sck_pins { |
| mux { |
| groups = "i2c_ao_sck"; |
| function = "i2c_ao"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c_ao_sda_pins: i2c_ao_sda { |
| mux { |
| groups = "i2c_ao_sda"; |
| function = "i2c_ao"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c_ao_sck_e_pins: i2c_ao_sck_e { |
| mux { |
| groups = "i2c_ao_sck_e"; |
| function = "i2c_ao"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| i2c_ao_sda_e_pins: i2c_ao_sda_e { |
| mux { |
| groups = "i2c_ao_sda_e"; |
| function = "i2c_ao"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| mclk0_ao_pins: mclk0-ao { |
| mux { |
| groups = "mclk0_ao"; |
| function = "mclk0_ao"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_ao_b_din0_pins: tdm-ao-b-din0 { |
| mux { |
| groups = "tdm_ao_b_din0"; |
| function = "tdm_ao_b"; |
| bias-disable; |
| }; |
| }; |
| |
| spdif_ao_out_pins: spdif-ao-out { |
| mux { |
| groups = "spdif_ao_out"; |
| function = "spdif_ao_out"; |
| drive-strength-microamp = <3000>; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_ao_b_din1_pins: tdm-ao-b-din1 { |
| mux { |
| groups = "tdm_ao_b_din1"; |
| function = "tdm_ao_b"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_ao_b_din2_pins: tdm-ao-b-din2 { |
| mux { |
| groups = "tdm_ao_b_din2"; |
| function = "tdm_ao_b"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_ao_b_dout0_pins: tdm-ao-b-dout0 { |
| mux { |
| groups = "tdm_ao_b_dout0"; |
| function = "tdm_ao_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_ao_b_dout1_pins: tdm-ao-b-dout1 { |
| mux { |
| groups = "tdm_ao_b_dout1"; |
| function = "tdm_ao_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_ao_b_dout2_pins: tdm-ao-b-dout2 { |
| mux { |
| groups = "tdm_ao_b_dout2"; |
| function = "tdm_ao_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_ao_b_fs_pins: tdm-ao-b-fs { |
| mux { |
| groups = "tdm_ao_b_fs"; |
| function = "tdm_ao_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_ao_b_sclk_pins: tdm-ao-b-sclk { |
| mux { |
| groups = "tdm_ao_b_sclk"; |
| function = "tdm_ao_b"; |
| bias-disable; |
| drive-strength-microamp = <3000>; |
| }; |
| }; |
| |
| tdm_ao_b_slv_fs_pins: tdm-ao-b-slv-fs { |
| mux { |
| groups = "tdm_ao_b_slv_fs"; |
| function = "tdm_ao_b"; |
| bias-disable; |
| }; |
| }; |
| |
| tdm_ao_b_slv_sclk_pins: tdm-ao-b-slv-sclk { |
| mux { |
| groups = "tdm_ao_b_slv_sclk"; |
| function = "tdm_ao_b"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_ao_a_pins: uart-a-ao { |
| mux { |
| groups = "uart_ao_a_tx", |
| "uart_ao_a_rx"; |
| function = "uart_ao_a"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_ao_a_cts_rts_pins: uart-ao-a-cts-rts { |
| mux { |
| groups = "uart_ao_a_cts", |
| "uart_ao_a_rts"; |
| function = "uart_ao_a"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_ao_b_2_3_pins: uart-ao-b-2-3 { |
| mux { |
| groups = "uart_ao_b_tx_2", |
| "uart_ao_b_rx_3"; |
| function = "uart_ao_b"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_ao_b_8_9_pins: uart-ao-b-8-9 { |
| mux { |
| groups = "uart_ao_b_tx_8", |
| "uart_ao_b_rx_9"; |
| function = "uart_ao_b"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_ao_b_cts_rts_pins: uart-ao-b-cts-rts { |
| mux { |
| groups = "uart_ao_b_cts", |
| "uart_ao_b_rts"; |
| function = "uart_ao_b"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_a_e_pins: pwm-a-e { |
| mux { |
| groups = "pwm_a_e"; |
| function = "pwm_a_e"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_ao_a_pins: pwm-ao-a { |
| mux { |
| groups = "pwm_ao_a"; |
| function = "pwm_ao_a"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_ao_b_pins: pwm-ao-b { |
| mux { |
| groups = "pwm_ao_b"; |
| function = "pwm_ao_b"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_ao_c_4_pins: pwm-ao-c-4 { |
| mux { |
| groups = "pwm_ao_c_4"; |
| function = "pwm_ao_c"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_ao_c_6_pins: pwm-ao-c-6 { |
| mux { |
| groups = "pwm_ao_c_6"; |
| function = "pwm_ao_c"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_ao_d_5_pins: pwm-ao-d-5 { |
| mux { |
| groups = "pwm_ao_d_5"; |
| function = "pwm_ao_d"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_ao_d_10_pins: pwm-ao-d-10 { |
| mux { |
| groups = "pwm_ao_d_10"; |
| function = "pwm_ao_d"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_ao_d_e_pins: pwm-ao-d-e { |
| mux { |
| groups = "pwm_ao_d_e"; |
| function = "pwm_ao_d"; |
| }; |
| }; |
| |
| remote_input_ao_pins: remote-input-ao { |
| mux { |
| groups = "remote_ao_input"; |
| function = "remote_ao_input"; |
| bias-disable; |
| }; |
| }; |
| }; |
| |
| vrtc: rtc@a8 { |
| compatible = "amlogic,meson-vrtc"; |
| reg = <0x0 0x000a8 0x0 0x4>; |
| }; |
| |
| cec_AO: cec@100 { |
| compatible = "amlogic,meson-gx-ao-cec"; |
| reg = <0x0 0x00100 0x0 0x14>; |
| interrupts = <GIC_SPI 199 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&clkc_AO CLKID_AO_CEC>; |
| clock-names = "core"; |
| status = "disabled"; |
| }; |
| |
| sec_AO: ao-secure@140 { |
| compatible = "amlogic,meson-gx-ao-secure", "syscon"; |
| reg = <0x0 0x140 0x0 0x140>; |
| amlogic,has-chip-id; |
| }; |
| |
| cecb_AO: cec@280 { |
| compatible = "amlogic,meson-g12a-ao-cec"; |
| reg = <0x0 0x00280 0x0 0x1c>; |
| interrupts = <GIC_SPI 203 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&clkc_AO CLKID_AO_CTS_OSCIN>; |
| clock-names = "oscin"; |
| status = "disabled"; |
| }; |
| |
| pwm_AO_cd: pwm@2000 { |
| compatible = "amlogic,meson-g12a-ao-pwm-cd"; |
| reg = <0x0 0x2000 0x0 0x20>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| uart_AO: serial@3000 { |
| compatible = "amlogic,meson-g12a-uart", |
| "amlogic,meson-gx-uart", |
| "amlogic,meson-ao-uart"; |
| reg = <0x0 0x3000 0x0 0x18>; |
| interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&xtal>, <&clkc_AO CLKID_AO_UART>, <&xtal>; |
| clock-names = "xtal", "pclk", "baud"; |
| status = "disabled"; |
| }; |
| |
| uart_AO_B: serial@4000 { |
| compatible = "amlogic,meson-g12a-uart", |
| "amlogic,meson-gx-uart", |
| "amlogic,meson-ao-uart"; |
| reg = <0x0 0x4000 0x0 0x18>; |
| interrupts = <GIC_SPI 197 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&xtal>, <&clkc_AO CLKID_AO_UART2>, <&xtal>; |
| clock-names = "xtal", "pclk", "baud"; |
| status = "disabled"; |
| }; |
| |
| i2c_AO: i2c@5000 { |
| compatible = "amlogic,meson-axg-i2c"; |
| status = "disabled"; |
| reg = <0x0 0x05000 0x0 0x20>; |
| interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clkc CLKID_I2C>; |
| }; |
| |
| pwm_AO_ab: pwm@7000 { |
| compatible = "amlogic,meson-g12a-ao-pwm-ab"; |
| reg = <0x0 0x7000 0x0 0x20>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| ir: ir@8000 { |
| compatible = "amlogic,meson-gxbb-ir"; |
| reg = <0x0 0x8000 0x0 0x20>; |
| interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>; |
| status = "disabled"; |
| }; |
| |
| saradc: adc@9000 { |
| compatible = "amlogic,meson-g12a-saradc", |
| "amlogic,meson-saradc"; |
| reg = <0x0 0x9000 0x0 0x48>; |
| #io-channel-cells = <1>; |
| interrupts = <GIC_SPI 200 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&xtal>, |
| <&clkc_AO CLKID_AO_SAR_ADC>, |
| <&clkc_AO CLKID_AO_SAR_ADC_CLK>, |
| <&clkc_AO CLKID_AO_SAR_ADC_SEL>; |
| clock-names = "clkin", "core", "adc_clk", "adc_sel"; |
| status = "disabled"; |
| }; |
| }; |
| |
| vdec: video-decoder@ff620000 { |
| compatible = "amlogic,g12a-vdec"; |
| reg = <0x0 0xff620000 0x0 0x10000>, |
| <0x0 0xffd0e180 0x0 0xe4>; |
| reg-names = "dos", "esparser"; |
| interrupts = <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "vdec", "esparser"; |
| |
| amlogic,ao-sysctrl = <&rti>; |
| amlogic,canvas = <&canvas>; |
| |
| clocks = <&clkc CLKID_PARSER>, |
| <&clkc CLKID_DOS>, |
| <&clkc CLKID_VDEC_1>, |
| <&clkc CLKID_VDEC_HEVC>, |
| <&clkc CLKID_VDEC_HEVCF>; |
| clock-names = "dos_parser", "dos", "vdec_1", |
| "vdec_hevc", "vdec_hevcf"; |
| resets = <&reset RESET_PARSER>; |
| reset-names = "esparser"; |
| }; |
| |
| vpu: vpu@ff900000 { |
| compatible = "amlogic,meson-g12a-vpu"; |
| reg = <0x0 0xff900000 0x0 0x100000>, |
| <0x0 0xff63c000 0x0 0x1000>; |
| reg-names = "vpu", "hhi"; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| amlogic,canvas = <&canvas>; |
| |
| /* CVBS VDAC output port */ |
| cvbs_vdac_port: port@0 { |
| reg = <0>; |
| }; |
| |
| /* HDMI-TX output port */ |
| hdmi_tx_port: port@1 { |
| reg = <1>; |
| |
| hdmi_tx_out: endpoint { |
| remote-endpoint = <&hdmi_tx_in>; |
| }; |
| }; |
| |
| /* DPI output port */ |
| dpi_port: port@2 { |
| reg = <2>; |
| |
| dpi_out: endpoint { |
| remote-endpoint = <&mipi_dsi_in>; |
| }; |
| }; |
| }; |
| |
| gic: interrupt-controller@ffc01000 { |
| compatible = "arm,gic-400"; |
| reg = <0x0 0xffc01000 0 0x1000>, |
| <0x0 0xffc02000 0 0x2000>, |
| <0x0 0xffc04000 0 0x2000>, |
| <0x0 0xffc06000 0 0x2000>; |
| interrupt-controller; |
| interrupts = <GIC_PPI 9 |
| (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>; |
| #interrupt-cells = <3>; |
| #address-cells = <0>; |
| }; |
| |
| cbus: bus@ffd00000 { |
| compatible = "simple-bus"; |
| reg = <0x0 0xffd00000 0x0 0x100000>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0x0 0x0 0x0 0xffd00000 0x0 0x100000>; |
| |
| reset: reset-controller@1004 { |
| compatible = "amlogic,meson-axg-reset"; |
| reg = <0x0 0x1004 0x0 0x9c>; |
| #reset-cells = <1>; |
| }; |
| |
| gpio_intc: interrupt-controller@f080 { |
| compatible = "amlogic,meson-g12a-gpio-intc", |
| "amlogic,meson-gpio-intc"; |
| reg = <0x0 0xf080 0x0 0x10>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>; |
| }; |
| |
| mipi_dsi: dsi@7000 { |
| compatible = "amlogic,meson-g12a-dw-mipi-dsi"; |
| reg = <0x0 0x7000 0x0 0x1000>; |
| resets = <&reset RESET_MIPI_DSI_HOST>; |
| reset-names = "top"; |
| clocks = <&clkc CLKID_MIPI_DSI_HOST>, |
| <&clkc CLKID_MIPI_DSI_PXCLK>, |
| <&clkc CLKID_CTS_ENCL>; |
| clock-names = "pclk", "bit", "px"; |
| phys = <&mipi_dphy>; |
| phy-names = "dphy"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| |
| assigned-clocks = <&clkc CLKID_MIPI_DSI_PXCLK_SEL>, |
| <&clkc CLKID_CTS_ENCL_SEL>, |
| <&clkc CLKID_VCLK2_SEL>; |
| assigned-clock-parents = <&clkc CLKID_GP0_PLL>, |
| <&clkc CLKID_VCLK2_DIV1>, |
| <&clkc CLKID_GP0_PLL>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| /* VPU VENC Input */ |
| mipi_dsi_venc_port: port@0 { |
| reg = <0>; |
| |
| mipi_dsi_in: endpoint { |
| remote-endpoint = <&dpi_out>; |
| }; |
| }; |
| |
| /* DSI Output */ |
| mipi_dsi_panel_port: port@1 { |
| reg = <1>; |
| }; |
| }; |
| }; |
| |
| watchdog: watchdog@f0d0 { |
| compatible = "amlogic,meson-gxbb-wdt"; |
| reg = <0x0 0xf0d0 0x0 0x10>; |
| clocks = <&xtal>; |
| }; |
| |
| spicc0: spi@13000 { |
| compatible = "amlogic,meson-g12a-spicc"; |
| reg = <0x0 0x13000 0x0 0x44>; |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clkc CLKID_SPICC0>, |
| <&clkc CLKID_SPICC0_SCLK>; |
| clock-names = "core", "pclk"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spicc1: spi@15000 { |
| compatible = "amlogic,meson-g12a-spicc"; |
| reg = <0x0 0x15000 0x0 0x44>; |
| interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clkc CLKID_SPICC1>, |
| <&clkc CLKID_SPICC1_SCLK>; |
| clock-names = "core", "pclk"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spifc: spi@14000 { |
| compatible = "amlogic,meson-gxbb-spifc"; |
| status = "disabled"; |
| reg = <0x0 0x14000 0x0 0x80>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clkc CLKID_CLK81>; |
| }; |
| |
| pwm_ef: pwm@19000 { |
| compatible = "amlogic,meson-g12a-ee-pwm"; |
| reg = <0x0 0x19000 0x0 0x20>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm_cd: pwm@1a000 { |
| compatible = "amlogic,meson-g12a-ee-pwm"; |
| reg = <0x0 0x1a000 0x0 0x20>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pwm_ab: pwm@1b000 { |
| compatible = "amlogic,meson-g12a-ee-pwm"; |
| reg = <0x0 0x1b000 0x0 0x20>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@1c000 { |
| compatible = "amlogic,meson-axg-i2c"; |
| status = "disabled"; |
| reg = <0x0 0x1c000 0x0 0x20>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clkc CLKID_I2C>; |
| }; |
| |
| i2c2: i2c@1d000 { |
| compatible = "amlogic,meson-axg-i2c"; |
| status = "disabled"; |
| reg = <0x0 0x1d000 0x0 0x20>; |
| interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clkc CLKID_I2C>; |
| }; |
| |
| i2c1: i2c@1e000 { |
| compatible = "amlogic,meson-axg-i2c"; |
| status = "disabled"; |
| reg = <0x0 0x1e000 0x0 0x20>; |
| interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clkc CLKID_I2C>; |
| }; |
| |
| i2c0: i2c@1f000 { |
| compatible = "amlogic,meson-axg-i2c"; |
| status = "disabled"; |
| reg = <0x0 0x1f000 0x0 0x20>; |
| interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clkc CLKID_I2C>; |
| }; |
| |
| clk_msr: clock-measure@18000 { |
| compatible = "amlogic,meson-g12a-clk-measure"; |
| reg = <0x0 0x18000 0x0 0x10>; |
| }; |
| |
| uart_C: serial@22000 { |
| compatible = "amlogic,meson-g12a-uart", |
| "amlogic,meson-gx-uart"; |
| reg = <0x0 0x22000 0x0 0x18>; |
| interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>; |
| clock-names = "xtal", "pclk", "baud"; |
| status = "disabled"; |
| }; |
| |
| uart_B: serial@23000 { |
| compatible = "amlogic,meson-g12a-uart", |
| "amlogic,meson-gx-uart"; |
| reg = <0x0 0x23000 0x0 0x18>; |
| interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>; |
| clock-names = "xtal", "pclk", "baud"; |
| status = "disabled"; |
| }; |
| |
| uart_A: serial@24000 { |
| compatible = "amlogic,meson-g12a-uart", |
| "amlogic,meson-gx-uart"; |
| reg = <0x0 0x24000 0x0 0x18>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>; |
| clock-names = "xtal", "pclk", "baud"; |
| status = "disabled"; |
| fifo-size = <128>; |
| }; |
| }; |
| |
| sd_emmc_a: mmc@ffe03000 { |
| compatible = "amlogic,meson-axg-mmc"; |
| reg = <0x0 0xffe03000 0x0 0x800>; |
| interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| clocks = <&clkc CLKID_SD_EMMC_A>, |
| <&clkc CLKID_SD_EMMC_A_CLK0>, |
| <&clkc CLKID_FCLK_DIV2>; |
| clock-names = "core", "clkin0", "clkin1"; |
| resets = <&reset RESET_SD_EMMC_A>; |
| }; |
| |
| sd_emmc_b: mmc@ffe05000 { |
| compatible = "amlogic,meson-axg-mmc"; |
| reg = <0x0 0xffe05000 0x0 0x800>; |
| interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| clocks = <&clkc CLKID_SD_EMMC_B>, |
| <&clkc CLKID_SD_EMMC_B_CLK0>, |
| <&clkc CLKID_FCLK_DIV2>; |
| clock-names = "core", "clkin0", "clkin1"; |
| resets = <&reset RESET_SD_EMMC_B>; |
| }; |
| |
| sd_emmc_c: mmc@ffe07000 { |
| compatible = "amlogic,meson-axg-mmc"; |
| reg = <0x0 0xffe07000 0x0 0x800>; |
| interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| clocks = <&clkc CLKID_SD_EMMC_C>, |
| <&clkc CLKID_SD_EMMC_C_CLK0>, |
| <&clkc CLKID_FCLK_DIV2>; |
| clock-names = "core", "clkin0", "clkin1"; |
| resets = <&reset RESET_SD_EMMC_C>; |
| }; |
| |
| usb: usb@ffe09000 { |
| status = "disabled"; |
| compatible = "amlogic,meson-g12a-usb-ctrl"; |
| reg = <0x0 0xffe09000 0x0 0xa0>; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| clocks = <&clkc CLKID_USB>; |
| resets = <&reset RESET_USB>; |
| |
| dr_mode = "otg"; |
| |
| phys = <&usb2_phy0>, <&usb2_phy1>, |
| <&usb3_pcie_phy PHY_TYPE_USB3>; |
| phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0"; |
| |
| dwc2: usb@ff400000 { |
| compatible = "amlogic,meson-g12a-usb", "snps,dwc2"; |
| reg = <0x0 0xff400000 0x0 0x40000>; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clkc CLKID_USB1_DDR_BRIDGE>; |
| clock-names = "otg"; |
| phys = <&usb2_phy1>; |
| phy-names = "usb2-phy"; |
| dr_mode = "peripheral"; |
| g-rx-fifo-size = <192>; |
| g-np-tx-fifo-size = <128>; |
| g-tx-fifo-size = <128 128 16 16 16>; |
| }; |
| |
| dwc3: usb@ff500000 { |
| compatible = "snps,dwc3"; |
| reg = <0x0 0xff500000 0x0 0x100000>; |
| interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; |
| dr_mode = "host"; |
| snps,dis_u2_susphy_quirk; |
| snps,quirk-frame-length-adjustment = <0x20>; |
| snps,parkmode-disable-ss-quirk; |
| }; |
| }; |
| |
| mali: gpu@ffe40000 { |
| compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost"; |
| reg = <0x0 0xffe40000 0x0 0x40000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "job", "mmu", "gpu"; |
| clocks = <&clkc CLKID_MALI>; |
| resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>; |
| operating-points-v2 = <&gpu_opp_table>; |
| #cooling-cells = <2>; |
| }; |
| }; |
| |
| thermal-zones { |
| cpu_thermal: cpu-thermal { |
| polling-delay = <1000>; |
| polling-delay-passive = <100>; |
| thermal-sensors = <&cpu_temp>; |
| |
| trips { |
| cpu_passive: cpu-passive { |
| temperature = <85000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "passive"; |
| }; |
| |
| cpu_hot: cpu-hot { |
| temperature = <95000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "hot"; |
| }; |
| |
| cpu_critical: cpu-critical { |
| temperature = <110000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| ddr_thermal: ddr-thermal { |
| polling-delay = <1000>; |
| polling-delay-passive = <100>; |
| thermal-sensors = <&ddr_temp>; |
| |
| trips { |
| ddr_passive: ddr-passive { |
| temperature = <85000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "passive"; |
| }; |
| |
| ddr_critical: ddr-critical { |
| temperature = <110000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map { |
| trip = <&ddr_passive>; |
| cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 13 |
| (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 14 |
| (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 11 |
| (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 10 |
| (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>; |
| arm,no-tick-in-suspend; |
| }; |
| |
| xtal: xtal-clk { |
| compatible = "fixed-clock"; |
| clock-frequency = <24000000>; |
| clock-output-names = "xtal"; |
| #clock-cells = <0>; |
| }; |
| |
| npu: npu@ff100000 { |
| compatible = "vivante,gc"; |
| reg = <0x0 0xff100000 0x0 0x20000>; |
| interrupts = <0 147 4>; |
| clocks = <&clkc CLKID_NNA_CORE_CLK>, |
| <&clkc CLKID_NNA_AXI_CLK>; |
| clock-names = "core", "bus"; |
| assigned-clocks = <&clkc CLKID_NNA_CORE_CLK>, |
| <&clkc CLKID_NNA_AXI_CLK>; |
| assigned-clock-rates = <800000000>, <800000000>; |
| resets = <&reset RESET_NNA>; |
| status = "disabled"; |
| }; |
| }; |
