arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi - linux - Git at Google

 // SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
 /*
  * Copyright 2020-2021 TQ-Systems GmbH
  */

 #include "imx8mn.dtsi"

 / {
 	model = "TQ-Systems i.MX8MN TQMa8MxNL";
 	compatible = "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";

 	memory@40000000 {
 		device_type = "memory";
 		/*  our minimum RAM config will be 1024 MiB */
 		reg = <0x00000000 0x40000000 0 0x40000000>;
 	};

 	/* e-MMC IO, needed for HS modes */
 	reg_vcc1v8: regulator-vcc1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "TQMA8MXNL_VCC1V8";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 	};

 	reg_vcc3v3: regulator-vcc3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "TQMA8MXNL_VCC3V3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};

 	reserved-memory {
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;

 		/* global autoconfigured region for contiguous allocations */
 		linux,cma {
 			compatible = "shared-dma-pool";
 			reusable;
 			/* 640 MiB */
 			size = <0 0x28000000>;
 			/*  1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
 			alloc-ranges = <0 0x40000000 0 0x78000000>;
 			linux,cma-default;
 		};
 	};
 };

 &A53_0 {
 	cpu-supply = <&buck2_reg>;
 };

 &flexspi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexspi>;
 	status = "okay";

 	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <84000000>;
 		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;

 		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
 		};
 	};
 };

 &i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	pinctrl-1 = <&pinctrl_i2c1_gpio>;
 	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";

 	sensor0: temperature-sensor@1b {
 		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
 		reg = <0x1b>;
 	};

 	pca9450: pmic@25 {
 		compatible = "nxp,pca9450a";
 		reg = <0x25>;

 		/* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
 		pinctrl-0 = <&pinctrl_pmic>;
 		pinctrl-names = "default";
 		interrupt-parent = <&gpio1>;
 		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;

 		regulators {
 			/* V_0V85_SOC: 0.85 .. 0.95 */
 			buck1_reg: BUCK1 {
 				regulator-name = "BUCK1";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-ramp-delay = <3125>;
 			};

 			/* VDD_ARM */
 			buck2_reg: BUCK2 {
 				regulator-name = "BUCK2";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-boot-on;
 				regulator-always-on;
 				nxp,dvs-run-voltage = <950000>;
 				nxp,dvs-standby-voltage = <850000>;
 				regulator-ramp-delay = <3125>;
 			};

 			/* V_0V85_GPU / DRAM: shall be equal to BUCK1 for i.MX8MN */
 			buck3_reg: BUCK3 {
 				regulator-name = "BUCK3";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-ramp-delay = <3125>;
 			};

 			/* VCC3V3 -> VMMC, ... must not be changed */
 			buck4_reg: BUCK4 {
 				regulator-name = "BUCK4";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};

 			/* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
 			buck5_reg: BUCK5 {
 				regulator-name = "BUCK5";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};

 			/* V_1V1 -> RAM, ... must not be changed */
 			buck6_reg: BUCK6 {
 				regulator-name = "BUCK6";
 				regulator-min-microvolt = <1100000>;
 				regulator-max-microvolt = <1100000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};

 			/* V_1V8_SNVS */
 			ldo1_reg: LDO1 {
 				regulator-name = "LDO1";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};

 			/* V_0V8_SNVS */
 			ldo2_reg: LDO2 {
 				regulator-name = "LDO2";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <850000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};

 			/* V_1V8_ANA */
 			ldo3_reg: LDO3 {
 				regulator-name = "LDO3";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};

 			/* V_0V9_MIPI */
 			ldo4_reg: LDO4 {
 				regulator-name = "LDO4";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <900000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};

 			/* VCC SD IO - switched using SD2 VSELECT */
 			ldo5_reg: LDO5 {
 				regulator-name = "LDO5";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 			};
 		};
 	};

 	pcf85063: rtc@51 {
 		compatible = "nxp,pcf85063a";
 		reg = <0x51>;
 		quartz-load-femtofarads = <7000>;
 	};

 	eeprom1: eeprom@53 {
 		compatible = "nxp,se97b", "atmel,24c02";
 		read-only;
 		reg = <0x53>;
 		pagesize = <16>;
 		vcc-supply = <&reg_vcc3v3>;
 	};

 	eeprom0: eeprom@57 {
 		compatible = "atmel,24c64";
 		reg = <0x57>;
 		pagesize = <32>;
 		vcc-supply = <&reg_vcc3v3>;
 	};
 };

 &mipi_dsi {
 	vddcore-supply = <&ldo4_reg>;
 	vddio-supply = <&ldo3_reg>;
 };

 &usdhc3 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
 	bus-width = <8>;
 	non-removable;
 	no-sd;
 	no-sdio;
 	vmmc-supply = <&reg_vcc3v3>;
 	vqmmc-supply = <&reg_vcc1v8>;
 	status = "okay";
 };

 /*
  * Attention:
  * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
  * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
  */
 &wdog1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wdog>;
 	fsl,ext-reset-output;
 	status = "okay";
 };

 &iomuxc {
 	pinctrl_flexspi: flexspigrp {
 		fsl,pins = <MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x84>,
 			   <MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B	0x84>,
 			   <MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0	0x84>,
 			   <MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1	0x84>,
 			   <MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2	0x84>,
 			   <MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3	0x84>;
 	};

 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL		0x400001c4>,
 			   <MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA		0x400001c4>;
 	};

 	pinctrl_i2c1_gpio: i2c1gpiogrp {
 		fsl,pins = <MX8MN_IOMUXC_I2C1_SCL_GPIO5_IO14	0x400001c4>,
 			   <MX8MN_IOMUXC_I2C1_SDA_GPIO5_IO15	0x400001c4>;
 	};

 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8	0x84>;
 	};

 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
 		fsl,pins = <MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x84>;
 	};

 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d4>,
 			   <MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
 			   <MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
 			   <MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B	0x84>;
 	};

 	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d2>,
 			   <MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
 			   <MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
 			   <MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B	0x84>;
 	};

 	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 		fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d6>,
 			   <MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
 			   <MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
 			   <MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
 			   <MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B	0x84>;
 	};

 	pinctrl_wdog: wdoggrp {
 		fsl,pins = <MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0x84>;
 	};
 };
	// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
	/*
	* Copyright 2020-2021 TQ-Systems GmbH
	*/

	#include "imx8mn.dtsi"

	/ {
	model = "TQ-Systems i.MX8MN TQMa8MxNL";
	compatible = "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";

	memory@40000000 {
	device_type = "memory";
	/* our minimum RAM config will be 1024 MiB */
	reg = <0x00000000 0x40000000 0 0x40000000>;
	};

	/* e-MMC IO, needed for HS modes */
	reg_vcc1v8: regulator-vcc1v8 {
	compatible = "regulator-fixed";
	regulator-name = "TQMA8MXNL_VCC1V8";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	};

	reg_vcc3v3: regulator-vcc3v3 {
	compatible = "regulator-fixed";
	regulator-name = "TQMA8MXNL_VCC3V3";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	};

	reserved-memory {
	#address-cells = <2>;
	#size-cells = <2>;
	ranges;

	/* global autoconfigured region for contiguous allocations */
	linux,cma {
	compatible = "shared-dma-pool";
	reusable;
	/* 640 MiB */
	size = <0 0x28000000>;
	/* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
	alloc-ranges = <0 0x40000000 0 0x78000000>;
	linux,cma-default;
	};
	};
	};

	&A53_0 {
	cpu-supply = <&buck2_reg>;
	};

	&flexspi {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_flexspi>;
	status = "okay";

	flash0: flash@0 {
	compatible = "jedec,spi-nor";
	reg = <0>;
	spi-max-frequency = <84000000>;
	spi-tx-bus-width = <1>;
	spi-rx-bus-width = <4>;

	partitions {
	compatible = "fixed-partitions";
	#address-cells = <1>;
	#size-cells = <1>;
	};
	};
	};

	&i2c1 {
	clock-frequency = <100000>;
	pinctrl-names = "default", "gpio";
	pinctrl-0 = <&pinctrl_i2c1>;
	pinctrl-1 = <&pinctrl_i2c1_gpio>;
	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH \| GPIO_OPEN_DRAIN)>;
	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH \| GPIO_OPEN_DRAIN)>;
	status = "okay";

	sensor0: temperature-sensor@1b {
	compatible = "nxp,se97b", "jedec,jc-42.4-temp";
	reg = <0x1b>;
	};

	pca9450: pmic@25 {
	compatible = "nxp,pca9450a";
	reg = <0x25>;

	/* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
	pinctrl-0 = <&pinctrl_pmic>;
	pinctrl-names = "default";
	interrupt-parent = <&gpio1>;
	interrupts = <8 IRQ_TYPE_LEVEL_LOW>;

	regulators {
	/* V_0V85_SOC: 0.85 .. 0.95 */
	buck1_reg: BUCK1 {
	regulator-name = "BUCK1";
	regulator-min-microvolt = <850000>;
	regulator-max-microvolt = <950000>;
	regulator-boot-on;
	regulator-always-on;
	regulator-ramp-delay = <3125>;
	};

	/* VDD_ARM */
	buck2_reg: BUCK2 {
	regulator-name = "BUCK2";
	regulator-min-microvolt = <850000>;
	regulator-max-microvolt = <1000000>;
	regulator-boot-on;
	regulator-always-on;
	nxp,dvs-run-voltage = <950000>;
	nxp,dvs-standby-voltage = <850000>;
	regulator-ramp-delay = <3125>;
	};

	/* V_0V85_GPU / DRAM: shall be equal to BUCK1 for i.MX8MN */
	buck3_reg: BUCK3 {
	regulator-name = "BUCK3";
	regulator-min-microvolt = <850000>;
	regulator-max-microvolt = <950000>;
	regulator-boot-on;
	regulator-always-on;
	regulator-ramp-delay = <3125>;
	};

	/* VCC3V3 -> VMMC, ... must not be changed */
	buck4_reg: BUCK4 {
	regulator-name = "BUCK4";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-boot-on;
	regulator-always-on;
	};

	/* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
	buck5_reg: BUCK5 {
	regulator-name = "BUCK5";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-boot-on;
	regulator-always-on;
	};

	/* V_1V1 -> RAM, ... must not be changed */
	buck6_reg: BUCK6 {
	regulator-name = "BUCK6";
	regulator-min-microvolt = <1100000>;
	regulator-max-microvolt = <1100000>;
	regulator-boot-on;
	regulator-always-on;
	};

	/* V_1V8_SNVS */
	ldo1_reg: LDO1 {
	regulator-name = "LDO1";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-boot-on;
	regulator-always-on;
	};

	/* V_0V8_SNVS */
	ldo2_reg: LDO2 {
	regulator-name = "LDO2";
	regulator-min-microvolt = <800000>;
	regulator-max-microvolt = <850000>;
	regulator-boot-on;
	regulator-always-on;
	};

	/* V_1V8_ANA */
	ldo3_reg: LDO3 {
	regulator-name = "LDO3";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-boot-on;
	regulator-always-on;
	};

	/* V_0V9_MIPI */
	ldo4_reg: LDO4 {
	regulator-name = "LDO4";
	regulator-min-microvolt = <900000>;
	regulator-max-microvolt = <900000>;
	regulator-boot-on;
	regulator-always-on;
	};

	/* VCC SD IO - switched using SD2 VSELECT */
	ldo5_reg: LDO5 {
	regulator-name = "LDO5";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <3300000>;
	};
	};
	};

	pcf85063: rtc@51 {
	compatible = "nxp,pcf85063a";
	reg = <0x51>;
	quartz-load-femtofarads = <7000>;
	};

	eeprom1: eeprom@53 {
	compatible = "nxp,se97b", "atmel,24c02";
	read-only;
	reg = <0x53>;
	pagesize = <16>;
	vcc-supply = <&reg_vcc3v3>;
	};

	eeprom0: eeprom@57 {
	compatible = "atmel,24c64";
	reg = <0x57>;
	pagesize = <32>;
	vcc-supply = <&reg_vcc3v3>;
	};
	};

	&mipi_dsi {
	vddcore-supply = <&ldo4_reg>;
	vddio-supply = <&ldo3_reg>;
	};

	&usdhc3 {
	pinctrl-names = "default", "state_100mhz", "state_200mhz";
	pinctrl-0 = <&pinctrl_usdhc3>;
	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
	bus-width = <8>;
	non-removable;
	no-sd;
	no-sdio;
	vmmc-supply = <&reg_vcc3v3>;
	vqmmc-supply = <&reg_vcc1v8>;
	status = "okay";
	};

	/*
	* Attention:
	* wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
	* without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
	*/
	&wdog1 {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_wdog>;
	fsl,ext-reset-output;
	status = "okay";
	};

	&iomuxc {
	pinctrl_flexspi: flexspigrp {
	fsl,pins = <MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x84>,
	<MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x84>,
	<MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x84>,
	<MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x84>,
	<MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x84>,
	<MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x84>;
	};

	pinctrl_i2c1: i2c1grp {
	fsl,pins = <MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c4>,
	<MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c4>;
	};

	pinctrl_i2c1_gpio: i2c1gpiogrp {
	fsl,pins = <MX8MN_IOMUXC_I2C1_SCL_GPIO5_IO14 0x400001c4>,
	<MX8MN_IOMUXC_I2C1_SDA_GPIO5_IO15 0x400001c4>;
	};

	pinctrl_pmic: pmicgrp {
	fsl,pins = <MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x84>;
	};

	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
	fsl,pins = <MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84>;
	};

	pinctrl_usdhc3: usdhc3grp {
	fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4>,
	<MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
	<MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
	<MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
	<MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
	<MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
	<MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
	<MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
	<MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
	<MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
	<MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
	<MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84>;
	};

	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
	fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2>,
	<MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
	<MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
	<MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
	<MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
	<MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
	<MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
	<MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
	<MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
	<MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
	<MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
	<MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84>;
	};

	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
	fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6>,
	<MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
	<MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
	<MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
	<MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
	<MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
	<MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
	<MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
	<MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
	<MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
	<MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
	<MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84>;
	};

	pinctrl_wdog: wdoggrp {
	fsl,pins = <MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84>;
	};
	};