| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright 2018-2019 NXP |
| * Dong Aisheng <aisheng.dong@nxp.com> |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/usb/pd.h> |
| #include "imx8qm.dtsi" |
| |
| / { |
| model = "Freescale i.MX8QM MEK"; |
| compatible = "fsl,imx8qm-mek", "fsl,imx8qm"; |
| |
| chosen { |
| stdout-path = &lpuart0; |
| }; |
| |
| cpus { |
| /delete-node/ cpu-map; |
| /delete-node/ cpu@100; |
| /delete-node/ cpu@101; |
| }; |
| |
| thermal-zones { |
| /delete-node/ cpu1-thermal; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x00000000 0x80000000 0 0x40000000>; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| vdev0vring0: memory@90000000 { |
| reg = <0 0x90000000 0 0x8000>; |
| no-map; |
| }; |
| |
| vdev0vring1: memory@90008000 { |
| reg = <0 0x90008000 0 0x8000>; |
| no-map; |
| }; |
| |
| vdev1vring0: memory@90010000 { |
| reg = <0 0x90010000 0 0x8000>; |
| no-map; |
| }; |
| |
| vdev1vring1: memory@90018000 { |
| reg = <0 0x90018000 0 0x8000>; |
| no-map; |
| }; |
| |
| rsc_table0: memory@900ff000 { |
| reg = <0 0x900ff000 0 0x1000>; |
| no-map; |
| }; |
| |
| vdev2vring0: memory@90100000 { |
| reg = <0 0x90100000 0 0x8000>; |
| no-map; |
| }; |
| |
| vdev2vring1: memory@90108000 { |
| reg = <0 0x90108000 0 0x8000>; |
| no-map; |
| }; |
| |
| vdev3vring0: memory@90110000 { |
| reg = <0 0x90110000 0 0x8000>; |
| no-map; |
| }; |
| |
| vdev3vring1: memory@90118000 { |
| reg = <0 0x90118000 0 0x8000>; |
| no-map; |
| }; |
| |
| rsc_table1: memory@901ff000 { |
| reg = <0 0x901ff000 0 0x1000>; |
| no-map; |
| }; |
| |
| vdevbuffer: memory@90400000 { |
| compatible = "shared-dma-pool"; |
| reg = <0 0x90400000 0 0x100000>; |
| no-map; |
| }; |
| }; |
| |
| lvds_backlight0: backlight-lvds0 { |
| compatible = "pwm-backlight"; |
| pwms = <&qm_pwm_lvds0 0 100000 0>; |
| brightness-levels = <0 100>; |
| num-interpolated-steps = <100>; |
| default-brightness-level = <80>; |
| }; |
| |
| lvds_backlight1: backlight-lvds1 { |
| compatible = "pwm-backlight"; |
| pwms = <&pwm_lvds1 0 100000 0>; |
| brightness-levels = <0 100>; |
| num-interpolated-steps = <100>; |
| default-brightness-level = <80>; |
| }; |
| |
| mux-controller { |
| compatible = "nxp,cbdtu02043", "gpio-sbu-mux"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_typec_mux>; |
| select-gpios = <&lsio_gpio4 6 GPIO_ACTIVE_LOW>; |
| enable-gpios = <&lsio_gpio4 19 GPIO_ACTIVE_HIGH>; |
| orientation-switch; |
| |
| port { |
| usb3_data_ss: endpoint { |
| remote-endpoint = <&typec_con_ss>; |
| }; |
| }; |
| }; |
| |
| reg_usdhc2_vmmc: usdhc2-vmmc { |
| compatible = "regulator-fixed"; |
| regulator-name = "SD1_SPWR"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| gpio = <&lsio_gpio4 7 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_fec2_supply: regulator-fec2-nvcc { |
| compatible = "regulator-fixed"; |
| regulator-name = "fec2_nvcc"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| gpio = <&max7322 0 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_can01_en: regulator-can01-gen { |
| compatible = "regulator-fixed"; |
| regulator-name = "can01-en"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&pca6416 3 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_can2_en: regulator-can2-gen { |
| compatible = "regulator-fixed"; |
| regulator-name = "can2-en"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&pca6416 4 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| reg_can01_stby: regulator-can01-stby { |
| compatible = "regulator-fixed"; |
| regulator-name = "can01-stby"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&pca6416 5 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| vin-supply = <®_can01_en>; |
| }; |
| |
| reg_can2_stby: regulator-can2-stby { |
| compatible = "regulator-fixed"; |
| regulator-name = "can2-stby"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&pca6416 6 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| vin-supply = <®_can2_en>; |
| }; |
| |
| reg_vref_1v8: regulator-adc-vref { |
| compatible = "regulator-fixed"; |
| regulator-name = "vref_1v8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| bt_sco_codec: audio-codec-bt { |
| compatible = "linux,bt-sco"; |
| #sound-dai-cells = <1>; |
| }; |
| |
| sound-bt-sco { |
| compatible = "simple-audio-card"; |
| simple-audio-card,name = "bt-sco-audio"; |
| simple-audio-card,format = "dsp_a"; |
| simple-audio-card,bitclock-inversion; |
| simple-audio-card,frame-master = <&btcpu>; |
| simple-audio-card,bitclock-master = <&btcpu>; |
| |
| btcpu: simple-audio-card,cpu { |
| sound-dai = <&sai0>; |
| dai-tdm-slot-num = <2>; |
| dai-tdm-slot-width = <16>; |
| }; |
| |
| simple-audio-card,codec { |
| sound-dai = <&bt_sco_codec 1>; |
| }; |
| }; |
| |
| sound-wm8960 { |
| compatible = "fsl,imx-audio-wm8960"; |
| model = "wm8960-audio"; |
| audio-cpu = <&sai1>; |
| audio-codec = <&wm8960>; |
| hp-det-gpio = <&lsio_gpio0 31 GPIO_ACTIVE_HIGH>; |
| audio-routing = "Headphone Jack", "HP_L", |
| "Headphone Jack", "HP_R", |
| "Ext Spk", "SPK_LP", |
| "Ext Spk", "SPK_LN", |
| "Ext Spk", "SPK_RP", |
| "Ext Spk", "SPK_RN", |
| "LINPUT1", "Mic Jack", |
| "Mic Jack", "MICB"; |
| }; |
| |
| imx8qm-cm4-0 { |
| compatible = "fsl,imx8qm-cm4"; |
| clocks = <&clk_dummy>; |
| mbox-names = "tx", "rx", "rxdb"; |
| mboxes = <&lsio_mu5 0 1 |
| &lsio_mu5 1 1 |
| &lsio_mu5 3 1>; |
| memory-region = <&vdevbuffer>, <&vdev0vring0>, <&vdev0vring1>, |
| <&vdev1vring0>, <&vdev1vring1>, <&rsc_table0>; |
| power-domains = <&pd IMX_SC_R_M4_0_PID0>, <&pd IMX_SC_R_M4_0_MU_1A>; |
| |
| fsl,resource-id = <IMX_SC_R_M4_0_PID0>; |
| fsl,entry-address = <0x34fe0000>; |
| }; |
| |
| imx8qm-cm4-1 { |
| compatible = "fsl,imx8qm-cm4"; |
| clocks = <&clk_dummy>; |
| mbox-names = "tx", "rx", "rxdb"; |
| mboxes = <&lsio_mu6 0 1 |
| &lsio_mu6 1 1 |
| &lsio_mu6 3 1>; |
| memory-region = <&vdevbuffer>, <&vdev2vring0>, <&vdev2vring1>, |
| <&vdev3vring0>, <&vdev3vring1>, <&rsc_table1>; |
| power-domains = <&pd IMX_SC_R_M4_1_PID0>, <&pd IMX_SC_R_M4_1_MU_1A>; |
| |
| fsl,resource-id = <IMX_SC_R_M4_1_PID0>; |
| fsl,entry-address = <0x38fe0000>; |
| }; |
| |
| }; |
| |
| &adc0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_adc0>; |
| vref-supply = <®_vref_1v8>; |
| status = "okay"; |
| }; |
| |
| &amix { |
| status = "okay"; |
| }; |
| |
| &asrc0 { |
| fsl,asrc-rate = <48000>; |
| status = "okay"; |
| }; |
| |
| &cm41_i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cm41_i2c>; |
| status = "okay"; |
| |
| pca6416: gpio@20 { |
| compatible = "ti,tca6416"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| |
| &cm41_intmux { |
| status = "okay"; |
| }; |
| |
| &i2c0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c0>; |
| status = "okay"; |
| |
| accelerometer@19 { |
| compatible = "st,lsm303agr-accel"; |
| reg = <0x19>; |
| }; |
| |
| gyrometer@20 { |
| compatible = "nxp,fxas21002c"; |
| reg = <0x20>; |
| }; |
| |
| light-sensor@44 { |
| compatible = "isil,isl29023"; |
| reg = <0x44>; |
| interrupt-parent = <&lsio_gpio4>; |
| interrupts = <11 IRQ_TYPE_EDGE_FALLING>; |
| }; |
| |
| pressure-sensor@60 { |
| compatible = "fsl,mpl3115"; |
| reg = <0x60>; |
| }; |
| |
| max7322: gpio@68 { |
| compatible = "maxim,max7322"; |
| reg = <0x68>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| gyrometer@69 { |
| compatible = "st,l3g4200d-gyro"; |
| reg = <0x69>; |
| }; |
| |
| ptn5110: tcpc@51 { |
| compatible = "nxp,ptn5110", "tcpci"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_typec>; |
| reg = <0x51>; |
| interrupt-parent = <&lsio_gpio4>; |
| interrupts = <26 IRQ_TYPE_LEVEL_LOW>; |
| status = "okay"; |
| |
| usb_con1: connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "source"; |
| data-role = "dual"; |
| source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| typec_dr_sw: endpoint { |
| remote-endpoint = <&usb3_drd_sw>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| typec_con_ss: endpoint { |
| remote-endpoint = <&usb3_data_ss>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <100000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| pinctrl-1 = <&pinctrl_i2c1_gpio>; |
| scl-gpios = <&lsio_gpio0 14 GPIO_ACTIVE_HIGH>; |
| sda-gpios = <&lsio_gpio0 15 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| |
| wm8960: audio-codec@1a { |
| compatible = "wlf,wm8960"; |
| reg = <0x1a>; |
| clocks = <&mclkout0_lpcg IMX_LPCG_CLK_0>; |
| clock-names = "mclk"; |
| assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>, |
| <&mclkout0_lpcg IMX_LPCG_CLK_0>; |
| assigned-clock-rates = <786432000>, <49152000>, <12288000>, <12288000>; |
| wlf,shared-lrclk; |
| wlf,hp-cfg = <2 2 3>; |
| wlf,gpio-cfg = <1 3>; |
| }; |
| }; |
| |
| &i2c1_lvds0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lvds0_lpi2c1>; |
| clock-frequency = <100000>; |
| status = "okay"; |
| }; |
| |
| &i2c1_lvds1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lvds1_lpi2c1>; |
| clock-frequency = <100000>; |
| status = "okay"; |
| }; |
| |
| &i2c0_mipi0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mipi0_lpi2c0>; |
| clock-frequency = <100000>; |
| status = "okay"; |
| }; |
| |
| &i2c0_mipi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mipi1_lpi2c0>; |
| clock-frequency = <100000>; |
| status = "okay"; |
| }; |
| |
| &flexcan1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan1>; |
| xceiver-supply = <®_can01_stby>; |
| status = "okay"; |
| }; |
| |
| &flexcan2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan2>; |
| xceiver-supply = <®_can01_stby>; |
| status = "okay"; |
| }; |
| |
| &flexcan3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexcan3>; |
| xceiver-supply = <®_can2_stby>; |
| status = "okay"; |
| }; |
| |
| &lpuart0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lpuart0>; |
| status = "okay"; |
| }; |
| |
| &lpuart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lpuart2>; |
| status = "okay"; |
| }; |
| |
| &lpuart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lpuart3>; |
| status = "okay"; |
| }; |
| |
| &lpspi2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lpspi2 &pinctrl_lpspi2_cs>; |
| cs-gpios = <&lsio_gpio3 10 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| |
| &lsio_mu5 { |
| status = "okay"; |
| }; |
| |
| &lsio_mu6 { |
| status = "okay"; |
| }; |
| |
| &flexspi0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexspi0>; |
| status = "okay"; |
| |
| flash0: flash@0 { |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <133000000>; |
| spi-tx-bus-width = <8>; |
| spi-rx-bus-width = <8>; |
| }; |
| }; |
| |
| &fec1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec1>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <ðphy0>; |
| fsl,magic-packet; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy0: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0>; |
| }; |
| |
| ethphy1: ethernet-phy@1 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <1>; |
| }; |
| }; |
| }; |
| |
| &fec2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec2>; |
| phy-mode = "rgmii-txid"; |
| phy-handle = <ðphy1>; |
| phy-supply = <®_fec2_supply>; |
| nvmem-cells = <&fec_mac1>; |
| nvmem-cell-names = "mac-address"; |
| rx-internal-delay-ps = <2000>; |
| fsl,magic-packet; |
| status = "okay"; |
| }; |
| |
| &qm_pwm_lvds0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm_lvds0>; |
| status = "okay"; |
| }; |
| |
| &pwm_lvds1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm_lvds1>; |
| status = "okay"; |
| }; |
| |
| &usdhc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| bus-width = <8>; |
| no-sd; |
| no-sdio; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &usdhc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc2>; |
| bus-width = <4>; |
| vmmc-supply = <®_usdhc2_vmmc>; |
| cd-gpios = <&lsio_gpio5 22 GPIO_ACTIVE_LOW>; |
| wp-gpios = <&lsio_gpio5 21 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| &usb3_phy { |
| status = "okay"; |
| }; |
| |
| &usbotg3 { |
| status = "okay"; |
| }; |
| |
| &usbotg3_cdns3 { |
| dr_mode = "otg"; |
| usb-role-switch; |
| status = "okay"; |
| |
| port { |
| usb3_drd_sw: endpoint { |
| remote-endpoint = <&typec_dr_sw>; |
| }; |
| }; |
| }; |
| |
| &sai0 { |
| #sound-dai-cells = <0>; |
| assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>, |
| <&sai0_lpcg IMX_LPCG_CLK_4>; |
| assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sai0>; |
| status = "okay"; |
| }; |
| |
| &sai1 { |
| assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>, |
| <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>, |
| <&sai1_lpcg IMX_LPCG_CLK_4>; |
| assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sai1>; |
| status = "okay"; |
| }; |
| |
| &sai6 { |
| assigned-clocks = <&acm IMX_ADMA_ACM_SAI6_MCLK_SEL>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>, |
| <&sai6_lpcg IMX_LPCG_CLK_4>; |
| assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>; |
| assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>; |
| fsl,sai-asynchronous; |
| status = "okay"; |
| }; |
| |
| &sai7 { |
| assigned-clocks = <&acm IMX_ADMA_ACM_SAI7_MCLK_SEL>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>, |
| <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>, |
| <&sai7_lpcg IMX_LPCG_CLK_4>; |
| assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>; |
| assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>; |
| fsl,sai-asynchronous; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_hog>; |
| |
| pinctrl_hog: hoggrp { |
| fsl,pins = < |
| IMX8QM_MCLK_OUT0_AUD_ACM_MCLK_OUT0 0x0600004c |
| IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31 0x0600004c |
| >; |
| }; |
| |
| pinctrl_i2c0: i2c0grp { |
| fsl,pins = < |
| IMX8QM_HDMI_TX0_TS_SCL_DMA_I2C0_SCL 0x06000021 |
| IMX8QM_HDMI_TX0_TS_SDA_DMA_I2C0_SDA 0x06000021 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| IMX8QM_GPT0_CLK_DMA_I2C1_SCL 0x0600004c |
| IMX8QM_GPT0_CAPTURE_DMA_I2C1_SDA 0x0600004c |
| >; |
| }; |
| |
| pinctrl_i2c1_gpio: i2c1gpio-grp { |
| fsl,pins = < |
| IMX8QM_GPT0_CLK_LSIO_GPIO0_IO14 0xc600004c |
| IMX8QM_GPT0_CAPTURE_LSIO_GPIO0_IO15 0xc600004c |
| >; |
| }; |
| |
| pinctrl_adc0: adc0grp { |
| fsl,pins = < |
| IMX8QM_ADC_IN0_DMA_ADC0_IN0 0xc0000060 |
| >; |
| }; |
| |
| pinctrl_cm41_i2c: cm41i2cgrp { |
| fsl,pins = < |
| IMX8QM_M41_I2C0_SDA_M41_I2C0_SDA 0x0600004c |
| IMX8QM_M41_I2C0_SCL_M41_I2C0_SCL 0x0600004c |
| >; |
| }; |
| |
| pinctrl_fec1: fec1grp { |
| fsl,pins = < |
| IMX8QM_ENET0_MDC_CONN_ENET0_MDC 0x06000020 |
| IMX8QM_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020 |
| IMX8QM_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x06000020 |
| IMX8QM_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x06000020 |
| IMX8QM_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x06000020 |
| IMX8QM_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x06000020 |
| IMX8QM_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x06000020 |
| IMX8QM_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x06000020 |
| IMX8QM_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x06000020 |
| IMX8QM_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x06000020 |
| IMX8QM_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x06000020 |
| IMX8QM_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x06000020 |
| IMX8QM_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x06000020 |
| IMX8QM_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x06000020 |
| >; |
| }; |
| |
| pinctrl_lpspi2: lpspi2grp { |
| fsl,pins = < |
| IMX8QM_SPI2_SCK_DMA_SPI2_SCK 0x06000040 |
| IMX8QM_SPI2_SDO_DMA_SPI2_SDO 0x06000040 |
| IMX8QM_SPI2_SDI_DMA_SPI2_SDI 0x06000040 |
| >; |
| }; |
| |
| pinctrl_lpspi2_cs: lpspi2csgrp { |
| fsl,pins = < |
| IMX8QM_SPI2_CS0_LSIO_GPIO3_IO10 0x21 |
| >; |
| }; |
| |
| pinctrl_mipi0_lpi2c0: mipi0_lpi2c0grp { |
| fsl,pins = < |
| IMX8QM_MIPI_DSI0_I2C0_SCL_MIPI_DSI0_I2C0_SCL 0xc6000020 |
| IMX8QM_MIPI_DSI0_I2C0_SDA_MIPI_DSI0_I2C0_SDA 0xc6000020 |
| IMX8QM_MIPI_DSI0_GPIO0_01_LSIO_GPIO1_IO19 0x00000020 |
| >; |
| }; |
| |
| pinctrl_mipi1_lpi2c0: mipi1_lpi2c0grp { |
| fsl,pins = < |
| IMX8QM_MIPI_DSI1_I2C0_SCL_MIPI_DSI1_I2C0_SCL 0xc6000020 |
| IMX8QM_MIPI_DSI1_I2C0_SDA_MIPI_DSI1_I2C0_SDA 0xc6000020 |
| IMX8QM_MIPI_DSI1_GPIO0_01_LSIO_GPIO1_IO23 0x00000020 |
| >; |
| }; |
| |
| pinctrl_flexspi0: flexspi0grp { |
| fsl,pins = < |
| IMX8QM_QSPI0A_DATA0_LSIO_QSPI0A_DATA0 0x06000021 |
| IMX8QM_QSPI0A_DATA1_LSIO_QSPI0A_DATA1 0x06000021 |
| IMX8QM_QSPI0A_DATA2_LSIO_QSPI0A_DATA2 0x06000021 |
| IMX8QM_QSPI0A_DATA3_LSIO_QSPI0A_DATA3 0x06000021 |
| IMX8QM_QSPI0A_DQS_LSIO_QSPI0A_DQS 0x06000021 |
| IMX8QM_QSPI0A_SS0_B_LSIO_QSPI0A_SS0_B 0x06000021 |
| IMX8QM_QSPI0A_SS1_B_LSIO_QSPI0A_SS1_B 0x06000021 |
| IMX8QM_QSPI0A_SCLK_LSIO_QSPI0A_SCLK 0x06000021 |
| IMX8QM_QSPI0B_SCLK_LSIO_QSPI0B_SCLK 0x06000021 |
| IMX8QM_QSPI0B_DATA0_LSIO_QSPI0B_DATA0 0x06000021 |
| IMX8QM_QSPI0B_DATA1_LSIO_QSPI0B_DATA1 0x06000021 |
| IMX8QM_QSPI0B_DATA2_LSIO_QSPI0B_DATA2 0x06000021 |
| IMX8QM_QSPI0B_DATA3_LSIO_QSPI0B_DATA3 0x06000021 |
| IMX8QM_QSPI0B_DQS_LSIO_QSPI0B_DQS 0x06000021 |
| IMX8QM_QSPI0B_SS0_B_LSIO_QSPI0B_SS0_B 0x06000021 |
| IMX8QM_QSPI0B_SS1_B_LSIO_QSPI0B_SS1_B 0x06000021 |
| >; |
| }; |
| |
| pinctrl_fec2: fec2grp { |
| fsl,pins = < |
| IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD 0x000014a0 |
| IMX8QM_ENET1_RGMII_TX_CTL_CONN_ENET1_RGMII_TX_CTL 0x00000060 |
| IMX8QM_ENET1_RGMII_TXC_CONN_ENET1_RGMII_TXC 0x00000060 |
| IMX8QM_ENET1_RGMII_TXD0_CONN_ENET1_RGMII_TXD0 0x00000060 |
| IMX8QM_ENET1_RGMII_TXD1_CONN_ENET1_RGMII_TXD1 0x00000060 |
| IMX8QM_ENET1_RGMII_TXD2_CONN_ENET1_RGMII_TXD2 0x00000060 |
| IMX8QM_ENET1_RGMII_TXD3_CONN_ENET1_RGMII_TXD3 0x00000060 |
| IMX8QM_ENET1_RGMII_RXC_CONN_ENET1_RGMII_RXC 0x00000060 |
| IMX8QM_ENET1_RGMII_RX_CTL_CONN_ENET1_RGMII_RX_CTL 0x00000060 |
| IMX8QM_ENET1_RGMII_RXD0_CONN_ENET1_RGMII_RXD0 0x00000060 |
| IMX8QM_ENET1_RGMII_RXD1_CONN_ENET1_RGMII_RXD1 0x00000060 |
| IMX8QM_ENET1_RGMII_RXD2_CONN_ENET1_RGMII_RXD2 0x00000060 |
| IMX8QM_ENET1_RGMII_RXD3_CONN_ENET1_RGMII_RXD3 0x00000060 |
| >; |
| }; |
| |
| pinctrl_flexcan1: flexcan0grp { |
| fsl,pins = < |
| IMX8QM_FLEXCAN0_TX_DMA_FLEXCAN0_TX 0x21 |
| IMX8QM_FLEXCAN0_RX_DMA_FLEXCAN0_RX 0x21 |
| >; |
| }; |
| |
| pinctrl_flexcan2: flexcan1grp { |
| fsl,pins = < |
| IMX8QM_FLEXCAN1_TX_DMA_FLEXCAN1_TX 0x21 |
| IMX8QM_FLEXCAN1_RX_DMA_FLEXCAN1_RX 0x21 |
| >; |
| }; |
| |
| pinctrl_flexcan3: flexcan3grp { |
| fsl,pins = < |
| IMX8QM_FLEXCAN2_TX_DMA_FLEXCAN2_TX 0x21 |
| IMX8QM_FLEXCAN2_RX_DMA_FLEXCAN2_RX 0x21 |
| >; |
| }; |
| |
| pinctrl_lpuart0: lpuart0grp { |
| fsl,pins = < |
| IMX8QM_UART0_RX_DMA_UART0_RX 0x06000020 |
| IMX8QM_UART0_TX_DMA_UART0_TX 0x06000020 |
| >; |
| }; |
| |
| pinctrl_lpuart2: lpuart2grp { |
| fsl,pins = < |
| IMX8QM_UART0_RTS_B_DMA_UART2_RX 0x06000020 |
| IMX8QM_UART0_CTS_B_DMA_UART2_TX 0x06000020 |
| >; |
| }; |
| |
| pinctrl_lpuart3: lpuart3grp { |
| fsl,pins = < |
| IMX8QM_M41_GPIO0_00_DMA_UART3_RX 0x06000020 |
| IMX8QM_M41_GPIO0_01_DMA_UART3_TX 0x06000020 |
| >; |
| }; |
| |
| pinctrl_lvds0_lpi2c1: lvds0lpi2c1grp { |
| fsl,pins = < |
| IMX8QM_LVDS0_I2C1_SCL_LVDS0_I2C1_SCL 0xc600004c |
| IMX8QM_LVDS0_I2C1_SDA_LVDS0_I2C1_SDA 0xc600004c |
| >; |
| }; |
| |
| pinctrl_lvds1_lpi2c1: lvds1lpi2c1grp { |
| fsl,pins = < |
| IMX8QM_LVDS1_I2C1_SCL_LVDS1_I2C1_SCL 0xc600004c |
| IMX8QM_LVDS1_I2C1_SDA_LVDS1_I2C1_SDA 0xc600004c |
| >; |
| }; |
| |
| pinctrl_pwm_lvds0: pwmlvds0grp { |
| fsl,pins = < |
| IMX8QM_LVDS0_GPIO00_LVDS0_PWM0_OUT 0x00000020 |
| >; |
| }; |
| |
| pinctrl_pwm_lvds1: pwmlvds1grp { |
| fsl,pins = < |
| IMX8QM_LVDS1_GPIO00_LVDS1_PWM0_OUT 0x00000020 |
| >; |
| }; |
| |
| pinctrl_sai0: sai0grp { |
| fsl,pins = < |
| IMX8QM_SPI0_CS1_AUD_SAI0_TXC 0x0600004c |
| IMX8QM_SPI2_CS1_AUD_SAI0_TXFS 0x0600004c |
| IMX8QM_SAI1_RXFS_AUD_SAI0_RXD 0x0600004c |
| IMX8QM_SAI1_RXC_AUD_SAI0_TXD 0x0600006c |
| >; |
| }; |
| |
| pinctrl_sai1: sai1grp { |
| fsl,pins = < |
| IMX8QM_SAI1_RXD_AUD_SAI1_RXD 0x06000040 |
| IMX8QM_SAI1_TXFS_AUD_SAI1_TXFS 0x06000040 |
| IMX8QM_SAI1_TXD_AUD_SAI1_TXD 0x06000060 |
| IMX8QM_SAI1_TXC_AUD_SAI1_TXC 0x06000040 |
| >; |
| }; |
| |
| pinctrl_typec: typecgrp { |
| fsl,pins = < |
| IMX8QM_QSPI1A_DATA0_LSIO_GPIO4_IO26 0x00000021 |
| >; |
| }; |
| |
| pinctrl_typec_mux: typecmuxgrp { |
| fsl,pins = < |
| IMX8QM_QSPI1A_SS0_B_LSIO_GPIO4_IO19 0x60 |
| IMX8QM_USB_SS3_TC3_LSIO_GPIO4_IO06 0x60 |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041 |
| IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021 |
| IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021 |
| IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021 |
| IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021 |
| IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021 |
| IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021 |
| IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021 |
| IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021 |
| IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021 |
| IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000041 |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = < |
| IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041 |
| IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021 |
| IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021 |
| IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021 |
| IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021 |
| IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021 |
| IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021 |
| >; |
| }; |
| }; |
