| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright 2021 NXP |
| */ |
| |
| #include <dt-bindings/clock/imx8ulp-clock.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/power/imx8ulp-power.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| #include "imx8ulp-pinfunc.h" |
| |
| / { |
| interrupt-parent = <&gic>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| aliases { |
| ethernet0 = &fec; |
| gpio0 = &gpiod; |
| gpio1 = &gpioe; |
| gpio2 = &gpiof; |
| mmc0 = &usdhc0; |
| mmc1 = &usdhc1; |
| mmc2 = &usdhc2; |
| serial0 = &lpuart4; |
| serial1 = &lpuart5; |
| serial2 = &lpuart6; |
| serial3 = &lpuart7; |
| }; |
| |
| cpus { |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| A35_0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a35"; |
| reg = <0x0 0x0>; |
| enable-method = "psci"; |
| next-level-cache = <&A35_L2>; |
| cpu-idle-states = <&cpu_sleep>; |
| }; |
| |
| A35_1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a35"; |
| reg = <0x0 0x1>; |
| enable-method = "psci"; |
| next-level-cache = <&A35_L2>; |
| cpu-idle-states = <&cpu_sleep>; |
| }; |
| |
| A35_L2: l2-cache0 { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| |
| idle-states { |
| entry-method = "psci"; |
| |
| cpu_sleep: cpu-sleep { |
| compatible = "arm,idle-state"; |
| arm,psci-suspend-param = <0x0>; |
| local-timer-stop; |
| entry-latency-us = <1000>; |
| exit-latency-us = <700>; |
| min-residency-us = <2700>; |
| }; |
| }; |
| }; |
| |
| gic: interrupt-controller@2d400000 { |
| compatible = "arm,gic-v3"; |
| reg = <0x0 0x2d400000 0 0x10000>, /* GIC Dist */ |
| <0x0 0x2d440000 0 0xc0000>; /* GICR (RD_base + SGI_base) */ |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a35-pmu"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_PPI 7 |
| (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; |
| interrupt-affinity = <&A35_0>, <&A35_1>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| thermal-zones { |
| cpu-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <2000>; |
| thermal-sensors = <&scmi_sensor 0>; |
| |
| trips { |
| cpu_alert0: trip0 { |
| temperature = <85000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu_crit0: trip1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */ |
| <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */ |
| <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */ |
| <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */ |
| }; |
| |
| frosc: clock-frosc { |
| compatible = "fixed-clock"; |
| clock-frequency = <192000000>; |
| clock-output-names = "frosc"; |
| #clock-cells = <0>; |
| }; |
| |
| lposc: clock-lposc { |
| compatible = "fixed-clock"; |
| clock-frequency = <1000000>; |
| clock-output-names = "lposc"; |
| #clock-cells = <0>; |
| }; |
| |
| rosc: clock-rosc { |
| compatible = "fixed-clock"; |
| clock-frequency = <32768>; |
| clock-output-names = "rosc"; |
| #clock-cells = <0>; |
| }; |
| |
| sosc: clock-sosc { |
| compatible = "fixed-clock"; |
| clock-frequency = <24000000>; |
| clock-output-names = "sosc"; |
| #clock-cells = <0>; |
| }; |
| |
| sram@2201f000 { |
| compatible = "mmio-sram"; |
| reg = <0x0 0x2201f000 0x0 0x1000>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x0 0x2201f000 0x1000>; |
| |
| scmi_buf: scmi-sram-section@0 { |
| compatible = "arm,scmi-shmem"; |
| reg = <0x0 0x400>; |
| }; |
| }; |
| |
| firmware { |
| scmi { |
| compatible = "arm,scmi-smc"; |
| arm,smc-id = <0xc20000fe>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| shmem = <&scmi_buf>; |
| |
| scmi_devpd: protocol@11 { |
| reg = <0x11>; |
| #power-domain-cells = <1>; |
| }; |
| |
| scmi_sensor: protocol@15 { |
| reg = <0x15>; |
| #thermal-sensor-cells = <1>; |
| }; |
| }; |
| }; |
| |
| cm33: remoteproc-cm33 { |
| compatible = "fsl,imx8ulp-cm33"; |
| status = "disabled"; |
| }; |
| |
| soc: soc@0 { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x0 0x0 0x40000000>, |
| <0x60000000 0x0 0x60000000 0x1000000>; |
| |
| s4muap: mailbox@27020000 { |
| compatible = "fsl,imx8ulp-mu-s4"; |
| reg = <0x27020000 0x10000>; |
| interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| #mbox-cells = <2>; |
| }; |
| |
| per_bridge3: bus@29000000 { |
| compatible = "simple-bus"; |
| reg = <0x29000000 0x800000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| mu: mailbox@29220000 { |
| compatible = "fsl,imx8ulp-mu"; |
| reg = <0x29220000 0x10000>; |
| interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; |
| #mbox-cells = <2>; |
| status = "disabled"; |
| }; |
| |
| mu3: mailbox@29230000 { |
| compatible = "fsl,imx8ulp-mu"; |
| reg = <0x29230000 0x10000>; |
| interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc3 IMX8ULP_CLK_MU3_A>; |
| #mbox-cells = <2>; |
| status = "disabled"; |
| }; |
| |
| wdog3: watchdog@292a0000 { |
| compatible = "fsl,imx8ulp-wdt", "fsl,imx7ulp-wdt"; |
| reg = <0x292a0000 0x10000>; |
| interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc3 IMX8ULP_CLK_WDOG3>; |
| assigned-clocks = <&pcc3 IMX8ULP_CLK_WDOG3>; |
| assigned-clock-parents = <&cgc1 IMX8ULP_CLK_SOSC_DIV2>; |
| timeout-sec = <40>; |
| }; |
| |
| cgc1: clock-controller@292c0000 { |
| compatible = "fsl,imx8ulp-cgc1"; |
| reg = <0x292c0000 0x10000>; |
| #clock-cells = <1>; |
| }; |
| |
| pcc3: clock-controller@292d0000 { |
| compatible = "fsl,imx8ulp-pcc3"; |
| reg = <0x292d0000 0x10000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| crypto: crypto@292e0000 { |
| compatible = "fsl,sec-v4.0"; |
| reg = <0x292e0000 0x10000>; |
| ranges = <0 0x292e0000 0x10000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| sec_jr0: jr@1000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x1000 0x1000>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| sec_jr1: jr@2000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x2000 0x1000>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| sec_jr2: jr@3000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x3000 0x1000>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| sec_jr3: jr@4000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x4000 0x1000>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| tpm5: tpm@29340000 { |
| compatible = "fsl,imx8ulp-tpm", "fsl,imx7ulp-tpm"; |
| reg = <0x29340000 0x1000>; |
| interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc3 IMX8ULP_CLK_TPM5>, |
| <&pcc3 IMX8ULP_CLK_TPM5>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| lpi2c4: i2c@29370000 { |
| compatible = "fsl,imx8ulp-lpi2c", "fsl,imx7ulp-lpi2c"; |
| reg = <0x29370000 0x10000>; |
| interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc3 IMX8ULP_CLK_LPI2C4>, |
| <&pcc3 IMX8ULP_CLK_LPI2C4>; |
| clock-names = "per", "ipg"; |
| assigned-clocks = <&pcc3 IMX8ULP_CLK_LPI2C4>; |
| assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| |
| lpi2c5: i2c@29380000 { |
| compatible = "fsl,imx8ulp-lpi2c", "fsl,imx7ulp-lpi2c"; |
| reg = <0x29380000 0x10000>; |
| interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc3 IMX8ULP_CLK_LPI2C5>, |
| <&pcc3 IMX8ULP_CLK_LPI2C5>; |
| clock-names = "per", "ipg"; |
| assigned-clocks = <&pcc3 IMX8ULP_CLK_LPI2C5>; |
| assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| |
| lpuart4: serial@29390000 { |
| compatible = "fsl,imx8ulp-lpuart", "fsl,imx7ulp-lpuart"; |
| reg = <0x29390000 0x1000>; |
| interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc3 IMX8ULP_CLK_LPUART4>; |
| clock-names = "ipg"; |
| status = "disabled"; |
| }; |
| |
| lpuart5: serial@293a0000 { |
| compatible = "fsl,imx8ulp-lpuart", "fsl,imx7ulp-lpuart"; |
| reg = <0x293a0000 0x1000>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc3 IMX8ULP_CLK_LPUART5>; |
| clock-names = "ipg"; |
| status = "disabled"; |
| }; |
| |
| lpspi4: spi@293b0000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx8ulp-spi", "fsl,imx7ulp-spi"; |
| reg = <0x293b0000 0x10000>; |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc3 IMX8ULP_CLK_LPSPI4>, |
| <&pcc3 IMX8ULP_CLK_LPSPI4>; |
| clock-names = "per", "ipg"; |
| assigned-clocks = <&pcc3 IMX8ULP_CLK_LPSPI4>; |
| assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| |
| lpspi5: spi@293c0000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx8ulp-spi", "fsl,imx7ulp-spi"; |
| reg = <0x293c0000 0x10000>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc3 IMX8ULP_CLK_LPSPI5>, |
| <&pcc3 IMX8ULP_CLK_LPSPI5>; |
| clock-names = "per", "ipg"; |
| assigned-clocks = <&pcc3 IMX8ULP_CLK_LPSPI5>; |
| assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| per_bridge4: bus@29800000 { |
| compatible = "simple-bus"; |
| reg = <0x29800000 0x800000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| pcc4: clock-controller@29800000 { |
| compatible = "fsl,imx8ulp-pcc4"; |
| reg = <0x29800000 0x10000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| flexspi2: spi@29810000 { |
| compatible = "nxp,imx8ulp-fspi"; |
| reg = <0x29810000 0x10000>, <0x60000000 0x10000000>; |
| reg-names = "fspi_base", "fspi_mmap"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc4 IMX8ULP_CLK_FLEXSPI2>, |
| <&pcc4 IMX8ULP_CLK_FLEXSPI2>; |
| clock-names = "fspi_en", "fspi"; |
| assigned-clocks = <&pcc4 IMX8ULP_CLK_FLEXSPI2>; |
| assigned-clock-parents = <&cgc1 IMX8ULP_CLK_SPLL3_PFD3_DIV2>; |
| status = "disabled"; |
| }; |
| |
| lpi2c6: i2c@29840000 { |
| compatible = "fsl,imx8ulp-lpi2c", "fsl,imx7ulp-lpi2c"; |
| reg = <0x29840000 0x10000>; |
| interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc4 IMX8ULP_CLK_LPI2C6>, |
| <&pcc4 IMX8ULP_CLK_LPI2C6>; |
| clock-names = "per", "ipg"; |
| assigned-clocks = <&pcc4 IMX8ULP_CLK_LPI2C6>; |
| assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| |
| lpi2c7: i2c@29850000 { |
| compatible = "fsl,imx8ulp-lpi2c", "fsl,imx7ulp-lpi2c"; |
| reg = <0x29850000 0x10000>; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc4 IMX8ULP_CLK_LPI2C7>, |
| <&pcc4 IMX8ULP_CLK_LPI2C7>; |
| clock-names = "per", "ipg"; |
| assigned-clocks = <&pcc4 IMX8ULP_CLK_LPI2C7>; |
| assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| |
| lpuart6: serial@29860000 { |
| compatible = "fsl,imx8ulp-lpuart", "fsl,imx7ulp-lpuart"; |
| reg = <0x29860000 0x1000>; |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc4 IMX8ULP_CLK_LPUART6>; |
| clock-names = "ipg"; |
| status = "disabled"; |
| }; |
| |
| lpuart7: serial@29870000 { |
| compatible = "fsl,imx8ulp-lpuart", "fsl,imx7ulp-lpuart"; |
| reg = <0x29870000 0x1000>; |
| interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc4 IMX8ULP_CLK_LPUART7>; |
| clock-names = "ipg"; |
| status = "disabled"; |
| }; |
| |
| iomuxc1: pinctrl@298c0000 { |
| compatible = "fsl,imx8ulp-iomuxc1"; |
| reg = <0x298c0000 0x10000>; |
| }; |
| |
| usdhc0: mmc@298d0000 { |
| compatible = "fsl,imx8ulp-usdhc", "fsl,imx8mm-usdhc"; |
| reg = <0x298d0000 0x10000>; |
| interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>, |
| <&cgc1 IMX8ULP_CLK_XBAR_AD_DIVPLAT>, |
| <&pcc4 IMX8ULP_CLK_USDHC0>; |
| clock-names = "ipg", "ahb", "per"; |
| power-domains = <&scmi_devpd IMX8ULP_PD_USDHC0>; |
| assigned-clocks = <&cgc1 IMX8ULP_CLK_SPLL3_PFD3_DIV1>, |
| <&pcc4 IMX8ULP_CLK_USDHC0>; |
| assigned-clock-parents = <0>, <&cgc1 IMX8ULP_CLK_SPLL3_PFD3_DIV1>; |
| assigned-clock-rates = <389283840>, <389283840>; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step = <2>; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc1: mmc@298e0000 { |
| compatible = "fsl,imx8ulp-usdhc", "fsl,imx8mm-usdhc"; |
| reg = <0x298e0000 0x10000>; |
| interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>, |
| <&cgc1 IMX8ULP_CLK_NIC_PER_DIVPLAT>, |
| <&pcc4 IMX8ULP_CLK_USDHC1>; |
| clock-names = "ipg", "ahb", "per"; |
| power-domains = <&scmi_devpd IMX8ULP_PD_USDHC1>; |
| assigned-clocks = <&cgc1 IMX8ULP_CLK_SPLL3_PFD3_DIV2>, |
| <&pcc4 IMX8ULP_CLK_USDHC1>; |
| assigned-clock-parents = <0>, <&cgc1 IMX8ULP_CLK_SPLL3_PFD3_DIV2>; |
| assigned-clock-rates = <194641920>, <194641920>; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step = <2>; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc2: mmc@298f0000 { |
| compatible = "fsl,imx8ulp-usdhc", "fsl,imx8mm-usdhc"; |
| reg = <0x298f0000 0x10000>; |
| interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>, |
| <&cgc1 IMX8ULP_CLK_NIC_PER_DIVPLAT>, |
| <&pcc4 IMX8ULP_CLK_USDHC2>; |
| clock-names = "ipg", "ahb", "per"; |
| power-domains = <&scmi_devpd IMX8ULP_PD_USDHC2_USB1>; |
| assigned-clocks = <&cgc1 IMX8ULP_CLK_SPLL3_PFD3_DIV2>, |
| <&pcc4 IMX8ULP_CLK_USDHC2>; |
| assigned-clock-parents = <0>, <&cgc1 IMX8ULP_CLK_SPLL3_PFD3_DIV2>; |
| assigned-clock-rates = <194641920>, <194641920>; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step = <2>; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usbotg1: usb@29900000 { |
| compatible = "fsl,imx8ulp-usb", "fsl,imx7ulp-usb", "fsl,imx6ul-usb"; |
| reg = <0x29900000 0x200>; |
| interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc4 IMX8ULP_CLK_USB0>; |
| power-domains = <&scmi_devpd IMX8ULP_PD_USB0>; |
| phys = <&usbphy1>; |
| fsl,usbmisc = <&usbmisc1 0>; |
| ahb-burst-config = <0x0>; |
| tx-burst-size-dword = <0x8>; |
| rx-burst-size-dword = <0x8>; |
| status = "disabled"; |
| }; |
| |
| usbmisc1: usbmisc@29900200 { |
| compatible = "fsl,imx8ulp-usbmisc", "fsl,imx7d-usbmisc", |
| "fsl,imx6q-usbmisc"; |
| reg = <0x29900200 0x200>; |
| #index-cells = <1>; |
| status = "disabled"; |
| }; |
| |
| usbphy1: usb-phy@29910000 { |
| compatible = "fsl,imx8ulp-usbphy", "fsl,imx7ulp-usbphy"; |
| reg = <0x29910000 0x10000>; |
| interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc4 IMX8ULP_CLK_USB0_PHY>; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| usbotg2: usb@29920000 { |
| compatible = "fsl,imx8ulp-usb", "fsl,imx7ulp-usb", "fsl,imx6ul-usb"; |
| reg = <0x29920000 0x200>; |
| interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc4 IMX8ULP_CLK_USB1>; |
| power-domains = <&scmi_devpd IMX8ULP_PD_USDHC2_USB1>; |
| phys = <&usbphy2>; |
| fsl,usbmisc = <&usbmisc2 0>; |
| ahb-burst-config = <0x0>; |
| tx-burst-size-dword = <0x8>; |
| rx-burst-size-dword = <0x8>; |
| status = "disabled"; |
| }; |
| |
| usbmisc2: usbmisc@29920200 { |
| compatible = "fsl,imx8ulp-usbmisc", "fsl,imx7d-usbmisc", |
| "fsl,imx6q-usbmisc"; |
| reg = <0x29920200 0x200>; |
| #index-cells = <1>; |
| status = "disabled"; |
| }; |
| |
| usbphy2: usb-phy@29930000 { |
| compatible = "fsl,imx8ulp-usbphy", "fsl,imx7ulp-usbphy"; |
| reg = <0x29930000 0x10000>; |
| interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pcc4 IMX8ULP_CLK_USB1_PHY>; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| fec: ethernet@29950000 { |
| compatible = "fsl,imx8ulp-fec", "fsl,imx6ul-fec", "fsl,imx6q-fec"; |
| reg = <0x29950000 0x10000>; |
| interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "int0"; |
| fsl,num-tx-queues = <1>; |
| fsl,num-rx-queues = <1>; |
| status = "disabled"; |
| }; |
| }; |
| |
| gpioe: gpio@2d000000 { |
| compatible = "fsl,imx8ulp-gpio"; |
| reg = <0x2d000000 0x1000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pcc4 IMX8ULP_CLK_RGPIOE>, |
| <&pcc4 IMX8ULP_CLK_PCTLE>; |
| clock-names = "gpio", "port"; |
| gpio-ranges = <&iomuxc1 0 32 24>; |
| }; |
| |
| gpiof: gpio@2d010000 { |
| compatible = "fsl,imx8ulp-gpio"; |
| reg = <0x2d010000 0x1000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pcc4 IMX8ULP_CLK_RGPIOF>, |
| <&pcc4 IMX8ULP_CLK_PCTLF>; |
| clock-names = "gpio", "port"; |
| gpio-ranges = <&iomuxc1 0 64 32>; |
| }; |
| |
| per_bridge5: bus@2d800000 { |
| compatible = "simple-bus"; |
| reg = <0x2d800000 0x800000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| cgc2: clock-controller@2da60000 { |
| compatible = "fsl,imx8ulp-cgc2"; |
| reg = <0x2da60000 0x10000>; |
| #clock-cells = <1>; |
| }; |
| |
| pcc5: clock-controller@2da70000 { |
| compatible = "fsl,imx8ulp-pcc5"; |
| reg = <0x2da70000 0x10000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| }; |
| |
| gpiod: gpio@2e200000 { |
| compatible = "fsl,imx8ulp-gpio"; |
| reg = <0x2e200000 0x1000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| clocks = <&pcc5 IMX8ULP_CLK_RGPIOD>, |
| <&pcc5 IMX8ULP_CLK_RGPIOD>; |
| clock-names = "gpio", "port"; |
| gpio-ranges = <&iomuxc1 0 0 24>; |
| }; |
| }; |
| }; |
