| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2019, Intel Corporation |
| */ |
| #include "socfpga_agilex.dtsi" |
| |
| / { |
| model = "SoCFPGA Agilex SoCDK"; |
| compatible = "intel,socfpga-agilex-socdk", "intel,socfpga-agilex"; |
| |
| aliases { |
| serial0 = &uart0; |
| ethernet0 = &gmac0; |
| ethernet1 = &gmac1; |
| ethernet2 = &gmac2; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| led0 { |
| label = "hps_led0"; |
| gpios = <&portb 20 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| led1 { |
| label = "hps_led1"; |
| gpios = <&portb 19 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| led2 { |
| label = "hps_led2"; |
| gpios = <&portb 21 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| /* We expect the bootloader to fill in the reg */ |
| reg = <0 0x80000000 0 0>; |
| }; |
| }; |
| |
| &gpio1 { |
| status = "okay"; |
| }; |
| |
| &gmac2 { |
| status = "okay"; |
| phy-mode = "rgmii"; |
| phy-handle = <&phy0>; |
| |
| max-frame-size = <9000>; |
| |
| mdio0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,dwmac-mdio"; |
| phy0: ethernet-phy@0 { |
| reg = <4>; |
| |
| txd0-skew-ps = <0>; /* -420ps */ |
| txd1-skew-ps = <0>; /* -420ps */ |
| txd2-skew-ps = <0>; /* -420ps */ |
| txd3-skew-ps = <0>; /* -420ps */ |
| rxd0-skew-ps = <420>; /* 0ps */ |
| rxd1-skew-ps = <420>; /* 0ps */ |
| rxd2-skew-ps = <420>; /* 0ps */ |
| rxd3-skew-ps = <420>; /* 0ps */ |
| txen-skew-ps = <0>; /* -420ps */ |
| txc-skew-ps = <900>; /* 0ps */ |
| rxdv-skew-ps = <420>; /* 0ps */ |
| rxc-skew-ps = <1680>; /* 780ps */ |
| }; |
| }; |
| }; |
| |
| &nand { |
| status = "okay"; |
| |
| flash@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0>; |
| nand-bus-width = <16>; |
| |
| partition@0 { |
| label = "u-boot"; |
| reg = <0 0x200000>; |
| }; |
| partition@200000 { |
| label = "root"; |
| reg = <0x200000 0x3fe00000>; |
| }; |
| }; |
| }; |
| |
| &osc1 { |
| clock-frequency = <25000000>; |
| }; |
| |
| &uart0 { |
| status = "okay"; |
| }; |
| |
| &usb0 { |
| status = "okay"; |
| disable-over-current; |
| }; |
| |
| &watchdog0 { |
| status = "okay"; |
| }; |