arch/arm64/boot/dts/marvell/cn9132-db.dtsi

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (C) 2020 Marvell International Ltd.
 *
 * Device tree for the CN9132-DB board.
 */

#include "cn9131-db.dtsi"

/ {
	compatible = "marvell,cn9132", "marvell,cn9131", "marvell,cn9130",
		     "marvell,armada-ap807-quad", "marvell,armada-ap807";

	aliases {
		gpio5 = &cp2_gpio1;
		gpio6 = &cp2_gpio2;
		ethernet5 = &cp2_eth0;
	};

	cp2_reg_usb3_vbus0: regulator-7 {
		compatible = "regulator-fixed";
		regulator-name = "cp2-xhci0-vbus";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		enable-active-high;
		gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>;
	};

	cp2_usb3_0_phy0: usb-phy-4 {
		compatible = "usb-nop-xceiv";
		vcc-supply = <&cp2_reg_usb3_vbus0>;
	};

	cp2_reg_usb3_vbus1: regulator-8 {
		compatible = "regulator-fixed";
		regulator-name = "cp2-xhci1-vbus";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		enable-active-high;
		gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>;
	};

	cp2_usb3_0_phy1: usb-phy-5 {
		compatible = "usb-nop-xceiv";
		vcc-supply = <&cp2_reg_usb3_vbus1>;
	};

	cp2_reg_sd_vccq: regulator-9 {
		compatible = "regulator-gpio";
		regulator-name = "cp2_sd_vcc";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <3300000>;
		gpios = <&cp2_gpio2 17 GPIO_ACTIVE_HIGH>;
		states = <1800000 0x1 3300000 0x0>;
	};

	cp2_sfp_eth0: sfp-eth-3 {
		compatible = "sff,sfp";
		i2c-bus = <&cp2_sfpp0_i2c>;
		los-gpios = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>;
		mod-def0-gpios = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>;
		tx-disable-gpios = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>;
		tx-fault-gpios = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>;
		/*
		 * SFP cages are unconnected on early PCBs because of an the I2C
		 * lanes not being connected. Prevent the port for being
		 * unusable by disabling the SFP node.
		 */
		status = "disabled";
	};
};

/*
 * Instantiate the second slave CP115
 */

#define CP11X_NAME		cp2
#define CP11X_BASE		f6000000
#define CP11X_PCIEx_MEM_BASE(iface) (0xe5000000 + (iface * 0x1000000))
#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
#define CP11X_PCIE0_BASE	f6600000
#define CP11X_PCIE1_BASE	f6620000
#define CP11X_PCIE2_BASE	f6640000

#include "armada-cp115.dtsi"

#undef CP11X_NAME
#undef CP11X_BASE
#undef CP11X_PCIEx_MEM_BASE
#undef CP11X_PCIEx_MEM_SIZE
#undef CP11X_PCIE0_BASE
#undef CP11X_PCIE1_BASE
#undef CP11X_PCIE2_BASE

&cp2_crypto {
	status = "disabled";
};

&cp2_ethernet {
	status = "okay";
};

/* SLM-1521-V2, CON9 */
&cp2_eth0 {
	status = "disabled";
	phy-mode = "10gbase-r";
	/* Generic PHY, providing serdes lanes */
	phys = <&cp2_comphy4 0>;
	managed = "in-band-status";
	sfp = <&cp2_sfp_eth0>;
};

&cp2_gpio1 {
	status = "okay";
};

&cp2_gpio2 {
	status = "okay";
};

&cp2_i2c0 {
	clock-frequency = <100000>;

	/* SLM-1521-V2 - U3 */
	i2c-mux@72 {
		compatible = "nxp,pca9544";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0x72>;
		cp2_sfpp0_i2c: i2c@0 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0>;
		};

		i2c@1 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <1>;
			/* U12 */
			cp2_module_expander1: pca9555@21 {
				compatible = "nxp,pca9555";
				pinctrl-names = "default";
				gpio-controller;
				#gpio-cells = <2>;
				reg = <0x21>;
			};
		};
	};
};

/* SLM-1521-V2, CON6 */
&cp2_pcie0 {
	status = "okay";
	num-lanes = <2>;
	num-viewport = <8>;
	/* Generic PHY, providing serdes lanes */
	phys = <&cp2_comphy0 0
		&cp2_comphy1 0>;
};

/* SLM-1521-V2, CON8 */
&cp2_pcie2 {
	status = "okay";
	num-lanes = <1>;
	num-viewport = <8>;
	/* Generic PHY, providing serdes lanes */
	phys = <&cp2_comphy5 2>;
};

&cp2_sata0 {
	status = "okay";

	/* SLM-1521-V2, CON4 */
	sata-port@0 {
		/* Generic PHY, providing serdes lanes */
		phys = <&cp2_comphy2 0>;
	};
};

/* CON 2 on SLM-1683 - microSD */
&cp2_sdhci0 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&cp2_sdhci_pins>;
	bus-width = <4>;
	cd-gpios = <&cp2_gpio2 23 GPIO_ACTIVE_LOW>;
	vqmmc-supply = <&cp2_reg_sd_vccq>;
};

&cp2_syscon0 {
	cp2_pinctrl: pinctrl {
		compatible = "marvell,cp115-standalone-pinctrl";

		cp2_i2c0_pins: cp2-i2c-pins-0 {
			marvell,pins = "mpp37", "mpp38";
			marvell,function = "i2c0";
		};
		cp2_sdhci_pins: cp2-sdhi-pins-0 {
			marvell,pins = "mpp56", "mpp57", "mpp58",
				       "mpp59", "mpp60", "mpp61";
			marvell,function = "sdio";
		};
	};
};

&cp2_utmi {
	status = "okay";
};

&cp2_usb3_0 {
	status = "okay";
	usb-phy = <&cp2_usb3_0_phy0>;
	phys = <&cp2_utmi0>;
	phy-names = "usb";
	dr_mode = "host";
};

/* SLM-1521-V2, CON11 */
&cp2_usb3_1 {
	status = "okay";
	usb-phy = <&cp2_usb3_0_phy1>;
	/* Generic PHY, providing serdes lanes */
	phys = <&cp2_comphy3 1>, <&cp2_utmi1>;
	phy-names = "usb", "utmi";
	dr_mode = "host";
};