arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts - linux - Git at Google

 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2021 Stephan Gerhold
  */

 /dts-v1/;

 #include "msm8916-pm8916.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/sound/apq8016-lpass.h>

 /*
  * Note: The original firmware from Huawei can only boot 32-bit kernels.
  * To boot this device tree using arm64 it is necessary to flash 64-bit TZ/HYP
  * firmware (e.g. taken from the DragonBoard 410c).
  * See https://wiki.postmarketos.org/wiki/Huawei_Ascend_G7_(huawei-g7)
  * for suggested installation instructions.
  */

 / {
 	model = "Huawei Ascend G7";
 	compatible = "huawei,g7", "qcom,msm8916";
 	chassis-type = "handset";

 	aliases {
 		mmc0 = &sdhc_1; /* eMMC */
 		mmc1 = &sdhc_2; /* SD card */
 		serial0 = &blsp_uart2;
 	};

 	chosen {
 		stdout-path = "serial0";
 	};

 	gpio-keys {
 		compatible = "gpio-keys";

 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_keys_default>;

 		label = "GPIO Buttons";

 		button-volume-up {
 			label = "Volume Up";
 			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 	};

 	leds {
 		compatible = "gpio-leds";

 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_leds_default>;

 		led-0 {
 			gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
 			color = <LED_COLOR_ID_RED>;
 			default-state = "off";
 			function = LED_FUNCTION_INDICATOR;
 		};

 		led-1 {
 			gpios = <&tlmm 9 GPIO_ACTIVE_HIGH>;
 			color = <LED_COLOR_ID_GREEN>;
 			default-state = "off";
 			function = LED_FUNCTION_INDICATOR;
 		};

 		led-2 {
 			gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
 			color = <LED_COLOR_ID_BLUE>;
 			default-state = "off";
 			function = LED_FUNCTION_INDICATOR;
 		};
 	};

 	usb_id: usb-id {
 		compatible = "linux,extcon-usb-gpio";
 		id-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&usb_id_default>;
 	};
 };

 &blsp_i2c2 {
 	status = "okay";

 	magnetometer@c {
 		compatible = "asahi-kasei,ak09911";
 		reg = <0x0c>;

 		vdd-supply = <&pm8916_l17>;
 		vid-supply = <&pm8916_l6>;

 		reset-gpios = <&tlmm 36 GPIO_ACTIVE_LOW>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&mag_reset_default>;
 	};

 	accelerometer@1e {
 		compatible = "kionix,kx023-1025";
 		reg = <0x1e>;

 		interrupt-parent = <&tlmm>;
 		interrupts = <115 IRQ_TYPE_EDGE_RISING>;

 		vdd-supply = <&pm8916_l17>;
 		vddio-supply = <&pm8916_l6>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&accel_irq_default>;

 		mount-matrix = "-1", "0", "0",
 				"0", "1", "0",
 				"0", "0", "1";
 	};

 	proximity@39 {
 		compatible = "avago,apds9930";
 		reg = <0x39>;

 		interrupt-parent = <&tlmm>;
 		interrupts = <113 IRQ_TYPE_EDGE_FALLING>;

 		vdd-supply = <&pm8916_l17>;
 		vddio-supply = <&pm8916_l6>;

 		led-max-microamp = <100000>;
 		amstaos,proximity-diodes = <1>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&prox_irq_default>;
 	};

 	regulator@3e {
 		compatible = "ti,tps65132";
 		reg = <0x3e>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&reg_lcd_en_default>;

 		reg_lcd_pos: outp {
 			regulator-name = "outp";
 			regulator-min-microvolt = <5400000>;
 			regulator-max-microvolt = <5400000>;
 			enable-gpios = <&tlmm 97 GPIO_ACTIVE_HIGH>;
 			regulator-active-discharge = <1>;
 		};

 		reg_lcd_neg: outn {
 			regulator-name = "outn";
 			regulator-min-microvolt = <5400000>;
 			regulator-max-microvolt = <5400000>;
 			enable-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
 			regulator-active-discharge = <1>;
 		};
 	};
 };

 &blsp_i2c5 {
 	status = "okay";

 	rmi4@70 {
 		compatible = "syna,rmi4-i2c";
 		reg = <0x70>;
 		#address-cells = <1>;
 		#size-cells = <0>;

 		interrupt-parent = <&tlmm>;
 		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;

 		vdd-supply = <&pm8916_l17>;
 		vio-supply = <&pm8916_l16>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&ts_irq_default>;

 		syna,startup-delay-ms = <100>;

 		rmi4-f01@1 {
 			reg = <0x1>;
 			syna,nosleep-mode = <1>; /* Allow sleeping */
 		};

 		rmi4-f11@11 {
 			reg = <0x11>;
 			syna,sensor-type = <1>; /* Touchscreen */
 		};
 	};
 };

 &blsp_i2c6 {
 	status = "okay";

 	nfc@28 {
 		compatible = "nxp,pn547", "nxp,nxp-nci-i2c";
 		reg = <0x28>;

 		interrupt-parent = <&tlmm>;
 		interrupts = <21 IRQ_TYPE_EDGE_RISING>;

 		enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
 		firmware-gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&nfc_default>;
 	};
 };

 &blsp_uart2 {
 	status = "okay";
 };

 &lpass {
 	status = "okay";
 };

 &lpass_codec {
 	status = "okay";
 };

 &pm8916_codec {
 	status = "okay";
 	qcom,micbias-lvl = <2800>;
 	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
 	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
 	qcom,hphl-jack-type-normally-open;
 };

 &pm8916_l8 {
 	regulator-min-microvolt = <2950000>;
 	regulator-max-microvolt = <2950000>;
 };

 &pm8916_resin {
 	status = "okay";
 	linux,code = <KEY_VOLUMEDOWN>;
 };

 &pm8916_rpm_regulators {
 	pm8916_l16: l16 {
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 	};

 	pm8916_l17: l17 {
 		regulator-min-microvolt = <2850000>;
 		regulator-max-microvolt = <2850000>;
 	};
 };

 &pm8916_vib {
 	status = "okay";
 };

 &sdhc_1 {
 	status = "okay";
 };

 &sdhc_2 {
 	status = "okay";

 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
 	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;

 	/*
 	 * The Huawei device tree sets cd-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>.
 	 * However, gpio38 does not change its state when inserting/removing the
 	 * SD card, it's just low all the time. The Huawei kernel seems to use
 	 * polling for SD card detection instead.
 	 *
 	 * However, looking closer at the GPIO debug output it turns out that
 	 * gpio56 switches its state when inserting/removing the SD card.
 	 * It behaves just like gpio38 normally does. Usually GPIO56 is used as
 	 * "UIM2_PRESENT", i.e. to check if a second SIM card is inserted.
 	 * Maybe Huawei decided to replace the second SIM card slot with the
 	 * SD card slot and forgot to re-route to gpio38.
 	 */
 	cd-gpios = <&tlmm 56 GPIO_ACTIVE_LOW>;
 };

 &sound {
 	status = "okay";

 	model = "msm8916";
 	audio-routing =
 		"AMIC1", "MIC BIAS External1",
 		"AMIC2", "MIC BIAS External2",
 		"AMIC3", "MIC BIAS External1";

 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cdc_pdm_default>;
 	pinctrl-1 = <&cdc_pdm_sleep>;

 	primary-dai-link {
 		link-name = "WCD";
 		cpu {
 			sound-dai = <&lpass MI2S_PRIMARY>;
 		};
 		codec {
 			sound-dai = <&lpass_codec 0>, <&pm8916_codec 0>;
 		};
 	};

 	tertiary-dai-link {
 		link-name = "WCD-Capture";
 		cpu {
 			sound-dai = <&lpass MI2S_TERTIARY>;
 		};
 		codec {
 			sound-dai = <&lpass_codec 1>, <&pm8916_codec 1>;
 		};
 	};
 };

 &usb {
 	status = "okay";
 	extcon = <&usb_id>, <&usb_id>;
 };

 &usb_hs_phy {
 	extcon = <&usb_id>;
 };

 &venus {
 	status = "okay";
 };

 &venus_mem {
 	status = "okay";
 };

 &wcnss {
 	status = "okay";
 };

 &wcnss_iris {
 	compatible = "qcom,wcn3620";
 };

 &wcnss_mem {
 	status = "okay";
 };

 &tlmm {
 	accel_irq_default: accel-irq-default-state {
 		pins = "gpio115";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	gpio_keys_default: gpio-keys-default-state {
 		pins = "gpio107";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-pull-up;
 	};

 	gpio_leds_default: gpio-leds-default-state {
 		pins = "gpio8", "gpio9", "gpio10";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	nfc_default: nfc-default-state {
 		pins = "gpio2", "gpio20", "gpio21";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	mag_reset_default: mag-reset-default-state {
 		pins = "gpio36";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	prox_irq_default: prox-irq-default-state {
 		pins = "gpio113";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	reg_lcd_en_default: reg-lcd-en-default-state {
 		pins = "gpio32", "gpio97";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	sdc2_cd_default: sdc2-cd-default-state {
 		pins = "gpio56";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	ts_irq_default: ts-irq-default-state {
 		pins = "gpio13";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	usb_id_default: usb-id-default-state {
 		pins = "gpio117";
 		function = "gpio";

 		drive-strength = <8>;
 		bias-pull-up;
 	};
 };
	// SPDX-License-Identifier: GPL-2.0-only
	/*
	* Copyright (C) 2021 Stephan Gerhold
	*/

	/dts-v1/;

	#include "msm8916-pm8916.dtsi"
	#include <dt-bindings/gpio/gpio.h>
	#include <dt-bindings/input/input.h>
	#include <dt-bindings/interrupt-controller/irq.h>
	#include <dt-bindings/leds/common.h>
	#include <dt-bindings/sound/apq8016-lpass.h>

	/*
	* Note: The original firmware from Huawei can only boot 32-bit kernels.
	* To boot this device tree using arm64 it is necessary to flash 64-bit TZ/HYP
	* firmware (e.g. taken from the DragonBoard 410c).
	* See https://wiki.postmarketos.org/wiki/Huawei_Ascend_G7_(huawei-g7)
	* for suggested installation instructions.
	*/

	/ {
	model = "Huawei Ascend G7";
	compatible = "huawei,g7", "qcom,msm8916";
	chassis-type = "handset";

	aliases {
	mmc0 = &sdhc_1; /* eMMC */
	mmc1 = &sdhc_2; /* SD card */
	serial0 = &blsp_uart2;
	};

	chosen {
	stdout-path = "serial0";
	};

	gpio-keys {
	compatible = "gpio-keys";

	pinctrl-names = "default";
	pinctrl-0 = <&gpio_keys_default>;

	label = "GPIO Buttons";

	button-volume-up {
	label = "Volume Up";
	gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
	linux,code = <KEY_VOLUMEUP>;
	};
	};

	leds {
	compatible = "gpio-leds";

	pinctrl-names = "default";
	pinctrl-0 = <&gpio_leds_default>;

	led-0 {
	gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
	color = <LED_COLOR_ID_RED>;
	default-state = "off";
	function = LED_FUNCTION_INDICATOR;
	};

	led-1 {
	gpios = <&tlmm 9 GPIO_ACTIVE_HIGH>;
	color = <LED_COLOR_ID_GREEN>;
	default-state = "off";
	function = LED_FUNCTION_INDICATOR;
	};

	led-2 {
	gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
	color = <LED_COLOR_ID_BLUE>;
	default-state = "off";
	function = LED_FUNCTION_INDICATOR;
	};
	};

	usb_id: usb-id {
	compatible = "linux,extcon-usb-gpio";
	id-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
	pinctrl-names = "default";
	pinctrl-0 = <&usb_id_default>;
	};
	};

	&blsp_i2c2 {
	status = "okay";

	magnetometer@c {
	compatible = "asahi-kasei,ak09911";
	reg = <0x0c>;

	vdd-supply = <&pm8916_l17>;
	vid-supply = <&pm8916_l6>;

	reset-gpios = <&tlmm 36 GPIO_ACTIVE_LOW>;

	pinctrl-names = "default";
	pinctrl-0 = <&mag_reset_default>;
	};

	accelerometer@1e {
	compatible = "kionix,kx023-1025";
	reg = <0x1e>;

	interrupt-parent = <&tlmm>;
	interrupts = <115 IRQ_TYPE_EDGE_RISING>;

	vdd-supply = <&pm8916_l17>;
	vddio-supply = <&pm8916_l6>;

	pinctrl-names = "default";
	pinctrl-0 = <&accel_irq_default>;

	mount-matrix = "-1", "0", "0",
	"0", "1", "0",
	"0", "0", "1";
	};

	proximity@39 {
	compatible = "avago,apds9930";
	reg = <0x39>;

	interrupt-parent = <&tlmm>;
	interrupts = <113 IRQ_TYPE_EDGE_FALLING>;

	vdd-supply = <&pm8916_l17>;
	vddio-supply = <&pm8916_l6>;

	led-max-microamp = <100000>;
	amstaos,proximity-diodes = <1>;

	pinctrl-names = "default";
	pinctrl-0 = <&prox_irq_default>;
	};

	regulator@3e {
	compatible = "ti,tps65132";
	reg = <0x3e>;

	pinctrl-names = "default";
	pinctrl-0 = <&reg_lcd_en_default>;

	reg_lcd_pos: outp {
	regulator-name = "outp";
	regulator-min-microvolt = <5400000>;
	regulator-max-microvolt = <5400000>;
	enable-gpios = <&tlmm 97 GPIO_ACTIVE_HIGH>;
	regulator-active-discharge = <1>;
	};

	reg_lcd_neg: outn {
	regulator-name = "outn";
	regulator-min-microvolt = <5400000>;
	regulator-max-microvolt = <5400000>;
	enable-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
	regulator-active-discharge = <1>;
	};
	};
	};

	&blsp_i2c5 {
	status = "okay";

	rmi4@70 {
	compatible = "syna,rmi4-i2c";
	reg = <0x70>;
	#address-cells = <1>;
	#size-cells = <0>;

	interrupt-parent = <&tlmm>;
	interrupts = <13 IRQ_TYPE_EDGE_FALLING>;

	vdd-supply = <&pm8916_l17>;
	vio-supply = <&pm8916_l16>;

	pinctrl-names = "default";
	pinctrl-0 = <&ts_irq_default>;

	syna,startup-delay-ms = <100>;

	rmi4-f01@1 {
	reg = <0x1>;
	syna,nosleep-mode = <1>; /* Allow sleeping */
	};

	rmi4-f11@11 {
	reg = <0x11>;
	syna,sensor-type = <1>; /* Touchscreen */
	};
	};
	};

	&blsp_i2c6 {
	status = "okay";

	nfc@28 {
	compatible = "nxp,pn547", "nxp,nxp-nci-i2c";
	reg = <0x28>;

	interrupt-parent = <&tlmm>;
	interrupts = <21 IRQ_TYPE_EDGE_RISING>;

	enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
	firmware-gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;

	pinctrl-names = "default";
	pinctrl-0 = <&nfc_default>;
	};
	};

	&blsp_uart2 {
	status = "okay";
	};

	&lpass {
	status = "okay";
	};

	&lpass_codec {
	status = "okay";
	};

	&pm8916_codec {
	status = "okay";
	qcom,micbias-lvl = <2800>;
	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
	qcom,hphl-jack-type-normally-open;
	};

	&pm8916_l8 {
	regulator-min-microvolt = <2950000>;
	regulator-max-microvolt = <2950000>;
	};

	&pm8916_resin {
	status = "okay";
	linux,code = <KEY_VOLUMEDOWN>;
	};

	&pm8916_rpm_regulators {
	pm8916_l16: l16 {
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	};

	pm8916_l17: l17 {
	regulator-min-microvolt = <2850000>;
	regulator-max-microvolt = <2850000>;
	};
	};

	&pm8916_vib {
	status = "okay";
	};

	&sdhc_1 {
	status = "okay";
	};

	&sdhc_2 {
	status = "okay";

	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;

	/*
	* The Huawei device tree sets cd-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>.
	* However, gpio38 does not change its state when inserting/removing the
	* SD card, it's just low all the time. The Huawei kernel seems to use
	* polling for SD card detection instead.
	*
	* However, looking closer at the GPIO debug output it turns out that
	* gpio56 switches its state when inserting/removing the SD card.
	* It behaves just like gpio38 normally does. Usually GPIO56 is used as
	* "UIM2_PRESENT", i.e. to check if a second SIM card is inserted.
	* Maybe Huawei decided to replace the second SIM card slot with the
	* SD card slot and forgot to re-route to gpio38.
	*/
	cd-gpios = <&tlmm 56 GPIO_ACTIVE_LOW>;
	};

	&sound {
	status = "okay";

	model = "msm8916";
	audio-routing =
	"AMIC1", "MIC BIAS External1",
	"AMIC2", "MIC BIAS External2",
	"AMIC3", "MIC BIAS External1";

	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&cdc_pdm_default>;
	pinctrl-1 = <&cdc_pdm_sleep>;

	primary-dai-link {
	link-name = "WCD";
	cpu {
	sound-dai = <&lpass MI2S_PRIMARY>;
	};
	codec {
	sound-dai = <&lpass_codec 0>, <&pm8916_codec 0>;
	};
	};

	tertiary-dai-link {
	link-name = "WCD-Capture";
	cpu {
	sound-dai = <&lpass MI2S_TERTIARY>;
	};
	codec {
	sound-dai = <&lpass_codec 1>, <&pm8916_codec 1>;
	};
	};
	};

	&usb {
	status = "okay";
	extcon = <&usb_id>, <&usb_id>;
	};

	&usb_hs_phy {
	extcon = <&usb_id>;
	};

	&venus {
	status = "okay";
	};

	&venus_mem {
	status = "okay";
	};

	&wcnss {
	status = "okay";
	};

	&wcnss_iris {
	compatible = "qcom,wcn3620";
	};

	&wcnss_mem {
	status = "okay";
	};

	&tlmm {
	accel_irq_default: accel-irq-default-state {
	pins = "gpio115";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	gpio_keys_default: gpio-keys-default-state {
	pins = "gpio107";
	function = "gpio";

	drive-strength = <2>;
	bias-pull-up;
	};

	gpio_leds_default: gpio-leds-default-state {
	pins = "gpio8", "gpio9", "gpio10";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	nfc_default: nfc-default-state {
	pins = "gpio2", "gpio20", "gpio21";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	mag_reset_default: mag-reset-default-state {
	pins = "gpio36";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	prox_irq_default: prox-irq-default-state {
	pins = "gpio113";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	reg_lcd_en_default: reg-lcd-en-default-state {
	pins = "gpio32", "gpio97";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	sdc2_cd_default: sdc2-cd-default-state {
	pins = "gpio56";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	ts_irq_default: ts-irq-default-state {
	pins = "gpio13";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	usb_id_default: usb-id-default-state {
	pins = "gpio117";
	function = "gpio";

	drive-strength = <8>;
	bias-pull-up;
	};
	};