arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi - linux - Git at Google

 // SPDX-License-Identifier: GPL-2.0-only

 #include "msm8916-pm8916.dtsi"
 #include "msm8916-modem-qdsp6.dtsi"

 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/sound/apq8016-lpass.h>

 / {
 	aliases {
 		mmc0 = &sdhc_1; /* eMMC */
 		mmc1 = &sdhc_2; /* SD card */
 		serial0 = &blsp_uart2;
 	};

 	chosen {
 		stdout-path = "serial0";
 	};

 	reserved-memory {
 		/* Additional memory used by Samsung firmware modifications */
 		tz-apps@85500000 {
 			reg = <0x0 0x85500000 0x0 0xb00000>;
 			no-map;
 		};
 	};

 	battery: battery {
 		compatible = "simple-battery";
 		precharge-current-microamp = <450000>;
 		precharge-upper-limit-microvolt = <3500000>;
 	};

 	clk_pwm: pwm {
 		compatible = "clk-pwm";
 		#pwm-cells = <2>;

 		clocks = <&gcc GCC_GP2_CLK>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&motor_pwm_default>;
 		status = "disabled";
 	};

 	gpio-keys {
 		compatible = "gpio-keys";

 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_keys_default>;

 		label = "GPIO Buttons";

 		button-volume-up {
 			label = "Volume Up";
 			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 		};

 		button-home {
 			label = "Home";
 			gpios = <&tlmm 109 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOMEPAGE>;
 		};
 	};

 	gpio-hall-sensor {
 		compatible = "gpio-keys";

 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_hall_sensor_default>;

 		label = "GPIO Hall Effect Sensor";

 		event-hall-sensor {
 			label = "Hall Effect Sensor";
 			gpios = <&tlmm 52 GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_SW>;
 			linux,code = <SW_LID>;
 			linux,can-disable;
 		};
 	};

 	/*
 	 * NOTE: A5 connects GPIO 76 to a reglator powering the motor
 	 * driver IC but A3 connects the same signal to an ENABLE pin of
 	 * the driver.
 	 */
 	reg_motor_vdd: regulator-motor-vdd {
 		compatible = "regulator-fixed";
 		regulator-name = "motor_vdd";
 		regulator-min-microvolt = <3000000>;
 		regulator-max-microvolt = <3000000>;

 		gpio = <&tlmm 76 GPIO_ACTIVE_HIGH>;
 		enable-active-high;

 		pinctrl-names = "default";
 		pinctrl-0 = <&motor_en_default>;
 	};

 	reg_vdd_tsp_a: regulator-vdd-tsp-a {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_tsp_a";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;

 		gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
 		enable-active-high;

 		pinctrl-names = "default";
 		pinctrl-0 = <&tsp_en_default>;
 	};

 	i2c-muic {
 		compatible = "i2c-gpio";
 		sda-gpios = <&tlmm 105 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 		scl-gpios = <&tlmm 106 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&muic_i2c_default>;

 		#address-cells = <1>;
 		#size-cells = <0>;

 		muic: extcon@25 {
 			compatible = "siliconmitus,sm5502-muic";

 			reg = <0x25>;
 			interrupt-parent = <&tlmm>;
 			interrupts = <12 IRQ_TYPE_EDGE_FALLING>;

 			pinctrl-names = "default";
 			pinctrl-0 = <&muic_int_default>;

 			usb_con: connector {
 				compatible = "usb-b-connector";
 				label = "micro-USB";
 				type = "micro";
 			};
 		};
 	};

 	i2c-tkey {
 		compatible = "i2c-gpio";
 		sda-gpios = <&tlmm 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 		scl-gpios = <&tlmm 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&tkey_i2c_default>;

 		#address-cells = <1>;
 		#size-cells = <0>;

 		touchkey: touchkey@20 {
 			/* Note: Actually an ABOV MCU that implements same interface */
 			compatible = "coreriver,tc360-touchkey";
 			reg = <0x20>;

 			interrupt-parent = <&tlmm>;
 			interrupts = <98 IRQ_TYPE_EDGE_FALLING>;

 			/* vcc/vdd-supply are board-specific */
 			vddio-supply = <&pm8916_l6>;

 			linux,keycodes = <KEY_APPSELECT KEY_BACK>;

 			pinctrl-names = "default";
 			pinctrl-0 = <&tkey_default>;
 		};
 	};

 	i2c-nfc {
 		compatible = "i2c-gpio";
 		sda-gpios = <&tlmm 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 		scl-gpios = <&tlmm 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&nfc_i2c_default>;

 		#address-cells = <1>;
 		#size-cells = <0>;

 		nfc@27 {
 			compatible = "samsung,s3fwrn5-i2c";
 			reg = <0x27>;

 			interrupt-parent = <&tlmm>;
 			interrupts = <21 IRQ_TYPE_EDGE_RISING>;

 			en-gpios = <&tlmm 20 GPIO_ACTIVE_LOW>;
 			wake-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>;

 			clocks = <&rpmcc RPM_SMD_BB_CLK2_PIN>;

 			pinctrl-names = "default";
 			pinctrl-0 = <&nfc_default &nfc_clk_req>;
 		};
 	};

 	vibrator: vibrator {
 		compatible = "pwm-vibrator";

 		pwms = <&clk_pwm 0 100000>;
 		pwm-names = "enable";

 		vcc-supply = <&reg_motor_vdd>;
 		status = "disabled";
 	};
 };

 &blsp_i2c1 {
 	status = "okay";

 	speaker_codec: audio-codec@34 {
 		compatible = "nxp,tfa9895";
 		reg = <0x34>;
 		vddd-supply = <&pm8916_l5>;
 		sound-name-prefix = "Speaker";
 		#sound-dai-cells = <0>;
 	};
 };

 &blsp_i2c2 {
 	status = "okay";

 	accelerometer: accelerometer@10 {
 		compatible = "bosch,bmc150_accel";
 		reg = <0x10>;
 		interrupt-parent = <&tlmm>;
 		interrupts = <115 IRQ_TYPE_EDGE_RISING>;

 		vdd-supply = <&pm8916_l17>;
 		vddio-supply = <&pm8916_l5>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&accel_int_default>;
 	};

 	magnetometer@12 {
 		compatible = "bosch,bmc150_magn";
 		reg = <0x12>;

 		vdd-supply = <&pm8916_l17>;
 		vddio-supply = <&pm8916_l5>;
 	};
 };

 &blsp_i2c4 {
 	status = "okay";

 	fuel-gauge@35 {
 		compatible = "richtek,rt5033-battery";
 		reg = <0x35>;
 		interrupt-parent = <&tlmm>;
 		interrupts = <121 IRQ_TYPE_EDGE_BOTH>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&fg_alert_default>;

 		power-supplies = <&charger>;
 	};
 };

 &blsp_i2c6 {
 	status = "okay";

 	pmic@34 {
 		compatible = "richtek,rt5033";
 		reg = <0x34>;

 		interrupts-extended = <&tlmm 62 IRQ_TYPE_EDGE_FALLING>;

 		pinctrl-0 = <&pmic_int_default>;
 		pinctrl-names = "default";

 		regulators {
 			rt5033_reg_safe_ldo: SAFE_LDO {
 				regulator-min-microvolt = <4900000>;
 				regulator-max-microvolt = <4900000>;
 				regulator-always-on;
 			};

 			/*
 			 * Needed for camera, but not used yet.
 			 * Define empty nodes to allow disabling the unused
 			 * regulators.
 			 */
 			LDO {};
 			BUCK {};
 		};

 		charger: charger {
 			compatible = "richtek,rt5033-charger";
 			monitored-battery = <&battery>;
 			richtek,usb-connector = <&usb_con>;
 		};
 	};
 };

 &blsp_uart2 {
 	status = "okay";
 };

 &gpu {
 	status = "okay";
 };

 /*
  * For some reason the speaker amplifier is connected to the second SD line
  * (MI2S_2_D1) instead of the first (MI2S_2_D0). This must be configured in the
  * device tree, otherwise audio will seemingly play fine on the wrong SD line
  * but the speaker stays silent.
  *
  * When routing audio via QDSP6 (the default) the &lpass node is reserved and
  * the definitions from &q6afedai are used. When the modem is disabled audio can
  * be alternatively routed directly to the LPASS hardware with reduced latency.
  * The definitions for &lpass are here for completeness to simplify changing the
  * setup with minor changes to the DT (either manually or with DT overlays).
  */
 &lpass {
 	dai-link@3 {
 		reg = <MI2S_QUATERNARY>;
 		qcom,playback-sd-lines = <1>;
 	};
 };

 &mdss {
 	status = "okay";
 };

 &mdss_dsi0 {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&mdss_default>;
 	pinctrl-1 = <&mdss_sleep>;
 };

 &mpss_mem {
 	reg = <0x0 0x86800000 0x0 0x5400000>;
 };

 &pm8916_resin {
 	status = "okay";
 	linux,code = <KEY_VOLUMEDOWN>;
 };

 &pm8916_rpm_regulators {
 	pm8916_l17: l17 {
 		regulator-min-microvolt = <2850000>;
 		regulator-max-microvolt = <2850000>;
 	};
 };

 &q6afedai {
 	dai@22 {
 		reg = <QUATERNARY_MI2S_RX>;
 		qcom,sd-lines = <1>;
 	};
 };

 &sdhc_1 {
 	status = "okay";
 };

 &sdhc_2 {
 	status = "okay";

 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
 	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;

 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 };

 &sound {
 	model = "samsung-a2015";
 	audio-routing =
 		"AMIC1", "MIC BIAS External1",
 		"AMIC2", "MIC BIAS Internal2",
 		"AMIC3", "MIC BIAS External1";

 	pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>;
 	pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>;
 	pinctrl-names = "default", "sleep";

 	sound_link_backend2: backend2-dai-link {
 		link-name = "Quaternary MI2S";

 		cpu {
 			sound-dai = <&q6afedai QUATERNARY_MI2S_RX>;
 		};
 		platform {
 			sound-dai = <&q6routing>;
 		};
 		codec {
 			sound-dai = <&speaker_codec>;
 		};
 	};
 };

 &usb {
 	status = "okay";
 	extcon = <&muic>, <&muic>;
 };

 &usb_hs_phy {
 	extcon = <&muic>;
 };

 &venus {
 	status = "okay";
 };

 &venus_mem {
 	status = "okay";
 };

 &tlmm {
 	accel_int_default: accel-int-default-state {
 		pins = "gpio115";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	fg_alert_default: fg-alert-default-state {
 		pins = "gpio121";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	gpio_keys_default: gpio-keys-default-state {
 		pins = "gpio107", "gpio109";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-pull-up;
 	};

 	gpio_hall_sensor_default: gpio-hall-sensor-default-state {
 		pins = "gpio52";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	mdss_default: mdss-default-state {
 		pins = "gpio25";
 		function = "gpio";

 		drive-strength = <8>;
 		bias-disable;
 	};
 	mdss_sleep: mdss-sleep-state {
 		pins = "gpio25";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-pull-down;
 	};

 	motor_en_default: motor-en-default-state {
 		pins = "gpio76";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	motor_pwm_default: motor-pwm-default-state {
 		pins = "gpio50";
 		function = "gcc_gp2_clk_a";
 	};

 	muic_i2c_default: muic-i2c-default-state {
 		pins = "gpio105", "gpio106";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	muic_int_default: muic-int-default-state {
 		pins = "gpio12";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	nfc_default: nfc-default-state {
 		nfc-pins {
 			pins = "gpio20", "gpio49";
 			function = "gpio";

 			drive-strength = <2>;
 			bias-disable;
 		};

 		irq-pins {
 			pins = "gpio21";
 			function = "gpio";

 			drive-strength = <2>;
 			bias-pull-down;
 		};
 	};

 	nfc_i2c_default: nfc-i2c-default-state {
 		pins = "gpio0", "gpio1";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	pmic_int_default: pmic-int-default-state {
 		pins = "gpio62";
 		function = "gpio";
 		drive-strength = <2>;
 		bias-disable;
 	};

 	sdc2_cd_default: sdc2-cd-default-state {
 		pins = "gpio38";
 		function = "gpio";
 		drive-strength = <2>;
 		bias-disable;
 	};

 	tkey_default: tkey-default-state {
 		pins = "gpio98";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	tkey_i2c_default: tkey-i2c-default-state {
 		pins = "gpio16", "gpio17";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	tsp_en_default: tsp-en-default-state {
 		pins = "gpio73";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};

 	ts_int_default: ts-int-default-state {
 		pins = "gpio13";
 		function = "gpio";

 		drive-strength = <2>;
 		bias-disable;
 	};
 };

 &pm8916_gpios {
 	nfc_clk_req: nfc-clk-req-state {
 		pins = "gpio2";
 		function = "func1";

 		input-enable;
 		bias-disable;
 		power-source = <PM8916_GPIO_L2>;
 	};
 };
	// SPDX-License-Identifier: GPL-2.0-only

	#include "msm8916-pm8916.dtsi"
	#include "msm8916-modem-qdsp6.dtsi"

	#include <dt-bindings/gpio/gpio.h>
	#include <dt-bindings/input/input.h>
	#include <dt-bindings/interrupt-controller/irq.h>
	#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
	#include <dt-bindings/sound/apq8016-lpass.h>

	/ {
	aliases {
	mmc0 = &sdhc_1; /* eMMC */
	mmc1 = &sdhc_2; /* SD card */
	serial0 = &blsp_uart2;
	};

	chosen {
	stdout-path = "serial0";
	};

	reserved-memory {
	/* Additional memory used by Samsung firmware modifications */
	tz-apps@85500000 {
	reg = <0x0 0x85500000 0x0 0xb00000>;
	no-map;
	};
	};

	battery: battery {
	compatible = "simple-battery";
	precharge-current-microamp = <450000>;
	precharge-upper-limit-microvolt = <3500000>;
	};

	clk_pwm: pwm {
	compatible = "clk-pwm";
	#pwm-cells = <2>;

	clocks = <&gcc GCC_GP2_CLK>;

	pinctrl-names = "default";
	pinctrl-0 = <&motor_pwm_default>;
	status = "disabled";
	};

	gpio-keys {
	compatible = "gpio-keys";

	pinctrl-names = "default";
	pinctrl-0 = <&gpio_keys_default>;

	label = "GPIO Buttons";

	button-volume-up {
	label = "Volume Up";
	gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
	linux,code = <KEY_VOLUMEUP>;
	};

	button-home {
	label = "Home";
	gpios = <&tlmm 109 GPIO_ACTIVE_LOW>;
	linux,code = <KEY_HOMEPAGE>;
	};
	};

	gpio-hall-sensor {
	compatible = "gpio-keys";

	pinctrl-names = "default";
	pinctrl-0 = <&gpio_hall_sensor_default>;

	label = "GPIO Hall Effect Sensor";

	event-hall-sensor {
	label = "Hall Effect Sensor";
	gpios = <&tlmm 52 GPIO_ACTIVE_LOW>;
	linux,input-type = <EV_SW>;
	linux,code = <SW_LID>;
	linux,can-disable;
	};
	};

	/*
	* NOTE: A5 connects GPIO 76 to a reglator powering the motor
	* driver IC but A3 connects the same signal to an ENABLE pin of
	* the driver.
	*/
	reg_motor_vdd: regulator-motor-vdd {
	compatible = "regulator-fixed";
	regulator-name = "motor_vdd";
	regulator-min-microvolt = <3000000>;
	regulator-max-microvolt = <3000000>;

	gpio = <&tlmm 76 GPIO_ACTIVE_HIGH>;
	enable-active-high;

	pinctrl-names = "default";
	pinctrl-0 = <&motor_en_default>;
	};

	reg_vdd_tsp_a: regulator-vdd-tsp-a {
	compatible = "regulator-fixed";
	regulator-name = "vdd_tsp_a";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;

	gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
	enable-active-high;

	pinctrl-names = "default";
	pinctrl-0 = <&tsp_en_default>;
	};

	i2c-muic {
	compatible = "i2c-gpio";
	sda-gpios = <&tlmm 105 (GPIO_ACTIVE_HIGH\|GPIO_OPEN_DRAIN)>;
	scl-gpios = <&tlmm 106 (GPIO_ACTIVE_HIGH\|GPIO_OPEN_DRAIN)>;

	pinctrl-names = "default";
	pinctrl-0 = <&muic_i2c_default>;

	#address-cells = <1>;
	#size-cells = <0>;

	muic: extcon@25 {
	compatible = "siliconmitus,sm5502-muic";

	reg = <0x25>;
	interrupt-parent = <&tlmm>;
	interrupts = <12 IRQ_TYPE_EDGE_FALLING>;

	pinctrl-names = "default";
	pinctrl-0 = <&muic_int_default>;

	usb_con: connector {
	compatible = "usb-b-connector";
	label = "micro-USB";
	type = "micro";
	};
	};
	};

	i2c-tkey {
	compatible = "i2c-gpio";
	sda-gpios = <&tlmm 16 (GPIO_ACTIVE_HIGH\|GPIO_OPEN_DRAIN)>;
	scl-gpios = <&tlmm 17 (GPIO_ACTIVE_HIGH\|GPIO_OPEN_DRAIN)>;

	pinctrl-names = "default";
	pinctrl-0 = <&tkey_i2c_default>;

	#address-cells = <1>;
	#size-cells = <0>;

	touchkey: touchkey@20 {
	/* Note: Actually an ABOV MCU that implements same interface */
	compatible = "coreriver,tc360-touchkey";
	reg = <0x20>;

	interrupt-parent = <&tlmm>;
	interrupts = <98 IRQ_TYPE_EDGE_FALLING>;

	/* vcc/vdd-supply are board-specific */
	vddio-supply = <&pm8916_l6>;

	linux,keycodes = <KEY_APPSELECT KEY_BACK>;

	pinctrl-names = "default";
	pinctrl-0 = <&tkey_default>;
	};
	};

	i2c-nfc {
	compatible = "i2c-gpio";
	sda-gpios = <&tlmm 0 (GPIO_ACTIVE_HIGH\|GPIO_OPEN_DRAIN)>;
	scl-gpios = <&tlmm 1 (GPIO_ACTIVE_HIGH\|GPIO_OPEN_DRAIN)>;

	pinctrl-names = "default";
	pinctrl-0 = <&nfc_i2c_default>;

	#address-cells = <1>;
	#size-cells = <0>;

	nfc@27 {
	compatible = "samsung,s3fwrn5-i2c";
	reg = <0x27>;

	interrupt-parent = <&tlmm>;
	interrupts = <21 IRQ_TYPE_EDGE_RISING>;

	en-gpios = <&tlmm 20 GPIO_ACTIVE_LOW>;
	wake-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>;

	clocks = <&rpmcc RPM_SMD_BB_CLK2_PIN>;

	pinctrl-names = "default";
	pinctrl-0 = <&nfc_default &nfc_clk_req>;
	};
	};

	vibrator: vibrator {
	compatible = "pwm-vibrator";

	pwms = <&clk_pwm 0 100000>;
	pwm-names = "enable";

	vcc-supply = <&reg_motor_vdd>;
	status = "disabled";
	};
	};

	&blsp_i2c1 {
	status = "okay";

	speaker_codec: audio-codec@34 {
	compatible = "nxp,tfa9895";
	reg = <0x34>;
	vddd-supply = <&pm8916_l5>;
	sound-name-prefix = "Speaker";
	#sound-dai-cells = <0>;
	};
	};

	&blsp_i2c2 {
	status = "okay";

	accelerometer: accelerometer@10 {
	compatible = "bosch,bmc150_accel";
	reg = <0x10>;
	interrupt-parent = <&tlmm>;
	interrupts = <115 IRQ_TYPE_EDGE_RISING>;

	vdd-supply = <&pm8916_l17>;
	vddio-supply = <&pm8916_l5>;

	pinctrl-names = "default";
	pinctrl-0 = <&accel_int_default>;
	};

	magnetometer@12 {
	compatible = "bosch,bmc150_magn";
	reg = <0x12>;

	vdd-supply = <&pm8916_l17>;
	vddio-supply = <&pm8916_l5>;
	};
	};

	&blsp_i2c4 {
	status = "okay";

	fuel-gauge@35 {
	compatible = "richtek,rt5033-battery";
	reg = <0x35>;
	interrupt-parent = <&tlmm>;
	interrupts = <121 IRQ_TYPE_EDGE_BOTH>;

	pinctrl-names = "default";
	pinctrl-0 = <&fg_alert_default>;

	power-supplies = <&charger>;
	};
	};

	&blsp_i2c6 {
	status = "okay";

	pmic@34 {
	compatible = "richtek,rt5033";
	reg = <0x34>;

	interrupts-extended = <&tlmm 62 IRQ_TYPE_EDGE_FALLING>;

	pinctrl-0 = <&pmic_int_default>;
	pinctrl-names = "default";

	regulators {
	rt5033_reg_safe_ldo: SAFE_LDO {
	regulator-min-microvolt = <4900000>;
	regulator-max-microvolt = <4900000>;
	regulator-always-on;
	};

	/*
	* Needed for camera, but not used yet.
	* Define empty nodes to allow disabling the unused
	* regulators.
	*/
	LDO {};
	BUCK {};
	};

	charger: charger {
	compatible = "richtek,rt5033-charger";
	monitored-battery = <&battery>;
	richtek,usb-connector = <&usb_con>;
	};
	};
	};

	&blsp_uart2 {
	status = "okay";
	};

	&gpu {
	status = "okay";
	};

	/*
	* For some reason the speaker amplifier is connected to the second SD line
	* (MI2S_2_D1) instead of the first (MI2S_2_D0). This must be configured in the
	* device tree, otherwise audio will seemingly play fine on the wrong SD line
	* but the speaker stays silent.
	*
	* When routing audio via QDSP6 (the default) the &lpass node is reserved and
	* the definitions from &q6afedai are used. When the modem is disabled audio can
	* be alternatively routed directly to the LPASS hardware with reduced latency.
	* The definitions for &lpass are here for completeness to simplify changing the
	* setup with minor changes to the DT (either manually or with DT overlays).
	*/
	&lpass {
	dai-link@3 {
	reg = <MI2S_QUATERNARY>;
	qcom,playback-sd-lines = <1>;
	};
	};

	&mdss {
	status = "okay";
	};

	&mdss_dsi0 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&mdss_default>;
	pinctrl-1 = <&mdss_sleep>;
	};

	&mpss_mem {
	reg = <0x0 0x86800000 0x0 0x5400000>;
	};

	&pm8916_resin {
	status = "okay";
	linux,code = <KEY_VOLUMEDOWN>;
	};

	&pm8916_rpm_regulators {
	pm8916_l17: l17 {
	regulator-min-microvolt = <2850000>;
	regulator-max-microvolt = <2850000>;
	};
	};

	&q6afedai {
	dai@22 {
	reg = <QUATERNARY_MI2S_RX>;
	qcom,sd-lines = <1>;
	};
	};

	&sdhc_1 {
	status = "okay";
	};

	&sdhc_2 {
	status = "okay";

	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;

	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
	};

	&sound {
	model = "samsung-a2015";
	audio-routing =
	"AMIC1", "MIC BIAS External1",
	"AMIC2", "MIC BIAS Internal2",
	"AMIC3", "MIC BIAS External1";

	pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>;
	pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>;
	pinctrl-names = "default", "sleep";

	sound_link_backend2: backend2-dai-link {
	link-name = "Quaternary MI2S";

	cpu {
	sound-dai = <&q6afedai QUATERNARY_MI2S_RX>;
	};
	platform {
	sound-dai = <&q6routing>;
	};
	codec {
	sound-dai = <&speaker_codec>;
	};
	};
	};

	&usb {
	status = "okay";
	extcon = <&muic>, <&muic>;
	};

	&usb_hs_phy {
	extcon = <&muic>;
	};

	&venus {
	status = "okay";
	};

	&venus_mem {
	status = "okay";
	};

	&tlmm {
	accel_int_default: accel-int-default-state {
	pins = "gpio115";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	fg_alert_default: fg-alert-default-state {
	pins = "gpio121";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	gpio_keys_default: gpio-keys-default-state {
	pins = "gpio107", "gpio109";
	function = "gpio";

	drive-strength = <2>;
	bias-pull-up;
	};

	gpio_hall_sensor_default: gpio-hall-sensor-default-state {
	pins = "gpio52";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	mdss_default: mdss-default-state {
	pins = "gpio25";
	function = "gpio";

	drive-strength = <8>;
	bias-disable;
	};
	mdss_sleep: mdss-sleep-state {
	pins = "gpio25";
	function = "gpio";

	drive-strength = <2>;
	bias-pull-down;
	};

	motor_en_default: motor-en-default-state {
	pins = "gpio76";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	motor_pwm_default: motor-pwm-default-state {
	pins = "gpio50";
	function = "gcc_gp2_clk_a";
	};

	muic_i2c_default: muic-i2c-default-state {
	pins = "gpio105", "gpio106";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	muic_int_default: muic-int-default-state {
	pins = "gpio12";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	nfc_default: nfc-default-state {
	nfc-pins {
	pins = "gpio20", "gpio49";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	irq-pins {
	pins = "gpio21";
	function = "gpio";

	drive-strength = <2>;
	bias-pull-down;
	};
	};

	nfc_i2c_default: nfc-i2c-default-state {
	pins = "gpio0", "gpio1";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	pmic_int_default: pmic-int-default-state {
	pins = "gpio62";
	function = "gpio";
	drive-strength = <2>;
	bias-disable;
	};

	sdc2_cd_default: sdc2-cd-default-state {
	pins = "gpio38";
	function = "gpio";
	drive-strength = <2>;
	bias-disable;
	};

	tkey_default: tkey-default-state {
	pins = "gpio98";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	tkey_i2c_default: tkey-i2c-default-state {
	pins = "gpio16", "gpio17";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	tsp_en_default: tsp-en-default-state {
	pins = "gpio73";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};

	ts_int_default: ts-int-default-state {
	pins = "gpio13";
	function = "gpio";

	drive-strength = <2>;
	bias-disable;
	};
	};

	&pm8916_gpios {
	nfc_clk_req: nfc-clk-req-state {
	pins = "gpio2";
	function = "func1";

	input-enable;
	bias-disable;
	power-source = <PM8916_GPIO_L2>;
	};
	};