| // SPDX-License-Identifier: GPL-2.0-only |
| |
| /dts-v1/; |
| |
| #include "msm8939-pm8916.dtsi" |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-mpp.h> |
| |
| / { |
| model = "BQ Aquaris M5 (Longcheer L9100)"; |
| compatible = "longcheer,l9100", "qcom,msm8939"; |
| chassis-type = "handset"; |
| |
| aliases { |
| mmc0 = &sdhc_1; /* eMMC */ |
| mmc1 = &sdhc_2; /* SD card */ |
| serial0 = &blsp_uart2; |
| }; |
| |
| chosen { |
| stdout-path = "serial0"; |
| }; |
| |
| gpio-hall-sensor { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&gpio_hall_sensor_default>; |
| pinctrl-names = "default"; |
| |
| label = "GPIO Hall Effect Sensor"; |
| |
| event-hall-sensor { |
| label = "Hall Effect Sensor"; |
| gpios = <&tlmm 20 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_LID>; |
| linux,can-disable; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&gpio_keys_default>; |
| pinctrl-names = "default"; |
| |
| label = "GPIO Buttons"; |
| |
| button-volume-up { |
| label = "Volume Up"; |
| gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| led-0 { |
| gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>; |
| color = <LED_COLOR_ID_WHITE>; |
| default-state = "off"; |
| function = LED_FUNCTION_KBD_BACKLIGHT; |
| |
| pinctrl-0 = <&button_backlight_default>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| reg_ts_vdd: regulator-vdd-ts { |
| compatible = "regulator-fixed"; |
| regulator-name = "regulator-vdd-ts"; |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| |
| gpio = <&tlmm 78 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&ts_vdd_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| backlight { |
| compatible = "pwm-backlight"; |
| pwms = <&pm8916_pwm 0 100000>; |
| brightness-levels = <0 255>; |
| num-interpolated-steps = <255>; |
| default-brightness-level = <128>; |
| enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-0 = <&lcd_bl_en_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| flash-led-controller { |
| compatible = "ocs,ocp8110"; |
| flash-gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>; |
| enable-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-0 = <&camera_front_flash_default>; |
| pinctrl-names = "default"; |
| |
| led { |
| function = LED_FUNCTION_FLASH; |
| color = <LED_COLOR_ID_WHITE>; |
| flash-max-timeout-us = <250000>; |
| }; |
| }; |
| |
| usb_id: usb-id { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; |
| pinctrl-0 = <&usb_id_default &usb_id_switch_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| }; |
| |
| &blsp_i2c2 { |
| status = "okay"; |
| |
| led-controller@30 { |
| compatible = "kinetic,ktd2026"; |
| reg = <0x30>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vin-supply = <&pm8916_l17>; |
| vio-supply = <&pm8916_l6>; |
| |
| pinctrl-0 = <&status_led_default>; |
| pinctrl-names = "default"; |
| |
| multi-led { |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_STATUS; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@0 { |
| reg = <0>; |
| color = <LED_COLOR_ID_RED>; |
| }; |
| |
| led@1 { |
| reg = <1>; |
| color = <LED_COLOR_ID_GREEN>; |
| }; |
| |
| led@2 { |
| reg = <2>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| }; |
| }; |
| |
| flash-led-controller@53 { |
| compatible = "silergy,sy7802"; |
| reg = <0x53>; |
| |
| enable-gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-0 = <&camera_rear_flash_default>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@0 { |
| reg = <0>; |
| function = LED_FUNCTION_FLASH; |
| color = <LED_COLOR_ID_WHITE>; |
| led-sources = <0>, <1>; |
| }; |
| }; |
| }; |
| |
| &blsp_i2c3 { |
| status = "okay"; |
| |
| magnetometer@d { |
| compatible = "asahi-kasei,ak09911"; |
| reg = <0x0d>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vid-supply = <&pm8916_l6>; |
| |
| reset-gpios = <&tlmm 68 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-0 = <&mag_reset_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| light-sensor@23 { |
| compatible = "liteon,ltr559"; |
| reg = <0x23>; |
| proximity-near-level = <75>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vddio-supply = <&pm8916_l5>; |
| |
| interrupts-extended = <&tlmm 113 IRQ_TYPE_EDGE_FALLING>; |
| |
| pinctrl-0 = <&light_int_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| imu@68 { |
| compatible = "bosch,bmi160"; |
| reg = <0x68>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vddio-supply = <&pm8916_l6>; |
| }; |
| }; |
| |
| &blsp_i2c5 { |
| status = "okay"; |
| |
| touchscreen@4a { |
| compatible = "atmel,maxtouch"; |
| reg = <0x4a>; |
| |
| interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>; |
| |
| reset-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>; |
| |
| vdda-supply = <&pm8916_l6>; |
| vdd-supply = <®_ts_vdd>; |
| |
| pinctrl-0 = <&ts_int_reset_default>; |
| pinctrl-names = "default"; |
| |
| /* Keys listed from right to left */ |
| linux,keycodes = <KEY_APPSELECT KEY_HOMEPAGE KEY_BACK>; |
| }; |
| }; |
| |
| &blsp_uart2 { |
| status = "okay"; |
| }; |
| |
| &pm8916_gpios { |
| status_led_default: status-led-default-state { |
| pins = "gpio3"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| power-source = <PM8916_GPIO_VPH>; |
| bias-disable; |
| output-high; |
| }; |
| }; |
| |
| &pm8916_mpps { |
| pwm_out: mpp4-state { |
| pins = "mpp4"; |
| function = "digital"; |
| power-source = <PM8916_MPP_VPH>; |
| output-low; |
| qcom,dtest = <1>; |
| }; |
| }; |
| |
| &pm8916_pwm { |
| pinctrl-0 = <&pwm_out>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| |
| &pm8916_resin { |
| linux,code = <KEY_VOLUMEDOWN>; |
| status = "okay"; |
| }; |
| |
| &pm8916_rpm_regulators { |
| pm8916_l17: l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| }; |
| |
| &pm8916_vib { |
| status = "okay"; |
| }; |
| |
| &sdhc_1 { |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| pinctrl-0 = <&sdc2_default &sdc2_cd_default>; |
| pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>; |
| pinctrl-names = "default", "sleep"; |
| |
| cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; |
| |
| status = "okay"; |
| }; |
| |
| &usb { |
| extcon = <&usb_id>, <&usb_id>; |
| status = "okay"; |
| }; |
| |
| &usb_hs_phy { |
| extcon = <&usb_id>; |
| }; |
| |
| &wcnss { |
| status = "okay"; |
| }; |
| |
| &wcnss_iris { |
| compatible = "qcom,wcn3620"; |
| }; |
| |
| &wcnss_mem { |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| button_backlight_default: button-backlight-default-state { |
| pins = "gpio17"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| camera_front_flash_default: camera-front-flash-default-state { |
| pins = "gpio8", "gpio49"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| camera_rear_flash_default: camera-rear-flash-default-state { |
| pins = "gpio9", "gpio16", "gpio51"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| gpio_hall_sensor_default: gpio-hall-sensor-default-state { |
| pins = "gpio20"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| gpio_keys_default: gpio-keys-default-state { |
| pins = "gpio107"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| lcd_bl_en_default: lcd-bl-en-default-state { |
| pins = "gpio98"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| light_int_default: light-int-default-state { |
| pins = "gpio113"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| mag_reset_default: mag-reset-default-state { |
| pins = "gpio68"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| sdc2_cd_default: sdc2-cd-default-state { |
| pins = "gpio38"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| ts_int_reset_default: ts-int-reset-default-state { |
| pins = "gpio12", "gpio13"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| ts_vdd_default: ts-vdd-default-state { |
| pins = "gpio78"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| usb_id_default: usb-id-default-state { |
| pins = "gpio110"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| |
| usb_id_switch_default: usb-id-switch-default-state { |
| pins = "gpio121"; |
| function = "gpio"; |
| drive-strength = <2>; |
| output-high; |
| }; |
| }; |
