| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved. |
| */ |
| |
| /dts-v1/; |
| |
| /* PM7250B is configured to use SID8/9 */ |
| #define PM7250B_SID 8 |
| #define PM7250B_SID1 9 |
| |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include "sc7280.dtsi" |
| #include "pm7250b.dtsi" |
| #include "pm7325.dtsi" |
| #include "pm8350c.dtsi" |
| #include "pmk8350.dtsi" |
| |
| /delete-node/ &ipa_fw_mem; |
| /delete-node/ &rmtfs_mem; |
| /delete-node/ &adsp_mem; |
| /delete-node/ &cdsp_mem; |
| /delete-node/ &video_mem; |
| /delete-node/ &wlan_ce_mem; |
| /delete-node/ &wpss_mem; |
| /delete-node/ &xbl_mem; |
| |
| / { |
| model = "Qualcomm Technologies, Inc. QCM6490 IDP"; |
| compatible = "qcom,qcm6490-idp", "qcom,qcm6490"; |
| chassis-type = "embedded"; |
| |
| aliases { |
| serial0 = &uart5; |
| }; |
| |
| pm8350c_pwm_backlight: backlight { |
| compatible = "pwm-backlight"; |
| pwms = <&pm8350c_pwm 3 65535>; |
| enable-gpios = <&pm8350c_gpios 7 GPIO_ACTIVE_HIGH>; |
| pinctrl-0 = <&pmic_lcd_bl_en>; |
| pinctrl-names = "default"; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| lcd_disp_bias: regulator-lcd-disp-bias { |
| compatible = "regulator-fixed"; |
| regulator-name = "lcd_disp_bias"; |
| regulator-min-microvolt = <5500000>; |
| regulator-max-microvolt = <5500000>; |
| gpio = <&pm7250b_gpios 2 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| pinctrl-0 = <&lcd_disp_bias_en>; |
| pinctrl-names = "default"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&key_vol_up_default>; |
| pinctrl-names = "default"; |
| |
| key-volume-up { |
| label = "Volume_up"; |
| gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| wakeup-source; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| }; |
| |
| reserved-memory { |
| xbl_mem: xbl@80700000 { |
| reg = <0x0 0x80700000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| cdsp_secure_heap_mem: cdsp-secure-heap@81800000 { |
| reg = <0x0 0x81800000 0x0 0x1e00000>; |
| no-map; |
| }; |
| |
| camera_mem: camera@84300000 { |
| reg = <0x0 0x84300000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| wpss_mem: wpss@84800000 { |
| reg = <0x0 0x84800000 0x0 0x1900000>; |
| no-map; |
| }; |
| |
| adsp_mem: adsp@86100000 { |
| reg = <0x0 0x86100000 0x0 0x2800000>; |
| no-map; |
| }; |
| |
| cdsp_mem: cdsp@88900000 { |
| reg = <0x0 0x88900000 0x0 0x1e00000>; |
| no-map; |
| }; |
| |
| video_mem: video@8a700000 { |
| reg = <0x0 0x8a700000 0x0 0x700000>; |
| no-map; |
| }; |
| |
| cvp_mem: cvp@8ae00000 { |
| reg = <0x0 0x8ae00000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| ipa_fw_mem: ipa-fw@8b300000 { |
| reg = <0x0 0x8b300000 0x0 0x10000>; |
| no-map; |
| }; |
| |
| ipa_gsi_mem: ipa-gsi@8b310000 { |
| reg = <0x0 0x8b310000 0x0 0xa000>; |
| no-map; |
| }; |
| |
| gpu_microcode_mem: gpu-microcode@8b31a000 { |
| reg = <0x0 0x8b31a000 0x0 0x2000>; |
| no-map; |
| }; |
| |
| mpss_mem: mpss@8b800000 { |
| reg = <0x0 0x8b800000 0x0 0xf600000>; |
| no-map; |
| }; |
| |
| tz_stat_mem: tz-stat@c0000000 { |
| reg = <0x0 0xc0000000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| tags_mem: tags@c0100000 { |
| reg = <0x0 0xc0100000 0x0 0x1200000>; |
| no-map; |
| }; |
| |
| qtee_mem: qtee@c1300000 { |
| reg = <0x0 0xc1300000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| trusted_apps_mem: trusted-apps@c1800000 { |
| reg = <0x0 0xc1800000 0x0 0x1c00000>; |
| no-map; |
| }; |
| |
| debug_vm_mem: debug-vm@d0600000 { |
| reg = <0x0 0xd0600000 0x0 0x100000>; |
| no-map; |
| }; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| }; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm7325-rpmh-regulators"; |
| qcom,pmic-id = "b"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| vdd-s7-supply = <&vph_pwr>; |
| vdd-s8-supply = <&vph_pwr>; |
| vdd-l1-l4-l12-l15-supply = <&vreg_s7b_0p972>; |
| vdd-l2-l7-supply = <&vreg_bob_3p296>; |
| vdd-l3-supply = <&vreg_s2b_0p876>; |
| vdd-l5-supply = <&vreg_s2b_0p876>; |
| vdd-l6-l9-l10-supply = <&vreg_s8b_1p272>; |
| vdd-l8-supply = <&vreg_s7b_0p972>; |
| vdd-l11-l17-l18-l19-supply = <&vreg_s1b_1p872>; |
| vdd-l13-supply = <&vreg_s7b_0p972>; |
| vdd-l14-l16-supply = <&vreg_s8b_1p272>; |
| |
| vreg_s1b_1p872: smps1 { |
| regulator-name = "vreg_s1b_1p872"; |
| regulator-min-microvolt = <1840000>; |
| regulator-max-microvolt = <2040000>; |
| }; |
| |
| vreg_s2b_0p876: smps2 { |
| regulator-name = "vreg_s2b_0p876"; |
| regulator-min-microvolt = <570070>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| vreg_s7b_0p972: smps7 { |
| regulator-name = "vreg_s7b_0p972"; |
| regulator-min-microvolt = <535000>; |
| regulator-max-microvolt = <1120000>; |
| }; |
| |
| vreg_s8b_1p272: smps8 { |
| regulator-name = "vreg_s8b_1p272"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1500000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_RET>; |
| }; |
| |
| vreg_l1b_0p912: ldo1 { |
| regulator-name = "vreg_l1b_0p912"; |
| regulator-min-microvolt = <825000>; |
| regulator-max-microvolt = <925000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2b_3p072: ldo2 { |
| regulator-name = "vreg_l2b_3p072"; |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <3544000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3b_0p504: ldo3 { |
| regulator-name = "vreg_l3b_0p504"; |
| regulator-min-microvolt = <312000>; |
| regulator-max-microvolt = <910000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4b_0p752: ldo4 { |
| regulator-name = "vreg_l4b_0p752"; |
| regulator-min-microvolt = <752000>; |
| regulator-max-microvolt = <820000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| reg_l5b_0p752: ldo5 { |
| regulator-name = "reg_l5b_0p752"; |
| regulator-min-microvolt = <552000>; |
| regulator-max-microvolt = <832000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6b_1p2: ldo6 { |
| regulator-name = "vreg_l6b_1p2"; |
| regulator-min-microvolt = <1140000>; |
| regulator-max-microvolt = <1260000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7b_2p952: ldo7 { |
| regulator-name = "vreg_l7b_2p952"; |
| regulator-min-microvolt = <2400000>; |
| regulator-max-microvolt = <3544000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8b_0p904: ldo8 { |
| regulator-name = "vreg_l8b_0p904"; |
| regulator-min-microvolt = <870000>; |
| regulator-max-microvolt = <970000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9b_1p2: ldo9 { |
| regulator-name = "vreg_l9b_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l11b_1p504: ldo11 { |
| regulator-name = "vreg_l11b_1p504"; |
| regulator-min-microvolt = <1504000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12b_0p751: ldo12 { |
| regulator-name = "vreg_l12b_0p751"; |
| regulator-min-microvolt = <751000>; |
| regulator-max-microvolt = <824000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13b_0p53: ldo13 { |
| regulator-name = "vreg_l13b_0p53"; |
| regulator-min-microvolt = <530000>; |
| regulator-max-microvolt = <824000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14b_1p08: ldo14 { |
| regulator-name = "vreg_l14b_1p08"; |
| regulator-min-microvolt = <1080000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l15b_0p765: ldo15 { |
| regulator-name = "vreg_l15b_0p765"; |
| regulator-min-microvolt = <765000>; |
| regulator-max-microvolt = <1020000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l16b_1p1: ldo16 { |
| regulator-name = "vreg_l16b_1p1"; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l17b_1p7: ldo17 { |
| regulator-name = "vreg_l17b_1p7"; |
| regulator-min-microvolt = <1700000>; |
| regulator-max-microvolt = <1900000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l18b_1p8: ldo18 { |
| regulator-name = "vreg_l18b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l19b_1p8: ldo19 { |
| regulator-name = "vreg_l19b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm8350c-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| vdd-s7-supply = <&vph_pwr>; |
| vdd-s8-supply = <&vph_pwr>; |
| vdd-s9-supply = <&vph_pwr>; |
| vdd-s10-supply = <&vph_pwr>; |
| vdd-l1-l12-supply = <&vreg_s1b_1p872>; |
| vdd-l2-l8-supply = <&vreg_s1b_1p872>; |
| vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob_3p296>; |
| vdd-l6-l9-l11-supply = <&vreg_bob_3p296>; |
| vdd-l10-supply = <&vreg_s7b_0p972>; |
| vdd-bob-supply = <&vph_pwr>; |
| |
| vreg_s1c_2p19: smps1 { |
| regulator-name = "vreg_s1c_2p19"; |
| regulator-min-microvolt = <2190000>; |
| regulator-max-microvolt = <2210000>; |
| }; |
| |
| vreg_s2c_0p752: smps2 { |
| regulator-name = "vreg_s2c_0p752"; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <800000>; |
| }; |
| |
| vreg_s5c_0p752: smps5 { |
| regulator-name = "vreg_s5c_0p752"; |
| regulator-min-microvolt = <465000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| vreg_s7c_0p752: smps7 { |
| regulator-name = "vreg_s7c_0p752"; |
| regulator-min-microvolt = <465000>; |
| regulator-max-microvolt = <800000>; |
| }; |
| |
| vreg_s9c_1p084: smps9 { |
| regulator-name = "vreg_s9c_1p084"; |
| regulator-min-microvolt = <1010000>; |
| regulator-max-microvolt = <1170000>; |
| }; |
| |
| vreg_l1c_1p8: ldo1 { |
| regulator-name = "vreg_l1c_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1980000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2c_1p62: ldo2 { |
| regulator-name = "vreg_l2c_1p62"; |
| regulator-min-microvolt = <1620000>; |
| regulator-max-microvolt = <1980000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3c_2p8: ldo3 { |
| regulator-name = "vreg_l3c_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <3540000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4c_1p62: ldo4 { |
| regulator-name = "vreg_l4c_1p62"; |
| regulator-min-microvolt = <1620000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5c_1p62: ldo5 { |
| regulator-name = "vreg_l5c_1p62"; |
| regulator-min-microvolt = <1620000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6c_2p96: ldo6 { |
| regulator-name = "vreg_l6c_2p96"; |
| regulator-min-microvolt = <1650000>; |
| regulator-max-microvolt = <3544000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7c_3p0: ldo7 { |
| regulator-name = "vreg_l7c_3p0"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3544000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8c_1p62: ldo8 { |
| regulator-name = "vreg_l8c_1p62"; |
| regulator-min-microvolt = <1620000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9c_2p96: ldo9 { |
| regulator-name = "vreg_l9c_2p96"; |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <35440000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10c_0p88: ldo10 { |
| regulator-name = "vreg_l10c_0p88"; |
| regulator-min-microvolt = <720000>; |
| regulator-max-microvolt = <1050000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l11c_2p8: ldo11 { |
| regulator-name = "vreg_l11c_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <3544000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12c_1p65: ldo12 { |
| regulator-name = "vreg_l12c_1p65"; |
| regulator-min-microvolt = <1650000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13c_2p7: ldo13 { |
| regulator-name = "vreg_l13c_2p7"; |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <3544000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_bob_3p296: bob { |
| regulator-name = "vreg_bob_3p296"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3960000>; |
| }; |
| }; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dsi { |
| vdda-supply = <&vreg_l6b_1p2>; |
| status = "okay"; |
| |
| panel@0 { |
| compatible = "novatek,nt36672e"; |
| reg = <0>; |
| |
| reset-gpios = <&tlmm 44 GPIO_ACTIVE_HIGH>; |
| |
| vddi-supply = <&vreg_l8c_1p62>; |
| avdd-supply = <&lcd_disp_bias>; |
| avee-supply = <&lcd_disp_bias>; |
| |
| backlight = <&pm8350c_pwm_backlight>; |
| |
| port { |
| panel0_in: endpoint { |
| remote-endpoint = <&mdss_dsi0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dsi0_out { |
| remote-endpoint = <&panel0_in>; |
| data-lanes = <0 1 2 3>; |
| }; |
| |
| &mdss_dsi_phy { |
| vdds-supply = <&vreg_l10c_0p88>; |
| status = "okay"; |
| }; |
| |
| &pm7250b_gpios { |
| lcd_disp_bias_en: lcd-disp-bias-en-state { |
| pins = "gpio2"; |
| function = "func1"; |
| bias-disable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; |
| input-disable; |
| output-enable; |
| power-source = <0>; |
| }; |
| }; |
| |
| &pm8350c_gpios { |
| pmic_lcd_bl_en: pmic-lcd-bl-en-state { |
| pins = "gpio7"; |
| function = "normal"; |
| bias-disable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; |
| output-low; |
| power-source = <0>; |
| }; |
| |
| pmic_lcd_bl_pwm: pmic-lcd-bl-pwm-state { |
| pins = "gpio8"; |
| function = "func1"; |
| bias-disable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; |
| output-low; |
| power-source = <0>; |
| }; |
| }; |
| |
| &pm7325_gpios { |
| key_vol_up_default: key-vol-up-state { |
| pins = "gpio6"; |
| function = "normal"; |
| input-enable; |
| bias-pull-up; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; |
| }; |
| }; |
| |
| &pm8350c_pwm { |
| pinctrl-0 = <&pmic_lcd_bl_pwm>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| multi-led { |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_STATUS; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@1 { |
| reg = <1>; |
| color = <LED_COLOR_ID_RED>; |
| }; |
| |
| led@2 { |
| reg = <2>; |
| color = <LED_COLOR_ID_GREEN>; |
| }; |
| |
| led@3 { |
| reg = <3>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| }; |
| }; |
| |
| &pon_pwrkey { |
| status = "okay"; |
| }; |
| |
| &pon_resin { |
| linux,code = <KEY_VOLUMEDOWN>; |
| status = "okay"; |
| }; |
| |
| &qupv3_id_0 { |
| status = "okay"; |
| }; |
| |
| &remoteproc_adsp { |
| firmware-name = "qcom/qcm6490/adsp.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_cdsp { |
| firmware-name = "qcom/qcm6490/cdsp.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_mpss { |
| firmware-name = "qcom/qcm6490/modem.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_wpss { |
| firmware-name = "qcom/qcm6490/wpss.mbn"; |
| status = "okay"; |
| }; |
| |
| &sdc2_clk { |
| bias-disable; |
| drive-strength = <16>; |
| }; |
| |
| &sdc2_cmd { |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| &sdc2_data { |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| &sdhc_1 { |
| non-removable; |
| no-sd; |
| no-sdio; |
| |
| vmmc-supply = <&vreg_l7b_2p952>; |
| vqmmc-supply = <&vreg_l19b_1p8>; |
| |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| status = "okay"; |
| |
| pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>, <&sd_cd>; |
| pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>, <&sd_cd>; |
| |
| vmmc-supply = <&vreg_l9c_2p96>; |
| vqmmc-supply = <&vreg_l6c_2p96>; |
| |
| cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <32 2>, /* ADSP */ |
| <48 4>; /* NFC */ |
| |
| sd_cd: sd-cd-state { |
| pins = "gpio91"; |
| function = "gpio"; |
| bias-pull-up; |
| }; |
| }; |
| |
| &uart5 { |
| status = "okay"; |
| }; |
| |
| &usb_1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_dwc3 { |
| /delete-property/ usb-role-switch; |
| dr_mode = "peripheral"; |
| }; |
| |
| &usb_1_hsphy { |
| vdda-pll-supply = <&vreg_l10c_0p88>; |
| vdda33-supply = <&vreg_l2b_3p072>; |
| vdda18-supply = <&vreg_l1c_1p8>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_qmpphy { |
| vdda-phy-supply = <&vreg_l6b_1p2>; |
| vdda-pll-supply = <&vreg_l1b_0p912>; |
| |
| status = "okay"; |
| }; |
| |
| &wifi { |
| memory-region = <&wlan_fw_mem>; |
| }; |
