| // SPDX-License-Identifier: BSD-3-Clause |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/sound/qcom,q6asm.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| |
| #include "sc7180.dtsi" |
| |
| #include "pm6150.dtsi" |
| #include "pm6150l.dtsi" |
| |
| /delete-node/ &tz_mem; |
| /delete-node/ &ipa_fw_mem; |
| |
| / { |
| model = "Acer Aspire 1"; |
| compatible = "acer,aspire1", "qcom,sc7180"; |
| chassis-type = "laptop"; |
| |
| aliases { |
| bluetooth0 = &bluetooth; |
| hsuart0 = &uart3; |
| serial0 = &uart8; |
| wifi0 = &wifi; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| reserved-memory { |
| zap_mem: zap-shader@80840000 { |
| reg = <0x0 0x80840000 0 0x2000>; |
| no-map; |
| }; |
| |
| venus_mem: venus@85b00000 { |
| reg = <0x0 0x85b00000 0 0x500000>; |
| no-map; |
| }; |
| |
| mpss_mem: mpss@86000000 { |
| reg = <0x0 0x86000000 0x0 0x2000000>; |
| no-map; |
| }; |
| |
| adsp_mem: adsp@8e400000 { |
| reg = <0x0 0x8e400000 0x0 0x2800000>; |
| no-map; |
| }; |
| |
| wlan_mem: wlan@93900000 { |
| reg = <0x0 0x93900000 0x0 0x200000>; |
| no-map; |
| }; |
| }; |
| |
| max98357a: audio-codec { |
| compatible = "maxim,max98357a"; |
| sdmode-gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-0 = <&_sd_mode_default>; |
| pinctrl-names = "default"; |
| |
| #sound-dai-cells = <0>; |
| }; |
| |
| backlight: backlight { |
| compatible = "pwm-backlight"; |
| pwms = <&sn65dsi86_bridge 1000000>; |
| enable-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-0 = <&soc_bkoff_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| reg_brij_1p2: bridge-1p2-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "brij_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| |
| gpio = <&tlmm 19 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <®_edp_1p2_en_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| reg_brij_1p8: bridge-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "brij_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| vin-supply = <&vreg_l8c_1p8>; |
| |
| gpio = <&tlmm 20 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <®_edp_1p8_en_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| reg_codec_3p3: codec-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "codec_3p3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 83 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <®_audio_en_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| reg_lcm_3p3: panel-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "lcm_3p3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <®_lcm_en_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| sound: sound { |
| compatible = "qcom,sc7180-qdsp6-sndcard"; |
| pinctrl-0 = <&pri_mi2s_active>, <&pri_mi2s_mclk_active>, <&ter_mi2s_active>; |
| pinctrl-names = "default"; |
| model = "Acer-Aspire-1"; |
| |
| audio-routing = |
| "Headphone Jack", "HPOL", |
| "Headphone Jack", "HPOR"; |
| |
| multimedia1-dai-link { |
| link-name = "MultiMedia1"; |
| |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; |
| }; |
| }; |
| |
| multimedia2-dai-link { |
| link-name = "MultiMedia2"; |
| |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; |
| }; |
| }; |
| |
| multimedia3-dai-link { |
| link-name = "MultiMedia3"; |
| |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; |
| }; |
| }; |
| |
| multimedia4-dai-link { |
| link-name = "MultiMedia4"; |
| |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA4>; |
| }; |
| }; |
| |
| primary-rx-dai-link { |
| link-name = "Primary MI2S Playback"; |
| |
| cpu { |
| sound-dai = <&q6afedai PRIMARY_MI2S_RX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&alc5682 0>; |
| }; |
| }; |
| |
| primary-tx-dai-link { |
| link-name = "Primary MI2S Capture"; |
| |
| cpu { |
| sound-dai = <&q6afedai PRIMARY_MI2S_TX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&alc5682 0>; |
| }; |
| }; |
| |
| tertiary-rx-dai-link { |
| link-name = "Tertiary MI2S Playback"; |
| |
| cpu { |
| sound-dai = <&q6afedai TERTIARY_MI2S_RX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&max98357a>; |
| }; |
| }; |
| |
| displayport-rx-dai-link { |
| link-name = "DisplayPort Playback"; |
| |
| cpu { |
| sound-dai = <&q6afedai DISPLAY_PORT_RX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&mdss_dp>; |
| }; |
| }; |
| }; |
| |
| reg_tp_3p3: touchpad-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "tp_3p3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <®_tp_en_default>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| embedded-controller@76 { |
| compatible = "acer,aspire1-ec"; |
| reg = <0x76>; |
| |
| interrupts-extended = <&tlmm 30 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-0 = <&ec_int_default>; |
| pinctrl-names = "default"; |
| |
| connector { |
| compatible = "usb-c-connector"; |
| |
| port { |
| ec_dp_in: endpoint { |
| remote-endpoint = <&mdss_dp_out>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c4 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| /* |
| * NOTE: DSDT defines two possible touchpads, other one is |
| * |
| * reg = <0x15>; |
| * hid-descr-addr = <0x1>; |
| */ |
| |
| touchpad@2c { |
| compatible = "hid-over-i2c"; |
| reg = <0x2c>; |
| hid-descr-addr = <0x20>; |
| |
| vdd-supply = <®_tp_3p3>; |
| |
| interrupts-extended = <&tlmm 94 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-0 = <&hid_touchpad_default>; |
| pinctrl-names = "default"; |
| |
| wakeup-source; |
| }; |
| |
| keyboard@3a { |
| compatible = "hid-over-i2c"; |
| reg = <0x3a>; |
| hid-descr-addr = <0x1>; |
| |
| interrupts-extended = <&tlmm 33 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-0 = <&hid_keyboard_default>; |
| pinctrl-names = "default"; |
| |
| wakeup-source; |
| }; |
| }; |
| |
| &i2c9 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| alc5682: codec@1a { |
| compatible = "realtek,rt5682i"; |
| reg = <0x1a>; |
| |
| #sound-dai-cells = <1>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <28 IRQ_TYPE_EDGE_BOTH>; |
| |
| pinctrl-0 = <&codec_irq_default>; |
| pinctrl-names = "default"; |
| |
| AVDD-supply = <&vreg_l15a_1p8>; |
| MICVDD-supply = <®_codec_3p3>; |
| VBAT-supply = <®_codec_3p3>; |
| DBVDD-supply = <&vreg_l15a_1p8>; |
| LDO1-IN-supply = <&vreg_l15a_1p8>; |
| |
| /* |
| * NOTE: The board has a path from this codec to the |
| * DMIC microphones in the lid, however some of the option |
| * resistors are absent and the microphones are connected |
| * to the SoC instead. |
| * |
| * If the resistors were to be changed by the user to |
| * connect the codec, the following could be used: |
| * |
| * realtek,dmic1-data-pin = <1>; |
| * realtek,dmic1-clk-pin = <1>; |
| */ |
| |
| realtek,jd-src = <1>; |
| }; |
| }; |
| |
| &i2c10 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| sn65dsi86_bridge: bridge@2c { |
| compatible = "ti,sn65dsi86"; |
| reg = <0x2c>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| #pwm-cells = <1>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; |
| |
| enable-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>; |
| suspend-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-0 = <&bridge_en_default>, |
| <&edp_bridge_irq_default>, |
| <&bridge_suspend_default>; |
| pinctrl-names = "default"; |
| |
| vpll-supply = <®_brij_1p8>; |
| vccio-supply = <®_brij_1p8>; |
| vcca-supply = <®_brij_1p2>; |
| vcc-supply = <®_brij_1p2>; |
| |
| clocks = <&rpmhcc RPMH_LN_BB_CLK3>; |
| clock-names = "refclk"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| sn65dsi86_in: endpoint { |
| remote-endpoint = <&mdss_dsi0_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| sn65dsi86_out: endpoint { |
| data-lanes = <0 1>; |
| remote-endpoint = <&panel_in_edp>; |
| }; |
| }; |
| }; |
| |
| aux-bus { |
| panel: panel { |
| compatible = "edp-panel"; |
| power-supply = <®_lcm_3p3>; |
| backlight = <&backlight>; |
| hpd-absent-delay-ms = <200>; |
| |
| port { |
| panel_in_edp: endpoint { |
| remote-endpoint = <&sn65dsi86_out>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| memory-region = <&zap_mem>; |
| firmware-name = "qcom/sc7180/acer/aspire1/qcdxkmsuc7180.mbn"; |
| }; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dp { |
| data-lanes = <0 1>; |
| |
| vdda-1p2-supply = <&vreg_l3c_1p2>; |
| vdda-0p9-supply = <&vreg_l4a_0p8>; |
| |
| status = "okay"; |
| }; |
| |
| &mdss_dp_out { |
| remote-endpoint = <&ec_dp_in>; |
| }; |
| |
| &mdss_dsi0 { |
| vdda-supply = <&vreg_l3c_1p2>; |
| status = "okay"; |
| }; |
| |
| &mdss_dsi0_out { |
| remote-endpoint = <&sn65dsi86_in>; |
| data-lanes = <0 1 2 3>; |
| }; |
| |
| &mdss_dsi0_phy { |
| vdds-supply = <&vreg_l4a_0p8>; |
| status = "okay"; |
| }; |
| |
| &pm6150_adc { |
| channel@4e { |
| reg = <ADC5_AMUX_THM2_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| label = "thermistor"; |
| }; |
| |
| channel@4f { |
| reg = <ADC5_AMUX_THM3_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| label = "charger_thermistor"; |
| }; |
| }; |
| |
| &pm6150_adc_tm { |
| status = "okay"; |
| |
| charger-thermistor@0 { |
| reg = <0>; |
| io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| thermistor@1 { |
| reg = <1>; |
| io-channels = <&pm6150_adc ADC5_AMUX_THM2_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| }; |
| |
| &pm6150_pon { |
| status = "disabled"; |
| }; |
| |
| &pm6150_rtc { |
| status = "okay"; |
| }; |
| |
| &q6afedai { |
| dai@16 { |
| reg = <PRIMARY_MI2S_RX>; |
| qcom,sd-lines = <1>; |
| }; |
| |
| dai@17 { |
| reg = <PRIMARY_MI2S_TX>; |
| qcom,sd-lines = <0>; |
| }; |
| |
| dai@20 { |
| reg = <TERTIARY_MI2S_RX>; |
| qcom,sd-lines = <0>; |
| }; |
| |
| dai@104 { |
| reg = <DISPLAY_PORT_RX>; |
| }; |
| }; |
| |
| &q6asmdai { |
| dai@0 { |
| reg = <0>; |
| }; |
| |
| dai@1 { |
| reg = <1>; |
| }; |
| |
| dai@2 { |
| reg = <2>; |
| }; |
| |
| dai@3 { |
| reg = <3>; |
| }; |
| }; |
| |
| &qupv3_id_0 { |
| status = "okay"; |
| }; |
| |
| &qupv3_id_1 { |
| status = "okay"; |
| }; |
| |
| &remoteproc_adsp { |
| memory-region = <&adsp_mem>; |
| firmware-name = "qcom/sc7180/acer/aspire1/qcadsp7180.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_mpss { |
| firmware-name = "qcom/sc7180/acer/aspire1/qcmpss7180_nm.mbn"; |
| status = "okay"; |
| }; |
| |
| &sdhc_1 { |
| pinctrl-0 = <&sdc1_default>; |
| pinctrl-1 = <&sdc1_sleep>; |
| pinctrl-names = "default", "sleep"; |
| vmmc-supply = <&vreg_l19a_2p9>; |
| vqmmc-supply = <&vreg_l12a_1p8>; |
| |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| /delete-property/interrupts; |
| interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>, |
| <&tlmm 41 IRQ_TYPE_EDGE_FALLING>; |
| |
| pinctrl-1 = <&qup_uart3_sleep>; |
| pinctrl-names = "default", "sleep"; |
| |
| status = "okay"; |
| |
| bluetooth: bluetooth { |
| compatible = "qcom,wcn3991-bt"; |
| vddio-supply = <&vreg_l10a_1p8>; |
| vddxo-supply = <&vreg_l1c_1p8>; |
| vddrf-supply = <&vreg_l2c_1p3>; |
| vddch0-supply = <&vreg_l10c_3p3>; |
| max-speed = <3200000>; |
| }; |
| }; |
| |
| &uart8 { |
| status = "okay"; |
| }; |
| |
| &usb_1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_dwc3 { |
| dr_mode = "host"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| usb_hub_2_x: hub@1 { |
| compatible = "usbbda,5411"; |
| reg = <1>; |
| peer-hub = <&usb_hub_3_x>; |
| }; |
| |
| usb_hub_3_x: hub@2 { |
| compatible = "usbbda,411"; |
| reg = <2>; |
| peer-hub = <&usb_hub_2_x>; |
| }; |
| }; |
| |
| &usb_1_hsphy { |
| vdd-supply = <&vreg_l4a_0p8>; |
| vdda-pll-supply = <&vreg_l11a_1p8>; |
| vdda-phy-dpdm-supply = <&vreg_l17a_3p0>; |
| qcom,imp-res-offset-value = <8>; |
| qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>; |
| qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; |
| qcom,bias-ctrl-value = <0x22>; |
| qcom,charge-ctrl-value = <3>; |
| qcom,hsdisc-trim-value = <0>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_qmpphy { |
| vdda-phy-supply = <&vreg_l3c_1p2>; |
| vdda-pll-supply = <&vreg_l4a_0p8>; |
| |
| status = "okay"; |
| }; |
| |
| &venus { |
| firmware-name = "qcom/sc7180/acer/aspire1/qcvss7180.mbn"; |
| }; |
| |
| &wifi { |
| vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>; |
| vdd-1.8-xo-supply = <&vreg_l1c_1p8>; |
| vdd-1.3-rfa-supply = <&vreg_l2c_1p3>; |
| vdd-3.3-ch0-supply = <&vreg_l10c_3p3>; |
| vdd-3.3-ch1-supply = <&vreg_l11c_3p3>; |
| |
| status = "okay"; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm6150-rpmh-regulators"; |
| qcom,pmic-id = "a"; |
| |
| vreg_s1a_1p1: smps1 { |
| regulator-min-microvolt = <1128000>; |
| regulator-max-microvolt = <1128000>; |
| }; |
| |
| vreg_l4a_0p8: ldo4 { |
| regulator-min-microvolt = <824000>; |
| regulator-max-microvolt = <928000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9a_0p6: ldo9 { |
| regulator-min-microvolt = <488000>; |
| regulator-max-microvolt = <800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10a_1p8: ldo10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| vreg_l11a_1p8: ldo11 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12a_1p8: ldo12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13a_1p8: ldo13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14a_1p8: ldo14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l15a_1p8: ldo15 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l16a_2p7: ldo16 { |
| regulator-min-microvolt = <2496000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l17a_3p0: ldo17 { |
| regulator-min-microvolt = <2920000>; |
| regulator-max-microvolt = <3232000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l18a_2p8: ldo18 { |
| regulator-min-microvolt = <2496000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l19a_2p9: ldo19 { |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm6150l-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vreg_s8c_1p3: smps8 { |
| regulator-min-microvolt = <1120000>; |
| regulator-max-microvolt = <1408000>; |
| }; |
| |
| vreg_l1c_1p8: ldo1 { |
| regulator-min-microvolt = <1616000>; |
| regulator-max-microvolt = <1984000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2c_1p3: ldo2 { |
| regulator-min-microvolt = <1168000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3c_1p2: ldo3 { |
| regulator-min-microvolt = <1144000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4c_1p8: ldo4 { |
| regulator-min-microvolt = <1648000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; |
| }; |
| |
| vreg_l5c_1p8: ldo5 { |
| regulator-min-microvolt = <1648000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; |
| }; |
| |
| vreg_l6c_2p9: ldo6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7c_3p0: ldo7 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3312000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; |
| }; |
| |
| vreg_l8c_1p8: ldo8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9c_2p9: ldo9 { |
| regulator-min-microvolt = <2952000>; |
| regulator-max-microvolt = <2952000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10c_3p3: ldo10 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l11c_3p3: ldo11 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_bob: bob { |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; |
| }; |
| }; |
| }; |
| |
| &qup_i2c2_default { |
| drive-strength = <2>; |
| |
| /* Has external pullup */ |
| bias-disable; |
| }; |
| |
| &qup_i2c4_default { |
| drive-strength = <2>; |
| |
| /* Has external pullup */ |
| bias-disable; |
| }; |
| |
| &qup_i2c9_default { |
| drive-strength = <2>; |
| |
| /* Has external pullup */ |
| bias-disable; |
| }; |
| |
| &qup_i2c10_default { |
| drive-strength = <2>; |
| |
| /* Has external pullup */ |
| bias-disable; |
| }; |
| |
| &tlmm { |
| /* |
| * The TZ seem to protect those because some boards can have |
| * fingerprint sensor connected to this range. Not connected |
| * on this board |
| */ |
| gpio-reserved-ranges = <58 5>; |
| |
| amp_sd_mode_default: amp-sd-mode-deault-state { |
| pins = "gpio23"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| bridge_en_default: bridge-en-default-state { |
| pins = "gpio51"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| bridge_suspend_default: bridge-suspend-default-state { |
| pins = "gpio22"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-pull-up; |
| }; |
| |
| codec_irq_default: codec-irq-deault-state { |
| pins = "gpio28"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| ec_int_default: ec-int-default-state { |
| pins = "gpio30"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| edp_bridge_irq_default: edp-bridge-irq-default-state { |
| pins = "gpio11"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| hid_keyboard_default: hid-keyboard-default-state { |
| pins = "gpio33"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| hid_touchpad_default: hid-touchpad-default-state { |
| pins = "gpio94"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| qup_uart3_sleep: qup-uart3-sleep-state { |
| cts-pins { |
| /* |
| * Configure a pull-down on CTS to match the pull of |
| * the Bluetooth module. |
| */ |
| pins = "gpio38"; |
| function = "gpio"; |
| bias-pull-down; |
| }; |
| |
| rts-pins { |
| /* |
| * Configure pull-down on RTS. As RTS is active low |
| * signal, pull it low to indicate the BT SoC that it |
| * can wakeup the system anytime from suspend state by |
| * pulling RX low (by sending wakeup bytes). |
| */ |
| pins = "gpio39"; |
| function = "gpio"; |
| bias-pull-down; |
| }; |
| |
| tx-pins { |
| /* |
| * Configure pull-up on TX when it isn't actively driven |
| * to prevent BT SoC from receiving garbage during sleep. |
| */ |
| pins = "gpio40"; |
| function = "gpio"; |
| bias-pull-up; |
| }; |
| |
| rx-pins { |
| /* |
| * Configure a pull-up on RX. This is needed to avoid |
| * garbage data when the TX pin of the Bluetooth module |
| * is floating which may cause spurious wakeups. |
| */ |
| pins = "gpio41"; |
| function = "gpio"; |
| bias-pull-up; |
| }; |
| }; |
| |
| reg_edp_1p2_en_default: reg-edp-1p2-en-deault-state { |
| pins = "gpio19"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| reg_edp_1p8_en_default: reg-edp-1p8-en-deault-state { |
| pins = "gpio20"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| reg_lcm_en_default: reg-lcm-en-deault-state { |
| pins = "gpio26"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| reg_audio_en_default: reg-audio-en-deault-state { |
| pins = "gpio83"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| reg_tp_en_default: reg-tp-en-deault-state { |
| pins = "gpio25"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| soc_bkoff_default: soc-bkoff-deault-state { |
| pins = "gpio10"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| sdc1_default: sdc1-default-state { |
| clk-pins { |
| pins = "sdc1_clk"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| cmd-pins { |
| pins = "sdc1_cmd"; |
| drive-strength = <16>; |
| bias-pull-up; |
| }; |
| |
| data-pins { |
| pins = "sdc1_data"; |
| drive-strength = <16>; |
| bias-pull-up; |
| }; |
| |
| rclk-pins { |
| pins = "sdc1_rclk"; |
| bias-pull-down; |
| }; |
| }; |
| |
| sdc1_sleep: sdc1-sleep-state { |
| clk-pins { |
| pins = "sdc1_clk"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| cmd-pins { |
| pins = "sdc1_cmd"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| data-pins { |
| pins = "sdc1_data"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| rclk-pins { |
| pins = "sdc1_rclk"; |
| bias-pull-down; |
| }; |
| }; |
| }; |
