| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. |
| * Copyright (c) 2021-2023, Linaro Limited |
| */ |
| |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/spmi/spmi.h> |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| |
| / { |
| thermal-zones { |
| pmc8180-thermal { |
| polling-delay-passive = <100>; |
| |
| thermal-sensors = <&pmc8180_temp>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| |
| trip2 { |
| temperature = <145000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| pmc8180c-thermal { |
| polling-delay-passive = <100>; |
| |
| thermal-sensors = <&pmc8180c_temp>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| |
| trip2 { |
| temperature = <145000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &spmi_bus { |
| pmc8180_0: pmic@0 { |
| compatible = "qcom,pm8150", "qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pon: pon@800 { |
| compatible = "qcom,pm8916-pon"; |
| reg = <0x0800>; |
| pmc8180_pwrkey: pwrkey { |
| compatible = "qcom,pm8941-pwrkey"; |
| interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| bias-pull-up; |
| linux,code = <KEY_POWER>; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| pmc8180_temp: temp-alarm@2400 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0x2400>; |
| interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; |
| io-channels = <&pmc8180_adc ADC5_DIE_TEMP>; |
| io-channel-names = "thermal"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmc8180_adc: adc@3100 { |
| compatible = "qcom,spmi-adc5"; |
| reg = <0x3100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| |
| channel@0 { |
| reg = <ADC5_REF_GND>; |
| qcom,pre-scaling = <1 1>; |
| label = "ref_gnd"; |
| }; |
| |
| channel@1 { |
| reg = <ADC5_1P25VREF>; |
| qcom,pre-scaling = <1 1>; |
| label = "vref_1p25"; |
| }; |
| |
| channel@6 { |
| reg = <ADC5_DIE_TEMP>; |
| qcom,pre-scaling = <1 1>; |
| label = "die_temp"; |
| }; |
| }; |
| |
| pmc8180_adc_tm: adc-tm@3500 { |
| compatible = "qcom,spmi-adc-tm5"; |
| reg = <0x3500>; |
| interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; |
| #thermal-sensor-cells = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| rtc@6000 { |
| compatible = "qcom,pm8941-rtc"; |
| reg = <0x6000>; |
| reg-names = "rtc", "alarm"; |
| interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; |
| }; |
| |
| pmc8180_1_gpios: gpio@c000 { |
| compatible = "qcom,pmc8180-gpio", "qcom,spmi-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| gpio-ranges = <&pmc8180_1_gpios 0 0 10>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmic@1 { |
| compatible = "qcom,pmc8180", "qcom,spmi-pmic"; |
| reg = <0x1 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| pmic@2 { |
| compatible = "qcom,smb2351", "qcom,spmi-pmic"; |
| reg = <0x2 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| adc@3100 { |
| compatible = "qcom,spmi-adc-rev2"; |
| reg = <0x3100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| |
| channel@0 { |
| reg = <ADC5_REF_GND>; |
| qcom,pre-scaling = <1 1>; |
| label = "ref_gnd"; |
| }; |
| |
| channel@1 { |
| reg = <ADC5_1P25VREF>; |
| qcom,pre-scaling = <1 1>; |
| label = "vref_1p25"; |
| }; |
| |
| channel@85 { |
| reg = <0x85>; |
| qcom,pre-scaling = <1 1>; |
| label = "vcoin2"; |
| }; |
| }; |
| }; |
| |
| pmic@6 { |
| compatible = "qcom,pm8150c", "qcom,spmi-pmic"; |
| reg = <0x6 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| pmc8180_2: pmic@8 { |
| compatible = "qcom,pm8150", "qcom,spmi-pmic"; |
| reg = <0x8 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmc8180_2_gpios: gpio@c000 { |
| compatible = "qcom,pmc8180-gpio", "qcom,spmi-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| gpio-ranges = <&pmc8180_2_gpios 0 0 10>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmic@a { |
| compatible = "qcom,smb2351", "qcom,spmi-pmic"; |
| reg = <0xa SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| adc@3100 { |
| compatible = "qcom,spmi-adc-rev2"; |
| reg = <0x3100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| interrupts = <0xa 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| |
| channel@0 { |
| reg = <ADC5_REF_GND>; |
| qcom,pre-scaling = <1 1>; |
| label = "ref_gnd"; |
| }; |
| |
| channel@1 { |
| reg = <ADC5_1P25VREF>; |
| qcom,pre-scaling = <1 1>; |
| label = "vref_1p25"; |
| }; |
| |
| channel@85 { |
| reg = <0x85>; |
| qcom,pre-scaling = <1 1>; |
| label = "vcoin"; |
| }; |
| }; |
| }; |
| |
| pmic@4 { |
| compatible = "qcom,pm8150c", "qcom,spmi-pmic"; |
| reg = <0x4 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pon@800 { |
| compatible = "qcom,pm8916-pon"; |
| reg = <0x0800>; |
| |
| status = "disabled"; |
| }; |
| |
| pmc8180c_temp: temp-alarm@2400 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0x2400>; |
| interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; |
| io-channels = <&pmc8180c_adc ADC5_DIE_TEMP>; |
| io-channel-names = "thermal"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmc8180c_adc: adc@3100 { |
| compatible = "qcom,spmi-adc5"; |
| reg = <0x3100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| |
| channel@0 { |
| reg = <ADC5_REF_GND>; |
| qcom,pre-scaling = <1 1>; |
| label = "ref_gnd"; |
| }; |
| |
| channel@1 { |
| reg = <ADC5_1P25VREF>; |
| qcom,pre-scaling = <1 1>; |
| label = "vref_1p25"; |
| }; |
| |
| channel@6 { |
| reg = <ADC5_DIE_TEMP>; |
| qcom,pre-scaling = <1 1>; |
| label = "die_temp"; |
| }; |
| }; |
| |
| pmc8180c_adc_tm: adc-tm@3500 { |
| compatible = "qcom,spmi-adc-tm5"; |
| reg = <0x3500>; |
| interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; |
| #thermal-sensor-cells = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| pmc8180c_gpios: gpio@c000 { |
| compatible = "qcom,pmc8180c-gpio", "qcom,spmi-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| gpio-ranges = <&pmc8180c_gpios 0 0 12>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmic@5 { |
| compatible = "qcom,pmc8180c", "qcom,spmi-pmic"; |
| reg = <0x5 SPMI_USID>; |
| |
| pmc8180c_lpg: pwm { |
| compatible = "qcom,pmc8180c-lpg"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #pwm-cells = <2>; |
| |
| status = "disabled"; |
| }; |
| }; |
| }; |
