arch/arm64/boot/dts/qcom/sc8280xp.dtsi

// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2021, The Linux Foundation. All rights reserved.
 * Copyright (c) 2022, Linaro Limited
 */

#include <dt-bindings/clock/qcom,dispcc-sc8280xp.h>
#include <dt-bindings/clock/qcom,gcc-sc8280xp.h>
#include <dt-bindings/clock/qcom,gpucc-sc8280xp.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/clock/qcom,sc8280xp-camcc.h>
#include <dt-bindings/clock/qcom,sc8280xp-lpasscc.h>
#include <dt-bindings/interconnect/qcom,osm-l3.h>
#include <dt-bindings/interconnect/qcom,sc8280xp.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/phy/phy-qcom-qmp.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,gpr.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include <dt-bindings/sound/qcom,q6afe.h>
#include <dt-bindings/thermal/thermal.h>

/ {
	interrupt-parent = <&intc>;

	#address-cells = <2>;
	#size-cells = <2>;

	clocks {
		xo_board_clk: xo-board-clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
		};

		sleep_clk: sleep-clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <32764>;
		};
	};

	cpus {
		#address-cells = <2>;
		#size-cells = <0>;

		CPU0: cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-a78c";
			reg = <0x0 0x0>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			capacity-dmips-mhz = <981>;
			dynamic-power-coefficient = <549>;
			next-level-cache = <&L2_0>;
			power-domains = <&CPU_PD0>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_0: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
				L3_0: l3-cache {
					compatible = "cache";
					cache-level = <3>;
					cache-unified;
				};
			};
		};

		CPU1: cpu@100 {
			device_type = "cpu";
			compatible = "arm,cortex-a78c";
			reg = <0x0 0x100>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			capacity-dmips-mhz = <981>;
			dynamic-power-coefficient = <549>;
			next-level-cache = <&L2_100>;
			power-domains = <&CPU_PD1>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_100: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU2: cpu@200 {
			device_type = "cpu";
			compatible = "arm,cortex-a78c";
			reg = <0x0 0x200>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			capacity-dmips-mhz = <981>;
			dynamic-power-coefficient = <549>;
			next-level-cache = <&L2_200>;
			power-domains = <&CPU_PD2>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_200: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU3: cpu@300 {
			device_type = "cpu";
			compatible = "arm,cortex-a78c";
			reg = <0x0 0x300>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			capacity-dmips-mhz = <981>;
			dynamic-power-coefficient = <549>;
			next-level-cache = <&L2_300>;
			power-domains = <&CPU_PD3>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_300: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU4: cpu@400 {
			device_type = "cpu";
			compatible = "arm,cortex-x1c";
			reg = <0x0 0x400>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <590>;
			next-level-cache = <&L2_400>;
			power-domains = <&CPU_PD4>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_400: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU5: cpu@500 {
			device_type = "cpu";
			compatible = "arm,cortex-x1c";
			reg = <0x0 0x500>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <590>;
			next-level-cache = <&L2_500>;
			power-domains = <&CPU_PD5>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_500: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU6: cpu@600 {
			device_type = "cpu";
			compatible = "arm,cortex-x1c";
			reg = <0x0 0x600>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <590>;
			next-level-cache = <&L2_600>;
			power-domains = <&CPU_PD6>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_600: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU7: cpu@700 {
			device_type = "cpu";
			compatible = "arm,cortex-x1c";
			reg = <0x0 0x700>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <590>;
			next-level-cache = <&L2_700>;
			power-domains = <&CPU_PD7>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_700: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		cpu-map {
			cluster0 {
				core0 {
					cpu = <&CPU0>;
				};

				core1 {
					cpu = <&CPU1>;
				};

				core2 {
					cpu = <&CPU2>;
				};

				core3 {
					cpu = <&CPU3>;
				};

				core4 {
					cpu = <&CPU4>;
				};

				core5 {
					cpu = <&CPU5>;
				};

				core6 {
					cpu = <&CPU6>;
				};

				core7 {
					cpu = <&CPU7>;
				};
			};
		};

		idle-states {
			entry-method = "psci";

			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
				compatible = "arm,idle-state";
				idle-state-name = "little-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <355>;
				exit-latency-us = <909>;
				min-residency-us = <3934>;
				local-timer-stop;
			};

			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
				compatible = "arm,idle-state";
				idle-state-name = "big-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <241>;
				exit-latency-us = <1461>;
				min-residency-us = <4488>;
				local-timer-stop;
			};
		};

		domain-idle-states {
			CLUSTER_SLEEP_0: cluster-sleep-0 {
				compatible = "domain-idle-state";
				arm,psci-suspend-param = <0x4100c344>;
				entry-latency-us = <3263>;
				exit-latency-us = <6562>;
				min-residency-us = <9987>;
			};
		};
	};

	firmware {
		scm: scm {
			compatible = "qcom,scm-sc8280xp", "qcom,scm";
			interconnects = <&aggre2_noc MASTER_CRYPTO 0 &mc_virt SLAVE_EBI1 0>;
			qcom,dload-mode = <&tcsr 0x13000>;
		};
	};

	aggre1_noc: interconnect-aggre1-noc {
		compatible = "qcom,sc8280xp-aggre1-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	aggre2_noc: interconnect-aggre2-noc {
		compatible = "qcom,sc8280xp-aggre2-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	clk_virt: interconnect-clk-virt {
		compatible = "qcom,sc8280xp-clk-virt";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	config_noc: interconnect-config-noc {
		compatible = "qcom,sc8280xp-config-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	dc_noc: interconnect-dc-noc {
		compatible = "qcom,sc8280xp-dc-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	gem_noc: interconnect-gem-noc {
		compatible = "qcom,sc8280xp-gem-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	lpass_noc: interconnect-lpass-ag-noc {
		compatible = "qcom,sc8280xp-lpass-ag-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	mc_virt: interconnect-mc-virt {
		compatible = "qcom,sc8280xp-mc-virt";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	mmss_noc: interconnect-mmss-noc {
		compatible = "qcom,sc8280xp-mmss-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	nspa_noc: interconnect-nspa-noc {
		compatible = "qcom,sc8280xp-nspa-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	nspb_noc: interconnect-nspb-noc {
		compatible = "qcom,sc8280xp-nspb-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	system_noc: interconnect-system-noc {
		compatible = "qcom,sc8280xp-system-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	memory@80000000 {
		device_type = "memory";
		/* We expect the bootloader to fill in the size */
		reg = <0x0 0x80000000 0x0 0x0>;
	};

	cpu0_opp_table: opp-table-cpu0 {
		compatible = "operating-points-v2";
		opp-shared;

		opp-300000000 {
			opp-hz = /bits/ 64 <300000000>;
			opp-peak-kBps = <(300000 * 32)>;
		};
		opp-403200000 {
			opp-hz = /bits/ 64 <403200000>;
			opp-peak-kBps = <(384000 * 32)>;
		};
		opp-499200000 {
			opp-hz = /bits/ 64 <499200000>;
			opp-peak-kBps = <(480000 * 32)>;
		};
		opp-595200000 {
			opp-hz = /bits/ 64 <595200000>;
			opp-peak-kBps = <(576000 * 32)>;
		};
		opp-691200000 {
			opp-hz = /bits/ 64 <691200000>;
			opp-peak-kBps = <(672000 * 32)>;
		};
		opp-806400000 {
			opp-hz = /bits/ 64 <806400000>;
			opp-peak-kBps = <(768000 * 32)>;
		};
		opp-902400000 {
			opp-hz = /bits/ 64 <902400000>;
			opp-peak-kBps = <(864000 * 32)>;
		};
		opp-1017600000 {
			opp-hz = /bits/ 64 <1017600000>;
			opp-peak-kBps = <(960000 * 32)>;
		};
		opp-1113600000 {
			opp-hz = /bits/ 64 <1113600000>;
			opp-peak-kBps = <(1075200 * 32)>;
		};
		opp-1209600000 {
			opp-hz = /bits/ 64 <1209600000>;
			opp-peak-kBps = <(1171200 * 32)>;
		};
		opp-1324800000 {
			opp-hz = /bits/ 64 <1324800000>;
			opp-peak-kBps = <(1267200 * 32)>;
		};
		opp-1440000000 {
			opp-hz = /bits/ 64 <1440000000>;
			opp-peak-kBps = <(1363200 * 32)>;
		};
		opp-1555200000 {
			opp-hz = /bits/ 64 <1555200000>;
			opp-peak-kBps = <(1536000 * 32)>;
		};
		opp-1670400000 {
			opp-hz = /bits/ 64 <1670400000>;
			opp-peak-kBps = <(1612800 * 32)>;
		};
		opp-1785600000 {
			opp-hz = /bits/ 64 <1785600000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-1881600000 {
			opp-hz = /bits/ 64 <1881600000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-1996800000 {
			opp-hz = /bits/ 64 <1996800000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2112000000 {
			opp-hz = /bits/ 64 <2112000000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2227200000 {
			opp-hz = /bits/ 64 <2227200000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2342400000 {
			opp-hz = /bits/ 64 <2342400000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2438400000 {
			opp-hz = /bits/ 64 <2438400000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
	};

	cpu4_opp_table: opp-table-cpu4 {
		compatible = "operating-points-v2";
		opp-shared;

		opp-825600000 {
			opp-hz = /bits/ 64 <825600000>;
			opp-peak-kBps = <(768000 * 32)>;
		};
		opp-940800000 {
			opp-hz = /bits/ 64 <940800000>;
			opp-peak-kBps = <(864000 * 32)>;
		};
		opp-1056000000 {
			opp-hz = /bits/ 64 <1056000000>;
			opp-peak-kBps = <(960000 * 32)>;
		};
		opp-1171200000 {
			opp-hz = /bits/ 64 <1171200000>;
			opp-peak-kBps = <(1171200 * 32)>;
		};
		opp-1286400000 {
			opp-hz = /bits/ 64 <1286400000>;
			opp-peak-kBps = <(1267200 * 32)>;
		};
		opp-1401600000 {
			opp-hz = /bits/ 64 <1401600000>;
			opp-peak-kBps = <(1363200 * 32)>;
		};
		opp-1516800000 {
			opp-hz = /bits/ 64 <1516800000>;
			opp-peak-kBps = <(1459200 * 32)>;
		};
		opp-1632000000 {
			opp-hz = /bits/ 64 <1632000000>;
			opp-peak-kBps = <(1612800 * 32)>;
		};
		opp-1747200000 {
			opp-hz = /bits/ 64 <1747200000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-1862400000 {
			opp-hz = /bits/ 64 <1862400000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-1977600000 {
			opp-hz = /bits/ 64 <1977600000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2073600000 {
			opp-hz = /bits/ 64 <2073600000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2169600000 {
			opp-hz = /bits/ 64 <2169600000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2284800000 {
			opp-hz = /bits/ 64 <2284800000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2400000000 {
			opp-hz = /bits/ 64 <2400000000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2496000000 {
			opp-hz = /bits/ 64 <2496000000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2592000000 {
			opp-hz = /bits/ 64 <2592000000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2688000000 {
			opp-hz = /bits/ 64 <2688000000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2803200000 {
			opp-hz = /bits/ 64 <2803200000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2899200000 {
			opp-hz = /bits/ 64 <2899200000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2995200000 {
			opp-hz = /bits/ 64 <2995200000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
	};

	qup_opp_table_100mhz: opp-table-qup100mhz {
		compatible = "operating-points-v2";

		opp-75000000 {
			opp-hz = /bits/ 64 <75000000>;
			required-opps = <&rpmhpd_opp_low_svs>;
		};

		opp-100000000 {
			opp-hz = /bits/ 64 <100000000>;
			required-opps = <&rpmhpd_opp_svs>;
		};
	};

	pmu {
		compatible = "arm,armv8-pmuv3";
		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
	};

	psci {
		compatible = "arm,psci-1.0";
		method = "smc";

		CPU_PD0: power-domain-cpu0 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD1: power-domain-cpu1 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD2: power-domain-cpu2 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD3: power-domain-cpu3 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD4: power-domain-cpu4 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD5: power-domain-cpu5 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD6: power-domain-cpu6 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD7: power-domain-cpu7 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CLUSTER_PD: power-domain-cpu-cluster0 {
			#power-domain-cells = <0>;
			domain-idle-states = <&CLUSTER_SLEEP_0>;
		};
	};

	reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		reserved-region@80000000 {
			reg = <0 0x80000000 0 0x860000>;
			no-map;
		};

		cmd_db: cmd-db-region@80860000 {
			compatible = "qcom,cmd-db";
			reg = <0 0x80860000 0 0x20000>;
			no-map;
		};

		reserved-region@80880000 {
			reg = <0 0x80880000 0 0x80000>;
			no-map;
		};

		smem_mem: smem-region@80900000 {
			compatible = "qcom,smem";
			reg = <0 0x80900000 0 0x200000>;
			no-map;
			hwlocks = <&tcsr_mutex 3>;
		};

		reserved-region@80b00000 {
			reg = <0 0x80b00000 0 0x100000>;
			no-map;
		};

		reserved-region@83b00000 {
			reg = <0 0x83b00000 0 0x1700000>;
			no-map;
		};

		reserved-region@85b00000 {
			reg = <0 0x85b00000 0 0xc00000>;
			no-map;
		};

		pil_adsp_mem: adsp-region@86c00000 {
			reg = <0 0x86c00000 0 0x2000000>;
			no-map;
		};

		pil_nsp0_mem: cdsp0-region@8a100000 {
			reg = <0 0x8a100000 0 0x1e00000>;
			no-map;
		};

		pil_nsp1_mem: cdsp1-region@8c600000 {
			reg = <0 0x8c600000 0 0x1e00000>;
			no-map;
		};

		reserved-region@aeb00000 {
			reg = <0 0xaeb00000 0 0x16600000>;
			no-map;
		};
	};

	smp2p-adsp {
		compatible = "qcom,smp2p";
		qcom,smem = <443>, <429>;
		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_LPASS
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <2>;

		smp2p_adsp_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_adsp_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-nsp0 {
		compatible = "qcom,smp2p";
		qcom,smem = <94>, <432>;
		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_CDSP
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <5>;

		smp2p_nsp0_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_nsp0_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-nsp1 {
		compatible = "qcom,smp2p";
		qcom,smem = <617>, <616>;
		interrupts-extended = <&ipcc IPCC_CLIENT_NSP1
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_NSP1
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <12>;

		smp2p_nsp1_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_nsp1_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	soc: soc@0 {
		compatible = "simple-bus";
		#address-cells = <2>;
		#size-cells = <2>;
		ranges = <0 0 0 0 0x10 0>;
		dma-ranges = <0 0 0 0 0x10 0>;

		ethernet0: ethernet@20000 {
			compatible = "qcom,sc8280xp-ethqos";
			reg = <0x0 0x00020000 0x0 0x10000>,
			      <0x0 0x00036000 0x0 0x100>;
			reg-names = "stmmaceth", "rgmii";

			clocks = <&gcc GCC_EMAC0_AXI_CLK>,
				 <&gcc GCC_EMAC0_SLV_AHB_CLK>,
				 <&gcc GCC_EMAC0_PTP_CLK>,
				 <&gcc GCC_EMAC0_RGMII_CLK>;
			clock-names = "stmmaceth",
				      "pclk",
				      "ptp_ref",
				      "rgmii";

			interrupts = <GIC_SPI 946 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 936 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "macirq", "eth_lpi";

			iommus = <&apps_smmu 0x4c0 0xf>;
			power-domains = <&gcc EMAC_0_GDSC>;

			snps,tso;
			snps,pbl = <32>;
			rx-fifo-depth = <4096>;
			tx-fifo-depth = <4096>;

			status = "disabled";
		};

		gcc: clock-controller@100000 {
			compatible = "qcom,gcc-sc8280xp";
			reg = <0x0 0x00100000 0x0 0x1f0000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&sleep_clk>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <&usb_0_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <&usb_1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <&pcie2a_phy>,
				 <&pcie2b_phy>,
				 <&pcie3a_phy>,
				 <&pcie3b_phy>,
				 <&pcie4_phy>,
				 <0>,
				 <0>;
			power-domains = <&rpmhpd SC8280XP_CX>;
		};

		ipcc: mailbox@408000 {
			compatible = "qcom,sc8280xp-ipcc", "qcom,ipcc";
			reg = <0 0x00408000 0 0x1000>;
			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-controller;
			#interrupt-cells = <3>;
			#mbox-cells = <2>;
		};

		qfprom: efuse@784000 {
			compatible = "qcom,sc8280xp-qfprom", "qcom,qfprom";
			reg = <0 0x00784000 0 0x3000>;
			#address-cells = <1>;
			#size-cells = <1>;

			gpu_speed_bin: gpu-speed-bin@18b {
				reg = <0x18b 0x1>;
				bits = <5 3>;
			};
		};

		qup2: geniqup@8c0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0 0x008c0000 0 0x2000>;
			clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
			clock-names = "m-ahb", "s-ahb";
			iommus = <&apps_smmu 0xa3 0>;

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";

			i2c16: i2c@880000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00880000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi16: spi@880000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00880000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c17: i2c@884000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00884000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi17: spi@884000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00884000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			uart17: serial@884000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00884000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c18: i2c@888000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00888000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi18: spi@888000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00888000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c19: i2c@88c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0088c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi19: spi@88c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0088c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c20: i2c@890000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00890000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi20: spi@890000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00890000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c21: i2c@894000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00894000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi21: spi@894000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00894000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c22: i2c@898000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00898000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
				interrupts = <GIC_SPI 833 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi22: spi@898000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00898000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 833 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c23: i2c@89c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0089c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>;
				interrupts = <GIC_SPI 834 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi23: spi@89c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0089c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 834 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
				                <&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};
		};

		qup0: geniqup@9c0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0 0x009c0000 0 0x6000>;
			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
			clock-names = "m-ahb", "s-ahb";
			iommus = <&apps_smmu 0x563 0>;

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";

			i2c0: i2c@980000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00980000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi0: spi@980000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00980000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c1: i2c@984000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00984000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi1: spi@984000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00984000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c2: i2c@988000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00988000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi2: spi@988000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00988000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			uart2: serial@988000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00988000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c3: i2c@98c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0098c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi3: spi@98c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0098c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c4: i2c@990000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00990000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi4: spi@990000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00990000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c5: i2c@994000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00994000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi5: spi@994000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00994000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c6: i2c@998000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00998000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi6: spi@998000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00998000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c7: i2c@99c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0099c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi7: spi@99c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0099c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};
		};

		qup1: geniqup@ac0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0 0x00ac0000 0 0x6000>;
			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
			clock-names = "m-ahb", "s-ahb";
			iommus = <&apps_smmu 0x83 0>;

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";

			i2c8: i2c@a80000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a80000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi8: spi@a80000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a80000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c9: i2c@a84000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a84000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi9: spi@a84000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a84000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c10: i2c@a88000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a88000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi10: spi@a88000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a88000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c11: i2c@a8c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a8c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi11: spi@a8c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a8c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c12: i2c@a90000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a90000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi12: spi@a90000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a90000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c13: i2c@a94000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a94000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi13: spi@a94000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a94000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c14: i2c@a98000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a98000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 835 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi14: spi@a98000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a98000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 835 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			i2c15: i2c@a9c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a9c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};

			spi15: spi@a9c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a9c000 0 0x4000>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
				                <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
				                <&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};
		};

		rng: rng@10d3000 {
			compatible = "qcom,prng-ee";
			reg = <0 0x010d3000 0 0x1000>;
			clocks = <&rpmhcc RPMH_HWKM_CLK>;
			clock-names = "core";
		};

		pcie4: pcie@1c00000 {
			device_type = "pci";
			compatible = "qcom,pcie-sc8280xp";
			reg = <0x0 0x01c00000 0x0 0x3000>,
			      <0x0 0x30000000 0x0 0xf1d>,
			      <0x0 0x30000f20 0x0 0xa8>,
			      <0x0 0x30001000 0x0 0x1000>,
			      <0x0 0x30100000 0x0 0x100000>,
			      <0x0 0x01c03000 0x0 0x1000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x00000000 0x0 0x30200000 0x0 0x100000>,
				 <0x02000000 0x0 0x30300000 0x0 0x30300000 0x0 0x1d00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <6>;
			num-lanes = <1>;

			msi-map = <0x0 &its 0xe0000 0x10000>;

			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_PCIE_4_AUX_CLK>,
				 <&gcc GCC_PCIE_4_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_4_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_4_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_4_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_4_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_SOUTH_SF_AXI_CLK>,
				 <&gcc GCC_CNOC_PCIE4_QX_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr_4",
				      "noc_aggr_south_sf",
				      "cnoc_qx";

			assigned-clocks = <&gcc GCC_PCIE_4_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			interconnects = <&aggre2_noc MASTER_PCIE_4 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_4 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			resets = <&gcc GCC_PCIE_4_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_4_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			phys = <&pcie4_phy>;
			phy-names = "pciephy";

			status = "disabled";

			pcie4_port0: pcie@0 {
				device_type = "pci";
				reg = <0x0 0x0 0x0 0x0 0x0>;
				bus-range = <0x01 0xff>;

				#address-cells = <3>;
				#size-cells = <2>;
				ranges;
			};
		};

		pcie4_phy: phy@1c06000 {
			compatible = "qcom,sc8280xp-qmp-gen3x1-pcie-phy";
			reg = <0x0 0x01c06000 0x0 0x2000>;

			clocks = <&gcc GCC_PCIE_4_AUX_CLK>,
				 <&gcc GCC_PCIE_4_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_4_CLKREF_CLK>,
				 <&gcc GCC_PCIE4_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_4_PIPE_CLK>,
				 <&gcc GCC_PCIE_4_PIPEDIV2_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe", "pipediv2";

			assigned-clocks = <&gcc GCC_PCIE4_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_4_GDSC>;

			resets = <&gcc GCC_PCIE_4_PHY_BCR>;
			reset-names = "phy";

			#clock-cells = <0>;
			clock-output-names = "pcie_4_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		pcie3b: pcie@1c08000 {
			device_type = "pci";
			compatible = "qcom,pcie-sc8280xp";
			reg = <0x0 0x01c08000 0x0 0x3000>,
			      <0x0 0x32000000 0x0 0xf1d>,
			      <0x0 0x32000f20 0x0 0xa8>,
			      <0x0 0x32001000 0x0 0x1000>,
			      <0x0 0x32100000 0x0 0x100000>,
			      <0x0 0x01c0b000 0x0 0x1000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x00000000 0x0 0x32200000 0x0 0x100000>,
				 <0x02000000 0x0 0x32300000 0x0 0x32300000 0x0 0x1d00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <5>;
			num-lanes = <2>;

			msi-map = <0x0 &its 0xd0000 0x10000>;

			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 526 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 GIC_SPI 527 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 GIC_SPI 528 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 GIC_SPI 529 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_PCIE_3B_AUX_CLK>,
				 <&gcc GCC_PCIE_3B_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_3B_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_3B_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_3B_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_4_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_SOUTH_SF_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr_4",
				      "noc_aggr_south_sf";

			assigned-clocks = <&gcc GCC_PCIE_3B_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			interconnects = <&aggre2_noc MASTER_PCIE_3B 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_3B 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			resets = <&gcc GCC_PCIE_3B_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_3B_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			phys = <&pcie3b_phy>;
			phy-names = "pciephy";

			status = "disabled";

			pcie3b_port0: pcie@0 {
				device_type = "pci";
				reg = <0x0 0x0 0x0 0x0 0x0>;
				bus-range = <0x01 0xff>;

				#address-cells = <3>;
				#size-cells = <2>;
				ranges;
			};
		};

		pcie3b_phy: phy@1c0e000 {
			compatible = "qcom,sc8280xp-qmp-gen3x2-pcie-phy";
			reg = <0x0 0x01c0e000 0x0 0x2000>;

			clocks = <&gcc GCC_PCIE_3B_AUX_CLK>,
				 <&gcc GCC_PCIE_3B_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_3A3B_CLKREF_CLK>,
				 <&gcc GCC_PCIE3B_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_3B_PIPE_CLK>,
				 <&gcc GCC_PCIE_3B_PIPEDIV2_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe", "pipediv2";

			assigned-clocks = <&gcc GCC_PCIE3B_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_3B_GDSC>;

			resets = <&gcc GCC_PCIE_3B_PHY_BCR>;
			reset-names = "phy";

			#clock-cells = <0>;
			clock-output-names = "pcie_3b_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		pcie3a: pcie@1c10000 {
			device_type = "pci";
			compatible = "qcom,pcie-sc8280xp";
			reg = <0x0 0x01c10000 0x0 0x3000>,
			      <0x0 0x34000000 0x0 0xf1d>,
			      <0x0 0x34000f20 0x0 0xa8>,
			      <0x0 0x34001000 0x0 0x1000>,
			      <0x0 0x34100000 0x0 0x100000>,
			      <0x0 0x01c13000 0x0 0x1000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x00000000 0x0 0x34200000 0x0 0x100000>,
				 <0x02000000 0x0 0x34300000 0x0 0x34300000 0x0 0x1d00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <4>;
			num-lanes = <4>;

			msi-map = <0x0 &its 0xc0000 0x10000>;

			interrupts = <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 499 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 GIC_SPI 542 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 GIC_SPI 543 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 GIC_SPI 544 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_PCIE_3A_AUX_CLK>,
				 <&gcc GCC_PCIE_3A_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_3A_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_3A_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_3A_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_4_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_SOUTH_SF_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr_4",
				      "noc_aggr_south_sf";

			assigned-clocks = <&gcc GCC_PCIE_3A_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			interconnects = <&aggre2_noc MASTER_PCIE_3A 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_3A 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			resets = <&gcc GCC_PCIE_3A_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_3A_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			phys = <&pcie3a_phy>;
			phy-names = "pciephy";

			status = "disabled";

			pcie3a_port0: pcie@0 {
				device_type = "pci";
				reg = <0x0 0x0 0x0 0x0 0x0>;
				bus-range = <0x01 0xff>;

				#address-cells = <3>;
				#size-cells = <2>;
				ranges;
			};
		};

		pcie3a_phy: phy@1c14000 {
			compatible = "qcom,sc8280xp-qmp-gen3x4-pcie-phy";
			reg = <0x0 0x01c14000 0x0 0x2000>,
			      <0x0 0x01c16000 0x0 0x2000>;

			clocks = <&gcc GCC_PCIE_3A_AUX_CLK>,
				 <&gcc GCC_PCIE_3A_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_3A3B_CLKREF_CLK>,
				 <&gcc GCC_PCIE3A_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_3A_PIPE_CLK>,
				 <&gcc GCC_PCIE_3A_PIPEDIV2_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe", "pipediv2";

			assigned-clocks = <&gcc GCC_PCIE3A_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_3A_GDSC>;

			resets = <&gcc GCC_PCIE_3A_PHY_BCR>;
			reset-names = "phy";

			qcom,4ln-config-sel = <&tcsr 0xa044 1>;

			#clock-cells = <0>;
			clock-output-names = "pcie_3a_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		pcie2b: pcie@1c18000 {
			device_type = "pci";
			compatible = "qcom,pcie-sc8280xp";
			reg = <0x0 0x01c18000 0x0 0x3000>,
			      <0x0 0x38000000 0x0 0xf1d>,
			      <0x0 0x38000f20 0x0 0xa8>,
			      <0x0 0x38001000 0x0 0x1000>,
			      <0x0 0x38100000 0x0 0x100000>,
			      <0x0 0x01c1b000 0x0 0x1000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x00000000 0x0 0x38200000 0x0 0x100000>,
				 <0x02000000 0x0 0x38300000 0x0 0x38300000 0x0 0x1d00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <3>;
			num-lanes = <2>;

			msi-map = <0x0 &its 0xb0000 0x10000>;

			interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 GIC_SPI 434 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 GIC_SPI 435 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 GIC_SPI 438 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_PCIE_2B_AUX_CLK>,
				 <&gcc GCC_PCIE_2B_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_2B_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_2B_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_2B_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_4_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_SOUTH_SF_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr_4",
				      "noc_aggr_south_sf";

			assigned-clocks = <&gcc GCC_PCIE_2B_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			interconnects = <&aggre2_noc MASTER_PCIE_2B 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_2B 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			resets = <&gcc GCC_PCIE_2B_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_2B_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			phys = <&pcie2b_phy>;
			phy-names = "pciephy";

			status = "disabled";

			pcie2b_port0: pcie@0 {
				device_type = "pci";
				reg = <0x0 0x0 0x0 0x0 0x0>;
				bus-range = <0x01 0xff>;

				#address-cells = <3>;
				#size-cells = <2>;
				ranges;
			};
		};

		pcie2b_phy: phy@1c1e000 {
			compatible = "qcom,sc8280xp-qmp-gen3x2-pcie-phy";
			reg = <0x0 0x01c1e000 0x0 0x2000>;

			clocks = <&gcc GCC_PCIE_2B_AUX_CLK>,
				 <&gcc GCC_PCIE_2B_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_2A2B_CLKREF_CLK>,
				 <&gcc GCC_PCIE2B_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_2B_PIPE_CLK>,
				 <&gcc GCC_PCIE_2B_PIPEDIV2_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe", "pipediv2";

			assigned-clocks = <&gcc GCC_PCIE2B_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_2B_GDSC>;

			resets = <&gcc GCC_PCIE_2B_PHY_BCR>;
			reset-names = "phy";

			#clock-cells = <0>;
			clock-output-names = "pcie_2b_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		pcie2a: pcie@1c20000 {
			device_type = "pci";
			compatible = "qcom,pcie-sc8280xp";
			reg = <0x0 0x01c20000 0x0 0x3000>,
			      <0x0 0x3c000000 0x0 0xf1d>,
			      <0x0 0x3c000f20 0x0 0xa8>,
			      <0x0 0x3c001000 0x0 0x1000>,
			      <0x0 0x3c100000 0x0 0x100000>,
			      <0x0 0x01c23000 0x0 0x1000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x00000000 0x0 0x3c200000 0x0 0x100000>,
				 <0x02000000 0x0 0x3c300000 0x0 0x3c300000 0x0 0x1d00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <2>;
			num-lanes = <4>;

			msi-map = <0x0 &its 0xa0000 0x10000>;

			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 523 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 524 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 525 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 530 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 GIC_SPI 531 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 GIC_SPI 532 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 GIC_SPI 533 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_PCIE_2A_AUX_CLK>,
				 <&gcc GCC_PCIE_2A_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_2A_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_2A_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_2A_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_4_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_SOUTH_SF_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr_4",
				      "noc_aggr_south_sf";

			assigned-clocks = <&gcc GCC_PCIE_2A_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			interconnects = <&aggre2_noc MASTER_PCIE_2A 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_2A 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			resets = <&gcc GCC_PCIE_2A_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_2A_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			phys = <&pcie2a_phy>;
			phy-names = "pciephy";

			status = "disabled";

			pcie2a_port0: pcie@0 {
				device_type = "pci";
				reg = <0x0 0x0 0x0 0x0 0x0>;
				bus-range = <0x01 0xff>;

				#address-cells = <3>;
				#size-cells = <2>;
				ranges;
			};
		};

		pcie2a_phy: phy@1c24000 {
			compatible = "qcom,sc8280xp-qmp-gen3x4-pcie-phy";
			reg = <0x0 0x01c24000 0x0 0x2000>,
			      <0x0 0x01c26000 0x0 0x2000>;

			clocks = <&gcc GCC_PCIE_2A_AUX_CLK>,
				 <&gcc GCC_PCIE_2A_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_2A2B_CLKREF_CLK>,
				 <&gcc GCC_PCIE2A_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_2A_PIPE_CLK>,
				 <&gcc GCC_PCIE_2A_PIPEDIV2_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe", "pipediv2";

			assigned-clocks = <&gcc GCC_PCIE2A_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_2A_GDSC>;

			resets = <&gcc GCC_PCIE_2A_PHY_BCR>;
			reset-names = "phy";

			qcom,4ln-config-sel = <&tcsr 0xa044 0>;

			#clock-cells = <0>;
			clock-output-names = "pcie_2a_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		ufs_mem_hc: ufs@1d84000 {
			compatible = "qcom,sc8280xp-ufshc", "qcom,ufshc",
				     "jedec,ufs-2.0";
			reg = <0 0x01d84000 0 0x3000>;
			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
			phys = <&ufs_mem_phy>;
			phy-names = "ufsphy";
			lanes-per-direction = <2>;
			#reset-cells = <1>;
			resets = <&gcc GCC_UFS_PHY_BCR>;
			reset-names = "rst";

			power-domains = <&gcc UFS_PHY_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			iommus = <&apps_smmu 0xe0 0x0>;
			dma-coherent;

			clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
				 <&gcc GCC_UFS_PHY_AHB_CLK>,
				 <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
				 <&gcc GCC_UFS_REF_CLKREF_CLK>,
				 <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
			clock-names = "core_clk",
				      "bus_aggr_clk",
				      "iface_clk",
				      "core_clk_unipro",
				      "ref_clk",
				      "tx_lane0_sync_clk",
				      "rx_lane0_sync_clk",
				      "rx_lane1_sync_clk";
			freq-table-hz = <75000000 300000000>,
					<0 0>,
					<0 0>,
					<75000000 300000000>,
					<0 0>,
					<0 0>,
					<0 0>,
					<0 0>;
			status = "disabled";
		};

		ufs_mem_phy: phy@1d87000 {
			compatible = "qcom,sc8280xp-qmp-ufs-phy";
			reg = <0 0x01d87000 0 0x1000>;

			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
				 <&gcc GCC_UFS_CARD_CLKREF_CLK>;
			clock-names = "ref",
				      "ref_aux",
				      "qref";

			power-domains = <&gcc UFS_PHY_GDSC>;

			resets = <&ufs_mem_hc 0>;
			reset-names = "ufsphy";

			#phy-cells = <0>;

			status = "disabled";
		};

		ufs_card_hc: ufs@1da4000 {
			compatible = "qcom,sc8280xp-ufshc", "qcom,ufshc",
				     "jedec,ufs-2.0";
			reg = <0 0x01da4000 0 0x3000>;
			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
			phys = <&ufs_card_phy>;
			phy-names = "ufsphy";
			lanes-per-direction = <2>;
			#reset-cells = <1>;
			resets = <&gcc GCC_UFS_CARD_BCR>;
			reset-names = "rst";

			power-domains = <&gcc UFS_CARD_GDSC>;

			iommus = <&apps_smmu 0x4a0 0x0>;
			dma-coherent;

			clocks = <&gcc GCC_UFS_CARD_AXI_CLK>,
				 <&gcc GCC_AGGRE_UFS_CARD_AXI_CLK>,
				 <&gcc GCC_UFS_CARD_AHB_CLK>,
				 <&gcc GCC_UFS_CARD_UNIPRO_CORE_CLK>,
				 <&gcc GCC_UFS_REF_CLKREF_CLK>,
				 <&gcc GCC_UFS_CARD_TX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_CARD_RX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_CARD_RX_SYMBOL_1_CLK>;
			clock-names = "core_clk",
				      "bus_aggr_clk",
				      "iface_clk",
				      "core_clk_unipro",
				      "ref_clk",
				      "tx_lane0_sync_clk",
				      "rx_lane0_sync_clk",
				      "rx_lane1_sync_clk";
			freq-table-hz = <75000000 300000000>,
					<0 0>,
					<0 0>,
					<75000000 300000000>,
					<0 0>,
					<0 0>,
					<0 0>,
					<0 0>;
			status = "disabled";
		};

		ufs_card_phy: phy@1da7000 {
			compatible = "qcom,sc8280xp-qmp-ufs-phy";
			reg = <0 0x01da7000 0 0x1000>;

			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_UFS_CARD_PHY_AUX_CLK>,
				 <&gcc GCC_UFS_1_CARD_CLKREF_CLK>;
			clock-names = "ref",
				      "ref_aux",
				      "qref";

			power-domains = <&gcc UFS_CARD_GDSC>;

			resets = <&ufs_card_hc 0>;
			reset-names = "ufsphy";

			#phy-cells = <0>;

			status = "disabled";
		};

		tcsr_mutex: hwlock@1f40000 {
			compatible = "qcom,tcsr-mutex";
			reg = <0x0 0x01f40000 0x0 0x20000>;
			#hwlock-cells = <1>;
		};

		tcsr: syscon@1fc0000 {
			compatible = "qcom,sc8280xp-tcsr", "syscon";
			reg = <0x0 0x01fc0000 0x0 0x30000>;
		};

		gpu: gpu@3d00000 {
			compatible = "qcom,adreno-690.0", "qcom,adreno";

			reg = <0 0x03d00000 0 0x40000>,
			      <0 0x03d9e000 0 0x1000>,
			      <0 0x03d61000 0 0x800>;
			reg-names = "kgsl_3d0_reg_memory",
				    "cx_mem",
				    "cx_dbgc";
			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
			iommus = <&gpu_smmu 0 0xc00>, <&gpu_smmu 1 0xc00>;
			operating-points-v2 = <&gpu_opp_table>;

			qcom,gmu = <&gmu>;
			interconnects = <&gem_noc MASTER_GFX3D 0 &mc_virt SLAVE_EBI1 0>;
			interconnect-names = "gfx-mem";
			#cooling-cells = <2>;

			status = "disabled";

			gpu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-270000000 {
					opp-hz = /bits/ 64 <270000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
					opp-peak-kBps = <451000>;
				};

				opp-410000000 {
					opp-hz = /bits/ 64 <410000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
					opp-peak-kBps = <1555000>;
				};

				opp-500000000 {
					opp-hz = /bits/ 64 <500000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
					opp-peak-kBps = <1555000>;
				};

				opp-547000000 {
					opp-hz = /bits/ 64 <547000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
					opp-peak-kBps = <1555000>;
				};

				opp-606000000 {
					opp-hz = /bits/ 64 <606000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
					opp-peak-kBps = <2736000>;
				};

				opp-640000000 {
					opp-hz = /bits/ 64 <640000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
					opp-peak-kBps = <2736000>;
				};

				opp-655000000 {
					opp-hz = /bits/ 64 <655000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
					opp-peak-kBps = <2736000>;
				};

				opp-690000000 {
					opp-hz = /bits/ 64 <690000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
					opp-peak-kBps = <2736000>;
				};
			};
		};

		gmu: gmu@3d6a000 {
			compatible = "qcom,adreno-gmu-690.0", "qcom,adreno-gmu";
			reg = <0 0x03d6a000 0 0x34000>,
			      <0 0x03de0000 0 0x10000>,
			      <0 0x0b290000 0 0x10000>;
			reg-names = "gmu", "rscc", "gmu_pdc";
			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hfi", "gmu";
			clocks = <&gpucc GPU_CC_CX_GMU_CLK>,
				 <&gpucc GPU_CC_CXO_CLK>,
				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
				 <&gpucc GPU_CC_AHB_CLK>,
				 <&gpucc GPU_CC_HUB_CX_INT_CLK>,
				 <&gpucc GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK>;
			clock-names = "gmu",
				      "cxo",
				      "axi",
				      "memnoc",
				      "ahb",
				      "hub",
				      "smmu_vote";
			power-domains = <&gpucc GPU_CC_CX_GDSC>,
					<&gpucc GPU_CC_GX_GDSC>;
			power-domain-names = "cx",
					     "gx";
			iommus = <&gpu_smmu 5 0xc00>;
			operating-points-v2 = <&gmu_opp_table>;

			gmu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-200000000 {
					opp-hz = /bits/ 64 <200000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
				};

				opp-500000000 {
					opp-hz = /bits/ 64 <500000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
				};
			};
		};

		gpucc: clock-controller@3d90000 {
			compatible = "qcom,sc8280xp-gpucc";
			reg = <0 0x03d90000 0 0x9000>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
			clock-names = "bi_tcxo",
				      "gcc_gpu_gpll0_clk_src",
				      "gcc_gpu_gpll0_div_clk_src";

			power-domains = <&rpmhpd SC8280XP_GFX>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		gpu_smmu: iommu@3da0000 {
			compatible = "qcom,sc8280xp-smmu-500", "qcom,adreno-smmu",
				     "qcom,smmu-500", "arm,mmu-500";
			reg = <0 0x03da0000 0 0x20000>;
			#iommu-cells = <2>;
			#global-interrupts = <2>;
			interrupts = <GIC_SPI 672 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 673 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 678 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 679 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 680 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 686 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 687 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 688 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 689 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
				 <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>,
				 <&gpucc GPU_CC_AHB_CLK>,
				 <&gpucc GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK>,
				 <&gpucc GPU_CC_CX_GMU_CLK>,
				 <&gpucc GPU_CC_HUB_CX_INT_CLK>,
				 <&gpucc GPU_CC_HUB_AON_CLK>;
			clock-names = "gcc_gpu_memnoc_gfx_clk",
				      "gcc_gpu_snoc_dvm_gfx_clk",
				      "gpu_cc_ahb_clk",
				      "gpu_cc_hlos1_vote_gpu_smmu_clk",
				      "gpu_cc_cx_gmu_clk",
				      "gpu_cc_hub_cx_int_clk",
				      "gpu_cc_hub_aon_clk";

			power-domains = <&gpucc GPU_CC_CX_GDSC>;
			dma-coherent;
		};

		usb_0_hsphy: phy@88e5000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x088e5000 0 0x400>;
			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_hsphy0: phy@88e7000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x088e7000 0 0x400>;
			clocks = <&gcc GCC_USB2_HS0_CLKREF_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_HS0_MP_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_hsphy1: phy@88e8000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x088e8000 0 0x400>;
			clocks = <&gcc GCC_USB2_HS1_CLKREF_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_HS1_MP_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_hsphy2: phy@88e9000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x088e9000 0 0x400>;
			clocks = <&gcc GCC_USB2_HS2_CLKREF_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_HS2_MP_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_hsphy3: phy@88ea000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x088ea000 0 0x400>;
			clocks = <&gcc GCC_USB2_HS3_CLKREF_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_HS3_MP_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_qmpphy0: phy@88ef000 {
			compatible = "qcom,sc8280xp-qmp-usb3-uni-phy";
			reg = <0 0x088ef000 0 0x2000>;

			clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>,
				 <&gcc GCC_USB3_MP0_CLKREF_CLK>,
				 <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>;
			clock-names = "aux", "ref", "com_aux", "pipe";

			resets = <&gcc GCC_USB3_UNIPHY_MP0_BCR>,
				 <&gcc GCC_USB3UNIPHY_PHY_MP0_BCR>;
			reset-names = "phy", "phy_phy";

			power-domains = <&gcc USB30_MP_GDSC>;

			#clock-cells = <0>;
			clock-output-names = "usb2_phy0_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_qmpphy1: phy@88f1000 {
			compatible = "qcom,sc8280xp-qmp-usb3-uni-phy";
			reg = <0 0x088f1000 0 0x2000>;

			clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>,
				 <&gcc GCC_USB3_MP1_CLKREF_CLK>,
				 <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_MP_PHY_PIPE_1_CLK>;
			clock-names = "aux", "ref", "com_aux", "pipe";

			resets = <&gcc GCC_USB3_UNIPHY_MP1_BCR>,
				 <&gcc GCC_USB3UNIPHY_PHY_MP1_BCR>;
			reset-names = "phy", "phy_phy";

			power-domains = <&gcc USB30_MP_GDSC>;

			#clock-cells = <0>;
			clock-output-names = "usb2_phy1_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		remoteproc_adsp: remoteproc@3000000 {
			compatible = "qcom,sc8280xp-adsp-pas";
			reg = <0 0x03000000 0 0x100>;

			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 7 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack", "shutdown-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SC8280XP_LCX>,
					<&rpmhpd SC8280XP_LMX>;
			power-domain-names = "lcx", "lmx";

			memory-region = <&pil_adsp_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_adsp_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			remoteproc_adsp_glink: glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_LPASS
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "lpass";
				qcom,remote-pid = <2>;

				gpr {
					compatible = "qcom,gpr";
					qcom,glink-channels = "adsp_apps";
					qcom,domain = <GPR_DOMAIN_ID_ADSP>;
					qcom,intents = <512 20>;
					#address-cells = <1>;
					#size-cells = <0>;

					q6apm: service@1 {
						compatible = "qcom,q6apm";
						reg = <GPR_APM_MODULE_IID>;
						#sound-dai-cells = <0>;
						qcom,protection-domain = "avs/audio",
									 "msm/adsp/audio_pd";
						q6apmdai: dais {
							compatible = "qcom,q6apm-dais";
							iommus = <&apps_smmu 0x0c01 0x0>;
						};

						q6apmbedai: bedais {
							compatible = "qcom,q6apm-lpass-dais";
							#sound-dai-cells = <1>;
						};
					};

					q6prm: service@2 {
						compatible = "qcom,q6prm";
						reg = <GPR_PRM_MODULE_IID>;
						qcom,protection-domain = "avs/audio",
									 "msm/adsp/audio_pd";
						q6prmcc: clock-controller {
							compatible = "qcom,q6prm-lpass-clocks";
							#clock-cells = <2>;
						};
					};
				};
			};
		};

		rxmacro: rxmacro@3200000 {
			compatible = "qcom,sc8280xp-lpass-rx-macro";
			reg = <0 0x03200000 0 0x1000>;
			clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&vamacro>;
			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
			assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
					  <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			assigned-clock-rates = <19200000>, <19200000>;

			clock-output-names = "mclk";
			#clock-cells = <0>;
			#sound-dai-cells = <1>;

			pinctrl-names = "default";
			pinctrl-0 = <&rx_swr_default>;

			status = "disabled";
		};

		swr1: soundwire@3210000 {
			compatible = "qcom,soundwire-v1.6.0";
			reg = <0 0x03210000 0 0x2000>;
			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&rxmacro>;
			clock-names = "iface";
			resets = <&lpass_audiocc LPASS_AUDIO_SWR_RX_CGCR>;
			reset-names = "swr_audio_cgcr";
			label = "RX";

			qcom,din-ports = <0>;
			qcom,dout-ports = <5>;

			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x1f 0x1f 0x07 0x00>;
			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0B 0x01 0x00>;
			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0B 0x00 0x00>;
			qcom,ports-hstart =		/bits/ 8 <0xff 0x03 0x00 0xff 0xff>;
			qcom,ports-hstop =		/bits/ 8 <0xff 0x06 0x0f 0xff 0xff>;
			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xff 0xff>;
			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0xff 0x01 0xff 0xff>;
			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff>;

			#sound-dai-cells = <1>;
			#address-cells = <2>;
			#size-cells = <0>;

			status = "disabled";
		};

		txmacro: txmacro@3220000 {
			compatible = "qcom,sc8280xp-lpass-tx-macro";
			reg = <0 0x03220000 0 0x1000>;
			pinctrl-names = "default";
			pinctrl-0 = <&tx_swr_default>;
			clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&vamacro>;

			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
			assigned-clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
					  <&q6prmcc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			assigned-clock-rates = <19200000>, <19200000>;
			clock-output-names = "mclk";

			#clock-cells = <0>;
			#sound-dai-cells = <1>;

			status = "disabled";
		};

		wsamacro: codec@3240000 {
			compatible = "qcom,sc8280xp-lpass-wsa-macro";
			reg = <0 0x03240000 0 0x1000>;
			clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&vamacro>;
			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
			assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
					  <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			assigned-clock-rates = <19200000>, <19200000>;

			#clock-cells = <0>;
			clock-output-names = "mclk";
			#sound-dai-cells = <1>;

			pinctrl-names = "default";
			pinctrl-0 = <&wsa_swr_default>;

			status = "disabled";
		};

		swr0: soundwire@3250000 {
			reg = <0 0x03250000 0 0x2000>;
			compatible = "qcom,soundwire-v1.6.0";
			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&wsamacro>;
			clock-names = "iface";
			resets = <&lpass_audiocc LPASS_AUDIO_SWR_WSA_CGCR>;
			reset-names = "swr_audio_cgcr";
			label = "WSA";

			qcom,din-ports = <2>;
			qcom,dout-ports = <6>;

			qcom,ports-sinterval-low =	/bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
			qcom,ports-offset1 =		/bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
			qcom,ports-offset2 =		/bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
			qcom,ports-hstart =		/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-hstop =		/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-word-length =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0xff 0x01 0xff 0xff 0x01 0xff 0xff>;
			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
			qcom,ports-lane-control =	/bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;

			#sound-dai-cells = <1>;
			#address-cells = <2>;
			#size-cells = <0>;

			status = "disabled";
		};

		lpass_audiocc: clock-controller@32a9000 {
			compatible = "qcom,sc8280xp-lpassaudiocc";
			reg = <0 0x032a9000 0 0x1000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		swr2: soundwire@3330000 {
			compatible = "qcom,soundwire-v1.6.0";
			reg = <0 0x03330000 0 0x2000>;
			interrupts = <GIC_SPI 959 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "core", "wakeup";

			clocks = <&txmacro>;
			clock-names = "iface";
			resets = <&lpasscc LPASS_AUDIO_SWR_TX_CGCR>;
			reset-names = "swr_audio_cgcr";
			label = "TX";
			#sound-dai-cells = <1>;
			#address-cells = <2>;
			#size-cells = <0>;

			qcom,din-ports = <4>;
			qcom,dout-ports = <0>;
			qcom,ports-sinterval-low =	/bits/ 8 <0x01 0x01 0x03 0x03>;
			qcom,ports-offset1 =		/bits/ 8 <0x01 0x00 0x02 0x00>;
			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x00 0x00>;
			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0xff 0xff 0xff>;
			qcom,ports-hstart =		/bits/ 8 <0xff 0xff 0xff 0xff>;
			qcom,ports-hstop =		/bits/ 8 <0xff 0xff 0xff 0xff>;
			qcom,ports-word-length =	/bits/ 8 <0xff 0xff 0xff 0xff>;
			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff>;
			qcom,ports-lane-control =	/bits/ 8 <0x00 0x01 0x00 0x01>;

			status = "disabled";
		};

		vamacro: codec@3370000 {
			compatible = "qcom,sc8280xp-lpass-va-macro";
			reg = <0 0x03370000 0 0x1000>;
			clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			clock-names = "mclk", "macro", "dcodec", "npl";
			assigned-clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			assigned-clock-rates = <19200000>;

			#clock-cells = <0>;
			clock-output-names = "fsgen";
			#sound-dai-cells = <1>;

			status = "disabled";
		};

		lpass_tlmm: pinctrl@33c0000 {
			compatible = "qcom,sc8280xp-lpass-lpi-pinctrl";
			reg = <0 0x33c0000 0x0 0x20000>,
			      <0 0x3550000 0x0 0x10000>;
			gpio-controller;
			#gpio-cells = <2>;
			gpio-ranges = <&lpass_tlmm 0 0 19>;

			clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			clock-names = "core", "audio";

			status = "disabled";

			tx_swr_default: tx-swr-default-state {
				clk-pins {
					pins = "gpio0";
					function = "swr_tx_clk";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-disable;
				};

				data-pins {
					pins = "gpio1", "gpio2";
					function = "swr_tx_data";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-bus-hold;
				};
			};

			rx_swr_default: rx-swr-default-state {
				clk-pins {
					pins = "gpio3";
					function = "swr_rx_clk";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-disable;
				};

				data-pins {
					pins = "gpio4", "gpio5";
					function = "swr_rx_data";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-bus-hold;
				};
			};

			dmic01_default: dmic01-default-state {
				clk-pins {
					pins = "gpio6";
					function = "dmic1_clk";
					drive-strength = <8>;
					output-high;
				};

				data-pins {
					pins = "gpio7";
					function = "dmic1_data";
					drive-strength = <8>;
					input-enable;
				};
			};

			dmic01_sleep: dmic01-sleep-state {
				clk-pins {
					pins = "gpio6";
					function = "dmic1_clk";
					drive-strength = <2>;
					bias-disable;
					output-low;
				};

				data-pins {
					pins = "gpio7";
					function = "dmic1_data";
					drive-strength = <2>;
					bias-pull-down;
					input-enable;
				};
			};

			dmic23_default: dmic23-default-state {
				clk-pins {
					pins = "gpio8";
					function = "dmic2_clk";
					drive-strength = <8>;
					output-high;
				};

				data-pins {
					pins = "gpio9";
					function = "dmic2_data";
					drive-strength = <8>;
					input-enable;
				};
			};

			dmic23_sleep: dmic23-sleep-state {
				clk-pins {
					pins = "gpio8";
					function = "dmic2_clk";
					drive-strength = <2>;
					bias-disable;
					output-low;
				};

				data-pins {
					pins = "gpio9";
					function = "dmic2_data";
					drive-strength = <2>;
					bias-pull-down;
					input-enable;
				};
			};

			wsa_swr_default: wsa-swr-default-state {
				clk-pins {
					pins = "gpio10";
					function = "wsa_swr_clk";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-disable;
				};

				data-pins {
					pins = "gpio11";
					function = "wsa_swr_data";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-bus-hold;
				};
			};

			wsa2_swr_default: wsa2-swr-default-state {
				clk-pins {
					pins = "gpio15";
					function = "wsa2_swr_clk";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-disable;
				};

				data-pins {
					pins = "gpio16";
					function = "wsa2_swr_data";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-bus-hold;
				};
			};
		};

		lpasscc: clock-controller@33e0000 {
			compatible = "qcom,sc8280xp-lpasscc";
			reg = <0 0x033e0000 0 0x12000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		sdc2: mmc@8804000 {
			compatible = "qcom,sc8280xp-sdhci", "qcom,sdhci-msm-v5";
			reg = <0 0x08804000 0 0x1000>;

			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hc_irq", "pwr_irq";

			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
				 <&gcc GCC_SDCC2_APPS_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "iface", "core", "xo";
			resets = <&gcc GCC_SDCC2_BCR>;
			interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>;
			interconnect-names = "sdhc-ddr","cpu-sdhc";
			iommus = <&apps_smmu 0x4e0 0x0>;
			power-domains = <&rpmhpd SC8280XP_CX>;
			operating-points-v2 = <&sdc2_opp_table>;
			bus-width = <4>;
			dma-coherent;

			status = "disabled";

			sdc2_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-100000000 {
					opp-hz = /bits/ 64 <100000000>;
					required-opps = <&rpmhpd_opp_low_svs>;
					opp-peak-kBps = <1800000 400000>;
					opp-avg-kBps = <100000 0>;
				};

				opp-202000000 {
					opp-hz = /bits/ 64 <202000000>;
					required-opps = <&rpmhpd_opp_svs_l1>;
					opp-peak-kBps = <5400000 1600000>;
					opp-avg-kBps = <200000 0>;
				};
			};
		};

		usb_0_qmpphy: phy@88eb000 {
			compatible = "qcom,sc8280xp-qmp-usb43dp-phy";
			reg = <0 0x088eb000 0 0x4000>;

			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
				 <&gcc GCC_USB4_EUD_CLKREF_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
			clock-names = "aux", "ref", "com_aux", "usb3_pipe";

			power-domains = <&gcc USB30_PRIM_GDSC>;

			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
				 <&gcc GCC_USB4_DP_PHY_PRIM_BCR>;
			reset-names = "phy", "common";

			#clock-cells = <1>;
			#phy-cells = <1>;

			status = "disabled";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;

					usb_0_qmpphy_out: endpoint {};
				};

				port@1 {
					reg = <1>;

					usb_0_qmpphy_usb_ss_in: endpoint {
						remote-endpoint = <&usb_0_dwc3_ss>;
					};
				};

				port@2 {
					reg = <2>;

					usb_0_qmpphy_dp_in: endpoint {};
				};
			};
		};

		usb_1_hsphy: phy@8902000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x08902000 0 0x400>;
			#phy-cells = <0>;

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "ref";

			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;

			status = "disabled";
		};

		usb_1_qmpphy: phy@8903000 {
			compatible = "qcom,sc8280xp-qmp-usb43dp-phy";
			reg = <0 0x08903000 0 0x4000>;

			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
				 <&gcc GCC_USB4_CLKREF_CLK>,
				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
			clock-names = "aux", "ref", "com_aux", "usb3_pipe";

			power-domains = <&gcc USB30_SEC_GDSC>;

			resets = <&gcc GCC_USB3_PHY_SEC_BCR>,
				 <&gcc GCC_USB4_1_DP_PHY_PRIM_BCR>;
			reset-names = "phy", "common";

			#clock-cells = <1>;
			#phy-cells = <1>;

			status = "disabled";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;

					usb_1_qmpphy_out: endpoint {};
				};

				port@1 {
					reg = <1>;

					usb_1_qmpphy_usb_ss_in: endpoint {
						remote-endpoint = <&usb_1_dwc3_ss>;
					};
				};

				port@2 {
					reg = <2>;

					usb_1_qmpphy_dp_in: endpoint {};
				};
			};
		};

		mdss1_dp0_phy: phy@8909a00 {
			compatible = "qcom,sc8280xp-dp-phy";
			reg = <0 0x08909a00 0 0x19c>,
			      <0 0x08909200 0 0xec>,
			      <0 0x08909600 0 0xec>,
			      <0 0x08909000 0 0x1c8>;

			clocks = <&dispcc1 DISP_CC_MDSS_DPTX0_AUX_CLK>,
				 <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
			clock-names = "aux", "cfg_ahb";
			power-domains = <&rpmhpd SC8280XP_MX>;

			#clock-cells = <1>;
			#phy-cells = <0>;

			status = "disabled";
		};

		mdss1_dp1_phy: phy@890ca00 {
			compatible = "qcom,sc8280xp-dp-phy";
			reg = <0 0x0890ca00 0 0x19c>,
			      <0 0x0890c200 0 0xec>,
			      <0 0x0890c600 0 0xec>,
			      <0 0x0890c000 0 0x1c8>;

			clocks = <&dispcc1 DISP_CC_MDSS_DPTX1_AUX_CLK>,
				 <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
			clock-names = "aux", "cfg_ahb";
			power-domains = <&rpmhpd SC8280XP_MX>;

			#clock-cells = <1>;
			#phy-cells = <0>;

			status = "disabled";
		};

		pmu@9091000 {
			compatible = "qcom,sc8280xp-llcc-bwmon", "qcom,sc7280-llcc-bwmon";
			reg = <0 0x09091000 0 0x1000>;

			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;

			interconnects = <&mc_virt MASTER_LLCC 3 &mc_virt SLAVE_EBI1 3>;

			operating-points-v2 = <&llcc_bwmon_opp_table>;

			llcc_bwmon_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-0 {
					opp-peak-kBps = <762000>;
				};
				opp-1 {
					opp-peak-kBps = <1720000>;
				};
				opp-2 {
					opp-peak-kBps = <2086000>;
				};
				opp-3 {
					opp-peak-kBps = <2597000>;
				};
				opp-4 {
					opp-peak-kBps = <2929000>;
				};
				opp-5 {
					opp-peak-kBps = <3879000>;
				};
				opp-6 {
					opp-peak-kBps = <5161000>;
				};
				opp-7 {
					opp-peak-kBps = <5931000>;
				};
				opp-8 {
					opp-peak-kBps = <6515000>;
				};
				opp-9 {
					opp-peak-kBps = <7980000>;
				};
				opp-10 {
					opp-peak-kBps = <8136000>;
				};
				opp-11 {
					opp-peak-kBps = <10437000>;
				};
				opp-12 {
					opp-peak-kBps = <12191000>;
				};
			};
		};

		pmu@90b6400 {
			compatible = "qcom,sc8280xp-cpu-bwmon", "qcom,sdm845-bwmon";
			reg = <0 0x090b6400 0 0x600>;

			interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>;

			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &gem_noc SLAVE_LLCC 3>;
			operating-points-v2 = <&cpu_bwmon_opp_table>;

			cpu_bwmon_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-0 {
					opp-peak-kBps = <2288000>;
				};
				opp-1 {
					opp-peak-kBps = <4577000>;
				};
				opp-2 {
					opp-peak-kBps = <7110000>;
				};
				opp-3 {
					opp-peak-kBps = <9155000>;
				};
				opp-4 {
					opp-peak-kBps = <12298000>;
				};
				opp-5 {
					opp-peak-kBps = <14236000>;
				};
				opp-6 {
					opp-peak-kBps = <15258001>;
				};
			};
		};

		system-cache-controller@9200000 {
			compatible = "qcom,sc8280xp-llcc";
			reg = <0 0x09200000 0 0x58000>, <0 0x09280000 0 0x58000>,
			      <0 0x09300000 0 0x58000>, <0 0x09380000 0 0x58000>,
			      <0 0x09400000 0 0x58000>, <0 0x09480000 0 0x58000>,
			      <0 0x09500000 0 0x58000>, <0 0x09580000 0 0x58000>,
			      <0 0x09600000 0 0x58000>;
			reg-names = "llcc0_base", "llcc1_base", "llcc2_base",
				    "llcc3_base", "llcc4_base", "llcc5_base",
				    "llcc6_base", "llcc7_base",  "llcc_broadcast_base";
			interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
		};

		usb_2: usb@a4f8800 {
			compatible = "qcom,sc8280xp-dwc3-mp", "qcom,dwc3";
			reg = <0 0x0a4f8800 0 0x400>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_MP_AXI_CLK>,
				 <&gcc GCC_USB30_MP_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_MP_AXI_CLK>,
				 <&gcc GCC_USB30_MP_SLEEP_CLK>,
				 <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_NORTH_AXI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_SOUTH_AXI_CLK>,
				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";

			assigned-clocks = <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_MP_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			interrupts-extended = <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
					      <&intc GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
					      <&intc GIC_SPI 857 IRQ_TYPE_LEVEL_HIGH>,
					      <&intc GIC_SPI 856 IRQ_TYPE_LEVEL_HIGH>,
					      <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
					      <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
					      <&intc GIC_SPI 860 IRQ_TYPE_LEVEL_HIGH>,
					      <&intc GIC_SPI 859 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 127 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 126 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 129 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 128 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 131 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 130 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 133 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 132 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 16 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;

			interrupt-names = "pwr_event_1", "pwr_event_2",
					  "pwr_event_3", "pwr_event_4",
					  "hs_phy_1",	 "hs_phy_2",
					  "hs_phy_3",	 "hs_phy_4",
					  "dp_hs_phy_1", "dm_hs_phy_1",
					  "dp_hs_phy_2", "dm_hs_phy_2",
					  "dp_hs_phy_3", "dm_hs_phy_3",
					  "dp_hs_phy_4", "dm_hs_phy_4",
					  "ss_phy_1",	 "ss_phy_2";

			power-domains = <&gcc USB30_MP_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			resets = <&gcc GCC_USB30_MP_BCR>;

			interconnects = <&aggre1_noc MASTER_USB3_MP 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_MP 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			wakeup-source;

			status = "disabled";

			usb_2_dwc3: usb@a400000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a400000 0 0xcd00>;
				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x800 0x0>;
				phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>,
				       <&usb_2_hsphy1>, <&usb_2_qmpphy1>,
				       <&usb_2_hsphy2>,
				       <&usb_2_hsphy3>;
				phy-names = "usb2-0", "usb3-0",
					    "usb2-1", "usb3-1",
					    "usb2-2",
					    "usb2-3";
				dr_mode = "host";
			};
		};

		usb_0: usb@a6f8800 {
			compatible = "qcom,sc8280xp-dwc3", "qcom,dwc3";
			reg = <0 0x0a6f8800 0 0x400>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_NORTH_AXI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_SOUTH_AXI_CLK>,
				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";

			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			interrupts-extended = <&intc GIC_SPI 804 IRQ_TYPE_LEVEL_HIGH>,
					      <&intc GIC_SPI 805 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 138 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "pwr_event",
					  "hs_phy_irq",
					  "dp_hs_phy_irq",
					  "dm_hs_phy_irq",
					  "ss_phy_irq";

			power-domains = <&gcc USB30_PRIM_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			resets = <&gcc GCC_USB30_PRIM_BCR>;

			interconnects = <&aggre1_noc MASTER_USB3_0 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_0 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			wakeup-source;

			status = "disabled";

			usb_0_dwc3: usb@a600000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a600000 0 0xcd00>;
				interrupts = <GIC_SPI 803 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x820 0x0>;
				phys = <&usb_0_hsphy>, <&usb_0_qmpphy QMP_USB43DP_USB3_PHY>;
				phy-names = "usb2-phy", "usb3-phy";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;

						usb_0_dwc3_hs: endpoint {
						};
					};

					port@1 {
						reg = <1>;

						usb_0_dwc3_ss: endpoint {
							remote-endpoint = <&usb_0_qmpphy_usb_ss_in>;
						};
					};
				};
			};
		};

		usb_1: usb@a8f8800 {
			compatible = "qcom,sc8280xp-dwc3", "qcom,dwc3";
			reg = <0 0x0a8f8800 0 0x400>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_NORTH_AXI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_SOUTH_AXI_CLK>,
				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";

			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			interrupts-extended = <&intc GIC_SPI 811 IRQ_TYPE_LEVEL_HIGH>,
					      <&intc GIC_SPI 790 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 12 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 13 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 136 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "pwr_event",
					  "hs_phy_irq",
					  "dp_hs_phy_irq",
					  "dm_hs_phy_irq",
					  "ss_phy_irq";

			power-domains = <&gcc USB30_SEC_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			resets = <&gcc GCC_USB30_SEC_BCR>;

			interconnects = <&aggre1_noc MASTER_USB3_1 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_1 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			wakeup-source;

			status = "disabled";

			usb_1_dwc3: usb@a800000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a800000 0 0xcd00>;
				interrupts = <GIC_SPI 810 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x860 0x0>;
				phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
				phy-names = "usb2-phy", "usb3-phy";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;

						usb_1_dwc3_hs: endpoint {
						};
					};

					port@1 {
						reg = <1>;

						usb_1_dwc3_ss: endpoint {
							remote-endpoint = <&usb_1_qmpphy_usb_ss_in>;
						};
					};
				};
			};
		};

		cci0: cci@ac4a000 {
			compatible = "qcom,sc8280xp-cci", "qcom,msm8996-cci";
			reg = <0 0x0ac4a000 0 0x1000>;

			interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;

			clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
				 <&camcc CAMCC_SLOW_AHB_CLK_SRC>,
				 <&camcc CAMCC_CPAS_AHB_CLK>,
				 <&camcc CAMCC_CCI_0_CLK>;
			clock-names = "camnoc_axi",
				      "slow_ahb_src",
				      "cpas_ahb",
				      "cci";

			power-domains = <&camcc TITAN_TOP_GDSC>;

			pinctrl-0 = <&cci0_default>;
			pinctrl-1 = <&cci0_sleep>;
			pinctrl-names = "default", "sleep";

			#address-cells = <1>;
			#size-cells = <0>;

			status = "disabled";

			cci0_i2c0: i2c-bus@0 {
				reg = <0>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};

			cci0_i2c1: i2c-bus@1 {
				reg = <1>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		cci1: cci@ac4b000 {
			compatible = "qcom,sc8280xp-cci", "qcom,msm8996-cci";
			reg = <0 0x0ac4b000 0 0x1000>;

			interrupts = <GIC_SPI 271 IRQ_TYPE_EDGE_RISING>;

			clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
				 <&camcc CAMCC_SLOW_AHB_CLK_SRC>,
				 <&camcc CAMCC_CPAS_AHB_CLK>,
				 <&camcc CAMCC_CCI_1_CLK>;
			clock-names = "camnoc_axi",
				      "slow_ahb_src",
				      "cpas_ahb",
				      "cci";

			power-domains = <&camcc TITAN_TOP_GDSC>;

			pinctrl-0 = <&cci1_default>;
			pinctrl-1 = <&cci1_sleep>;
			pinctrl-names = "default", "sleep";

			#address-cells = <1>;
			#size-cells = <0>;

			status = "disabled";

			cci1_i2c0: i2c-bus@0 {
				reg = <0>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};

			cci1_i2c1: i2c-bus@1 {
				reg = <1>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		cci2: cci@ac4c000 {
			compatible = "qcom,sc8280xp-cci", "qcom,msm8996-cci";
			reg = <0 0x0ac4c000 0 0x1000>;

			interrupts = <GIC_SPI 651 IRQ_TYPE_EDGE_RISING>;

			clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
				 <&camcc CAMCC_SLOW_AHB_CLK_SRC>,
				 <&camcc CAMCC_CPAS_AHB_CLK>,
				 <&camcc CAMCC_CCI_2_CLK>;
			clock-names = "camnoc_axi",
				      "slow_ahb_src",
				      "cpas_ahb",
				      "cci";
			power-domains = <&camcc TITAN_TOP_GDSC>;

			pinctrl-0 = <&cci2_default>;
			pinctrl-1 = <&cci2_sleep>;
			pinctrl-names = "default", "sleep";

			#address-cells = <1>;
			#size-cells = <0>;

			status = "disabled";

			cci2_i2c0: i2c-bus@0 {
				reg = <0>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};

			cci2_i2c1: i2c-bus@1 {
				reg = <1>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		cci3: cci@ac4d000 {
			compatible = "qcom,sc8280xp-cci", "qcom,msm8996-cci";
			reg = <0 0x0ac4d000 0 0x1000>;

			interrupts = <GIC_SPI 650 IRQ_TYPE_EDGE_RISING>;

			clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
				 <&camcc CAMCC_SLOW_AHB_CLK_SRC>,
				 <&camcc CAMCC_CPAS_AHB_CLK>,
				 <&camcc CAMCC_CCI_3_CLK>;
			clock-names = "camnoc_axi",
				      "slow_ahb_src",
				      "cpas_ahb",
				      "cci";

			power-domains = <&camcc TITAN_TOP_GDSC>;

			pinctrl-0 = <&cci3_default>;
			pinctrl-1 = <&cci3_sleep>;
			pinctrl-names = "default", "sleep";

			#address-cells = <1>;
			#size-cells = <0>;

			status = "disabled";

			cci3_i2c0: i2c-bus@0 {
				reg = <0>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};

			cci3_i2c1: i2c-bus@1 {
				reg = <1>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		camss: camss@ac5a000 {
			compatible = "qcom,sc8280xp-camss";

			reg = <0 0x0ac5a000 0 0x2000>,
			      <0 0x0ac5c000 0 0x2000>,
			      <0 0x0ac65000 0 0x2000>,
			      <0 0x0ac67000 0 0x2000>,
			      <0 0x0acaf000 0 0x4000>,
			      <0 0x0acb3000 0 0x1000>,
			      <0 0x0acb6000 0 0x4000>,
			      <0 0x0acba000 0 0x1000>,
			      <0 0x0acbd000 0 0x4000>,
			      <0 0x0acc1000 0 0x1000>,
			      <0 0x0acc4000 0 0x4000>,
			      <0 0x0acc8000 0 0x1000>,
			      <0 0x0accb000 0 0x4000>,
			      <0 0x0accf000 0 0x1000>,
			      <0 0x0acd2000 0 0x4000>,
			      <0 0x0acd6000 0 0x1000>,
			      <0 0x0acd9000 0 0x4000>,
			      <0 0x0acdd000 0 0x1000>,
			      <0 0x0ace0000 0 0x4000>,
			      <0 0x0ace4000 0 0x1000>;
			reg-names = "csiphy2",
				    "csiphy3",
				    "csiphy0",
				    "csiphy1",
				    "vfe0",
				    "csid0",
				    "vfe1",
				    "csid1",
				    "vfe2",
				    "csid2",
				    "vfe_lite0",
				    "csid0_lite",
				    "vfe_lite1",
				    "csid1_lite",
				    "vfe_lite2",
				    "csid2_lite",
				    "vfe_lite3",
				    "csid3_lite",
				    "vfe3",
				    "csid3";

			interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 640 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 758 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 759 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 760 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 761 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 762 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 764 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "csid1_lite",
					  "vfe_lite1",
					  "csiphy3",
					  "csid0",
					  "vfe0",
					  "csid1",
					  "vfe1",
					  "csid0_lite",
					  "vfe_lite0",
					  "csiphy0",
					  "csiphy1",
					  "csiphy2",
					  "csid2",
					  "vfe2",
					  "csid3_lite",
					  "csid2_lite",
					  "vfe_lite3",
					  "vfe_lite2",
					  "csid3",
					  "vfe3";

			power-domains = <&camcc IFE_0_GDSC>,
					<&camcc IFE_1_GDSC>,
					<&camcc IFE_2_GDSC>,
					<&camcc IFE_3_GDSC>,
					<&camcc TITAN_TOP_GDSC>;
			power-domain-names = "ife0",
					     "ife1",
					     "ife2",
					     "ife3",
					     "top";

			clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
				 <&camcc CAMCC_CPAS_AHB_CLK>,
				 <&camcc CAMCC_CSIPHY0_CLK>,
				 <&camcc CAMCC_CSI0PHYTIMER_CLK>,
				 <&camcc CAMCC_CSIPHY1_CLK>,
				 <&camcc CAMCC_CSI1PHYTIMER_CLK>,
				 <&camcc CAMCC_CSIPHY2_CLK>,
				 <&camcc CAMCC_CSI2PHYTIMER_CLK>,
				 <&camcc CAMCC_CSIPHY3_CLK>,
				 <&camcc CAMCC_CSI3PHYTIMER_CLK>,
				 <&camcc CAMCC_IFE_0_AXI_CLK>,
				 <&camcc CAMCC_IFE_0_CLK>,
				 <&camcc CAMCC_IFE_0_CPHY_RX_CLK>,
				 <&camcc CAMCC_IFE_0_CSID_CLK>,
				 <&camcc CAMCC_IFE_1_AXI_CLK>,
				 <&camcc CAMCC_IFE_1_CLK>,
				 <&camcc CAMCC_IFE_1_CPHY_RX_CLK>,
				 <&camcc CAMCC_IFE_1_CSID_CLK>,
				 <&camcc CAMCC_IFE_2_AXI_CLK>,
				 <&camcc CAMCC_IFE_2_CLK>,
				 <&camcc CAMCC_IFE_2_CPHY_RX_CLK>,
				 <&camcc CAMCC_IFE_2_CSID_CLK>,
				 <&camcc CAMCC_IFE_3_AXI_CLK>,
				 <&camcc CAMCC_IFE_3_CLK>,
				 <&camcc CAMCC_IFE_3_CPHY_RX_CLK>,
				 <&camcc CAMCC_IFE_3_CSID_CLK>,
				 <&camcc CAMCC_IFE_LITE_0_CLK>,
				 <&camcc CAMCC_IFE_LITE_0_CPHY_RX_CLK>,
				 <&camcc CAMCC_IFE_LITE_0_CSID_CLK>,
				 <&camcc CAMCC_IFE_LITE_1_CLK>,
				 <&camcc CAMCC_IFE_LITE_1_CPHY_RX_CLK>,
				 <&camcc CAMCC_IFE_LITE_1_CSID_CLK>,
				 <&camcc CAMCC_IFE_LITE_2_CLK>,
				 <&camcc CAMCC_IFE_LITE_2_CPHY_RX_CLK>,
				 <&camcc CAMCC_IFE_LITE_2_CSID_CLK>,
				 <&camcc CAMCC_IFE_LITE_3_CLK>,
				 <&camcc CAMCC_IFE_LITE_3_CPHY_RX_CLK>,
				 <&camcc CAMCC_IFE_LITE_3_CSID_CLK>,
				 <&gcc GCC_CAMERA_HF_AXI_CLK>,
				 <&gcc GCC_CAMERA_SF_AXI_CLK>;
			clock-names = "camnoc_axi",
				      "cpas_ahb",
				      "csiphy0",
				      "csiphy0_timer",
				      "csiphy1",
				      "csiphy1_timer",
				      "csiphy2",
				      "csiphy2_timer",
				      "csiphy3",
				      "csiphy3_timer",
				      "vfe0_axi",
				      "vfe0",
				      "vfe0_cphy_rx",
				      "vfe0_csid",
				      "vfe1_axi",
				      "vfe1",
				      "vfe1_cphy_rx",
				      "vfe1_csid",
				      "vfe2_axi",
				      "vfe2",
				      "vfe2_cphy_rx",
				      "vfe2_csid",
				      "vfe3_axi",
				      "vfe3",
				      "vfe3_cphy_rx",
				      "vfe3_csid",
				      "vfe_lite0",
				      "vfe_lite0_cphy_rx",
				      "vfe_lite0_csid",
				      "vfe_lite1",
				      "vfe_lite1_cphy_rx",
				      "vfe_lite1_csid",
				      "vfe_lite2",
				      "vfe_lite2_cphy_rx",
				      "vfe_lite2_csid",
				      "vfe_lite3",
				      "vfe_lite3_cphy_rx",
				      "vfe_lite3_csid",
				      "gcc_axi_hf",
				      "gcc_axi_sf";

			iommus = <&apps_smmu 0x2000 0x4e0>,
				 <&apps_smmu 0x2020 0x4e0>,
				 <&apps_smmu 0x2040 0x4e0>,
				 <&apps_smmu 0x2060 0x4e0>,
				 <&apps_smmu 0x2080 0x4e0>,
				 <&apps_smmu 0x20e0 0x4e0>,
				 <&apps_smmu 0x20c0 0x4e0>,
				 <&apps_smmu 0x20a0 0x4e0>,
				 <&apps_smmu 0x2400 0x4e0>,
				 <&apps_smmu 0x2420 0x4e0>,
				 <&apps_smmu 0x2440 0x4e0>,
				 <&apps_smmu 0x2460 0x4e0>,
				 <&apps_smmu 0x2480 0x4e0>,
				 <&apps_smmu 0x24e0 0x4e0>,
				 <&apps_smmu 0x24c0 0x4e0>,
				 <&apps_smmu 0x24a0 0x4e0>;

			interconnects = <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_CAMERA_CFG 0>,
					<&mmss_noc MASTER_CAMNOC_HF 0 &mc_virt SLAVE_EBI1 0>,
					<&mmss_noc MASTER_CAMNOC_SF 0 &mc_virt SLAVE_EBI1 0>,
					<&mmss_noc MASTER_CAMNOC_ICP 0 &mc_virt SLAVE_EBI1 0>;
			interconnect-names = "cam_ahb",
					     "cam_hf_mnoc",
					     "cam_sf_mnoc",
					     "cam_sf_icp_mnoc";

			status = "disabled";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					#address-cells = <1>;
					#size-cells = <0>;
				};

				port@1 {
					reg = <1>;
					#address-cells = <1>;
					#size-cells = <0>;
				};

				port@2 {
					reg = <2>;
					#address-cells = <1>;
					#size-cells = <0>;
				};

				port@3 {
					reg = <3>;
					#address-cells = <1>;
					#size-cells = <0>;
				};
			};
		};

		camcc: clock-controller@ad00000 {
			compatible = "qcom,sc8280xp-camcc";
			reg = <0 0x0ad00000 0 0x20000>;
			clocks = <&gcc GCC_CAMERA_AHB_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&rpmhcc RPMH_CXO_CLK_A>,
				 <&sleep_clk>;
			power-domains = <&rpmhpd SC8280XP_MMCX>;
			required-opps = <&rpmhpd_opp_low_svs>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		mdss0: display-subsystem@ae00000 {
			compatible = "qcom,sc8280xp-mdss";
			reg = <0 0x0ae00000 0 0x1000>;
			reg-names = "mdss";

			clocks = <&gcc GCC_DISP_AHB_CLK>,
				 <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
				 <&dispcc0 DISP_CC_MDSS_MDP_CLK>;
			clock-names = "iface",
				      "ahb",
				      "core";
			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
			interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
					<&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
			interconnect-names = "mdp0-mem", "mdp1-mem";
			iommus = <&apps_smmu 0x1000 0x402>;
			power-domains = <&dispcc0 MDSS_GDSC>;
			resets = <&dispcc0 DISP_CC_MDSS_CORE_BCR>;

			interrupt-controller;
			#interrupt-cells = <1>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";

			mdss0_mdp: display-controller@ae01000 {
				compatible = "qcom,sc8280xp-dpu";
				reg = <0 0x0ae01000 0 0x8f000>,
				      <0 0x0aeb0000 0 0x2008>;
				reg-names = "mdp", "vbif";

				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
					 <&gcc GCC_DISP_SF_AXI_CLK>,
					 <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc0 DISP_CC_MDSS_MDP_LUT_CLK>,
					 <&dispcc0 DISP_CC_MDSS_MDP_CLK>,
					 <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>;
				clock-names = "bus",
					      "nrt_bus",
					      "iface",
					      "lut",
					      "core",
					      "vsync";
				interrupt-parent = <&mdss0>;
				interrupts = <0>;
				power-domains = <&rpmhpd SC8280XP_MMCX>;

				assigned-clocks = <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>;
				assigned-clock-rates = <19200000>;
				operating-points-v2 = <&mdss0_mdp_opp_table>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss0_intf0_out: endpoint {
							remote-endpoint = <&mdss0_dp0_in>;
						};
					};

					port@4 {
						reg = <4>;
						mdss0_intf4_out: endpoint {
							remote-endpoint = <&mdss0_dp1_in>;
						};
					};

					port@5 {
						reg = <5>;
						mdss0_intf5_out: endpoint {
							remote-endpoint = <&mdss0_dp3_in>;
						};
					};

					port@6 {
						reg = <6>;
						mdss0_intf6_out: endpoint {
							remote-endpoint = <&mdss0_dp2_in>;
						};
					};
				};

				mdss0_mdp_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-200000000 {
						opp-hz = /bits/ 64 <200000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-300000000 {
						opp-hz = /bits/ 64 <300000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-375000000 {
						opp-hz = /bits/ 64 <375000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-500000000 {
						opp-hz = /bits/ 64 <500000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
					opp-600000000 {
						opp-hz = /bits/ 64 <600000000>;
						required-opps = <&rpmhpd_opp_turbo_l1>;
					};
				};
			};

			mdss0_dp0: displayport-controller@ae90000 {
				compatible = "qcom,sc8280xp-dp";
				reg = <0 0xae90000 0 0x200>,
				      <0 0xae90200 0 0x200>,
				      <0 0xae90400 0 0x600>,
				      <0 0xae91000 0 0x400>,
				      <0 0xae91400 0 0x400>;
				interrupt-parent = <&mdss0>;
				interrupts = <12>;
				clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX0_AUX_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX0_LINK_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX0_PIXEL0_CLK>;
				clock-names = "core_iface", "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface",
					      "stream_pixel";

				assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>,
						  <&dispcc0 DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>;
				assigned-clock-parents = <&usb_0_qmpphy QMP_USB43DP_DP_LINK_CLK>,
							 <&usb_0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;

				phys = <&usb_0_qmpphy QMP_USB43DP_DP_PHY>;
				phy-names = "dp";

				#sound-dai-cells = <0>;

				operating-points-v2 = <&mdss0_dp0_opp_table>;
				power-domains = <&rpmhpd SC8280XP_MMCX>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;

						mdss0_dp0_in: endpoint {
							remote-endpoint = <&mdss0_intf0_out>;
						};
					};

					port@1 {
						reg = <1>;

						mdss0_dp0_out: endpoint {
						};
					};
				};

				mdss0_dp0_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss0_dp1: displayport-controller@ae98000 {
				compatible = "qcom,sc8280xp-dp";
				reg = <0 0xae98000 0 0x200>,
				      <0 0xae98200 0 0x200>,
				      <0 0xae98400 0 0x600>,
				      <0 0xae99000 0 0x400>,
				      <0 0xae99400 0 0x400>;
				interrupt-parent = <&mdss0>;
				interrupts = <13>;
				clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX1_AUX_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX1_LINK_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX1_LINK_INTF_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX1_PIXEL0_CLK>;
				clock-names = "core_iface", "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface", "stream_pixel";

				assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX1_LINK_CLK_SRC>,
						  <&dispcc0 DISP_CC_MDSS_DPTX1_PIXEL0_CLK_SRC>;
				assigned-clock-parents = <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
							 <&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;

				phys = <&usb_1_qmpphy QMP_USB43DP_DP_PHY>;
				phy-names = "dp";

				#sound-dai-cells = <0>;

				operating-points-v2 = <&mdss0_dp1_opp_table>;
				power-domains = <&rpmhpd SC8280XP_MMCX>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;

						mdss0_dp1_in: endpoint {
							remote-endpoint = <&mdss0_intf4_out>;
						};
					};

					port@1 {
						reg = <1>;

						mdss0_dp1_out: endpoint {
						};
					};
				};

				mdss0_dp1_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss0_dp2: displayport-controller@ae9a000 {
				compatible = "qcom,sc8280xp-dp";
				reg = <0 0xae9a000 0 0x200>,
				      <0 0xae9a200 0 0x200>,
				      <0 0xae9a400 0 0x600>,
				      <0 0xae9b000 0 0x400>,
				      <0 0xae9b400 0 0x400>;

				clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX2_AUX_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX2_PIXEL0_CLK>;
				clock-names = "core_iface", "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface", "stream_pixel";
				interrupt-parent = <&mdss0>;
				interrupts = <14>;
				phys = <&mdss0_dp2_phy>;
				phy-names = "dp";
				power-domains = <&rpmhpd SC8280XP_MMCX>;

				assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
						  <&dispcc0 DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
				assigned-clock-parents = <&mdss0_dp2_phy 0>, <&mdss0_dp2_phy 1>;
				operating-points-v2 = <&mdss0_dp2_opp_table>;

				#sound-dai-cells = <0>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss0_dp2_in: endpoint {
							remote-endpoint = <&mdss0_intf6_out>;
						};
					};

					port@1 {
						reg = <1>;
					};
				};

				mdss0_dp2_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss0_dp3: displayport-controller@aea0000 {
				compatible = "qcom,sc8280xp-dp";
				reg = <0 0xaea0000 0 0x200>,
				      <0 0xaea0200 0 0x200>,
				      <0 0xaea0400 0 0x600>,
				      <0 0xaea1000 0 0x400>,
				      <0 0xaea1400 0 0x400>;

				clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX3_AUX_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>,
					 <&dispcc0 DISP_CC_MDSS_DPTX3_PIXEL0_CLK>;
				clock-names = "core_iface", "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface", "stream_pixel";
				interrupt-parent = <&mdss0>;
				interrupts = <15>;
				phys = <&mdss0_dp3_phy>;
				phy-names = "dp";
				power-domains = <&rpmhpd SC8280XP_MMCX>;

				assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>,
						  <&dispcc0 DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>;
				assigned-clock-parents = <&mdss0_dp3_phy 0>, <&mdss0_dp3_phy 1>;
				operating-points-v2 = <&mdss0_dp3_opp_table>;

				#sound-dai-cells = <0>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss0_dp3_in: endpoint {
							remote-endpoint = <&mdss0_intf5_out>;
						};
					};

					port@1 {
						reg = <1>;
					};
				};

				mdss0_dp3_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};
		};

		mdss0_dp2_phy: phy@aec2a00 {
			compatible = "qcom,sc8280xp-dp-phy";
			reg = <0 0x0aec2a00 0 0x19c>,
			      <0 0x0aec2200 0 0xec>,
			      <0 0x0aec2600 0 0xec>,
			      <0 0x0aec2000 0 0x1c8>;

			clocks = <&dispcc0 DISP_CC_MDSS_DPTX2_AUX_CLK>,
				 <&dispcc0 DISP_CC_MDSS_AHB_CLK>;
			clock-names = "aux", "cfg_ahb";
			power-domains = <&rpmhpd SC8280XP_MX>;

			#clock-cells = <1>;
			#phy-cells = <0>;

			status = "disabled";
		};

		mdss0_dp3_phy: phy@aec5a00 {
			compatible = "qcom,sc8280xp-dp-phy";
			reg = <0 0x0aec5a00 0 0x19c>,
			      <0 0x0aec5200 0 0xec>,
			      <0 0x0aec5600 0 0xec>,
			      <0 0x0aec5000 0 0x1c8>;

			clocks = <&dispcc0 DISP_CC_MDSS_DPTX3_AUX_CLK>,
				 <&dispcc0 DISP_CC_MDSS_AHB_CLK>;
			clock-names = "aux", "cfg_ahb";
			power-domains = <&rpmhpd SC8280XP_MX>;

			#clock-cells = <1>;
			#phy-cells = <0>;

			status = "disabled";
		};

		dispcc0: clock-controller@af00000 {
			compatible = "qcom,sc8280xp-dispcc0";
			reg = <0 0x0af00000 0 0x20000>;

			clocks = <&gcc GCC_DISP_AHB_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&sleep_clk>,
				 <&usb_0_qmpphy QMP_USB43DP_DP_LINK_CLK>,
				 <&usb_0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
				 <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
				 <&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
				 <&mdss0_dp2_phy 0>,
				 <&mdss0_dp2_phy 1>,
				 <&mdss0_dp3_phy 0>,
				 <&mdss0_dp3_phy 1>,
				 <0>,
				 <0>,
				 <0>,
				 <0>;
			power-domains = <&rpmhpd SC8280XP_MMCX>;

			#clock-cells = <1>;
			#power-domain-cells = <1>;
			#reset-cells = <1>;

			status = "disabled";
		};

		pdc: interrupt-controller@b220000 {
			compatible = "qcom,sc8280xp-pdc", "qcom,pdc";
			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
			qcom,pdc-ranges = <0 480 40>,
					  <40 140 14>,
					  <54 263 1>,
					  <55 306 4>,
					  <59 312 3>,
					  <62 374 2>,
					  <64 434 2>,
					  <66 438 3>,
					  <69 86 1>,
					  <70 520 54>,
					  <124 609 28>,
					  <159 638 1>,
					  <160 720 8>,
					  <168 801 1>,
					  <169 728 30>,
					  <199 416 2>,
					  <201 449 1>,
					  <202 89 1>,
					  <203 451 1>,
					  <204 462 1>,
					  <205 264 1>,
					  <206 579 1>,
					  <207 653 1>,
					  <208 656 1>,
					  <209 659 1>,
					  <210 122 1>,
					  <211 699 1>,
					  <212 705 1>,
					  <213 450 1>,
					  <214 643 1>,
					  <216 646 5>,
					  <221 390 5>,
					  <226 700 3>,
					  <229 240 3>,
					  <232 269 1>,
					  <233 377 1>,
					  <234 372 1>,
					  <235 138 1>,
					  <236 857 1>,
					  <237 860 1>,
					  <238 137 1>,
					  <239 668 1>,
					  <240 366 1>,
					  <241 949 1>,
					  <242 815 5>,
					  <247 769 1>,
					  <248 768 1>,
					  <249 663 1>,
					  <250 799 2>,
					  <252 798 1>,
					  <253 765 1>,
					  <254 763 1>,
					  <255 454 1>,
					  <258 139 1>,
					  <259 786 2>,
					  <261 370 2>,
					  <263 158 2>;
			#interrupt-cells = <2>;
			interrupt-parent = <&intc>;
			interrupt-controller;
		};

		tsens2: thermal-sensor@c251000 {
			compatible = "qcom,sc8280xp-tsens", "qcom,tsens-v2";
			reg = <0 0x0c251000 0 0x1ff>,
			      <0 0x0c224000 0 0x8>;
			#qcom,sensors = <11>;
			interrupts-extended = <&pdc 122 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 124 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		tsens3: thermal-sensor@c252000 {
			compatible = "qcom,sc8280xp-tsens", "qcom,tsens-v2";
			reg = <0 0x0c252000 0 0x1ff>,
			      <0 0x0c225000 0 0x8>;
			#qcom,sensors = <5>;
			interrupts-extended = <&pdc 123 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 125 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		tsens0: thermal-sensor@c263000 {
			compatible = "qcom,sc8280xp-tsens", "qcom,tsens-v2";
			reg = <0 0x0c263000 0 0x1ff>, /* TM */
			      <0 0x0c222000 0 0x8>; /* SROT */
			#qcom,sensors = <14>;
			interrupts-extended = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 28 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		restart@c264000 {
			compatible = "qcom,pshold";
			reg = <0 0x0c264000 0 0x4>;
			/* TZ seems to block access */
			status = "reserved";
		};

		tsens1: thermal-sensor@c265000 {
			compatible = "qcom,sc8280xp-tsens", "qcom,tsens-v2";
			reg = <0 0x0c265000 0 0x1ff>, /* TM */
			      <0 0x0c223000 0 0x8>; /* SROT */
			#qcom,sensors = <16>;
			interrupts-extended = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 29 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		aoss_qmp: power-management@c300000 {
			compatible = "qcom,sc8280xp-aoss-qmp", "qcom,aoss-qmp";
			reg = <0 0x0c300000 0 0x400>;
			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP IRQ_TYPE_EDGE_RISING>;
			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;

			#clock-cells = <0>;
		};

		sram@c3f0000 {
			compatible = "qcom,rpmh-stats";
			reg = <0 0x0c3f0000 0 0x400>;
			qcom,qmp = <&aoss_qmp>;
		};

		spmi_bus: spmi@c440000 {
			compatible = "qcom,spmi-pmic-arb";
			reg = <0 0x0c440000 0 0x1100>,
			      <0 0x0c600000 0 0x2000000>,
			      <0 0x0e600000 0 0x100000>,
			      <0 0x0e700000 0 0xa0000>,
			      <0 0x0c40a000 0 0x26000>;
			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
			interrupt-names = "periph_irq";
			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
			qcom,ee = <0>;
			qcom,channel = <0>;
			#address-cells = <2>;
			#size-cells = <0>;
			interrupt-controller;
			#interrupt-cells = <4>;
		};

		tlmm: pinctrl@f100000 {
			compatible = "qcom,sc8280xp-tlmm";
			reg = <0 0x0f100000 0 0x300000>;
			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			gpio-ranges = <&tlmm 0 0 230>;
			wakeup-parent = <&pdc>;

			cci0_default: cci0-default-state {
				cci0_i2c0_default: cci0-i2c0-default-pins {
					/* cci_i2c_sda0, cci_i2c_scl0 */
					pins = "gpio113", "gpio114";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-up;
				};

				cci0_i2c1_default: cci0-i2c1-default-pins {
					/* cci_i2c_sda1, cci_i2c_scl1 */
					pins = "gpio115", "gpio116";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			cci0_sleep: cci0-sleep-state {
				cci0_i2c0_sleep: cci0-i2c0-sleep-pins {
					/* cci_i2c_sda0, cci_i2c_scl0 */
					pins = "gpio113", "gpio114";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-down;
				};

				cci0_i2c1_sleep: cci0-i2c1-sleep-pins {
					/* cci_i2c_sda1, cci_i2c_scl1 */
					pins = "gpio115", "gpio116";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-down;
				};
			};

			cci1_default: cci1-default-state {
				cci1_i2c0_default: cci1-i2c0-default-pins {
					/* cci_i2c_sda2, cci_i2c_scl2 */
					pins = "gpio10","gpio11";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-up;
				};

				cci1_i2c1_default: cci1-i2c1-default-pins {
					/* cci_i2c_sda3, cci_i2c_scl3 */
					pins = "gpio123","gpio124";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			cci1_sleep: cci1-sleep-state {
				cci1_i2c0_sleep: cci1-i2c0-sleep-pins {
					/* cci_i2c_sda2, cci_i2c_scl2 */
					pins = "gpio10","gpio11";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-down;
				};

				cci1_i2c1_sleep: cci1-i2c1-sleep-pins {
					/* cci_i2c_sda3, cci_i2c_scl3 */
					pins = "gpio123","gpio124";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-down;
				};
			};

			cci2_default: cci2-default-state {
				cci2_i2c0_default: cci2-i2c0-default-pins {
					/* cci_i2c_sda4, cci_i2c_scl4 */
					pins = "gpio117","gpio118";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-up;
				};

				cci2_i2c1_default: cci2-i2c1-default-pins {
					/* cci_i2c_sda5, cci_i2c_scl5 */
					pins = "gpio12","gpio13";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			cci2_sleep: cci2-sleep-state {
				cci2_i2c0_sleep: cci2-i2c0-sleep-pins {
					/* cci_i2c_sda4, cci_i2c_scl4 */
					pins = "gpio117","gpio118";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-down;
				};

				cci2_i2c1_sleep: cci2-i2c1-sleep-pins {
					/* cci_i2c_sda5, cci_i2c_scl5 */
					pins = "gpio12","gpio13";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-down;
				};
			};

			cci3_default: cci3-default-state {
				cci3_i2c0_default: cci3-i2c0-default-pins {
					/* cci_i2c_sda6, cci_i2c_scl6 */
					pins = "gpio145","gpio146";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-up;
				};

				cci3_i2c1_default: cci3-i2c1-default-pins {
					/* cci_i2c_sda7, cci_i2c_scl7 */
					pins = "gpio164","gpio165";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			cci3_sleep: cci3-sleep-state {
				cci3_i2c0_sleep: cci3-i2c0-sleep-pins {
					/* cci_i2c_sda6, cci_i2c_scl6 */
					pins = "gpio145","gpio146";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-down;
				};

				cci3_i2c1_sleep: cci3-i2c1-sleep-pins {
					/* cci_i2c_sda7, cci_i2c_scl7 */
					pins = "gpio164","gpio165";
					function = "cci_i2c";
					drive-strength = <2>;
					bias-pull-down;
				};
			};
		};

		apps_smmu: iommu@15000000 {
			compatible = "qcom,sc8280xp-smmu-500", "arm,mmu-500";
			reg = <0 0x15000000 0 0x100000>;
			#iommu-cells = <2>;
			#global-interrupts = <2>;
			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 706 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 689 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 708 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 709 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 710 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 711 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 712 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 713 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 714 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 715 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 912 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 911 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 910 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 909 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 908 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 907 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 906 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 905 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 904 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 903 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 902 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 901 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 900 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 899 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 898 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 896 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 895 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 894 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 893 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 892 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 891 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 890 IRQ_TYPE_LEVEL_HIGH>;
		};

		intc: interrupt-controller@17a00000 {
			compatible = "arm,gic-v3";
			interrupt-controller;
			#interrupt-cells = <3>;
			reg = <0x0 0x17a00000 0x0 0x10000>,	/* GICD */
			      <0x0 0x17a60000 0x0 0x100000>;	/* GICR * 8 */
			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
			#redistributor-regions = <1>;
			redistributor-stride = <0 0x20000>;

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			its: msi-controller@17a40000 {
				compatible = "arm,gic-v3-its";
				reg = <0 0x17a40000 0 0x20000>;
				msi-controller;
				#msi-cells = <1>;
			};
		};

		watchdog@17c10000 {
			compatible = "qcom,apss-wdt-sc8280xp", "qcom,kpss-wdt";
			reg = <0 0x17c10000 0 0x1000>;
			clocks = <&sleep_clk>;
			interrupts = <GIC_SPI 0 IRQ_TYPE_EDGE_RISING>;
		};

		timer@17c20000 {
			compatible = "arm,armv7-timer-mem";
			reg = <0x0 0x17c20000 0x0 0x1000>;
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x0 0x0 0x20000000>;

			frame@17c21000 {
				frame-number = <0>;
				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c21000 0x1000>,
				      <0x17c22000 0x1000>;
			};

			frame@17c23000 {
				frame-number = <1>;
				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c23000 0x1000>;
				status = "disabled";
			};

			frame@17c25000 {
				frame-number = <2>;
				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c25000 0x1000>;
				status = "disabled";
			};

			frame@17c27000 {
				frame-number = <3>;
				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c26000 0x1000>;
				status = "disabled";
			};

			frame@17c29000 {
				frame-number = <4>;
				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c29000 0x1000>;
				status = "disabled";
			};

			frame@17c2b000 {
				frame-number = <5>;
				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c2b000 0x1000>;
				status = "disabled";
			};

			frame@17c2d000 {
				frame-number = <6>;
				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c2d000 0x1000>;
				status = "disabled";
			};
		};

		apps_rsc: rsc@18200000 {
			compatible = "qcom,rpmh-rsc";
			reg = <0x0 0x18200000 0x0 0x10000>,
				<0x0 0x18210000 0x0 0x10000>,
				<0x0 0x18220000 0x0 0x10000>;
			reg-names = "drv-0", "drv-1", "drv-2";
			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
			qcom,tcs-offset = <0xd00>;
			qcom,drv-id = <2>;
			qcom,tcs-config = <ACTIVE_TCS  2>, <SLEEP_TCS   3>,
					  <WAKE_TCS    3>, <CONTROL_TCS 1>;
			label = "apps_rsc";
			power-domains = <&CLUSTER_PD>;

			apps_bcm_voter: bcm-voter {
				compatible = "qcom,bcm-voter";
			};

			rpmhcc: clock-controller {
				compatible = "qcom,sc8280xp-rpmh-clk";
				#clock-cells = <1>;
				clock-names = "xo";
				clocks = <&xo_board_clk>;
			};

			rpmhpd: power-controller {
				compatible = "qcom,sc8280xp-rpmhpd";
				#power-domain-cells = <1>;
				operating-points-v2 = <&rpmhpd_opp_table>;

				rpmhpd_opp_table: opp-table {
					compatible = "operating-points-v2";

					rpmhpd_opp_ret: opp1 {
						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
					};

					rpmhpd_opp_min_svs: opp2 {
						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
					};

					rpmhpd_opp_low_svs: opp3 {
						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
					};

					rpmhpd_opp_svs: opp4 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
					};

					rpmhpd_opp_svs_l1: opp5 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
					};

					rpmhpd_opp_nom: opp6 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
					};

					rpmhpd_opp_nom_l1: opp7 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
					};

					rpmhpd_opp_nom_l2: opp8 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
					};

					rpmhpd_opp_turbo: opp9 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
					};

					rpmhpd_opp_turbo_l1: opp10 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
					};
				};
			};
		};

		epss_l3: interconnect@18590000 {
			compatible = "qcom,sc8280xp-epss-l3", "qcom,epss-l3";
			reg = <0 0x18590000 0 0x1000>;

			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
			clock-names = "xo", "alternate";

			#interconnect-cells = <1>;
		};

		cpufreq_hw: cpufreq@18591000 {
			compatible = "qcom,sc8280xp-cpufreq-epss", "qcom,cpufreq-epss";
			reg = <0 0x18591000 0 0x1000>,
			      <0 0x18592000 0 0x1000>;
			reg-names = "freq-domain0", "freq-domain1";

			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "dcvsh-irq-0",
					  "dcvsh-irq-1";

			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
			clock-names = "xo", "alternate";

			#freq-domain-cells = <1>;
			#clock-cells = <1>;
		};

		remoteproc_nsp0: remoteproc@1b300000 {
			compatible = "qcom,sc8280xp-nsp0-pas";
			reg = <0 0x1b300000 0 0x100>;

			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp0_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp0_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp0_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp0_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SC8280XP_NSP>;
			power-domain-names = "nsp";

			memory-region = <&pil_nsp0_mem>;

			qcom,smem-states = <&smp2p_nsp0_out 0>;
			qcom,smem-state-names = "stop";

			interconnects = <&nspa_noc MASTER_CDSP_PROC 0 &mc_virt SLAVE_EBI1 0>;

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_CDSP
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "nsp0";
				qcom,remote-pid = <5>;

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,glink-channels = "fastrpcglink-apps-dsp";
					label = "cdsp";
					#address-cells = <1>;
					#size-cells = <0>;

					compute-cb@1 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <1>;
						iommus = <&apps_smmu 0x3181 0x0420>;
					};

					compute-cb@2 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <2>;
						iommus = <&apps_smmu 0x3182 0x0420>;
					};

					compute-cb@3 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <3>;
						iommus = <&apps_smmu 0x3183 0x0420>;
					};

					compute-cb@4 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <4>;
						iommus = <&apps_smmu 0x3184 0x0420>;
					};

					compute-cb@5 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <5>;
						iommus = <&apps_smmu 0x3185 0x0420>;
					};

					compute-cb@6 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <6>;
						iommus = <&apps_smmu 0x3186 0x0420>;
					};

					compute-cb@7 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <7>;
						iommus = <&apps_smmu 0x3187 0x0420>;
					};

					compute-cb@8 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <8>;
						iommus = <&apps_smmu 0x3188 0x0420>;
					};

					compute-cb@9 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <9>;
						iommus = <&apps_smmu 0x318b 0x0420>;
					};

					compute-cb@10 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <10>;
						iommus = <&apps_smmu 0x318b 0x0420>;
					};

					compute-cb@11 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <11>;
						iommus = <&apps_smmu 0x318c 0x0420>;
					};

					compute-cb@12 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <12>;
						iommus = <&apps_smmu 0x318d 0x0420>;
					};

					compute-cb@13 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <13>;
						iommus = <&apps_smmu 0x318e 0x0420>;
					};

					compute-cb@14 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <14>;
						iommus = <&apps_smmu 0x318f 0x0420>;
					};
				};
			};
		};

		remoteproc_nsp1: remoteproc@21300000 {
			compatible = "qcom,sc8280xp-nsp1-pas";
			reg = <0 0x21300000 0 0x100>;

			interrupts-extended = <&intc GIC_SPI 887 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp1_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp1_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp1_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp1_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SC8280XP_NSP>;
			power-domain-names = "nsp";

			memory-region = <&pil_nsp1_mem>;

			qcom,smem-states = <&smp2p_nsp1_out 0>;
			qcom,smem-state-names = "stop";

			interconnects = <&nspb_noc MASTER_CDSP_PROC_B 0 &mc_virt SLAVE_EBI1 0>;

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_NSP1
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_NSP1
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "nsp1";
				qcom,remote-pid = <12>;
			};
		};

		mdss1: display-subsystem@22000000 {
			compatible = "qcom,sc8280xp-mdss";
			reg = <0 0x22000000 0 0x1000>;
			reg-names = "mdss";

			clocks = <&gcc GCC_DISP_AHB_CLK>,
				 <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
				 <&dispcc1 DISP_CC_MDSS_MDP_CLK>;
			clock-names = "iface",
				      "ahb",
				      "core";
			interconnects = <&mmss_noc MASTER_MDP_CORE1_0 0 &mc_virt SLAVE_EBI1 0>,
					<&mmss_noc MASTER_MDP_CORE1_1 0 &mc_virt SLAVE_EBI1 0>;
			interconnect-names = "mdp0-mem", "mdp1-mem";
			interrupts = <GIC_SPI 865 IRQ_TYPE_LEVEL_HIGH>;

			iommus = <&apps_smmu 0x1800 0x402>;
			power-domains = <&dispcc1 MDSS_GDSC>;
			resets = <&dispcc1 DISP_CC_MDSS_CORE_BCR>;

			interrupt-controller;
			#interrupt-cells = <1>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";

			mdss1_mdp: display-controller@22001000 {
				compatible = "qcom,sc8280xp-dpu";
				reg = <0 0x22001000 0 0x8f000>,
				      <0 0x220b0000 0 0x2008>;
				reg-names = "mdp", "vbif";

				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
					 <&gcc GCC_DISP_SF_AXI_CLK>,
					 <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc1 DISP_CC_MDSS_MDP_LUT_CLK>,
					 <&dispcc1 DISP_CC_MDSS_MDP_CLK>,
					 <&dispcc1 DISP_CC_MDSS_VSYNC_CLK>;
				clock-names = "bus",
					      "nrt_bus",
					      "iface",
					      "lut",
					      "core",
					      "vsync";
				interrupt-parent = <&mdss1>;
				interrupts = <0>;
				power-domains = <&rpmhpd SC8280XP_MMCX>;

				assigned-clocks = <&dispcc1 DISP_CC_MDSS_VSYNC_CLK>;
				assigned-clock-rates = <19200000>;
				operating-points-v2 = <&mdss1_mdp_opp_table>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss1_intf0_out: endpoint {
							remote-endpoint = <&mdss1_dp0_in>;
						};
					};

					port@4 {
						reg = <4>;
						mdss1_intf4_out: endpoint {
							remote-endpoint = <&mdss1_dp1_in>;
						};
					};

					port@5 {
						reg = <5>;
						mdss1_intf5_out: endpoint {
							remote-endpoint = <&mdss1_dp3_in>;
						};
					};

					port@6 {
						reg = <6>;
						mdss1_intf6_out: endpoint {
							remote-endpoint = <&mdss1_dp2_in>;
						};
					};
				};

				mdss1_mdp_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-200000000 {
						opp-hz = /bits/ 64 <200000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-300000000 {
						opp-hz = /bits/ 64 <300000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-375000000 {
						opp-hz = /bits/ 64 <375000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-500000000 {
						opp-hz = /bits/ 64 <500000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
					opp-600000000 {
						opp-hz = /bits/ 64 <600000000>;
						required-opps = <&rpmhpd_opp_turbo_l1>;
					};
				};
			};

			mdss1_dp0: displayport-controller@22090000 {
				compatible = "qcom,sc8280xp-dp";
				reg = <0 0x22090000 0 0x200>,
				      <0 0x22090200 0 0x200>,
				      <0 0x22090400 0 0x600>,
				      <0 0x22091000 0 0x400>,
				      <0 0x22091400 0 0x400>;

				clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX0_AUX_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX0_LINK_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX0_PIXEL0_CLK>;
				clock-names = "core_iface", "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface", "stream_pixel";
				interrupt-parent = <&mdss1>;
				interrupts = <12>;
				phys = <&mdss1_dp0_phy>;
				phy-names = "dp";
				power-domains = <&rpmhpd SC8280XP_MMCX>;

				assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>,
						  <&dispcc1 DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>;
				assigned-clock-parents = <&mdss1_dp0_phy 0>, <&mdss1_dp0_phy 1>;
				operating-points-v2 = <&mdss1_dp0_opp_table>;

				#sound-dai-cells = <0>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss1_dp0_in: endpoint {
							remote-endpoint = <&mdss1_intf0_out>;
						};
					};

					port@1 {
						reg = <1>;
					};
				};

				mdss1_dp0_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss1_dp1: displayport-controller@22098000 {
				compatible = "qcom,sc8280xp-dp";
				reg = <0 0x22098000 0 0x200>,
				      <0 0x22098200 0 0x200>,
				      <0 0x22098400 0 0x600>,
				      <0 0x22099000 0 0x400>,
				      <0 0x22099400 0 0x400>;

				clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX1_AUX_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX1_LINK_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX1_LINK_INTF_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX1_PIXEL0_CLK>;
				clock-names = "core_iface", "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface", "stream_pixel";
				interrupt-parent = <&mdss1>;
				interrupts = <13>;
				phys = <&mdss1_dp1_phy>;
				phy-names = "dp";
				power-domains = <&rpmhpd SC8280XP_MMCX>;

				assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX1_LINK_CLK_SRC>,
						  <&dispcc1 DISP_CC_MDSS_DPTX1_PIXEL0_CLK_SRC>;
				assigned-clock-parents = <&mdss1_dp1_phy 0>, <&mdss1_dp1_phy 1>;
				operating-points-v2 = <&mdss1_dp1_opp_table>;

				#sound-dai-cells = <0>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss1_dp1_in: endpoint {
							remote-endpoint = <&mdss1_intf4_out>;
						};
					};

					port@1 {
						reg = <1>;
					};
				};

				mdss1_dp1_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss1_dp2: displayport-controller@2209a000 {
				compatible = "qcom,sc8280xp-dp";
				reg = <0 0x2209a000 0 0x200>,
				      <0 0x2209a200 0 0x200>,
				      <0 0x2209a400 0 0x600>,
				      <0 0x2209b000 0 0x400>,
				      <0 0x2209b400 0 0x400>;

				clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX2_AUX_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX2_LINK_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX2_PIXEL0_CLK>;
				clock-names = "core_iface", "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface", "stream_pixel";
				interrupt-parent = <&mdss1>;
				interrupts = <14>;
				phys = <&mdss1_dp2_phy>;
				phy-names = "dp";
				power-domains = <&rpmhpd SC8280XP_MMCX>;

				assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
						  <&dispcc1 DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
				assigned-clock-parents = <&mdss1_dp2_phy 0>, <&mdss1_dp2_phy 1>;
				operating-points-v2 = <&mdss1_dp2_opp_table>;

				#sound-dai-cells = <0>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss1_dp2_in: endpoint {
							remote-endpoint = <&mdss1_intf6_out>;
						};
					};

					port@1 {
						reg = <1>;
					};
				};

				mdss1_dp2_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss1_dp3: displayport-controller@220a0000 {
				compatible = "qcom,sc8280xp-dp";
				reg = <0 0x220a0000 0 0x200>,
				      <0 0x220a0200 0 0x200>,
				      <0 0x220a0400 0 0x600>,
				      <0 0x220a1000 0 0x400>,
				      <0 0x220a1400 0 0x400>;

				clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX3_AUX_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX3_LINK_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>,
					 <&dispcc1 DISP_CC_MDSS_DPTX3_PIXEL0_CLK>;
				clock-names = "core_iface", "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface", "stream_pixel";
				interrupt-parent = <&mdss1>;
				interrupts = <15>;
				phys = <&mdss1_dp3_phy>;
				phy-names = "dp";
				power-domains = <&rpmhpd SC8280XP_MMCX>;

				assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>,
						  <&dispcc1 DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>;
				assigned-clock-parents = <&mdss1_dp3_phy 0>, <&mdss1_dp3_phy 1>;
				operating-points-v2 = <&mdss1_dp3_opp_table>;

				#sound-dai-cells = <0>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss1_dp3_in: endpoint {
							remote-endpoint = <&mdss1_intf5_out>;
						};
					};

					port@1 {
						reg = <1>;
					};
				};

				mdss1_dp3_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};
		};

		mdss1_dp2_phy: phy@220c2a00 {
			compatible = "qcom,sc8280xp-dp-phy";
			reg = <0 0x220c2a00 0 0x19c>,
			      <0 0x220c2200 0 0xec>,
			      <0 0x220c2600 0 0xec>,
			      <0 0x220c2000 0 0x1c8>;

			clocks = <&dispcc1 DISP_CC_MDSS_DPTX2_AUX_CLK>,
				 <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
			clock-names = "aux", "cfg_ahb";
			power-domains = <&rpmhpd SC8280XP_MX>;

			#clock-cells = <1>;
			#phy-cells = <0>;

			status = "disabled";
		};

		mdss1_dp3_phy: phy@220c5a00 {
			compatible = "qcom,sc8280xp-dp-phy";
			reg = <0 0x220c5a00 0 0x19c>,
			      <0 0x220c5200 0 0xec>,
			      <0 0x220c5600 0 0xec>,
			      <0 0x220c5000 0 0x1c8>;

			clocks = <&dispcc1 DISP_CC_MDSS_DPTX3_AUX_CLK>,
				 <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
			clock-names = "aux", "cfg_ahb";
			power-domains = <&rpmhpd SC8280XP_MX>;

			#clock-cells = <1>;
			#phy-cells = <0>;

			status = "disabled";
		};

		dispcc1: clock-controller@22100000 {
			compatible = "qcom,sc8280xp-dispcc1";
			reg = <0 0x22100000 0 0x20000>;

			clocks = <&gcc GCC_DISP_AHB_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <0>,
				 <&mdss1_dp0_phy 0>,
				 <&mdss1_dp0_phy 1>,
				 <&mdss1_dp1_phy 0>,
				 <&mdss1_dp1_phy 1>,
				 <&mdss1_dp2_phy 0>,
				 <&mdss1_dp2_phy 1>,
				 <&mdss1_dp3_phy 0>,
				 <&mdss1_dp3_phy 1>,
				 <0>,
				 <0>,
				 <0>,
				 <0>;
			power-domains = <&rpmhpd SC8280XP_MMCX>;

			#clock-cells = <1>;
			#power-domain-cells = <1>;
			#reset-cells = <1>;

			status = "disabled";
		};

		ethernet1: ethernet@23000000 {
			compatible = "qcom,sc8280xp-ethqos";
			reg = <0x0 0x23000000 0x0 0x10000>,
			      <0x0 0x23016000 0x0 0x100>;
			reg-names = "stmmaceth", "rgmii";

			clocks = <&gcc GCC_EMAC1_AXI_CLK>,
				 <&gcc GCC_EMAC1_SLV_AHB_CLK>,
				 <&gcc GCC_EMAC1_PTP_CLK>,
				 <&gcc GCC_EMAC1_RGMII_CLK>;
			clock-names = "stmmaceth",
				      "pclk",
				      "ptp_ref",
				      "rgmii";

			interrupts = <GIC_SPI 929 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 919 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "macirq", "eth_lpi";

			iommus = <&apps_smmu 0x40 0xf>;
			power-domains = <&gcc EMAC_1_GDSC>;

			snps,tso;
			snps,pbl = <32>;
			rx-fifo-depth = <4096>;
			tx-fifo-depth = <4096>;

			status = "disabled";
		};
	};

	sound: sound {
	};

	thermal-zones {
		cpu0-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 1>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu1-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 2>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu2-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 3>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu3-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 4>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu4-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 5>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu5-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 6>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu6-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 7>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu7-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 8>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cluster0-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 9>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		gpu-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens2 2>;

			cooling-maps {
				map0 {
					trip = <&gpu_alert0>;
					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};

			trips {
				gpu_alert0: trip-point0 {
					temperature = <85000>;
					hysteresis = <1000>;
					type = "passive";
				};

				trip-point1 {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		mem-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens1 15>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
	};
};