| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2020, Konrad Dybcio <konradybcio@gmail.com> |
| * Copyright (c) 2020, AngeloGioacchino Del Regno <kholk11@gmail.com> |
| */ |
| |
| #include <dt-bindings/clock/qcom,gcc-sdm660.h> |
| #include <dt-bindings/clock/qcom,gpucc-sdm660.h> |
| #include <dt-bindings/clock/qcom,mmcc-sdm660.h> |
| #include <dt-bindings/clock/qcom,rpmcc.h> |
| #include <dt-bindings/firmware/qcom,scm.h> |
| #include <dt-bindings/interconnect/qcom,sdm660.h> |
| #include <dt-bindings/power/qcom-rpmpd.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/thermal/thermal.h> |
| #include <dt-bindings/soc/qcom,apr.h> |
| |
| / { |
| interrupt-parent = <&intc>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| aliases { |
| mmc1 = &sdhc_1; |
| mmc2 = &sdhc_2; |
| }; |
| |
| chosen { }; |
| |
| clocks { |
| xo_board: xo-board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <19200000>; |
| clock-output-names = "xo_board"; |
| }; |
| |
| sleep_clk: sleep-clk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32764>; |
| clock-output-names = "sleep_clk"; |
| }; |
| }; |
| |
| cpus { |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| CPU0: cpu@100 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0 0x100>; |
| enable-method = "psci"; |
| cpu-idle-states = <&PERF_CPU_SLEEP_0 |
| &PERF_CPU_SLEEP_1 |
| &PERF_CLUSTER_SLEEP_0 |
| &PERF_CLUSTER_SLEEP_1 |
| &PERF_CLUSTER_SLEEP_2>; |
| capacity-dmips-mhz = <1126>; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_1>; |
| L2_1: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| }; |
| |
| CPU1: cpu@101 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0 0x101>; |
| enable-method = "psci"; |
| cpu-idle-states = <&PERF_CPU_SLEEP_0 |
| &PERF_CPU_SLEEP_1 |
| &PERF_CLUSTER_SLEEP_0 |
| &PERF_CLUSTER_SLEEP_1 |
| &PERF_CLUSTER_SLEEP_2>; |
| capacity-dmips-mhz = <1126>; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_1>; |
| }; |
| |
| CPU2: cpu@102 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0 0x102>; |
| enable-method = "psci"; |
| cpu-idle-states = <&PERF_CPU_SLEEP_0 |
| &PERF_CPU_SLEEP_1 |
| &PERF_CLUSTER_SLEEP_0 |
| &PERF_CLUSTER_SLEEP_1 |
| &PERF_CLUSTER_SLEEP_2>; |
| capacity-dmips-mhz = <1126>; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_1>; |
| }; |
| |
| CPU3: cpu@103 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0 0x103>; |
| enable-method = "psci"; |
| cpu-idle-states = <&PERF_CPU_SLEEP_0 |
| &PERF_CPU_SLEEP_1 |
| &PERF_CLUSTER_SLEEP_0 |
| &PERF_CLUSTER_SLEEP_1 |
| &PERF_CLUSTER_SLEEP_2>; |
| capacity-dmips-mhz = <1126>; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_1>; |
| }; |
| |
| CPU4: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0 0x0>; |
| enable-method = "psci"; |
| cpu-idle-states = <&PWR_CPU_SLEEP_0 |
| &PWR_CPU_SLEEP_1 |
| &PWR_CLUSTER_SLEEP_0 |
| &PWR_CLUSTER_SLEEP_1 |
| &PWR_CLUSTER_SLEEP_2>; |
| capacity-dmips-mhz = <1024>; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_0>; |
| L2_0: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| }; |
| |
| CPU5: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0 0x1>; |
| enable-method = "psci"; |
| cpu-idle-states = <&PWR_CPU_SLEEP_0 |
| &PWR_CPU_SLEEP_1 |
| &PWR_CLUSTER_SLEEP_0 |
| &PWR_CLUSTER_SLEEP_1 |
| &PWR_CLUSTER_SLEEP_2>; |
| capacity-dmips-mhz = <1024>; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_0>; |
| }; |
| |
| CPU6: cpu@2 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0 0x2>; |
| enable-method = "psci"; |
| cpu-idle-states = <&PWR_CPU_SLEEP_0 |
| &PWR_CPU_SLEEP_1 |
| &PWR_CLUSTER_SLEEP_0 |
| &PWR_CLUSTER_SLEEP_1 |
| &PWR_CLUSTER_SLEEP_2>; |
| capacity-dmips-mhz = <1024>; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_0>; |
| }; |
| |
| CPU7: cpu@3 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0 0x3>; |
| enable-method = "psci"; |
| cpu-idle-states = <&PWR_CPU_SLEEP_0 |
| &PWR_CPU_SLEEP_1 |
| &PWR_CLUSTER_SLEEP_0 |
| &PWR_CLUSTER_SLEEP_1 |
| &PWR_CLUSTER_SLEEP_2>; |
| capacity-dmips-mhz = <1024>; |
| #cooling-cells = <2>; |
| next-level-cache = <&L2_0>; |
| }; |
| |
| cpu-map { |
| cluster0 { |
| core0 { |
| cpu = <&CPU4>; |
| }; |
| |
| core1 { |
| cpu = <&CPU5>; |
| }; |
| |
| core2 { |
| cpu = <&CPU6>; |
| }; |
| |
| core3 { |
| cpu = <&CPU7>; |
| }; |
| }; |
| |
| cluster1 { |
| core0 { |
| cpu = <&CPU0>; |
| }; |
| |
| core1 { |
| cpu = <&CPU1>; |
| }; |
| |
| core2 { |
| cpu = <&CPU2>; |
| }; |
| |
| core3 { |
| cpu = <&CPU3>; |
| }; |
| }; |
| }; |
| |
| idle-states { |
| entry-method = "psci"; |
| |
| PWR_CPU_SLEEP_0: cpu-sleep-0-0 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "pwr-retention"; |
| arm,psci-suspend-param = <0x40000002>; |
| entry-latency-us = <338>; |
| exit-latency-us = <423>; |
| min-residency-us = <200>; |
| }; |
| |
| PWR_CPU_SLEEP_1: cpu-sleep-0-1 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "pwr-power-collapse"; |
| arm,psci-suspend-param = <0x40000003>; |
| entry-latency-us = <515>; |
| exit-latency-us = <1821>; |
| min-residency-us = <1000>; |
| local-timer-stop; |
| }; |
| |
| PERF_CPU_SLEEP_0: cpu-sleep-1-0 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "perf-retention"; |
| arm,psci-suspend-param = <0x40000002>; |
| entry-latency-us = <154>; |
| exit-latency-us = <87>; |
| min-residency-us = <200>; |
| }; |
| |
| PERF_CPU_SLEEP_1: cpu-sleep-1-1 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "perf-power-collapse"; |
| arm,psci-suspend-param = <0x40000003>; |
| entry-latency-us = <262>; |
| exit-latency-us = <301>; |
| min-residency-us = <1000>; |
| local-timer-stop; |
| }; |
| |
| PWR_CLUSTER_SLEEP_0: cluster-sleep-0-0 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "pwr-cluster-dynamic-retention"; |
| arm,psci-suspend-param = <0x400000F2>; |
| entry-latency-us = <284>; |
| exit-latency-us = <384>; |
| min-residency-us = <9987>; |
| local-timer-stop; |
| }; |
| |
| PWR_CLUSTER_SLEEP_1: cluster-sleep-0-1 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "pwr-cluster-retention"; |
| arm,psci-suspend-param = <0x400000F3>; |
| entry-latency-us = <338>; |
| exit-latency-us = <423>; |
| min-residency-us = <9987>; |
| local-timer-stop; |
| }; |
| |
| PWR_CLUSTER_SLEEP_2: cluster-sleep-0-2 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "pwr-cluster-retention"; |
| arm,psci-suspend-param = <0x400000F4>; |
| entry-latency-us = <515>; |
| exit-latency-us = <1821>; |
| min-residency-us = <9987>; |
| local-timer-stop; |
| }; |
| |
| PERF_CLUSTER_SLEEP_0: cluster-sleep-1-0 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "perf-cluster-dynamic-retention"; |
| arm,psci-suspend-param = <0x400000F2>; |
| entry-latency-us = <272>; |
| exit-latency-us = <329>; |
| min-residency-us = <9987>; |
| local-timer-stop; |
| }; |
| |
| PERF_CLUSTER_SLEEP_1: cluster-sleep-1-1 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "perf-cluster-retention"; |
| arm,psci-suspend-param = <0x400000F3>; |
| entry-latency-us = <332>; |
| exit-latency-us = <368>; |
| min-residency-us = <9987>; |
| local-timer-stop; |
| }; |
| |
| PERF_CLUSTER_SLEEP_2: cluster-sleep-1-2 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "perf-cluster-retention"; |
| arm,psci-suspend-param = <0x400000F4>; |
| entry-latency-us = <545>; |
| exit-latency-us = <1609>; |
| min-residency-us = <9987>; |
| local-timer-stop; |
| }; |
| }; |
| }; |
| |
| firmware { |
| scm { |
| compatible = "qcom,scm-msm8998", "qcom,scm"; |
| }; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| /* We expect the bootloader to fill in the reg */ |
| reg = <0x0 0x80000000 0x0 0x0>; |
| }; |
| |
| dsi_opp_table: opp-table-dsi { |
| compatible = "operating-points-v2"; |
| |
| opp-131250000 { |
| opp-hz = /bits/ 64 <131250000>; |
| required-opps = <&rpmpd_opp_svs>; |
| }; |
| |
| opp-210000000 { |
| opp-hz = /bits/ 64 <210000000>; |
| required-opps = <&rpmpd_opp_svs_plus>; |
| }; |
| |
| opp-262500000 { |
| opp-hz = /bits/ 64 <262500000>; |
| required-opps = <&rpmpd_opp_nom>; |
| }; |
| }; |
| |
| pmu { |
| compatible = "arm,armv8-pmuv3"; |
| interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| rpm: remoteproc { |
| compatible = "qcom,sdm660-rpm-proc", "qcom,rpm-proc"; |
| |
| glink-edge { |
| compatible = "qcom,glink-rpm"; |
| |
| interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>; |
| qcom,rpm-msg-ram = <&rpm_msg_ram>; |
| mboxes = <&apcs_glb 0>; |
| |
| rpm_requests: rpm-requests { |
| compatible = "qcom,rpm-sdm660", "qcom,glink-smd-rpm"; |
| qcom,glink-channels = "rpm_requests"; |
| |
| rpmcc: clock-controller { |
| compatible = "qcom,rpmcc-sdm660", "qcom,rpmcc"; |
| #clock-cells = <1>; |
| }; |
| |
| rpmpd: power-controller { |
| compatible = "qcom,sdm660-rpmpd"; |
| #power-domain-cells = <1>; |
| operating-points-v2 = <&rpmpd_opp_table>; |
| |
| rpmpd_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| rpmpd_opp_ret: opp1 { |
| opp-level = <RPM_SMD_LEVEL_RETENTION>; |
| }; |
| |
| rpmpd_opp_ret_plus: opp2 { |
| opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>; |
| }; |
| |
| rpmpd_opp_min_svs: opp3 { |
| opp-level = <RPM_SMD_LEVEL_MIN_SVS>; |
| }; |
| |
| rpmpd_opp_low_svs: opp4 { |
| opp-level = <RPM_SMD_LEVEL_LOW_SVS>; |
| }; |
| |
| rpmpd_opp_svs: opp5 { |
| opp-level = <RPM_SMD_LEVEL_SVS>; |
| }; |
| |
| rpmpd_opp_svs_plus: opp6 { |
| opp-level = <RPM_SMD_LEVEL_SVS_PLUS>; |
| }; |
| |
| rpmpd_opp_nom: opp7 { |
| opp-level = <RPM_SMD_LEVEL_NOM>; |
| }; |
| |
| rpmpd_opp_nom_plus: opp8 { |
| opp-level = <RPM_SMD_LEVEL_NOM_PLUS>; |
| }; |
| |
| rpmpd_opp_turbo: opp9 { |
| opp-level = <RPM_SMD_LEVEL_TURBO>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| wlan_msa_guard: wlan-msa-guard@85600000 { |
| reg = <0x0 0x85600000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| wlan_msa_mem: wlan-msa-mem@85700000 { |
| reg = <0x0 0x85700000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| qhee_code: qhee-code@85800000 { |
| reg = <0x0 0x85800000 0x0 0x600000>; |
| no-map; |
| }; |
| |
| rmtfs_mem: memory@85e00000 { |
| compatible = "qcom,rmtfs-mem"; |
| reg = <0x0 0x85e00000 0x0 0x200000>; |
| no-map; |
| |
| qcom,client-id = <1>; |
| qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>; |
| }; |
| |
| smem_region: smem-mem@86000000 { |
| reg = <0 0x86000000 0 0x200000>; |
| no-map; |
| }; |
| |
| tz_mem: memory@86200000 { |
| reg = <0x0 0x86200000 0x0 0x3300000>; |
| no-map; |
| }; |
| |
| mpss_region: mpss@8ac00000 { |
| reg = <0x0 0x8ac00000 0x0 0x7e00000>; |
| no-map; |
| }; |
| |
| adsp_region: adsp@92a00000 { |
| reg = <0x0 0x92a00000 0x0 0x1e00000>; |
| no-map; |
| }; |
| |
| mba_region: mba@94800000 { |
| reg = <0x0 0x94800000 0x0 0x200000>; |
| no-map; |
| }; |
| |
| buffer_mem: tzbuffer@94a00000 { |
| reg = <0x0 0x94a00000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| venus_region: venus@9f800000 { |
| reg = <0x0 0x9f800000 0x0 0x800000>; |
| no-map; |
| }; |
| |
| adsp_mem: adsp-region@f6000000 { |
| reg = <0x0 0xf6000000 0x0 0x800000>; |
| no-map; |
| }; |
| |
| qseecom_mem: qseecom-region@f6800000 { |
| reg = <0x0 0xf6800000 0x0 0x1400000>; |
| no-map; |
| }; |
| |
| zap_shader_region: gpu@fed00000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x0 0xfed00000 0x0 0xa00000>; |
| no-map; |
| }; |
| }; |
| |
| smem: smem { |
| compatible = "qcom,smem"; |
| memory-region = <&smem_region>; |
| hwlocks = <&tcsr_mutex 3>; |
| }; |
| |
| smp2p-adsp { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <443>, <429>; |
| interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&apcs_glb 10>; |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <2>; |
| |
| adsp_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| adsp_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-mpss { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <435>, <428>; |
| interrupts = <GIC_SPI 451 IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&apcs_glb 14>; |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <1>; |
| |
| modem_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| modem_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| soc@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0 0 0xffffffff>; |
| compatible = "simple-bus"; |
| |
| gcc: clock-controller@100000 { |
| compatible = "qcom,gcc-sdm630"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| reg = <0x00100000 0x94000>; |
| |
| clock-names = "xo", "sleep_clk"; |
| clocks = <&xo_board>, |
| <&sleep_clk>; |
| }; |
| |
| rpm_msg_ram: sram@778000 { |
| compatible = "qcom,rpm-msg-ram"; |
| reg = <0x00778000 0x7000>; |
| }; |
| |
| qfprom: qfprom@780000 { |
| compatible = "qcom,sdm630-qfprom", "qcom,qfprom"; |
| reg = <0x00780000 0x621c>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| qusb2_hstx_trim: hstx-trim@240 { |
| reg = <0x243 0x1>; |
| bits = <1 3>; |
| }; |
| |
| gpu_speed_bin: gpu-speed-bin@41a0 { |
| reg = <0x41a2 0x1>; |
| bits = <5 7>; |
| }; |
| }; |
| |
| rng: rng@793000 { |
| compatible = "qcom,prng-ee"; |
| reg = <0x00793000 0x1000>; |
| clocks = <&gcc GCC_PRNG_AHB_CLK>; |
| clock-names = "core"; |
| }; |
| |
| bimc: interconnect@1008000 { |
| compatible = "qcom,sdm660-bimc"; |
| reg = <0x01008000 0x78000>; |
| #interconnect-cells = <1>; |
| }; |
| |
| restart@10ac000 { |
| compatible = "qcom,pshold"; |
| reg = <0x010ac000 0x4>; |
| }; |
| |
| cnoc: interconnect@1500000 { |
| compatible = "qcom,sdm660-cnoc"; |
| reg = <0x01500000 0x10000>; |
| #interconnect-cells = <1>; |
| }; |
| |
| snoc: interconnect@1626000 { |
| compatible = "qcom,sdm660-snoc"; |
| reg = <0x01626000 0x7090>; |
| #interconnect-cells = <1>; |
| }; |
| |
| anoc2_smmu: iommu@16c0000 { |
| compatible = "qcom,sdm630-smmu-v2", "qcom,smmu-v2"; |
| reg = <0x016c0000 0x40000>; |
| #global-interrupts = <2>; |
| #iommu-cells = <1>; |
| |
| interrupts = |
| <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>, |
| |
| <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 374 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_SPI 375 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_SPI 376 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_SPI 377 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_SPI 378 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 463 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 442 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 443 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 444 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 447 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>; |
| |
| status = "disabled"; |
| }; |
| |
| a2noc: interconnect@1704000 { |
| compatible = "qcom,sdm660-a2noc"; |
| reg = <0x01704000 0xc100>; |
| #interconnect-cells = <1>; |
| clock-names = "ipa", |
| "ufs_axi", |
| "aggre2_ufs_axi", |
| "aggre2_usb3_axi", |
| "cfg_noc_usb2_axi"; |
| clocks = <&rpmcc RPM_SMD_IPA_CLK>, |
| <&gcc GCC_UFS_AXI_CLK>, |
| <&gcc GCC_AGGRE2_UFS_AXI_CLK>, |
| <&gcc GCC_AGGRE2_USB3_AXI_CLK>, |
| <&gcc GCC_CFG_NOC_USB2_AXI_CLK>; |
| }; |
| |
| mnoc: interconnect@1745000 { |
| compatible = "qcom,sdm660-mnoc"; |
| reg = <0x01745000 0xa010>; |
| #interconnect-cells = <1>; |
| clock-names = "iface"; |
| clocks = <&mmcc AHB_CLK_SRC>; |
| }; |
| |
| tsens: thermal-sensor@10ae000 { |
| compatible = "qcom,sdm630-tsens", "qcom,tsens-v2"; |
| reg = <0x010ae000 0x1000>, /* TM */ |
| <0x010ad000 0x1000>; /* SROT */ |
| #qcom,sensors = <12>; |
| interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", "critical"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| tcsr_mutex: hwlock@1f40000 { |
| compatible = "qcom,tcsr-mutex"; |
| reg = <0x01f40000 0x20000>; |
| #hwlock-cells = <1>; |
| }; |
| |
| tcsr_regs_1: syscon@1f60000 { |
| compatible = "qcom,sdm630-tcsr", "syscon"; |
| reg = <0x01f60000 0x20000>; |
| }; |
| |
| tlmm: pinctrl@3100000 { |
| compatible = "qcom,sdm630-pinctrl"; |
| reg = <0x03100000 0x400000>, |
| <0x03500000 0x400000>, |
| <0x03900000 0x400000>; |
| reg-names = "south", "center", "north"; |
| interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| gpio-ranges = <&tlmm 0 0 114>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| |
| blsp1_uart1_default: blsp1-uart1-default-state { |
| pins = "gpio0", "gpio1", "gpio2", "gpio3"; |
| function = "blsp_uart1"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp1_uart1_sleep: blsp1-uart1-sleep-state { |
| pins = "gpio0", "gpio1", "gpio2", "gpio3"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp1_uart2_default: blsp1-uart2-default-state { |
| pins = "gpio4", "gpio5"; |
| function = "blsp_uart2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp2_uart1_default: blsp2-uart1-active-state { |
| tx-rts-pins { |
| pins = "gpio16", "gpio19"; |
| function = "blsp_uart5"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| rx-pins { |
| /* |
| * Avoid garbage data while BT module |
| * is powered off or not driving signal |
| */ |
| pins = "gpio17"; |
| function = "blsp_uart5"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| cts-pins { |
| /* Match the pull of the BT module */ |
| pins = "gpio18"; |
| function = "blsp_uart5"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| }; |
| |
| blsp2_uart1_sleep: blsp2-uart1-sleep-state { |
| tx-pins { |
| pins = "gpio16"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| rx-cts-rts-pins { |
| pins = "gpio17", "gpio18", "gpio19"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| i2c1_default: i2c1-default-state { |
| pins = "gpio2", "gpio3"; |
| function = "blsp_i2c1"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c1_sleep: i2c1-sleep-state { |
| pins = "gpio2", "gpio3"; |
| function = "blsp_i2c1"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| i2c2_default: i2c2-default-state { |
| pins = "gpio6", "gpio7"; |
| function = "blsp_i2c2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c2_sleep: i2c2-sleep-state { |
| pins = "gpio6", "gpio7"; |
| function = "blsp_i2c2"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| i2c3_default: i2c3-default-state { |
| pins = "gpio10", "gpio11"; |
| function = "blsp_i2c3"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c3_sleep: i2c3-sleep-state { |
| pins = "gpio10", "gpio11"; |
| function = "blsp_i2c3"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| i2c4_default: i2c4-default-state { |
| pins = "gpio14", "gpio15"; |
| function = "blsp_i2c4"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c4_sleep: i2c4-sleep-state { |
| pins = "gpio14", "gpio15"; |
| function = "blsp_i2c4"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| i2c5_default: i2c5-default-state { |
| pins = "gpio18", "gpio19"; |
| function = "blsp_i2c5"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c5_sleep: i2c5-sleep-state { |
| pins = "gpio18", "gpio19"; |
| function = "blsp_i2c5"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| i2c6_default: i2c6-default-state { |
| pins = "gpio22", "gpio23"; |
| function = "blsp_i2c6"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c6_sleep: i2c6-sleep-state { |
| pins = "gpio22", "gpio23"; |
| function = "blsp_i2c6"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| i2c7_default: i2c7-default-state { |
| pins = "gpio26", "gpio27"; |
| function = "blsp_i2c7"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c7_sleep: i2c7-sleep-state { |
| pins = "gpio26", "gpio27"; |
| function = "blsp_i2c7"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| i2c8_default: i2c8-default-state { |
| pins = "gpio30", "gpio31"; |
| function = "blsp_i2c8_a"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c8_sleep: i2c8-sleep-state { |
| pins = "gpio30", "gpio31"; |
| function = "blsp_i2c8_a"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| cci0_default: cci0-default-state { |
| pins = "gpio36","gpio37"; |
| function = "cci_i2c"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| cci1_default: cci1-default-state { |
| pins = "gpio38","gpio39"; |
| function = "cci_i2c"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| sdc1_state_on: sdc1-on-state { |
| clk-pins { |
| pins = "sdc1_clk"; |
| bias-disable; |
| drive-strength = <16>; |
| }; |
| |
| cmd-pins { |
| pins = "sdc1_cmd"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| data-pins { |
| pins = "sdc1_data"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| rclk-pins { |
| pins = "sdc1_rclk"; |
| bias-pull-down; |
| }; |
| }; |
| |
| sdc1_state_off: sdc1-off-state { |
| clk-pins { |
| pins = "sdc1_clk"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| cmd-pins { |
| pins = "sdc1_cmd"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| data-pins { |
| pins = "sdc1_data"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| rclk-pins { |
| pins = "sdc1_rclk"; |
| bias-pull-down; |
| }; |
| }; |
| |
| sdc2_state_on: sdc2-on-state { |
| clk-pins { |
| pins = "sdc2_clk"; |
| bias-disable; |
| drive-strength = <16>; |
| }; |
| |
| cmd-pins { |
| pins = "sdc2_cmd"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| data-pins { |
| pins = "sdc2_data"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| }; |
| |
| sdc2_state_off: sdc2-off-state { |
| clk-pins { |
| pins = "sdc2_clk"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| cmd-pins { |
| pins = "sdc2_cmd"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| data-pins { |
| pins = "sdc2_data"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| }; |
| |
| remoteproc_mss: remoteproc@4080000 { |
| compatible = "qcom,sdm660-mss-pil"; |
| reg = <0x04080000 0x100>, <0x04180000 0x40>; |
| reg-names = "qdsp6", "rmb"; |
| |
| interrupts-extended = <&intc GIC_SPI 448 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>, |
| <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", |
| "fatal", |
| "ready", |
| "handover", |
| "stop-ack", |
| "shutdown-ack"; |
| |
| clocks = <&gcc GCC_MSS_CFG_AHB_CLK>, |
| <&gcc GCC_BIMC_MSS_Q6_AXI_CLK>, |
| <&gcc GCC_BOOT_ROM_AHB_CLK>, |
| <&gcc GPLL0_OUT_MSSCC>, |
| <&gcc GCC_MSS_SNOC_AXI_CLK>, |
| <&gcc GCC_MSS_MNOC_BIMC_AXI_CLK>, |
| <&rpmcc RPM_SMD_QDSS_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", |
| "bus", |
| "mem", |
| "gpll0_mss", |
| "snoc_axi", |
| "mnoc_axi", |
| "qdss", |
| "xo"; |
| |
| qcom,smem-states = <&modem_smp2p_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| resets = <&gcc GCC_MSS_RESTART>; |
| reset-names = "mss_restart"; |
| |
| qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>; |
| |
| power-domains = <&rpmpd SDM660_VDDCX>, |
| <&rpmpd SDM660_VDDMX>; |
| power-domain-names = "cx", "mx"; |
| |
| memory-region = <&mba_region>, <&mpss_region>; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts = <GIC_SPI 452 IRQ_TYPE_EDGE_RISING>; |
| label = "modem"; |
| qcom,remote-pid = <1>; |
| mboxes = <&apcs_glb 15>; |
| }; |
| }; |
| |
| adreno_gpu: gpu@5000000 { |
| compatible = "qcom,adreno-508.0", "qcom,adreno"; |
| |
| reg = <0x05000000 0x40000>; |
| reg-names = "kgsl_3d0_reg_memory"; |
| |
| interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_GPU_CFG_AHB_CLK>, |
| <&gpucc GPUCC_RBBMTIMER_CLK>, |
| <&gcc GCC_BIMC_GFX_CLK>, |
| <&gcc GCC_GPU_BIMC_GFX_CLK>, |
| <&gpucc GPUCC_RBCPR_CLK>, |
| <&gpucc GPUCC_GFX3D_CLK>; |
| |
| clock-names = "iface", |
| "rbbmtimer", |
| "mem", |
| "mem_iface", |
| "rbcpr", |
| "core"; |
| |
| power-domains = <&rpmpd SDM660_VDDMX>; |
| iommus = <&kgsl_smmu 0>; |
| |
| nvmem-cells = <&gpu_speed_bin>; |
| nvmem-cell-names = "speed_bin"; |
| |
| interconnects = <&bimc MASTER_OXILI &bimc SLAVE_EBI>; |
| interconnect-names = "gfx-mem"; |
| |
| operating-points-v2 = <&gpu_sdm630_opp_table>; |
| #cooling-cells = <2>; |
| |
| status = "disabled"; |
| |
| gpu_sdm630_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| opp-775000000 { |
| opp-hz = /bits/ 64 <775000000>; |
| opp-level = <RPM_SMD_LEVEL_TURBO>; |
| opp-peak-kBps = <5412000>; |
| opp-supported-hw = <0xa2>; |
| }; |
| opp-647000000 { |
| opp-hz = /bits/ 64 <647000000>; |
| opp-level = <RPM_SMD_LEVEL_NOM_PLUS>; |
| opp-peak-kBps = <4068000>; |
| opp-supported-hw = <0xff>; |
| }; |
| opp-588000000 { |
| opp-hz = /bits/ 64 <588000000>; |
| opp-level = <RPM_SMD_LEVEL_NOM>; |
| opp-peak-kBps = <3072000>; |
| opp-supported-hw = <0xff>; |
| }; |
| opp-465000000 { |
| opp-hz = /bits/ 64 <465000000>; |
| opp-level = <RPM_SMD_LEVEL_SVS_PLUS>; |
| opp-peak-kBps = <2724000>; |
| opp-supported-hw = <0xff>; |
| }; |
| opp-370000000 { |
| opp-hz = /bits/ 64 <370000000>; |
| opp-level = <RPM_SMD_LEVEL_SVS>; |
| opp-peak-kBps = <2188000>; |
| opp-supported-hw = <0xff>; |
| }; |
| opp-240000000 { |
| opp-hz = /bits/ 64 <240000000>; |
| opp-level = <RPM_SMD_LEVEL_LOW_SVS>; |
| opp-peak-kBps = <1648000>; |
| opp-supported-hw = <0xff>; |
| }; |
| opp-160000000 { |
| opp-hz = /bits/ 64 <160000000>; |
| opp-level = <RPM_SMD_LEVEL_MIN_SVS>; |
| opp-peak-kBps = <1200000>; |
| opp-supported-hw = <0xff>; |
| }; |
| }; |
| }; |
| |
| kgsl_smmu: iommu@5040000 { |
| compatible = "qcom,sdm630-smmu-v2", |
| "qcom,adreno-smmu", "qcom,smmu-v2"; |
| reg = <0x05040000 0x10000>; |
| |
| /* |
| * GX GDSC parent is CX. We need to bring up CX for SMMU |
| * but we need both up for Adreno. On the other hand, we |
| * need to manage the GX rpmpd domain in the adreno driver. |
| * Enable CX/GX GDSCs here so that we can manage just the GX |
| * RPM Power Domain in the Adreno driver. |
| */ |
| power-domains = <&gpucc GPU_GX_GDSC>; |
| clocks = <&gcc GCC_GPU_CFG_AHB_CLK>, |
| <&gcc GCC_BIMC_GFX_CLK>, |
| <&gcc GCC_GPU_BIMC_GFX_CLK>; |
| clock-names = "iface", |
| "mem", |
| "mem_iface"; |
| #global-interrupts = <2>; |
| #iommu-cells = <1>; |
| |
| interrupts = |
| <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>, |
| |
| <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>; |
| |
| status = "disabled"; |
| }; |
| |
| gpucc: clock-controller@5065000 { |
| compatible = "qcom,gpucc-sdm630"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| reg = <0x05065000 0x9038>; |
| |
| clocks = <&xo_board>, |
| <&gcc GCC_GPU_GPLL0_CLK>, |
| <&gcc GCC_GPU_GPLL0_DIV_CLK>; |
| clock-names = "xo", |
| "gcc_gpu_gpll0_clk", |
| "gcc_gpu_gpll0_div_clk"; |
| status = "disabled"; |
| }; |
| |
| lpass_smmu: iommu@5100000 { |
| compatible = "qcom,sdm630-smmu-v2", "qcom,smmu-v2"; |
| reg = <0x05100000 0x40000>; |
| #iommu-cells = <1>; |
| |
| #global-interrupts = <2>; |
| interrupts = |
| <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>, |
| |
| <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>; |
| |
| status = "disabled"; |
| }; |
| |
| sram@290000 { |
| compatible = "qcom,rpm-stats"; |
| reg = <0x00290000 0x10000>; |
| }; |
| |
| spmi_bus: spmi@800f000 { |
| compatible = "qcom,spmi-pmic-arb"; |
| reg = <0x0800f000 0x1000>, |
| <0x08400000 0x1000000>, |
| <0x09400000 0x1000000>, |
| <0x0a400000 0x220000>, |
| <0x0800a000 0x3000>; |
| reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; |
| interrupt-names = "periph_irq"; |
| interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,ee = <0>; |
| qcom,channel = <0>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| interrupt-controller; |
| #interrupt-cells = <4>; |
| }; |
| |
| usb3: usb@a8f8800 { |
| compatible = "qcom,sdm660-dwc3", "qcom,dwc3"; |
| reg = <0x0a8f8800 0x400>; |
| status = "disabled"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| clocks = <&gcc GCC_CFG_NOC_USB3_AXI_CLK>, |
| <&gcc GCC_USB30_MASTER_CLK>, |
| <&gcc GCC_AGGRE2_USB3_AXI_CLK>, |
| <&gcc GCC_USB30_SLEEP_CLK>, |
| <&gcc GCC_USB30_MOCK_UTMI_CLK>; |
| clock-names = "cfg_noc", |
| "core", |
| "iface", |
| "sleep", |
| "mock_utmi"; |
| |
| assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB30_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, <120000000>; |
| |
| interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "pwr_event", |
| "qusb2_phy", |
| "hs_phy_irq", |
| "ss_phy_irq"; |
| |
| power-domains = <&gcc USB_30_GDSC>; |
| |
| resets = <&gcc GCC_USB_30_BCR>; |
| |
| usb3_dwc3: usb@a800000 { |
| compatible = "snps,dwc3"; |
| reg = <0x0a800000 0xc8d0>; |
| interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; |
| snps,dis_u2_susphy_quirk; |
| snps,dis_enblslpm_quirk; |
| snps,parkmode-disable-ss-quirk; |
| |
| phys = <&qusb2phy0>, <&usb3_qmpphy>; |
| phy-names = "usb2-phy", "usb3-phy"; |
| snps,hird-threshold = /bits/ 8 <0>; |
| }; |
| }; |
| |
| usb3_qmpphy: phy@c010000 { |
| compatible = "qcom,sdm660-qmp-usb3-phy"; |
| reg = <0x0c010000 0x1000>; |
| |
| clocks = <&gcc GCC_USB3_PHY_AUX_CLK>, |
| <&gcc GCC_USB3_CLKREF_CLK>, |
| <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, |
| <&gcc GCC_USB3_PHY_PIPE_CLK>; |
| clock-names = "aux", |
| "ref", |
| "cfg_ahb", |
| "pipe"; |
| clock-output-names = "usb3_phy_pipe_clk_src"; |
| #clock-cells = <0>; |
| #phy-cells = <0>; |
| |
| resets = <&gcc GCC_USB3_PHY_BCR>, |
| <&gcc GCC_USB3PHY_PHY_BCR>; |
| reset-names = "phy", |
| "phy_phy"; |
| |
| qcom,tcsr-reg = <&tcsr_regs_1 0x6b244>; |
| |
| status = "disabled"; |
| }; |
| |
| qusb2phy0: phy@c012000 { |
| compatible = "qcom,sdm660-qusb2-phy"; |
| reg = <0x0c012000 0x180>; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, |
| <&gcc GCC_RX0_USB2_CLKREF_CLK>; |
| clock-names = "cfg_ahb", "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; |
| nvmem-cells = <&qusb2_hstx_trim>; |
| status = "disabled"; |
| }; |
| |
| qusb2phy1: phy@c014000 { |
| compatible = "qcom,sdm660-qusb2-phy"; |
| reg = <0x0c014000 0x180>; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, |
| <&gcc GCC_RX1_USB2_CLKREF_CLK>; |
| clock-names = "cfg_ahb", "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_SEC_BCR>; |
| nvmem-cells = <&qusb2_hstx_trim>; |
| status = "disabled"; |
| }; |
| |
| sdhc_2: mmc@c084000 { |
| compatible = "qcom,sdm630-sdhci", "qcom,sdhci-msm-v5"; |
| reg = <0x0c084000 0x1000>; |
| reg-names = "hc"; |
| |
| interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| |
| bus-width = <4>; |
| |
| clocks = <&gcc GCC_SDCC2_AHB_CLK>, |
| <&gcc GCC_SDCC2_APPS_CLK>, |
| <&xo_board>; |
| clock-names = "iface", "core", "xo"; |
| |
| |
| interconnects = <&a2noc 3 &a2noc 10>, |
| <&gnoc 0 &cnoc 28>; |
| interconnect-names = "sdhc-ddr","cpu-sdhc"; |
| operating-points-v2 = <&sdhc2_opp_table>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_state_on>; |
| pinctrl-1 = <&sdc2_state_off>; |
| power-domains = <&rpmpd SDM660_VDDCX>; |
| |
| status = "disabled"; |
| |
| sdhc2_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-50000000 { |
| opp-hz = /bits/ 64 <50000000>; |
| required-opps = <&rpmpd_opp_low_svs>; |
| opp-peak-kBps = <200000 140000>; |
| opp-avg-kBps = <130718 133320>; |
| }; |
| opp-100000000 { |
| opp-hz = /bits/ 64 <100000000>; |
| required-opps = <&rpmpd_opp_svs>; |
| opp-peak-kBps = <250000 160000>; |
| opp-avg-kBps = <196078 150000>; |
| }; |
| opp-200000000 { |
| opp-hz = /bits/ 64 <200000000>; |
| required-opps = <&rpmpd_opp_nom>; |
| opp-peak-kBps = <4096000 4096000>; |
| opp-avg-kBps = <1338562 1338562>; |
| }; |
| }; |
| }; |
| |
| sdhc_1: mmc@c0c4000 { |
| compatible = "qcom,sdm630-sdhci", "qcom,sdhci-msm-v5"; |
| reg = <0x0c0c4000 0x1000>, |
| <0x0c0c5000 0x1000>, |
| <0x0c0c8000 0x8000>; |
| reg-names = "hc", "cqhci", "ice"; |
| |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| |
| clocks = <&gcc GCC_SDCC1_AHB_CLK>, |
| <&gcc GCC_SDCC1_APPS_CLK>, |
| <&xo_board>, |
| <&gcc GCC_SDCC1_ICE_CORE_CLK>; |
| clock-names = "iface", "core", "xo", "ice"; |
| |
| interconnects = <&a2noc 2 &a2noc 10>, |
| <&gnoc 0 &cnoc 27>; |
| interconnect-names = "sdhc-ddr", "cpu-sdhc"; |
| operating-points-v2 = <&sdhc1_opp_table>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc1_state_on>; |
| pinctrl-1 = <&sdc1_state_off>; |
| power-domains = <&rpmpd SDM660_VDDCX>; |
| |
| bus-width = <8>; |
| non-removable; |
| |
| status = "disabled"; |
| |
| sdhc1_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-50000000 { |
| opp-hz = /bits/ 64 <50000000>; |
| required-opps = <&rpmpd_opp_low_svs>; |
| opp-peak-kBps = <200000 140000>; |
| opp-avg-kBps = <130718 133320>; |
| }; |
| opp-100000000 { |
| opp-hz = /bits/ 64 <100000000>; |
| required-opps = <&rpmpd_opp_svs>; |
| opp-peak-kBps = <250000 160000>; |
| opp-avg-kBps = <196078 150000>; |
| }; |
| opp-384000000 { |
| opp-hz = /bits/ 64 <384000000>; |
| required-opps = <&rpmpd_opp_nom>; |
| opp-peak-kBps = <4096000 4096000>; |
| opp-avg-kBps = <1338562 1338562>; |
| }; |
| }; |
| }; |
| |
| usb2: usb@c2f8800 { |
| compatible = "qcom,sdm660-dwc3", "qcom,dwc3"; |
| reg = <0x0c2f8800 0x400>; |
| status = "disabled"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| clocks = <&gcc GCC_CFG_NOC_USB2_AXI_CLK>, |
| <&gcc GCC_USB20_MASTER_CLK>, |
| <&gcc GCC_USB20_SLEEP_CLK>, |
| <&gcc GCC_USB20_MOCK_UTMI_CLK>; |
| clock-names = "cfg_noc", "core", |
| "sleep", "mock_utmi"; |
| |
| assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB20_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, <60000000>; |
| |
| interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "pwr_event", |
| "qusb2_phy", |
| "hs_phy_irq"; |
| |
| qcom,select-utmi-as-pipe-clk; |
| |
| resets = <&gcc GCC_USB_20_BCR>; |
| |
| usb2_dwc3: usb@c200000 { |
| compatible = "snps,dwc3"; |
| reg = <0x0c200000 0xc8d0>; |
| interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; |
| snps,dis_u2_susphy_quirk; |
| snps,dis_enblslpm_quirk; |
| |
| /* This is the HS-only host */ |
| maximum-speed = "high-speed"; |
| phys = <&qusb2phy1>; |
| phy-names = "usb2-phy"; |
| snps,hird-threshold = /bits/ 8 <0>; |
| }; |
| }; |
| |
| mmcc: clock-controller@c8c0000 { |
| compatible = "qcom,mmcc-sdm630"; |
| reg = <0x0c8c0000 0x40000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| clock-names = "xo", |
| "sleep_clk", |
| "gpll0", |
| "gpll0_div", |
| "dsi0pll", |
| "dsi0pllbyte", |
| "dsi1pll", |
| "dsi1pllbyte", |
| "dp_link_2x_clk_divsel_five", |
| "dp_vco_divided_clk_src_mux"; |
| clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, |
| <&sleep_clk>, |
| <&gcc GCC_MMSS_GPLL0_CLK>, |
| <&gcc GCC_MMSS_GPLL0_DIV_CLK>, |
| <&mdss_dsi0_phy 1>, |
| <&mdss_dsi0_phy 0>, |
| <0>, |
| <0>, |
| <0>, |
| <0>; |
| }; |
| |
| mdss: display-subsystem@c900000 { |
| compatible = "qcom,mdss"; |
| reg = <0x0c900000 0x1000>, |
| <0x0c9b0000 0x1040>; |
| reg-names = "mdss_phys", "vbif_phys"; |
| |
| power-domains = <&mmcc MDSS_GDSC>; |
| |
| clocks = <&mmcc MDSS_AHB_CLK>, |
| <&mmcc MDSS_AXI_CLK>, |
| <&mmcc MDSS_VSYNC_CLK>, |
| <&mmcc MDSS_MDP_CLK>; |
| clock-names = "iface", |
| "bus", |
| "vsync", |
| "core"; |
| |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| status = "disabled"; |
| |
| mdp: display-controller@c901000 { |
| compatible = "qcom,sdm630-mdp5", "qcom,mdp5"; |
| reg = <0x0c901000 0x89000>; |
| reg-names = "mdp_phys"; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <0>; |
| |
| assigned-clocks = <&mmcc MDSS_MDP_CLK>, |
| <&mmcc MDSS_VSYNC_CLK>; |
| assigned-clock-rates = <300000000>, |
| <19200000>; |
| clocks = <&mmcc MDSS_AHB_CLK>, |
| <&mmcc MDSS_AXI_CLK>, |
| <&mmcc MDSS_MDP_CLK>, |
| <&mmcc MDSS_VSYNC_CLK>; |
| clock-names = "iface", |
| "bus", |
| "core", |
| "vsync"; |
| |
| interconnects = <&mnoc 2 &bimc 5>, |
| <&mnoc 3 &bimc 5>, |
| <&gnoc 0 &mnoc 17>; |
| interconnect-names = "mdp0-mem", |
| "mdp1-mem", |
| "rotator-mem"; |
| iommus = <&mmss_smmu 0>; |
| operating-points-v2 = <&mdp_opp_table>; |
| power-domains = <&rpmpd SDM660_VDDCX>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| mdp5_intf1_out: endpoint { |
| remote-endpoint = <&mdss_dsi0_in>; |
| }; |
| }; |
| }; |
| |
| mdp_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-150000000 { |
| opp-hz = /bits/ 64 <150000000>; |
| opp-peak-kBps = <320000 320000 76800>; |
| required-opps = <&rpmpd_opp_low_svs>; |
| }; |
| opp-275000000 { |
| opp-hz = /bits/ 64 <275000000>; |
| opp-peak-kBps = <6400000 6400000 160000>; |
| required-opps = <&rpmpd_opp_svs>; |
| }; |
| opp-300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| opp-peak-kBps = <6400000 6400000 190000>; |
| required-opps = <&rpmpd_opp_svs_plus>; |
| }; |
| opp-330000000 { |
| opp-hz = /bits/ 64 <330000000>; |
| opp-peak-kBps = <6400000 6400000 240000>; |
| required-opps = <&rpmpd_opp_nom>; |
| }; |
| opp-412500000 { |
| opp-hz = /bits/ 64 <412500000>; |
| opp-peak-kBps = <6400000 6400000 320000>; |
| required-opps = <&rpmpd_opp_turbo>; |
| }; |
| }; |
| }; |
| |
| mdss_dsi0: dsi@c994000 { |
| compatible = "qcom,sdm660-dsi-ctrl", |
| "qcom,mdss-dsi-ctrl"; |
| reg = <0x0c994000 0x400>; |
| reg-names = "dsi_ctrl"; |
| |
| operating-points-v2 = <&dsi_opp_table>; |
| power-domains = <&rpmpd SDM660_VDDCX>; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <4>; |
| |
| assigned-clocks = <&mmcc BYTE0_CLK_SRC>, |
| <&mmcc PCLK0_CLK_SRC>; |
| assigned-clock-parents = <&mdss_dsi0_phy 0>, |
| <&mdss_dsi0_phy 1>; |
| |
| clocks = <&mmcc MDSS_MDP_CLK>, |
| <&mmcc MDSS_BYTE0_CLK>, |
| <&mmcc MDSS_BYTE0_INTF_CLK>, |
| <&mmcc MNOC_AHB_CLK>, |
| <&mmcc MDSS_AHB_CLK>, |
| <&mmcc MDSS_AXI_CLK>, |
| <&mmcc MISC_AHB_CLK>, |
| <&mmcc MDSS_PCLK0_CLK>, |
| <&mmcc MDSS_ESC0_CLK>; |
| clock-names = "mdp_core", |
| "byte", |
| "byte_intf", |
| "mnoc", |
| "iface", |
| "bus", |
| "core_mmss", |
| "pixel", |
| "core"; |
| |
| phys = <&mdss_dsi0_phy>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| mdss_dsi0_in: endpoint { |
| remote-endpoint = <&mdp5_intf1_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| mdss_dsi0_out: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| mdss_dsi0_phy: phy@c994400 { |
| compatible = "qcom,dsi-phy-14nm-660"; |
| reg = <0x0c994400 0x100>, |
| <0x0c994500 0x300>, |
| <0x0c994800 0x188>; |
| reg-names = "dsi_phy", |
| "dsi_phy_lane", |
| "dsi_pll"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>; |
| clock-names = "iface", "ref"; |
| status = "disabled"; |
| }; |
| }; |
| |
| blsp1_dma: dma-controller@c144000 { |
| compatible = "qcom,bam-v1.7.0"; |
| reg = <0x0c144000 0x1f000>; |
| interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| qcom,controlled-remotely; |
| num-channels = <18>; |
| qcom,num-ees = <4>; |
| }; |
| |
| blsp1_uart1: serial@c16f000 { |
| compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; |
| reg = <0x0c16f000 0x200>; |
| interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| dmas = <&blsp1_dma 0>, <&blsp1_dma 1>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp1_uart1_default>; |
| pinctrl-1 = <&blsp1_uart1_sleep>; |
| status = "disabled"; |
| }; |
| |
| blsp1_uart2: serial@c170000 { |
| compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; |
| reg = <0x0c170000 0x1000>; |
| interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| dmas = <&blsp1_dma 2>, <&blsp1_dma 3>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&blsp1_uart2_default>; |
| status = "disabled"; |
| }; |
| |
| blsp_i2c1: i2c@c175000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x0c175000 0x600>; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp1_dma 4>, <&blsp1_dma 5>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c1_default>; |
| pinctrl-1 = <&i2c1_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| blsp_i2c2: i2c@c176000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x0c176000 0x600>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp1_dma 6>, <&blsp1_dma 7>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c2_default>; |
| pinctrl-1 = <&i2c2_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| blsp_i2c3: i2c@c177000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x0c177000 0x600>; |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp1_dma 8>, <&blsp1_dma 9>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c3_default>; |
| pinctrl-1 = <&i2c3_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| blsp_i2c4: i2c@c178000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x0c178000 0x600>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp1_dma 10>, <&blsp1_dma 11>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c4_default>; |
| pinctrl-1 = <&i2c4_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| blsp2_dma: dma-controller@c184000 { |
| compatible = "qcom,bam-v1.7.0"; |
| reg = <0x0c184000 0x1f000>; |
| interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| qcom,controlled-remotely; |
| num-channels = <18>; |
| qcom,num-ees = <4>; |
| }; |
| |
| blsp2_uart1: serial@c1af000 { |
| compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; |
| reg = <0x0c1af000 0x200>; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP2_UART1_APPS_CLK>, |
| <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "core", "iface"; |
| dmas = <&blsp2_dma 0>, <&blsp2_dma 1>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp2_uart1_default>; |
| pinctrl-1 = <&blsp2_uart1_sleep>; |
| status = "disabled"; |
| }; |
| |
| blsp_i2c5: i2c@c1b5000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x0c1b5000 0x600>; |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp2_dma 4>, <&blsp2_dma 5>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c5_default>; |
| pinctrl-1 = <&i2c5_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| blsp_i2c6: i2c@c1b6000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x0c1b6000 0x600>; |
| interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp2_dma 6>, <&blsp2_dma 7>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c6_default>; |
| pinctrl-1 = <&i2c6_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| blsp_i2c7: i2c@c1b7000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x0c1b7000 0x600>; |
| interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp2_dma 8>, <&blsp2_dma 9>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c7_default>; |
| pinctrl-1 = <&i2c7_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| blsp_i2c8: i2c@c1b8000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x0c1b8000 0x600>; |
| interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp2_dma 10>, <&blsp2_dma 11>; |
| dma-names = "tx", "rx"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&i2c8_default>; |
| pinctrl-1 = <&i2c8_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| sram@146bf000 { |
| compatible = "qcom,sdm630-imem", "syscon", "simple-mfd"; |
| reg = <0x146bf000 0x1000>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| ranges = <0 0x146bf000 0x1000>; |
| |
| pil-reloc@94c { |
| compatible = "qcom,pil-reloc-info"; |
| reg = <0x94c 0xc8>; |
| }; |
| }; |
| |
| camss: camss@ca00020 { |
| compatible = "qcom,sdm660-camss"; |
| reg = <0x0ca00020 0x10>, |
| <0x0ca30000 0x100>, |
| <0x0ca30400 0x100>, |
| <0x0ca30800 0x100>, |
| <0x0ca30c00 0x100>, |
| <0x0c824000 0x1000>, |
| <0x0ca00120 0x4>, |
| <0x0c825000 0x1000>, |
| <0x0ca00124 0x4>, |
| <0x0c826000 0x1000>, |
| <0x0ca00128 0x4>, |
| <0x0ca31000 0x500>, |
| <0x0ca10000 0x1000>, |
| <0x0ca14000 0x1000>; |
| reg-names = "csi_clk_mux", |
| "csid0", |
| "csid1", |
| "csid2", |
| "csid3", |
| "csiphy0", |
| "csiphy0_clk_mux", |
| "csiphy1", |
| "csiphy1_clk_mux", |
| "csiphy2", |
| "csiphy2_clk_mux", |
| "ispif", |
| "vfe0", |
| "vfe1"; |
| interrupts = <GIC_SPI 296 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 297 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 298 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 299 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 80 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 309 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 314 IRQ_TYPE_EDGE_RISING>, |
| <GIC_SPI 315 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "csid0", |
| "csid1", |
| "csid2", |
| "csid3", |
| "csiphy0", |
| "csiphy1", |
| "csiphy2", |
| "ispif", |
| "vfe0", |
| "vfe1"; |
| clocks = <&mmcc CAMSS_AHB_CLK>, |
| <&mmcc CAMSS_CPHY_CSID0_CLK>, |
| <&mmcc CAMSS_CPHY_CSID1_CLK>, |
| <&mmcc CAMSS_CPHY_CSID2_CLK>, |
| <&mmcc CAMSS_CPHY_CSID3_CLK>, |
| <&mmcc CAMSS_CSI0_AHB_CLK>, |
| <&mmcc CAMSS_CSI0_CLK>, |
| <&mmcc CAMSS_CPHY_CSID0_CLK>, |
| <&mmcc CAMSS_CSI0PIX_CLK>, |
| <&mmcc CAMSS_CSI0RDI_CLK>, |
| <&mmcc CAMSS_CSI1_AHB_CLK>, |
| <&mmcc CAMSS_CSI1_CLK>, |
| <&mmcc CAMSS_CPHY_CSID1_CLK>, |
| <&mmcc CAMSS_CSI1PIX_CLK>, |
| <&mmcc CAMSS_CSI1RDI_CLK>, |
| <&mmcc CAMSS_CSI2_AHB_CLK>, |
| <&mmcc CAMSS_CSI2_CLK>, |
| <&mmcc CAMSS_CPHY_CSID2_CLK>, |
| <&mmcc CAMSS_CSI2PIX_CLK>, |
| <&mmcc CAMSS_CSI2RDI_CLK>, |
| <&mmcc CAMSS_CSI3_AHB_CLK>, |
| <&mmcc CAMSS_CSI3_CLK>, |
| <&mmcc CAMSS_CPHY_CSID3_CLK>, |
| <&mmcc CAMSS_CSI3PIX_CLK>, |
| <&mmcc CAMSS_CSI3RDI_CLK>, |
| <&mmcc CAMSS_CSI0PHYTIMER_CLK>, |
| <&mmcc CAMSS_CSI1PHYTIMER_CLK>, |
| <&mmcc CAMSS_CSI2PHYTIMER_CLK>, |
| <&mmcc CSIPHY_AHB2CRIF_CLK>, |
| <&mmcc CAMSS_CSI_VFE0_CLK>, |
| <&mmcc CAMSS_CSI_VFE1_CLK>, |
| <&mmcc CAMSS_ISPIF_AHB_CLK>, |
| <&mmcc THROTTLE_CAMSS_AXI_CLK>, |
| <&mmcc CAMSS_TOP_AHB_CLK>, |
| <&mmcc CAMSS_VFE0_AHB_CLK>, |
| <&mmcc CAMSS_VFE0_CLK>, |
| <&mmcc CAMSS_VFE0_STREAM_CLK>, |
| <&mmcc CAMSS_VFE1_AHB_CLK>, |
| <&mmcc CAMSS_VFE1_CLK>, |
| <&mmcc CAMSS_VFE1_STREAM_CLK>, |
| <&mmcc CAMSS_VFE_VBIF_AHB_CLK>, |
| <&mmcc CAMSS_VFE_VBIF_AXI_CLK>; |
| clock-names = "ahb", |
| "cphy_csid0", |
| "cphy_csid1", |
| "cphy_csid2", |
| "cphy_csid3", |
| "csi0_ahb", |
| "csi0", |
| "csi0_phy", |
| "csi0_pix", |
| "csi0_rdi", |
| "csi1_ahb", |
| "csi1", |
| "csi1_phy", |
| "csi1_pix", |
| "csi1_rdi", |
| "csi2_ahb", |
| "csi2", |
| "csi2_phy", |
| "csi2_pix", |
| "csi2_rdi", |
| "csi3_ahb", |
| "csi3", |
| "csi3_phy", |
| "csi3_pix", |
| "csi3_rdi", |
| "csiphy0_timer", |
| "csiphy1_timer", |
| "csiphy2_timer", |
| "csiphy_ahb2crif", |
| "csi_vfe0", |
| "csi_vfe1", |
| "ispif_ahb", |
| "throttle_axi", |
| "top_ahb", |
| "vfe0_ahb", |
| "vfe0", |
| "vfe0_stream", |
| "vfe1_ahb", |
| "vfe1", |
| "vfe1_stream", |
| "vfe_ahb", |
| "vfe_axi"; |
| interconnects = <&mnoc 5 &bimc 5>; |
| interconnect-names = "vfe-mem"; |
| iommus = <&mmss_smmu 0xc00>, |
| <&mmss_smmu 0xc01>, |
| <&mmss_smmu 0xc02>, |
| <&mmss_smmu 0xc03>; |
| power-domains = <&mmcc CAMSS_VFE0_GDSC>, |
| <&mmcc CAMSS_VFE1_GDSC>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| cci: cci@ca0c000 { |
| compatible = "qcom,msm8996-cci"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0ca0c000 0x1000>; |
| interrupts = <GIC_SPI 295 IRQ_TYPE_EDGE_RISING>; |
| |
| assigned-clocks = <&mmcc CAMSS_CCI_AHB_CLK>, |
| <&mmcc CAMSS_CCI_CLK>; |
| assigned-clock-rates = <80800000>, <37500000>; |
| clocks = <&mmcc CAMSS_TOP_AHB_CLK>, |
| <&mmcc CAMSS_CCI_AHB_CLK>, |
| <&mmcc CAMSS_CCI_CLK>, |
| <&mmcc CAMSS_AHB_CLK>; |
| clock-names = "camss_top_ahb", |
| "cci_ahb", |
| "cci", |
| "camss_ahb"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&cci0_default &cci1_default>; |
| power-domains = <&mmcc CAMSS_TOP_GDSC>; |
| status = "disabled"; |
| |
| cci_i2c0: i2c-bus@0 { |
| reg = <0>; |
| clock-frequency = <400000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| cci_i2c1: i2c-bus@1 { |
| reg = <1>; |
| clock-frequency = <400000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| venus: video-codec@cc00000 { |
| compatible = "qcom,sdm660-venus"; |
| reg = <0x0cc00000 0xff000>; |
| clocks = <&mmcc VIDEO_CORE_CLK>, |
| <&mmcc VIDEO_AHB_CLK>, |
| <&mmcc VIDEO_AXI_CLK>, |
| <&mmcc THROTTLE_VIDEO_AXI_CLK>; |
| clock-names = "core", "iface", "bus", "bus_throttle"; |
| interconnects = <&gnoc 0 &mnoc 13>, |
| <&mnoc 4 &bimc 5>; |
| interconnect-names = "cpu-cfg", "video-mem"; |
| interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>; |
| iommus = <&mmss_smmu 0x400>, |
| <&mmss_smmu 0x401>, |
| <&mmss_smmu 0x40a>, |
| <&mmss_smmu 0x407>, |
| <&mmss_smmu 0x40e>, |
| <&mmss_smmu 0x40f>, |
| <&mmss_smmu 0x408>, |
| <&mmss_smmu 0x409>, |
| <&mmss_smmu 0x40b>, |
| <&mmss_smmu 0x40c>, |
| <&mmss_smmu 0x40d>, |
| <&mmss_smmu 0x410>, |
| <&mmss_smmu 0x421>, |
| <&mmss_smmu 0x428>, |
| <&mmss_smmu 0x429>, |
| <&mmss_smmu 0x42b>, |
| <&mmss_smmu 0x42c>, |
| <&mmss_smmu 0x42d>, |
| <&mmss_smmu 0x411>, |
| <&mmss_smmu 0x431>; |
| memory-region = <&venus_region>; |
| power-domains = <&mmcc VENUS_GDSC>; |
| status = "disabled"; |
| |
| video-decoder { |
| compatible = "venus-decoder"; |
| clocks = <&mmcc VIDEO_SUBCORE0_CLK>; |
| clock-names = "vcodec0_core"; |
| power-domains = <&mmcc VENUS_CORE0_GDSC>; |
| }; |
| |
| video-encoder { |
| compatible = "venus-encoder"; |
| clocks = <&mmcc VIDEO_SUBCORE0_CLK>; |
| clock-names = "vcodec0_core"; |
| power-domains = <&mmcc VENUS_CORE0_GDSC>; |
| }; |
| }; |
| |
| mmss_smmu: iommu@cd00000 { |
| compatible = "qcom,sdm630-smmu-v2", "qcom,smmu-v2"; |
| reg = <0x0cd00000 0x40000>; |
| |
| clocks = <&mmcc MNOC_AHB_CLK>, |
| <&mmcc BIMC_SMMU_AHB_CLK>, |
| <&mmcc BIMC_SMMU_AXI_CLK>; |
| clock-names = "iface-mm", "iface-smmu", |
| "bus-smmu"; |
| #global-interrupts = <2>; |
| #iommu-cells = <1>; |
| |
| interrupts = |
| <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>, |
| |
| <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 276 IRQ_TYPE_LEVEL_HIGH>; |
| |
| status = "disabled"; |
| }; |
| |
| adsp_pil: remoteproc@15700000 { |
| compatible = "qcom,sdm660-adsp-pas"; |
| reg = <0x15700000 0x4040>; |
| |
| interrupts-extended = |
| <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| |
| clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "xo"; |
| |
| memory-region = <&adsp_region>; |
| power-domains = <&rpmpd SDM660_VDDCX>; |
| power-domain-names = "cx"; |
| |
| qcom,smem-states = <&adsp_smp2p_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| glink-edge { |
| interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>; |
| |
| label = "lpass"; |
| mboxes = <&apcs_glb 9>; |
| qcom,remote-pid = <2>; |
| |
| apr { |
| compatible = "qcom,apr-v2"; |
| qcom,glink-channels = "apr_audio_svc"; |
| qcom,domain = <APR_DOMAIN_ADSP>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| service@3 { |
| reg = <APR_SVC_ADSP_CORE>; |
| compatible = "qcom,q6core"; |
| }; |
| |
| q6afe: service@4 { |
| compatible = "qcom,q6afe"; |
| reg = <APR_SVC_AFE>; |
| q6afedai: dais { |
| compatible = "qcom,q6afe-dais"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #sound-dai-cells = <1>; |
| }; |
| }; |
| |
| q6asm: service@7 { |
| compatible = "qcom,q6asm"; |
| reg = <APR_SVC_ASM>; |
| q6asmdai: dais { |
| compatible = "qcom,q6asm-dais"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #sound-dai-cells = <1>; |
| iommus = <&lpass_smmu 1>; |
| }; |
| }; |
| |
| q6adm: service@8 { |
| compatible = "qcom,q6adm"; |
| reg = <APR_SVC_ADM>; |
| q6routing: routing { |
| compatible = "qcom,q6adm-routing"; |
| #sound-dai-cells = <0>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| gnoc: interconnect@17900000 { |
| compatible = "qcom,sdm660-gnoc"; |
| reg = <0x17900000 0xe000>; |
| #interconnect-cells = <1>; |
| }; |
| |
| apcs_glb: mailbox@17911000 { |
| compatible = "qcom,sdm660-apcs-hmss-global", |
| "qcom,msm8994-apcs-kpss-global"; |
| reg = <0x17911000 0x1000>; |
| |
| #mbox-cells = <1>; |
| }; |
| |
| timer@17920000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| compatible = "arm,armv7-timer-mem"; |
| reg = <0x17920000 0x1000>; |
| clock-frequency = <19200000>; |
| |
| frame@17921000 { |
| frame-number = <0>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17921000 0x1000>, |
| <0x17922000 0x1000>; |
| }; |
| |
| frame@17923000 { |
| frame-number = <1>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17923000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17924000 { |
| frame-number = <2>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17924000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17925000 { |
| frame-number = <3>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17925000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17926000 { |
| frame-number = <4>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17926000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17927000 { |
| frame-number = <5>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17927000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17928000 { |
| frame-number = <6>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x17928000 0x1000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| intc: interrupt-controller@17a00000 { |
| compatible = "arm,gic-v3"; |
| reg = <0x17a00000 0x10000>, /* GICD */ |
| <0x17b00000 0x100000>; /* GICR * 8 */ |
| #interrupt-cells = <3>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| interrupt-controller; |
| #redistributor-regions = <1>; |
| redistributor-stride = <0x0 0x20000>; |
| interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| sound: sound { |
| }; |
| |
| thermal-zones { |
| aoss-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 0>; |
| |
| trips { |
| aoss_alert0: trip-point0 { |
| temperature = <105000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| cpuss0-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 1>; |
| |
| trips { |
| cpuss0_alert0: trip-point0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| cpuss1-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 2>; |
| |
| trips { |
| cpuss1_alert0: trip-point0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| cpu0-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 3>; |
| |
| trips { |
| cpu0_alert0: trip-point0 { |
| temperature = <70000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| cpu0_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu1-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 4>; |
| |
| trips { |
| cpu1_alert0: trip-point0 { |
| temperature = <70000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| cpu1_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu2-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 5>; |
| |
| trips { |
| cpu2_alert0: trip-point0 { |
| temperature = <70000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| cpu2_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu3-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 6>; |
| |
| trips { |
| cpu3_alert0: trip-point0 { |
| temperature = <70000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| cpu3_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| /* |
| * According to what downstream DTS says, |
| * the entire power efficient cluster has |
| * only a single thermal sensor. |
| */ |
| |
| pwr-cluster-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 7>; |
| |
| trips { |
| pwr_cluster_alert0: trip-point0 { |
| temperature = <70000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| pwr_cluster_crit: cpu-crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpu-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 8>; |
| |
| cooling-maps { |
| map0 { |
| trip = <&gpu_alert0>; |
| cooling-device = <&adreno_gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| |
| trips { |
| gpu_alert0: trip-point0 { |
| temperature = <85000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <90000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| |
| trip-point2 { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; |
| }; |
| }; |
| |
