| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved. |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include "sdx75.dtsi" |
| #include "pm7550ba.dtsi" |
| #include "pmk8550.dtsi" |
| #include "pmx75.dtsi" |
| |
| / { |
| model = "Qualcomm Technologies, Inc. SDX75 IDP"; |
| compatible = "qcom,sdx75-idp", "qcom,sdx75"; |
| |
| aliases { |
| serial0 = &uart1; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| }; |
| |
| vph_ext: vph-ext-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_ext"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| }; |
| |
| vreg_bob_3p3: pmx75-bob { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_bob_3p3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| vin-supply = <&vph_ext>; |
| }; |
| |
| reg_2v952_vcc: regulator-2v952-vcc { |
| compatible = "regulator-gpio"; |
| regulator-name = "2v952_vcc"; |
| regulator-min-microvolt = <1650000>; |
| regulator-max-microvolt = <3600000>; |
| enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>; |
| gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>; |
| states = <1650000 0>, <3600000 1>; |
| startup-delay-us = <5000>; |
| enable-active-high; |
| regulator-boot-on; |
| |
| vin-supply = <&vph_ext>; |
| }; |
| |
| reg_2v95_vdd: regulator-2v95-vdd { |
| compatible = "regulator-fixed"; |
| regulator-name = "2v95_vdd"; |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| vin-supply = <®_2v952_vcc>; |
| }; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pmx75-rpmh-regulators"; |
| qcom,pmic-id = "b"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| vdd-s7-supply = <&vph_pwr>; |
| vdd-s8-supply = <&vph_pwr>; |
| vdd-s9-supply = <&vph_pwr>; |
| vdd-s10-supply = <&vph_pwr>; |
| vdd-l1-supply = <&vreg_s2b_1p224>; |
| vdd-l2-l18-supply = <&vreg_s2b_1p224>; |
| vdd-l3-supply = <&vreg_s7b_0p936>; |
| vdd-l4-l16-supply = <&vreg_s7b_0p936>; |
| vdd-l5-l6-supply = <&vreg_s4b_1p824>; |
| vdd-l7-supply = <&vreg_s7b_0p936>; |
| vdd-l8-l9-supply = <&vreg_s8b_0p824>; |
| vdd-l10-supply = <&vreg_bob_3p3>; |
| vdd-l11-l13-supply = <&vreg_bob_3p3>; |
| vdd-l12-supply = <&vreg_s2b_1p224>; |
| vdd-l14-supply = <&vreg_s3b_0p752>; |
| vdd-l15-supply = <&vreg_s2b_1p224>; |
| vdd-l17-supply = <&vreg_s8b_0p824>; |
| vdd-l19-supply = <&vreg_s7b_0p936>; |
| vdd-l20-l21-supply = <&vreg_s7b_0p936>; |
| |
| vreg_s2b_1p224: smps2 { |
| regulator-name = "vreg_s2b_1p224"; |
| regulator-min-microvolt = <1224000>; |
| regulator-max-microvolt = <1350000>; |
| }; |
| |
| vreg_s3b_0p752: smps3 { |
| regulator-name = "vreg_s3b_0p752"; |
| regulator-min-microvolt = <684000>; |
| regulator-max-microvolt = <904000>; |
| }; |
| |
| vreg_s4b_1p824: smps4 { |
| regulator-name = "vreg_s4b_1p824"; |
| regulator-min-microvolt = <1824000>; |
| regulator-max-microvolt = <1904000>; |
| }; |
| |
| vreg_s7b_0p936: smps7 { |
| regulator-name = "vreg_s7b_0p936"; |
| regulator-min-microvolt = <352000>; |
| regulator-max-microvolt = <1060000>; |
| }; |
| |
| vreg_s8b_0p824: smps8 { |
| regulator-name = "vreg_s8b_0p824"; |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1100000>; |
| }; |
| |
| vreg_l1b_1p2: ldo1 { |
| regulator-name = "vreg_l1b_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2b_1p128: ldo2 { |
| regulator-name = "vreg_l2b_1p128"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1160000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3b_0p896: ldo3 { |
| regulator-name = "vreg_l3b_0p896"; |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1040000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4b_0p88: ldo4 { |
| regulator-name = "vreg_l4b_0p88"; |
| regulator-min-microvolt = <864000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5b_1p776: ldo5 { |
| regulator-name = "vreg_l5b_1p776"; |
| regulator-min-microvolt = <1770000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6b_1p8: ldo6 { |
| regulator-name = "vreg_l6b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7b_0p904: ldo7 { |
| regulator-name = "vreg_l7b_0p904"; |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8b_0p8: ldo8 { |
| regulator-name = "vreg_l8b_0p8"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9b_0p752: ldo9 { |
| regulator-name = "vreg_l9b_0p752"; |
| regulator-min-microvolt = <752000>; |
| regulator-max-microvolt = <800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10b_3p08: ldo10 { |
| regulator-name = "vreg_l10b_3p08"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3088000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l11b_1p8: ldo11 { |
| regulator-name = "vreg_l11b_1p8"; |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <2928000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12b_1p2: ldo12 { |
| regulator-name = "vreg_l12b_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13b_1p8: ldo13 { |
| regulator-name = "vreg_l13b_1p8"; |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <2928000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14b_0p624: ldo14 { |
| regulator-name = "vreg_l14b_0p624"; |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l15b_1p2: ldo15 { |
| regulator-name = "vreg_l15b_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l16b_0p912: ldo16 { |
| regulator-name = "vreg_l16b_0p912"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l17b_0p752: ldo17 { |
| regulator-name = "vreg_l17b_0p752"; |
| regulator-min-microvolt = <684000>; |
| regulator-max-microvolt = <957600>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l19b_0p952: ldo19 { |
| regulator-name = "vreg_l19b_0p952"; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l20b_0p912: ldo20 { |
| regulator-name = "vreg_l20b_0p912"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <952000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l21b_0p856: ldo21 { |
| regulator-name = "vreg_l21b_0p856"; |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| }; |
| |
| &chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| &pm7550ba_eusb2_repeater { |
| vdd18-supply = <&vreg_l5b_1p776>; |
| vdd3-supply = <&vreg_l10b_3p08>; |
| }; |
| |
| &qupv3_id_0 { |
| status = "okay"; |
| }; |
| |
| &remoteproc_mpss { |
| firmware-name = "qcom/sdx75/modem.mbn", |
| "qcom/sdx75/modem_dtb.mbn"; |
| status = "okay"; |
| }; |
| |
| &sdhc { |
| cd-gpios = <&tlmm 103 GPIO_ACTIVE_LOW>; |
| vmmc-supply = <®_2v95_vdd>; |
| vqmmc-supply = <®_2v952_vcc>; |
| bus-width = <4>; |
| no-sdio; |
| no-mmc; |
| |
| pinctrl-0 = <&sdc1_default &sd_cd>; |
| pinctrl-1 = <&sdc1_sleep &sd_cd>; |
| pinctrl-names = "default", "sleep"; |
| |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <110 6>; |
| |
| sd_cd: sd-cd-state { |
| pins = "gpio103"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| &uart1 { |
| status = "okay"; |
| }; |
| |
| &usb { |
| status = "okay"; |
| }; |
| |
| &usb_dwc3 { |
| dr_mode = "peripheral"; |
| }; |
| |
| &usb_hsphy { |
| vdd-supply = <&vreg_l4b_0p88>; |
| vdda12-supply = <&vreg_l1b_1p2>; |
| |
| phys = <&pm7550ba_eusb2_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_qmpphy { |
| vdda-phy-supply = <&vreg_l4b_0p88>; |
| vdda-pll-supply = <&vreg_l1b_1p2>; |
| |
| status = "okay"; |
| }; |
