| // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) |
| /* |
| * Copyright (c) 2023 - 2024, Dang Huynh <danct12@riseup.net> |
| */ |
| |
| /dts-v1/; |
| |
| #include "sm6115.dtsi" |
| #include "pm6125.dtsi" |
| #include "pmi632.dtsi" |
| #include <dt-bindings/arm/qcom,ids.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/usb/pd.h> |
| |
| / { |
| model = "F(x)tec Pro1X (QX1050)"; |
| compatible = "fxtec,pro1x", "qcom,sm6115"; |
| chassis-type = "handset"; |
| |
| qcom,msm-id = <QCOM_ID_SM6115 0x10000>; |
| |
| chosen { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| framebuffer0: framebuffer@5c000000 { |
| compatible = "simple-framebuffer"; |
| reg = <0x0 0x5c000000 0x0 (1080 * 2160 * 4)>; |
| width = <1080>; |
| height = <2160>; |
| stride = <(1080 * 4)>; |
| format = "a8r8g8b8"; |
| clocks = <&gcc GCC_DISP_HF_AXI_CLK>; |
| }; |
| }; |
| |
| disp_elvdd_supply: disp-elvdd-supply { |
| compatible = "regulator-fixed"; |
| regulator-name = "disp_elvdd_supply"; |
| }; |
| |
| disp_elvss_supply: disp-elvss-supply { |
| compatible = "regulator-fixed"; |
| regulator-name = "disp_elvss_supply"; |
| }; |
| |
| disp_vcc_supply: disp-vcc-supply { |
| compatible = "regulator-fixed"; |
| regulator-name = "disp_vcc_supply"; |
| }; |
| |
| disp_vci_supply: disp-vci-supply { |
| compatible = "regulator-fixed"; |
| regulator-name = "disp_vci_supply"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&hall_sensor_n>, <&key_camera_n>, <&vol_up_n>; |
| pinctrl-names = "default"; |
| |
| hall-switch { |
| label = "Hall Switch"; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_KEYPAD_SLIDE>; |
| gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; |
| debounce-interval = <90>; |
| wakeup-source; |
| }; |
| |
| key-camera { |
| label = "Camera Button"; |
| linux,code = <KEY_CAMERA>; |
| gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; |
| debounce-interval = <15>; |
| }; |
| |
| key-volume-up { |
| label = "Volume Up"; |
| linux,code = <KEY_VOLUMEUP>; |
| gpios = <&pm6125_gpios 5 GPIO_ACTIVE_LOW>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| wakeup-source; |
| }; |
| }; |
| |
| gpio-leds { |
| compatible = "gpio-leds"; |
| |
| capslock-led { |
| label = "green:capslock"; |
| function = LED_FUNCTION_CAPSLOCK; |
| color = <LED_COLOR_ID_GREEN>; |
| gpios = <&pca9534 1 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "kbd-capslock"; |
| default-state = "off"; |
| }; |
| }; |
| |
| ts_vdd_supply: ts-vdd-supply { |
| compatible = "regulator-fixed"; |
| regulator-name = "ts_vdd_supply"; |
| gpio = <&pca9534 3 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| ts_vddio_supply: ts-vddio-supply { |
| compatible = "regulator-fixed"; |
| regulator-name = "ts_vddio_supply"; |
| gpio = <&pca9534 2 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| }; |
| |
| &gpi_dma0 { |
| status = "okay"; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| firmware-name = "qcom/sm6115/Fxtec/QX1050/a610_zap.mbn"; |
| }; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <100000>; |
| |
| status = "okay"; |
| |
| pca9534: gpio@21 { |
| compatible = "nxp,pca9534"; |
| reg = <0x21>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| |
| &i2c2 { |
| status = "okay"; |
| /* Clock frequency was not specified downstream, let's park it to 100 KHz */ |
| clock-frequency = <100000>; |
| |
| touchscreen@14 { |
| compatible = "goodix,gt9286"; |
| reg = <0x14>; |
| |
| interrupts-extended = <&tlmm 80 IRQ_TYPE_LEVEL_LOW>; |
| |
| irq-gpios = <&tlmm 80 IRQ_TYPE_LEVEL_LOW>; |
| reset-gpios = <&tlmm 71 GPIO_ACTIVE_HIGH>; |
| AVDD28-supply = <&ts_vdd_supply>; |
| VDDIO-supply = <&ts_vddio_supply>; |
| |
| pinctrl-0 = <&ts_int_n>, <&ts_rst_n>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dsi0 { |
| vdda-supply = <&pm6125_l18a>; |
| status = "okay"; |
| |
| panel: panel@0 { |
| compatible = "boe,bf060y8m-aj0"; |
| reg = <0>; |
| |
| reset-gpios = <&tlmm 82 GPIO_ACTIVE_LOW>; |
| |
| elvdd-supply = <&disp_elvdd_supply>; |
| elvss-supply = <&disp_elvss_supply>; |
| vcc-supply = <&disp_vcc_supply>; |
| vci-supply = <&disp_vci_supply>; |
| vddio-supply = <&pm6125_l9a>; |
| |
| pinctrl-0 = <&mdss_dsi_n &panel_en_n>; |
| pinctrl-names = "default"; |
| |
| port { |
| panel_in: endpoint { |
| remote-endpoint = <&mdss_dsi0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dsi0_out { |
| data-lanes = <0 1 2 3>; |
| remote-endpoint = <&panel_in>; |
| }; |
| |
| &mdss_dsi0_phy { |
| status = "okay"; |
| }; |
| |
| &pm6125_gpios { |
| vol_up_n: vol-up-n-state { |
| pins = "gpio5"; |
| function = "normal"; |
| power-source = <0>; |
| bias-pull-up; |
| input-enable; |
| }; |
| }; |
| |
| &pmi632_lpg { |
| status = "okay"; |
| |
| multi-led { |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_STATUS; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@1 { |
| reg = <1>; |
| color = <LED_COLOR_ID_RED>; |
| }; |
| |
| led@2 { |
| reg = <2>; |
| color = <LED_COLOR_ID_GREEN>; |
| }; |
| |
| led@3 { |
| reg = <3>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| }; |
| }; |
| |
| &pmi632_typec { |
| status = "okay"; |
| |
| connector { |
| compatible = "usb-c-connector"; |
| |
| power-role = "dual"; |
| data-role = "dual"; |
| self-powered; |
| |
| typec-power-opmode = "default"; |
| pd-disable; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| pmi632_hs_in: endpoint { |
| remote-endpoint = <&usb_dwc3_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| pmi632_ss_in: endpoint { |
| remote-endpoint = <&usb_qmpphy_out>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &pmi632_vbus { |
| regulator-min-microamp = <500000>; |
| regulator-max-microamp = <1000000>; |
| status = "okay"; |
| }; |
| |
| &pon_pwrkey { |
| status = "okay"; |
| }; |
| |
| &pon_resin { |
| linux,code = <KEY_VOLUMEDOWN>; |
| status = "okay"; |
| }; |
| |
| &qupv3_id_0 { |
| status = "okay"; |
| }; |
| |
| &remoteproc_adsp { |
| firmware-name = "qcom/sm6115/Fxtec/QX1050/adsp.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_cdsp { |
| firmware-name = "qcom/sm6115/Fxtec/QX1050/cdsp.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_mpss { |
| firmware-name = "qcom/sm6115/Fxtec/QX1050/modem.mbn"; |
| status = "okay"; |
| }; |
| |
| &rpm_requests { |
| regulators-0 { |
| compatible = "qcom,rpm-pm6125-regulators"; |
| |
| pm6125_s6a: s6 { |
| regulator-min-microvolt = <304000>; |
| regulator-max-microvolt = <1456000>; |
| }; |
| |
| pm6125_s7a: s7 { |
| regulator-min-microvolt = <1280000>; |
| regulator-max-microvolt = <2040000>; |
| }; |
| |
| pm6125_s8a: s8 { |
| regulator-min-microvolt = <1064000>; |
| regulator-max-microvolt = <1304000>; |
| }; |
| |
| pm6125_l1a: l1 { |
| regulator-min-microvolt = <952000>; |
| regulator-max-microvolt = <1152000>; |
| }; |
| |
| pm6125_l4a: l4 { |
| regulator-min-microvolt = <488000>; |
| regulator-max-microvolt = <1000000>; |
| }; |
| |
| pm6125_l5a: l5 { |
| regulator-min-microvolt = <1648000>; |
| regulator-max-microvolt = <3056000>; |
| regulator-allow-set-load; |
| }; |
| |
| pm6125_l6a: l6 { |
| regulator-min-microvolt = <576000>; |
| regulator-max-microvolt = <656000>; |
| }; |
| |
| pm6125_l7a: l7 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1304000>; |
| }; |
| |
| pm6125_l8a: l8 { |
| regulator-min-microvolt = <400000>; |
| regulator-max-microvolt = <728000>; |
| }; |
| |
| pm6125_l9a: l9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2000000>; |
| }; |
| |
| pm6125_l10a: l10 { |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <1904000>; |
| }; |
| |
| pm6125_l11a: l11 { |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <1952000>; |
| regulator-allow-set-load; |
| }; |
| |
| pm6125_l12a: l12 { |
| regulator-min-microvolt = <1624000>; |
| regulator-max-microvolt = <1984000>; |
| }; |
| |
| pm6125_l13a: l13 { |
| regulator-min-microvolt = <1504000>; |
| regulator-max-microvolt = <1952000>; |
| }; |
| |
| pm6125_l14a: l14 { |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <1904000>; |
| }; |
| |
| pm6125_l15a: l15 { |
| regulator-min-microvolt = <2920000>; |
| regulator-max-microvolt = <3232000>; |
| }; |
| |
| pm6125_l16a: l16 { |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <1904000>; |
| }; |
| |
| pm6125_l17a: l17 { |
| regulator-min-microvolt = <1152000>; |
| regulator-max-microvolt = <1384000>; |
| }; |
| |
| pm6125_l18a: l18 { |
| regulator-min-microvolt = <1104000>; |
| regulator-max-microvolt = <1312000>; |
| }; |
| |
| pm6125_l19a: l19 { |
| regulator-min-microvolt = <1624000>; |
| regulator-max-microvolt = <3304000>; |
| }; |
| |
| pm6125_l20a: l20 { |
| regulator-min-microvolt = <1624000>; |
| regulator-max-microvolt = <3304000>; |
| }; |
| |
| pm6125_l21a: l21 { |
| regulator-min-microvolt = <2400000>; |
| regulator-max-microvolt = <3600000>; |
| }; |
| |
| pm6125_l22a: l22 { |
| regulator-min-microvolt = <2952000>; |
| regulator-max-microvolt = <3304000>; |
| }; |
| |
| pm6125_l23a: l23 { |
| regulator-min-microvolt = <3200000>; |
| regulator-max-microvolt = <3400000>; |
| }; |
| |
| pm6125_l24a: l24 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <3600000>; |
| regulator-allow-set-load; |
| }; |
| }; |
| }; |
| |
| &sdc2_state_off { |
| cd-pins { |
| pins = "gpio88"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| &sdc2_state_on { |
| cd-pins { |
| pins = "gpio88"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| &sdhc_2 { |
| pinctrl-0 = <&sdc2_state_on>; |
| pinctrl-1 = <&sdc2_state_off>; |
| pinctrl-names = "default", "sleep"; |
| |
| cd-gpios = <&tlmm 88 GPIO_ACTIVE_LOW>; |
| |
| vmmc-supply = <&pm6125_l22a>; |
| vqmmc-supply = <&pm6125_l5a>; |
| |
| status = "okay"; |
| }; |
| |
| &sleep_clk { |
| clock-frequency = <32764>; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <0 4>, <14 4>; |
| |
| key_camera_n: key-camera-n-state { |
| pins = "gpio18"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| panel_en_n: panel-en-n-state { |
| pins = "gpio65"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| ts_rst_n: ts-rst-n-state { |
| pins = "gpio71"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| |
| ts_int_n: ts-int-n-state { |
| pins = "gpio80"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| |
| mdss_dsi_n: mdss-dsi-n-state { |
| pins = "gpio82"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| hall_sensor_n: hall-sensor-n-state { |
| pins = "gpio96"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| &ufs_mem_hc { |
| vcc-supply = <&pm6125_l24a>; |
| vcc-max-microamp = <600000>; |
| vccq2-supply = <&pm6125_l11a>; |
| vccq2-max-microamp = <600000>; |
| vdd-hba-supply = <&pm6125_l18a>; |
| status = "okay"; |
| }; |
| |
| &ufs_mem_phy { |
| vdda-phy-supply = <&pm6125_l4a>; |
| vdda-pll-supply = <&pm6125_l12a>; |
| status = "okay"; |
| }; |
| |
| &usb { |
| status = "okay"; |
| }; |
| |
| &usb_dwc3_hs { |
| remote-endpoint = <&pmi632_hs_in>; |
| }; |
| |
| &usb_hsphy { |
| vdd-supply = <&pm6125_l4a>; |
| vdda-pll-supply = <&pm6125_l12a>; |
| vdda-phy-dpdm-supply = <&pm6125_l15a>; |
| status = "okay"; |
| }; |
| |
| &usb_qmpphy { |
| vdda-phy-supply = <&pm6125_l4a>; |
| vdda-pll-supply = <&pm6125_l12a>; |
| status = "okay"; |
| }; |
| |
| &usb_qmpphy_out { |
| remote-endpoint = <&pmi632_ss_in>; |
| }; |
| |
| &wifi { |
| vdd-0.8-cx-mx-supply = <&pm6125_l8a>; |
| vdd-1.8-xo-supply = <&pm6125_l16a>; |
| vdd-1.3-rfa-supply = <&pm6125_l17a>; |
| vdd-3.3-ch0-supply = <&pm6125_l23a>; |
| |
| qcom,ath10k-calibration-variant = "Fxtec_QX1050"; |
| |
| status = "okay"; |
| }; |
| |
| &xo_board { |
| clock-frequency = <19200000>; |
| }; |
