| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (c) 2021, The Linux Foundation. All rights reserved. |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/arm/qcom,ids.h> |
| #include <dt-bindings/firmware/qcom,scm.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include "sm7125.dtsi" |
| #include "pm6150.dtsi" |
| #include "pm6150l.dtsi" |
| |
| /delete-node/ &ipa_fw_mem; |
| /delete-node/ &rmtfs_mem; |
| |
| / { |
| chassis-type = "handset"; |
| |
| qcom,msm-id = <QCOM_ID_SM7125 0>; |
| |
| chosen { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| framebuffer@9c000000 { |
| compatible = "simple-framebuffer"; |
| reg = <0x0 0x9c000000 0x0 (1080 * 2400 * 4)>; |
| width = <1080>; |
| height = <2400>; |
| stride = <(1080 * 4)>; |
| format = "a8r8g8b8"; |
| clocks = <&gcc GCC_DISP_HF_AXI_CLK>; |
| }; |
| }; |
| |
| gpio_keys: gpio-keys { |
| compatible = "gpio-keys"; |
| |
| key-vol-up { |
| label = "Volume Up"; |
| linux,code = <KEY_VOLUMEUP>; |
| gpios = <&pm6150l_gpios 2 GPIO_ACTIVE_LOW>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| wakeup-source; |
| }; |
| }; |
| |
| reserved-memory { |
| mpss_mem: memory@86000000 { |
| reg = <0x0 0x86000000 0x0 0x8400000>; |
| no-map; |
| }; |
| |
| venus_mem: memory@8ee00000 { |
| reg = <0x0 0x8ee00000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| cdsp_mem: memory@8f300000 { |
| reg = <0x0 0x8f300000 0x0 0x1e00000>; |
| no-map; |
| }; |
| |
| adsp_mem: memory@91100000 { |
| reg = <0x0 0x91100000 0x0 0x2800000>; |
| no-map; |
| }; |
| |
| wlan_mem: memory@93900000 { |
| reg = <0x0 0x93900000 0x0 0x200000>; |
| no-map; |
| }; |
| |
| ipa_fw_mem: memory@93b00000 { |
| reg = <0x0 0x93b00000 0x0 0x10000>; |
| no-map; |
| }; |
| |
| gpu_mem: memory@93b15000 { |
| reg = <0x0 0x93b15000 0x0 0x2000>; |
| no-map; |
| }; |
| |
| cont_splash_mem: memory@9c000000 { |
| reg = <0x0 0x9c000000 0x0 (1080 * 2400 * 4)>; |
| no-map; |
| }; |
| |
| pstore_mem: ramoops@9d800000 { |
| compatible = "ramoops"; |
| reg = <0x0 0x9d800000 0x0 0x400000>; |
| record-size = <0x80000>; |
| pmsg-size = <0x200000>; |
| console-size = <0x100000>; |
| }; |
| |
| rmtfs_mem: memory@fa601000 { |
| compatible = "qcom,rmtfs-mem"; |
| reg = <0x0 0xfa601000 0x0 0x200000>; |
| no-map; |
| |
| qcom,client-id = <1>; |
| qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>; |
| }; |
| }; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm6150-rpmh-regulators"; |
| qcom,pmic-id = "a"; |
| |
| vreg_s1a_1p1: smps1 { |
| regulator-min-microvolt = <1128000>; |
| regulator-max-microvolt = <1128000>; |
| }; |
| |
| vreg_s4a_1p0: smps4 { |
| regulator-min-microvolt = <824000>; |
| regulator-max-microvolt = <1120000>; |
| }; |
| |
| vreg_s5a_2p0: smps5 { |
| regulator-min-microvolt = <1744000>; |
| regulator-max-microvolt = <2040000>; |
| }; |
| |
| vreg_l1a_1p2: ldo1 { |
| regulator-min-microvolt = <1178000>; |
| regulator-max-microvolt = <1256000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2a_1p0: ldo2 { |
| regulator-min-microvolt = <944000>; |
| regulator-max-microvolt = <1056000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3a_1p0: ldo3 { |
| regulator-min-microvolt = <968000>; |
| regulator-max-microvolt = <1064000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4a_0p88: ldo4 { |
| regulator-min-microvolt = <824000>; |
| regulator-max-microvolt = <928000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5a_2p7: ldo5 { |
| regulator-min-microvolt = <2496000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6a_0p6: ldo6 { |
| regulator-min-microvolt = <568000>; |
| regulator-max-microvolt = <648000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9a_0p664: ldo9 { |
| regulator-min-microvolt = <488000>; |
| regulator-max-microvolt = <800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10a_1p8: ldo10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1832000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l11a_1p8: ldo11 { |
| regulator-min-microvolt = <1696000>; |
| regulator-max-microvolt = <1904000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12a_1p8: ldo12 { |
| regulator-min-microvolt = <1696000>; |
| regulator-max-microvolt = <1952000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13a_1p8: ldo13 { |
| regulator-min-microvolt = <1696000>; |
| regulator-max-microvolt = <1904000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14a_1p8: ldo14 { |
| regulator-min-microvolt = <1728000>; |
| regulator-max-microvolt = <1832000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l15a_1p8: ldo15 { |
| regulator-min-microvolt = <1696000>; |
| regulator-max-microvolt = <1904000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l16a_2p7: ldo16 { |
| regulator-min-microvolt = <2496000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l17a_3p1: ldo17 { |
| regulator-min-microvolt = <2920000>; |
| regulator-max-microvolt = <3232000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l18a_3p0: ldo18 { |
| regulator-min-microvolt = <1696000>; |
| regulator-max-microvolt = <1904000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l19a_3p0: ldo19 { |
| regulator-min-microvolt = <2696000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm6150l-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vreg_s8c_1p3: smps8 { |
| regulator-min-microvolt = <1120000>; |
| regulator-max-microvolt = <1408000>; |
| }; |
| |
| vreg_l1c_1p8: ldo1 { |
| regulator-min-microvolt = <1616000>; |
| regulator-max-microvolt = <1984000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2c_1p3: ldo2 { |
| regulator-min-microvolt = <1168000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3c_1p23: ldo3 { |
| regulator-min-microvolt = <1144000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4c_1p8: ldo4 { |
| regulator-min-microvolt = <1648000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5c_1p8: ldo5 { |
| regulator-min-microvolt = <1648000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6c_3p0: ldo6 { |
| regulator-min-microvolt = <1648000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7c_3p0: ldo7 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3312000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8c_1p8: ldo8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1904000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9c_2p9: ldo9 { |
| regulator-min-microvolt = <2952000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10c_3p3: ldo10 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l11c_3p3: ldo11 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_bob: bob { |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; |
| }; |
| }; |
| }; |
| |
| &dispcc { |
| /* HACK: disable until a panel driver is ready to retain simplefb */ |
| status = "disabled"; |
| }; |
| |
| &pm6150_resin { |
| linux,code = <KEY_VOLUMEDOWN>; |
| status = "okay"; |
| }; |
| |
| &pm6150_rtc { |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| cd-gpios = <&tlmm 69 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default","sleep"; |
| pinctrl-0 = <&sdc2_on>; |
| pinctrl-1 = <&sdc2_off>; |
| vmmc-supply = <&vreg_l9c_2p9>; |
| vqmmc-supply = <&vreg_l6c_3p0>; |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <0 4>, <34 4>, <59 4>; |
| |
| sdc2_on: sdc2-on-state { |
| clk-pins { |
| pins = "sdc2_clk"; |
| bias-disable; |
| drive-strength = <16>; |
| }; |
| |
| cmd-pins { |
| pins = "sdc2_cmd"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| data-pins { |
| pins = "sdc2_data"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| sd-cd-pins { |
| pins = "gpio69"; |
| function = "gpio"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| sdc2_off: sdc2-off-state { |
| clk-pins { |
| pins = "sdc2_clk"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| cmd-pins { |
| pins = "sdc2_cmd"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| data-pins { |
| pins = "sdc2_data"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| sd-cd-pins { |
| pins = "gpio69"; |
| function = "gpio"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| }; |
| |
| &ufs_mem_hc { |
| reset-gpios = <&tlmm 119 GPIO_ACTIVE_LOW>; |
| |
| vcc-supply = <&vreg_l19a_3p0>; |
| vcc-max-microamp = <600000>; |
| vccq2-supply = <&vreg_l12a_1p8>; |
| vccq2-max-microamp = <600000>; |
| status = "okay"; |
| }; |
| |
| &ufs_mem_phy { |
| vdda-phy-supply = <&vreg_l4a_0p88>; |
| vdda-pll-supply = <&vreg_l3c_1p23>; |
| status = "okay"; |
| }; |
| |
| &usb_1 { |
| qcom,select-utmi-as-pipe-clk; |
| status = "okay"; |
| }; |
| |
| &usb_1_dwc3 { |
| dr_mode = "peripheral"; |
| maximum-speed = "high-speed"; |
| status = "okay"; |
| }; |
| |
| &usb_1_hsphy { |
| vdd-supply = <&vreg_l4a_0p88>; |
| vdda-phy-dpdm-supply = <&vreg_l17a_3p1>; |
| vdda-pll-supply = <&vreg_l11a_1p8>; |
| status = "okay"; |
| }; |
| |
| &usb_1_qmpphy { |
| vdda-phy-supply = <&vreg_l4a_0p88>; |
| vdda-pll-supply = <&vreg_l3c_1p23>; |
| status = "okay"; |
| }; |
