| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved. |
| */ |
| |
| #include <dt-bindings/clock/qcom,rpmh.h> |
| #include <dt-bindings/clock/qcom,sc8280xp-lpasscc.h> |
| #include <dt-bindings/clock/qcom,x1e80100-dispcc.h> |
| #include <dt-bindings/clock/qcom,x1e80100-gcc.h> |
| #include <dt-bindings/clock/qcom,x1e80100-gpucc.h> |
| #include <dt-bindings/clock/qcom,x1e80100-tcsr.h> |
| #include <dt-bindings/dma/qcom-gpi.h> |
| #include <dt-bindings/interconnect/qcom,icc.h> |
| #include <dt-bindings/interconnect/qcom,x1e80100-rpmh.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/mailbox/qcom-ipcc.h> |
| #include <dt-bindings/phy/phy-qcom-qmp.h> |
| #include <dt-bindings/power/qcom,rpmhpd.h> |
| #include <dt-bindings/power/qcom-rpmpd.h> |
| #include <dt-bindings/soc/qcom,gpr.h> |
| #include <dt-bindings/soc/qcom,rpmh-rsc.h> |
| #include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h> |
| |
| / { |
| interrupt-parent = <&intc>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| chosen { }; |
| |
| clocks { |
| xo_board: xo-board { |
| compatible = "fixed-clock"; |
| clock-frequency = <76800000>; |
| #clock-cells = <0>; |
| }; |
| |
| sleep_clk: sleep-clk { |
| compatible = "fixed-clock"; |
| clock-frequency = <32000>; |
| #clock-cells = <0>; |
| }; |
| |
| bi_tcxo_div2: bi-tcxo-div2-clk { |
| compatible = "fixed-factor-clock"; |
| #clock-cells = <0>; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-mult = <1>; |
| clock-div = <2>; |
| }; |
| |
| bi_tcxo_ao_div2: bi-tcxo-ao-div2-clk { |
| compatible = "fixed-factor-clock"; |
| #clock-cells = <0>; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK_A>; |
| clock-mult = <1>; |
| clock-div = <2>; |
| }; |
| }; |
| |
| cpus { |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| CPU0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x0>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_0>; |
| power-domains = <&CPU_PD0>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| |
| L2_0: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| }; |
| |
| CPU1: cpu@100 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x100>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_0>; |
| power-domains = <&CPU_PD1>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| }; |
| |
| CPU2: cpu@200 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x200>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_0>; |
| power-domains = <&CPU_PD2>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| }; |
| |
| CPU3: cpu@300 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x300>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_0>; |
| power-domains = <&CPU_PD3>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| }; |
| |
| CPU4: cpu@10000 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x10000>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_1>; |
| power-domains = <&CPU_PD4>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| |
| L2_1: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| }; |
| |
| CPU5: cpu@10100 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x10100>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_1>; |
| power-domains = <&CPU_PD5>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| }; |
| |
| CPU6: cpu@10200 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x10200>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_1>; |
| power-domains = <&CPU_PD6>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| }; |
| |
| CPU7: cpu@10300 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x10300>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_1>; |
| power-domains = <&CPU_PD7>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| }; |
| |
| CPU8: cpu@20000 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x20000>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_2>; |
| power-domains = <&CPU_PD8>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| |
| L2_2: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| }; |
| |
| CPU9: cpu@20100 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x20100>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_2>; |
| power-domains = <&CPU_PD9>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| }; |
| |
| CPU10: cpu@20200 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x20200>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_2>; |
| power-domains = <&CPU_PD10>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| }; |
| |
| CPU11: cpu@20300 { |
| device_type = "cpu"; |
| compatible = "qcom,oryon"; |
| reg = <0x0 0x20300>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_2>; |
| power-domains = <&CPU_PD11>; |
| power-domain-names = "psci"; |
| cpu-idle-states = <&CLUSTER_C4>; |
| }; |
| |
| cpu-map { |
| cluster0 { |
| core0 { |
| cpu = <&CPU0>; |
| }; |
| |
| core1 { |
| cpu = <&CPU1>; |
| }; |
| |
| core2 { |
| cpu = <&CPU2>; |
| }; |
| |
| core3 { |
| cpu = <&CPU3>; |
| }; |
| }; |
| |
| cluster1 { |
| core0 { |
| cpu = <&CPU4>; |
| }; |
| |
| core1 { |
| cpu = <&CPU5>; |
| }; |
| |
| core2 { |
| cpu = <&CPU6>; |
| }; |
| |
| core3 { |
| cpu = <&CPU7>; |
| }; |
| }; |
| |
| cluster2 { |
| core0 { |
| cpu = <&CPU8>; |
| }; |
| |
| core1 { |
| cpu = <&CPU9>; |
| }; |
| |
| core2 { |
| cpu = <&CPU10>; |
| }; |
| |
| core3 { |
| cpu = <&CPU11>; |
| }; |
| }; |
| }; |
| |
| idle-states { |
| entry-method = "psci"; |
| |
| CLUSTER_C4: cpu-sleep-0 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "ret"; |
| arm,psci-suspend-param = <0x00000004>; |
| entry-latency-us = <180>; |
| exit-latency-us = <320>; |
| min-residency-us = <1000>; |
| }; |
| }; |
| |
| domain-idle-states { |
| CLUSTER_CL4: cluster-sleep-0 { |
| compatible = "domain-idle-state"; |
| idle-state-name = "l2-ret"; |
| arm,psci-suspend-param = <0x01000044>; |
| entry-latency-us = <350>; |
| exit-latency-us = <500>; |
| min-residency-us = <2500>; |
| }; |
| |
| CLUSTER_CL5: cluster-sleep-1 { |
| compatible = "domain-idle-state"; |
| idle-state-name = "ret-pll-off"; |
| arm,psci-suspend-param = <0x01000054>; |
| entry-latency-us = <2200>; |
| exit-latency-us = <2500>; |
| min-residency-us = <7000>; |
| }; |
| }; |
| }; |
| |
| firmware { |
| scm: scm { |
| compatible = "qcom,scm-x1e80100", "qcom,scm"; |
| interconnects = <&aggre2_noc MASTER_CRYPTO QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| }; |
| }; |
| |
| clk_virt: interconnect-0 { |
| compatible = "qcom,x1e80100-clk-virt"; |
| #interconnect-cells = <2>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| mc_virt: interconnect-1 { |
| compatible = "qcom,x1e80100-mc-virt"; |
| #interconnect-cells = <2>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| /* We expect the bootloader to fill in the size */ |
| reg = <0 0x80000000 0 0>; |
| }; |
| |
| pmu { |
| compatible = "arm,armv8-pmuv3"; |
| interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| |
| CPU_PD0: power-domain-cpu0 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD0>; |
| }; |
| |
| CPU_PD1: power-domain-cpu1 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD0>; |
| }; |
| |
| CPU_PD2: power-domain-cpu2 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD0>; |
| }; |
| |
| CPU_PD3: power-domain-cpu3 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD0>; |
| }; |
| |
| CPU_PD4: power-domain-cpu4 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD1>; |
| }; |
| |
| CPU_PD5: power-domain-cpu5 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD1>; |
| }; |
| |
| CPU_PD6: power-domain-cpu6 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD1>; |
| }; |
| |
| CPU_PD7: power-domain-cpu7 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD1>; |
| }; |
| |
| CPU_PD8: power-domain-cpu8 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD2>; |
| }; |
| |
| CPU_PD9: power-domain-cpu9 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD2>; |
| }; |
| |
| CPU_PD10: power-domain-cpu10 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD2>; |
| }; |
| |
| CPU_PD11: power-domain-cpu11 { |
| #power-domain-cells = <0>; |
| power-domains = <&CLUSTER_PD2>; |
| }; |
| |
| CLUSTER_PD0: power-domain-cpu-cluster0 { |
| #power-domain-cells = <0>; |
| domain-idle-states = <&CLUSTER_CL4>, <&CLUSTER_CL5>; |
| power-domains = <&SYSTEM_PD>; |
| }; |
| |
| CLUSTER_PD1: power-domain-cpu-cluster1 { |
| #power-domain-cells = <0>; |
| domain-idle-states = <&CLUSTER_CL4>, <&CLUSTER_CL5>; |
| power-domains = <&SYSTEM_PD>; |
| }; |
| |
| CLUSTER_PD2: power-domain-cpu-cluster2 { |
| #power-domain-cells = <0>; |
| domain-idle-states = <&CLUSTER_CL4>, <&CLUSTER_CL5>; |
| power-domains = <&SYSTEM_PD>; |
| }; |
| |
| SYSTEM_PD: power-domain-system { |
| #power-domain-cells = <0>; |
| /* TODO: system-wide idle states */ |
| }; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| gunyah_hyp_mem: gunyah-hyp@80000000 { |
| reg = <0x0 0x80000000 0x0 0x800000>; |
| no-map; |
| }; |
| |
| hyp_elf_package_mem: hyp-elf-package@80800000 { |
| reg = <0x0 0x80800000 0x0 0x200000>; |
| no-map; |
| }; |
| |
| ncc_mem: ncc@80a00000 { |
| reg = <0x0 0x80a00000 0x0 0x400000>; |
| no-map; |
| }; |
| |
| cpucp_log_mem: cpucp-log@80e00000 { |
| reg = <0x0 0x80e00000 0x0 0x40000>; |
| no-map; |
| }; |
| |
| cpucp_mem: cpucp@80e40000 { |
| reg = <0x0 0x80e40000 0x0 0x540000>; |
| no-map; |
| }; |
| |
| reserved-region@81380000 { |
| reg = <0x0 0x81380000 0x0 0x80000>; |
| no-map; |
| }; |
| |
| tags_mem: tags-region@81400000 { |
| reg = <0x0 0x81400000 0x0 0x1a0000>; |
| no-map; |
| }; |
| |
| xbl_dtlog_mem: xbl-dtlog@81a00000 { |
| reg = <0x0 0x81a00000 0x0 0x40000>; |
| no-map; |
| }; |
| |
| xbl_ramdump_mem: xbl-ramdump@81a40000 { |
| reg = <0x0 0x81a40000 0x0 0x1c0000>; |
| no-map; |
| }; |
| |
| aop_image_mem: aop-image@81c00000 { |
| reg = <0x0 0x81c00000 0x0 0x60000>; |
| no-map; |
| }; |
| |
| aop_cmd_db_mem: aop-cmd-db@81c60000 { |
| compatible = "qcom,cmd-db"; |
| reg = <0x0 0x81c60000 0x0 0x20000>; |
| no-map; |
| }; |
| |
| aop_config_mem: aop-config@81c80000 { |
| reg = <0x0 0x81c80000 0x0 0x20000>; |
| no-map; |
| }; |
| |
| tme_crash_dump_mem: tme-crash-dump@81ca0000 { |
| reg = <0x0 0x81ca0000 0x0 0x40000>; |
| no-map; |
| }; |
| |
| tme_log_mem: tme-log@81ce0000 { |
| reg = <0x0 0x81ce0000 0x0 0x4000>; |
| no-map; |
| }; |
| |
| uefi_log_mem: uefi-log@81ce4000 { |
| reg = <0x0 0x81ce4000 0x0 0x10000>; |
| no-map; |
| }; |
| |
| secdata_apss_mem: secdata-apss@81cff000 { |
| reg = <0x0 0x81cff000 0x0 0x1000>; |
| no-map; |
| }; |
| |
| pdp_ns_shared_mem: pdp-ns-shared@81e00000 { |
| reg = <0x0 0x81e00000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| gpu_prr_mem: gpu-prr@81f00000 { |
| reg = <0x0 0x81f00000 0x0 0x10000>; |
| no-map; |
| }; |
| |
| tpm_control_mem: tpm-control@81f10000 { |
| reg = <0x0 0x81f10000 0x0 0x10000>; |
| no-map; |
| }; |
| |
| usb_ucsi_shared_mem: usb-ucsi-shared@81f20000 { |
| reg = <0x0 0x81f20000 0x0 0x10000>; |
| no-map; |
| }; |
| |
| pld_pep_mem: pld-pep@81f30000 { |
| reg = <0x0 0x81f30000 0x0 0x6000>; |
| no-map; |
| }; |
| |
| pld_gmu_mem: pld-gmu@81f36000 { |
| reg = <0x0 0x81f36000 0x0 0x1000>; |
| no-map; |
| }; |
| |
| pld_pdp_mem: pld-pdp@81f37000 { |
| reg = <0x0 0x81f37000 0x0 0x1000>; |
| no-map; |
| }; |
| |
| tz_stat_mem: tz-stat@82700000 { |
| reg = <0x0 0x82700000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| xbl_tmp_buffer_mem: xbl-tmp-buffer@82800000 { |
| reg = <0x0 0x82800000 0x0 0xc00000>; |
| no-map; |
| }; |
| |
| adsp_rpc_remote_heap_mem: adsp-rpc-remote-heap@84b00000 { |
| reg = <0x0 0x84b00000 0x0 0x800000>; |
| no-map; |
| }; |
| |
| spu_secure_shared_memory_mem: spu-secure-shared-memory@85300000 { |
| reg = <0x0 0x85300000 0x0 0x80000>; |
| no-map; |
| }; |
| |
| adsp_boot_dtb_mem: adsp-boot-dtb@866c0000 { |
| reg = <0x0 0x866c0000 0x0 0x40000>; |
| no-map; |
| }; |
| |
| spss_region_mem: spss-region@86700000 { |
| reg = <0x0 0x86700000 0x0 0x400000>; |
| no-map; |
| }; |
| |
| adsp_boot_mem: adsp-boot@86b00000 { |
| reg = <0x0 0x86b00000 0x0 0xc00000>; |
| no-map; |
| }; |
| |
| video_mem: video@87700000 { |
| reg = <0x0 0x87700000 0x0 0x700000>; |
| no-map; |
| }; |
| |
| adspslpi_mem: adspslpi@87e00000 { |
| reg = <0x0 0x87e00000 0x0 0x3a00000>; |
| no-map; |
| }; |
| |
| q6_adsp_dtb_mem: q6-adsp-dtb@8b800000 { |
| reg = <0x0 0x8b800000 0x0 0x80000>; |
| no-map; |
| }; |
| |
| cdsp_mem: cdsp@8b900000 { |
| reg = <0x0 0x8b900000 0x0 0x2000000>; |
| no-map; |
| }; |
| |
| q6_cdsp_dtb_mem: q6-cdsp-dtb@8d900000 { |
| reg = <0x0 0x8d900000 0x0 0x80000>; |
| no-map; |
| }; |
| |
| gpu_microcode_mem: gpu-microcode@8d9fe000 { |
| reg = <0x0 0x8d9fe000 0x0 0x2000>; |
| no-map; |
| }; |
| |
| cvp_mem: cvp@8da00000 { |
| reg = <0x0 0x8da00000 0x0 0x700000>; |
| no-map; |
| }; |
| |
| camera_mem: camera@8e100000 { |
| reg = <0x0 0x8e100000 0x0 0x800000>; |
| no-map; |
| }; |
| |
| av1_encoder_mem: av1-encoder@8e900000 { |
| reg = <0x0 0x8e900000 0x0 0x700000>; |
| no-map; |
| }; |
| |
| reserved-region@8f000000 { |
| reg = <0x0 0x8f000000 0x0 0xa00000>; |
| no-map; |
| }; |
| |
| wpss_mem: wpss@8fa00000 { |
| reg = <0x0 0x8fa00000 0x0 0x1900000>; |
| no-map; |
| }; |
| |
| q6_wpss_dtb_mem: q6-wpss-dtb@91300000 { |
| reg = <0x0 0x91300000 0x0 0x80000>; |
| no-map; |
| }; |
| |
| xbl_sc_mem: xbl-sc@d8000000 { |
| reg = <0x0 0xd8000000 0x0 0x40000>; |
| no-map; |
| }; |
| |
| reserved-region@d8040000 { |
| reg = <0x0 0xd8040000 0x0 0xa0000>; |
| no-map; |
| }; |
| |
| qtee_mem: qtee@d80e0000 { |
| reg = <0x0 0xd80e0000 0x0 0x520000>; |
| no-map; |
| }; |
| |
| ta_mem: ta@d8600000 { |
| reg = <0x0 0xd8600000 0x0 0x8a00000>; |
| no-map; |
| }; |
| |
| tags_mem1: tags@e1000000 { |
| reg = <0x0 0xe1000000 0x0 0x26a0000>; |
| no-map; |
| }; |
| |
| llcc_lpi_mem: llcc-lpi@ff800000 { |
| reg = <0x0 0xff800000 0x0 0x600000>; |
| no-map; |
| }; |
| |
| smem_mem: smem@ffe00000 { |
| compatible = "qcom,smem"; |
| reg = <0x0 0xffe00000 0x0 0x200000>; |
| hwlocks = <&tcsr_mutex 3>; |
| no-map; |
| }; |
| }; |
| |
| smp2p-adsp { |
| compatible = "qcom,smp2p"; |
| |
| interrupts-extended = <&ipcc IPCC_CLIENT_LPASS |
| IPCC_MPROC_SIGNAL_SMP2P |
| IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&ipcc IPCC_CLIENT_LPASS |
| IPCC_MPROC_SIGNAL_SMP2P>; |
| |
| qcom,smem = <443>, <429>; |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <2>; |
| |
| smp2p_adsp_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| smp2p_adsp_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-cdsp { |
| compatible = "qcom,smp2p"; |
| |
| interrupts-extended = <&ipcc IPCC_CLIENT_CDSP |
| IPCC_MPROC_SIGNAL_SMP2P |
| IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&ipcc IPCC_CLIENT_CDSP |
| IPCC_MPROC_SIGNAL_SMP2P>; |
| |
| qcom,smem = <94>, <432>; |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <5>; |
| |
| smp2p_cdsp_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| smp2p_cdsp_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| soc: soc@0 { |
| compatible = "simple-bus"; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| dma-ranges = <0 0 0 0 0x10 0>; |
| ranges = <0 0 0 0 0x10 0>; |
| |
| gcc: clock-controller@100000 { |
| compatible = "qcom,x1e80100-gcc"; |
| reg = <0 0x00100000 0 0x200000>; |
| |
| clocks = <&bi_tcxo_div2>, |
| <&sleep_clk>, |
| <0>, |
| <&pcie4_phy>, |
| <&pcie5_phy>, |
| <&pcie6a_phy>, |
| <0>, |
| <&usb_1_ss0_qmpphy QMP_USB43DP_USB3_PIPE_CLK>, |
| <&usb_1_ss1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>, |
| <&usb_1_ss2_qmpphy QMP_USB43DP_USB3_PIPE_CLK>; |
| |
| power-domains = <&rpmhpd RPMHPD_CX>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| }; |
| |
| ipcc: mailbox@408000 { |
| compatible = "qcom,x1e80100-ipcc", "qcom,ipcc"; |
| reg = <0 0x00408000 0 0x1000>; |
| |
| interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| |
| #mbox-cells = <2>; |
| }; |
| |
| gpi_dma2: dma-controller@800000 { |
| compatible = "qcom,x1e80100-gpi-dma", "qcom,sm6350-gpi-dma"; |
| reg = <0 0x00800000 0 0x60000>; |
| |
| interrupts = <GIC_SPI 788 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 789 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 790 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 791 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 792 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 793 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 794 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 795 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 796 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 797 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 798 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 799 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dma-channels = <12>; |
| dma-channel-mask = <0x3e>; |
| #dma-cells = <3>; |
| |
| iommus = <&apps_smmu 0x436 0x0>; |
| |
| status = "disabled"; |
| }; |
| |
| qupv3_2: geniqup@8c0000 { |
| compatible = "qcom,geni-se-qup"; |
| reg = <0 0x008c0000 0 0x2000>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>, |
| <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>; |
| clock-names = "m-ahb", |
| "s-ahb"; |
| |
| iommus = <&apps_smmu 0x423 0x0>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| status = "disabled"; |
| |
| i2c16: i2c@880000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00880000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 808 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>, |
| <&gpi_dma2 1 0 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c16_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi16: spi@880000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00880000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 808 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>, |
| <&gpi_dma2 1 0 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi16_data_clk>, <&qup_spi16_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c17: i2c@884000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00884000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 809 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>, |
| <&gpi_dma2 1 1 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c17_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi17: spi@884000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00884000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 809 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>, |
| <&gpi_dma2 1 1 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi17_data_clk>, <&qup_spi17_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c18: i2c@888000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00888000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 810 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>, |
| <&gpi_dma2 1 2 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c18_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi18: spi@888000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00888000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 810 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>, |
| <&gpi_dma2 1 2 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi18_data_clk>, <&qup_spi18_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c19: i2c@88c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x0088c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 811 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>, |
| <&gpi_dma2 1 3 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c19_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi19: spi@88c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x0088c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 811 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 3 QCOM_GPI_SPI>, |
| <&gpi_dma2 1 3 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi19_data_clk>, <&qup_spi19_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c20: i2c@890000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00890000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 812 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>, |
| <&gpi_dma2 1 4 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c20_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi20: spi@890000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00890000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 812 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 4 QCOM_GPI_SPI>, |
| <&gpi_dma2 1 4 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi20_data_clk>, <&qup_spi20_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c21: i2c@894000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00894000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 813 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>, |
| <&gpi_dma2 1 5 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c21_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi21: spi@894000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00894000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 813 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>, |
| <&gpi_dma2 1 5 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi21_data_clk>, <&qup_spi21_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| uart21: serial@894000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00894000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 813 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config"; |
| |
| pinctrl-0 = <&qup_uart21_default>; |
| pinctrl-names = "default"; |
| |
| status = "disabled"; |
| }; |
| |
| i2c22: i2c@898000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00898000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 6 QCOM_GPI_I2C>, |
| <&gpi_dma2 1 6 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c22_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi22: spi@898000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00898000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 6 QCOM_GPI_SPI>, |
| <&gpi_dma2 1 6 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi22_data_clk>, <&qup_spi22_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c23: i2c@89c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x0089c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 7 QCOM_GPI_I2C>, |
| <&gpi_dma2 1 7 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c23_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi23: spi@89c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x0089c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma2 0 7 QCOM_GPI_SPI>, |
| <&gpi_dma2 1 7 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi23_data_clk>, <&qup_spi23_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| gpi_dma1: dma-controller@a00000 { |
| compatible = "qcom,x1e80100-gpi-dma", "qcom,sm6350-gpi-dma"; |
| reg = <0 0x00a00000 0 0x60000>; |
| |
| interrupts = <GIC_SPI 776 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 777 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 778 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 779 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 780 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 781 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 782 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 783 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 784 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 785 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 786 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 787 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dma-channels = <12>; |
| dma-channel-mask = <0x3e>; |
| #dma-cells = <3>; |
| |
| iommus = <&apps_smmu 0x136 0x0>; |
| |
| status = "disabled"; |
| }; |
| |
| qupv3_1: geniqup@ac0000 { |
| compatible = "qcom,geni-se-qup"; |
| reg = <0 0x00ac0000 0 0x2000>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>, |
| <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>; |
| clock-names = "m-ahb", |
| "s-ahb"; |
| |
| iommus = <&apps_smmu 0x123 0x0>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| status = "disabled"; |
| |
| i2c8: i2c@a80000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a80000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 800 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 0 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c8_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi8: spi@a80000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a80000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 800 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 0 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c9: i2c@a84000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a84000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 801 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 1 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c9_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi9: spi@a84000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a84000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 801 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 1 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c10: i2c@a88000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a88000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 802 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 2 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c10_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi10: spi@a88000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a88000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 802 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 2 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c11: i2c@a8c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a8c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 803 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 3 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c11_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi11: spi@a8c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a8c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 803 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 3 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c12: i2c@a90000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a90000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 804 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 4 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c12_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi12: spi@a90000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a90000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 804 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 4 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c13: i2c@a94000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a94000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 805 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 5 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c13_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi13: spi@a94000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a94000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 805 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 5 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c14: i2c@a98000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a98000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 806 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 6 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c14_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi14: spi@a98000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a98000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 806 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 6 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c15: i2c@a9c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a9c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 807 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 7 QCOM_GPI_I2C>, |
| <&gpi_dma1 1 7 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c15_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi15: spi@a9c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a9c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 807 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma1 0 7 QCOM_GPI_SPI>, |
| <&gpi_dma1 1 7 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| gpi_dma0: dma-controller@b00000 { |
| compatible = "qcom,x1e80100-gpi-dma", "qcom,sm6350-gpi-dma"; |
| reg = <0 0x00b00000 0 0x60000>; |
| |
| interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 599 IRQ_TYPE_LEVEL_HIGH>; |
| |
| dma-channels = <12>; |
| dma-channel-mask = <0x3e>; |
| #dma-cells = <3>; |
| |
| iommus = <&apps_smmu 0x456 0x0>; |
| |
| status = "disabled"; |
| }; |
| |
| qupv3_0: geniqup@bc0000 { |
| compatible = "qcom,geni-se-qup"; |
| reg = <0 0x00bc0000 0 0x2000>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, |
| <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; |
| clock-names = "m-ahb", |
| "s-ahb"; |
| |
| iommus = <&apps_smmu 0x443 0x0>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| status = "disabled"; |
| |
| i2c0: i2c@b80000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00b80000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 0 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c0_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi0: spi@b80000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00b80000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 0 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@b84000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00b84000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 1 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c1_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi1: spi@b84000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00b84000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 1 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@b88000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00b88000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 2 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c2_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| uart2: serial@b88000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00b88000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config"; |
| |
| pinctrl-0 = <&qup_uart2_default>; |
| pinctrl-names = "default"; |
| |
| status = "disabled"; |
| }; |
| |
| spi2: spi@b88000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00b88000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 2 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@b8c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00b8c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 3 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c3_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi3: spi@b8c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00b8c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 3 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@b90000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00b90000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 4 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c4_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi4: spi@b90000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00b90000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 4 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c@b94000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00b94000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 5 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c5_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi5: spi@b94000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00b94000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 5 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c6: i2c@b98000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00b98000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 6 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c6_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi6: spi@b98000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00b98000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 6 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| i2c7: i2c@b9c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00b9c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 7 QCOM_GPI_I2C>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_i2c7_data_clk>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| spi7: spi@b9c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00b9c000 0 0x4000>; |
| |
| interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; |
| clock-names = "se"; |
| |
| interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS |
| &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>, |
| <&aggre2_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "qup-core", |
| "qup-config", |
| "qup-memory"; |
| |
| dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 7 QCOM_GPI_SPI>; |
| dma-names = "tx", |
| "rx"; |
| |
| pinctrl-0 = <&qup_spi7_data_clk>, <&qup_spi7_cs>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| tsens0: thermal-sensor@c271000 { |
| compatible = "qcom,x1e80100-tsens", "qcom,tsens-v2"; |
| reg = <0 0x0c271000 0 0x1000>, |
| <0 0x0c222000 0 0x1000>; |
| |
| interrupts-extended = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>, |
| <&intc GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", |
| "critical"; |
| |
| #qcom,sensors = <16>; |
| |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| tsens1: thermal-sensor@c272000 { |
| compatible = "qcom,x1e80100-tsens", "qcom,tsens-v2"; |
| reg = <0 0x0c272000 0 0x1000>, |
| <0 0x0c223000 0 0x1000>; |
| |
| interrupts-extended = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>, |
| <&intc GIC_SPI 642 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", |
| "critical"; |
| |
| #qcom,sensors = <16>; |
| |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| tsens2: thermal-sensor@c273000 { |
| compatible = "qcom,x1e80100-tsens", "qcom,tsens-v2"; |
| reg = <0 0x0c273000 0 0x1000>, |
| <0 0x0c224000 0 0x1000>; |
| |
| interrupts-extended = <&pdc 28 IRQ_TYPE_LEVEL_HIGH>, |
| <&intc GIC_SPI 643 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", |
| "critical"; |
| |
| #qcom,sensors = <16>; |
| |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| tsens3: thermal-sensor@c274000 { |
| compatible = "qcom,x1e80100-tsens", "qcom,tsens-v2"; |
| reg = <0 0x0c274000 0 0x1000>, |
| <0 0x0c225000 0 0x1000>; |
| |
| interrupts-extended = <&pdc 29 IRQ_TYPE_LEVEL_HIGH>, |
| <&intc GIC_SPI 770 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", |
| "critical"; |
| |
| #qcom,sensors = <16>; |
| |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| usb_1_ss0_hsphy: phy@fd3000 { |
| compatible = "qcom,x1e80100-snps-eusb2-phy", |
| "qcom,sm8550-snps-eusb2-phy"; |
| reg = <0 0x00fd3000 0 0x154>; |
| #phy-cells = <0>; |
| |
| clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>; |
| clock-names = "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; |
| |
| status = "disabled"; |
| }; |
| |
| usb_1_ss0_qmpphy: phy@fd5000 { |
| compatible = "qcom,x1e80100-qmp-usb3-dp-phy"; |
| reg = <0 0x00fd5000 0 0x4000>; |
| |
| clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>, |
| <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; |
| clock-names = "aux", |
| "ref", |
| "com_aux", |
| "usb3_pipe"; |
| |
| power-domains = <&gcc GCC_USB_0_PHY_GDSC>; |
| |
| resets = <&gcc GCC_USB3_PHY_PRIM_BCR>, |
| <&gcc GCC_USB4_0_DP0_PHY_PRIM_BCR>; |
| reset-names = "phy", |
| "common"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <1>; |
| |
| orientation-switch; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| usb_1_ss0_qmpphy_out: endpoint { |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| usb_1_ss0_qmpphy_usb_ss_in: endpoint { |
| remote-endpoint = <&usb_1_ss0_dwc3_ss>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| usb_1_ss0_qmpphy_dp_in: endpoint { |
| remote-endpoint = <&mdss_dp0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| usb_1_ss1_hsphy: phy@fd9000 { |
| compatible = "qcom,x1e80100-snps-eusb2-phy", |
| "qcom,sm8550-snps-eusb2-phy"; |
| reg = <0 0x00fd9000 0 0x154>; |
| #phy-cells = <0>; |
| |
| clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>; |
| clock-names = "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_SEC_BCR>; |
| |
| status = "disabled"; |
| }; |
| |
| usb_1_ss1_qmpphy: phy@fda000 { |
| compatible = "qcom,x1e80100-qmp-usb3-dp-phy"; |
| reg = <0 0x00fda000 0 0x4000>; |
| |
| clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>, |
| <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; |
| clock-names = "aux", |
| "ref", |
| "com_aux", |
| "usb3_pipe"; |
| |
| power-domains = <&gcc GCC_USB_1_PHY_GDSC>; |
| |
| resets = <&gcc GCC_USB3_PHY_SEC_BCR>, |
| <&gcc GCC_USB4_1_DP0_PHY_SEC_BCR>; |
| reset-names = "phy", |
| "common"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <1>; |
| |
| orientation-switch; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| usb_1_ss1_qmpphy_out: endpoint { |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| usb_1_ss1_qmpphy_usb_ss_in: endpoint { |
| remote-endpoint = <&usb_1_ss1_dwc3_ss>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| usb_1_ss1_qmpphy_dp_in: endpoint { |
| remote-endpoint = <&mdss_dp1_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| usb_1_ss2_hsphy: phy@fde000 { |
| compatible = "qcom,x1e80100-snps-eusb2-phy", |
| "qcom,sm8550-snps-eusb2-phy"; |
| reg = <0 0x00fde000 0 0x154>; |
| #phy-cells = <0>; |
| |
| clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>; |
| clock-names = "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_TERT_BCR>; |
| |
| status = "disabled"; |
| }; |
| |
| usb_1_ss2_qmpphy: phy@fdf000 { |
| compatible = "qcom,x1e80100-qmp-usb3-dp-phy"; |
| reg = <0 0x00fdf000 0 0x4000>; |
| |
| clocks = <&gcc GCC_USB3_TERT_PHY_AUX_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_USB3_TERT_PHY_COM_AUX_CLK>, |
| <&gcc GCC_USB3_TERT_PHY_PIPE_CLK>; |
| clock-names = "aux", |
| "ref", |
| "com_aux", |
| "usb3_pipe"; |
| |
| power-domains = <&gcc GCC_USB_2_PHY_GDSC>; |
| |
| resets = <&gcc GCC_USB3_PHY_TERT_BCR>, |
| <&gcc GCC_USB4_2_DP0_PHY_TERT_BCR>; |
| reset-names = "phy", |
| "common"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <1>; |
| |
| orientation-switch; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| usb_1_ss2_qmpphy_out: endpoint { |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| usb_1_ss2_qmpphy_usb_ss_in: endpoint { |
| remote-endpoint = <&usb_1_ss2_dwc3_ss>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| usb_1_ss2_qmpphy_dp_in: endpoint { |
| remote-endpoint = <&mdss_dp2_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| cnoc_main: interconnect@1500000 { |
| compatible = "qcom,x1e80100-cnoc-main"; |
| reg = <0 0x01500000 0 0x14400>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| config_noc: interconnect@1600000 { |
| compatible = "qcom,x1e80100-cnoc-cfg"; |
| reg = <0 0x01600000 0 0x6600>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| system_noc: interconnect@1680000 { |
| compatible = "qcom,x1e80100-system-noc"; |
| reg = <0 0x01680000 0 0x1c080>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| pcie_south_anoc: interconnect@16c0000 { |
| compatible = "qcom,x1e80100-pcie-south-anoc"; |
| reg = <0 0x016c0000 0 0xd080>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| pcie_center_anoc: interconnect@16d0000 { |
| compatible = "qcom,x1e80100-pcie-center-anoc"; |
| reg = <0 0x016d0000 0 0x7000>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| aggre1_noc: interconnect@16e0000 { |
| compatible = "qcom,x1e80100-aggre1-noc"; |
| reg = <0 0x016e0000 0 0x14400>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| aggre2_noc: interconnect@1700000 { |
| compatible = "qcom,x1e80100-aggre2-noc"; |
| reg = <0 0x01700000 0 0x1c400>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| pcie_north_anoc: interconnect@1740000 { |
| compatible = "qcom,x1e80100-pcie-north-anoc"; |
| reg = <0 0x01740000 0 0x9080>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| usb_center_anoc: interconnect@1750000 { |
| compatible = "qcom,x1e80100-usb-center-anoc"; |
| reg = <0 0x01750000 0 0x8800>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| usb_north_anoc: interconnect@1760000 { |
| compatible = "qcom,x1e80100-usb-north-anoc"; |
| reg = <0 0x01760000 0 0x7080>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| usb_south_anoc: interconnect@1770000 { |
| compatible = "qcom,x1e80100-usb-south-anoc"; |
| reg = <0 0x01770000 0 0xf080>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| mmss_noc: interconnect@1780000 { |
| compatible = "qcom,x1e80100-mmss-noc"; |
| reg = <0 0x01780000 0 0x5B800>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| pcie6a: pci@1bf8000 { |
| device_type = "pci"; |
| compatible = "qcom,pcie-x1e80100"; |
| reg = <0 0x01bf8000 0 0x3000>, |
| <0 0x70000000 0 0xf20>, |
| <0 0x70000f40 0 0xa8>, |
| <0 0x70001000 0 0x1000>, |
| <0 0x70100000 0 0x100000>, |
| <0 0x01bfb000 0 0x1000>; |
| reg-names = "parf", |
| "dbi", |
| "elbi", |
| "atu", |
| "config", |
| "mhi"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges = <0x01000000 0x0 0x00000000 0x0 0x70200000 0x0 0x100000>, |
| <0x02000000 0x0 0x70300000 0x0 0x70300000 0x0 0x1d00000>; |
| bus-range = <0x00 0xff>; |
| |
| dma-coherent; |
| |
| linux,pci-domain = <6>; |
| num-lanes = <4>; |
| |
| interrupts = <GIC_SPI 773 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 774 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 837 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 838 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 839 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 842 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi0", |
| "msi1", |
| "msi2", |
| "msi3", |
| "msi4", |
| "msi5", |
| "msi6", |
| "msi7"; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &intc 0 0 0 843 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 2 &intc 0 0 0 844 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 3 &intc 0 0 0 845 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 4 &intc 0 0 0 772 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_PCIE_6A_AUX_CLK>, |
| <&gcc GCC_PCIE_6A_CFG_AHB_CLK>, |
| <&gcc GCC_PCIE_6A_MSTR_AXI_CLK>, |
| <&gcc GCC_PCIE_6A_SLV_AXI_CLK>, |
| <&gcc GCC_PCIE_6A_SLV_Q2A_AXI_CLK>, |
| <&gcc GCC_CFG_NOC_PCIE_ANOC_SOUTH_AHB_CLK>, |
| <&gcc GCC_CNOC_PCIE_SOUTH_SF_AXI_CLK>; |
| clock-names = "aux", |
| "cfg", |
| "bus_master", |
| "bus_slave", |
| "slave_q2a", |
| "noc_aggr", |
| "cnoc_sf_axi"; |
| |
| assigned-clocks = <&gcc GCC_PCIE_6A_AUX_CLK>; |
| assigned-clock-rates = <19200000>; |
| |
| interconnects = <&pcie_south_anoc MASTER_PCIE_6A QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &cnoc_main SLAVE_PCIE_6A QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "pcie-mem", |
| "cpu-pcie"; |
| |
| resets = <&gcc GCC_PCIE_6A_BCR>, |
| <&gcc GCC_PCIE_6A_LINK_DOWN_BCR>; |
| reset-names = "pci", |
| "link_down"; |
| |
| power-domains = <&gcc GCC_PCIE_6A_GDSC>; |
| required-opps = <&rpmhpd_opp_nom>; |
| |
| phys = <&pcie6a_phy>; |
| phy-names = "pciephy"; |
| |
| status = "disabled"; |
| }; |
| |
| pcie6a_phy: phy@1bfc000 { |
| compatible = "qcom,x1e80100-qmp-gen4x4-pcie-phy"; |
| reg = <0 0x01bfc000 0 0x2000>, |
| <0 0x01bfe000 0 0x2000>; |
| |
| clocks = <&gcc GCC_PCIE_6A_PHY_AUX_CLK>, |
| <&gcc GCC_PCIE_6A_CFG_AHB_CLK>, |
| <&tcsr TCSR_PCIE_4L_CLKREF_EN>, |
| <&gcc GCC_PCIE_6A_PHY_RCHNG_CLK>, |
| <&gcc GCC_PCIE_6A_PIPE_CLK>, |
| <&gcc GCC_PCIE_6A_PIPEDIV2_CLK>; |
| clock-names = "aux", |
| "cfg_ahb", |
| "ref", |
| "rchng", |
| "pipe", |
| "pipediv2"; |
| |
| resets = <&gcc GCC_PCIE_6A_PHY_BCR>, |
| <&gcc GCC_PCIE_6A_NOCSR_COM_PHY_BCR>; |
| reset-names = "phy", |
| "phy_nocsr"; |
| |
| assigned-clocks = <&gcc GCC_PCIE_6A_PHY_RCHNG_CLK>; |
| assigned-clock-rates = <100000000>; |
| |
| power-domains = <&gcc GCC_PCIE_6_PHY_GDSC>; |
| |
| qcom,4ln-config-sel = <&tcsr 0x1a000 0>; |
| |
| #clock-cells = <0>; |
| clock-output-names = "pcie6a_pipe_clk"; |
| |
| #phy-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| pcie5: pci@1c00000 { |
| device_type = "pci"; |
| compatible = "qcom,pcie-x1e80100"; |
| reg = <0 0x01c00000 0 0x3000>, |
| <0 0x7e000000 0 0xf1d>, |
| <0 0x7e000f40 0 0xa8>, |
| <0 0x7e001000 0 0x1000>, |
| <0 0x7e100000 0 0x100000>, |
| <0 0x01c03000 0 0x1000>; |
| reg-names = "parf", |
| "dbi", |
| "elbi", |
| "atu", |
| "config", |
| "mhi"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges = <0x01000000 0x0 0x00000000 0x0 0x7e200000 0x0 0x100000>, |
| <0x02000000 0x0 0x7e300000 0x0 0x7e300000 0x0 0x1d00000>; |
| bus-range = <0x00 0xff>; |
| |
| dma-coherent; |
| |
| linux,pci-domain = <5>; |
| num-lanes = <2>; |
| |
| interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi0", |
| "msi1", |
| "msi2", |
| "msi3", |
| "msi4", |
| "msi5", |
| "msi6", |
| "msi7"; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &intc 0 0 0 70 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 2 &intc 0 0 0 71 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 3 &intc 0 0 0 72 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 4 &intc 0 0 0 73 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_PCIE_5_AUX_CLK>, |
| <&gcc GCC_PCIE_5_CFG_AHB_CLK>, |
| <&gcc GCC_PCIE_5_MSTR_AXI_CLK>, |
| <&gcc GCC_PCIE_5_SLV_AXI_CLK>, |
| <&gcc GCC_PCIE_5_SLV_Q2A_AXI_CLK>, |
| <&gcc GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK>, |
| <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>; |
| clock-names = "aux", |
| "cfg", |
| "bus_master", |
| "bus_slave", |
| "slave_q2a", |
| "noc_aggr", |
| "cnoc_sf_axi"; |
| |
| assigned-clocks = <&gcc GCC_PCIE_5_AUX_CLK>; |
| assigned-clock-rates = <19200000>; |
| |
| interconnects = <&pcie_north_anoc MASTER_PCIE_5 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &cnoc_main SLAVE_PCIE_5 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "pcie-mem", |
| "cpu-pcie"; |
| |
| resets = <&gcc GCC_PCIE_5_BCR>, |
| <&gcc GCC_PCIE_5_LINK_DOWN_BCR>; |
| reset-names = "pci", |
| "link_down"; |
| |
| power-domains = <&gcc GCC_PCIE_5_GDSC>; |
| required-opps = <&rpmhpd_opp_nom>; |
| |
| phys = <&pcie5_phy>; |
| phy-names = "pciephy"; |
| |
| status = "disabled"; |
| }; |
| |
| pcie5_phy: phy@1c06000 { |
| compatible = "qcom,x1e80100-qmp-gen3x2-pcie-phy"; |
| reg = <0 0x01c06000 0 0x2000>; |
| |
| clocks = <&gcc GCC_PCIE_5_AUX_CLK>, |
| <&gcc GCC_PCIE_5_CFG_AHB_CLK>, |
| <&tcsr TCSR_PCIE_2L_5_CLKREF_EN>, |
| <&gcc GCC_PCIE_5_PHY_RCHNG_CLK>, |
| <&gcc GCC_PCIE_5_PIPE_CLK>, |
| <&gcc GCC_PCIE_5_PIPEDIV2_CLK>; |
| clock-names = "aux", |
| "cfg_ahb", |
| "ref", |
| "rchng", |
| "pipe", |
| "pipediv2"; |
| |
| resets = <&gcc GCC_PCIE_5_PHY_BCR>; |
| reset-names = "phy"; |
| |
| assigned-clocks = <&gcc GCC_PCIE_5_PHY_RCHNG_CLK>; |
| assigned-clock-rates = <100000000>; |
| |
| power-domains = <&gcc GCC_PCIE_5_PHY_GDSC>; |
| |
| #clock-cells = <0>; |
| clock-output-names = "pcie5_pipe_clk"; |
| |
| #phy-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| pcie4: pci@1c08000 { |
| device_type = "pci"; |
| compatible = "qcom,pcie-x1e80100"; |
| reg = <0 0x01c08000 0 0x3000>, |
| <0 0x7c000000 0 0xf1d>, |
| <0 0x7c000f40 0 0xa8>, |
| <0 0x7c001000 0 0x1000>, |
| <0 0x7c100000 0 0x100000>, |
| <0 0x01c0b000 0 0x1000>; |
| reg-names = "parf", |
| "dbi", |
| "elbi", |
| "atu", |
| "config", |
| "mhi"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges = <0x01000000 0x0 0x00000000 0x0 0x7c200000 0x0 0x100000>, |
| <0x02000000 0x0 0x7c300000 0x0 0x7c300000 0x0 0x1d00000>; |
| bus-range = <0x00 0xff>; |
| |
| dma-coherent; |
| |
| linux,pci-domain = <4>; |
| num-lanes = <2>; |
| |
| interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi0", |
| "msi1", |
| "msi2", |
| "msi3", |
| "msi4", |
| "msi5", |
| "msi6", |
| "msi7"; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GCC_PCIE_4_AUX_CLK>, |
| <&gcc GCC_PCIE_4_CFG_AHB_CLK>, |
| <&gcc GCC_PCIE_4_MSTR_AXI_CLK>, |
| <&gcc GCC_PCIE_4_SLV_AXI_CLK>, |
| <&gcc GCC_PCIE_4_SLV_Q2A_AXI_CLK>, |
| <&gcc GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK>, |
| <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>; |
| clock-names = "aux", |
| "cfg", |
| "bus_master", |
| "bus_slave", |
| "slave_q2a", |
| "noc_aggr", |
| "cnoc_sf_axi"; |
| |
| assigned-clocks = <&gcc GCC_PCIE_4_AUX_CLK>; |
| assigned-clock-rates = <19200000>; |
| |
| interconnects = <&pcie_north_anoc MASTER_PCIE_4 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &cnoc_main SLAVE_PCIE_4 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "pcie-mem", |
| "cpu-pcie"; |
| |
| resets = <&gcc GCC_PCIE_4_BCR>, |
| <&gcc GCC_PCIE_4_LINK_DOWN_BCR>; |
| reset-names = "pci", |
| "link_down"; |
| |
| power-domains = <&gcc GCC_PCIE_4_GDSC>; |
| required-opps = <&rpmhpd_opp_nom>; |
| |
| phys = <&pcie4_phy>; |
| phy-names = "pciephy"; |
| |
| status = "disabled"; |
| |
| pcie4_port0: pcie@0 { |
| device_type = "pci"; |
| reg = <0x0 0x0 0x0 0x0 0x0>; |
| bus-range = <0x01 0xff>; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| }; |
| }; |
| |
| pcie4_phy: phy@1c0e000 { |
| compatible = "qcom,x1e80100-qmp-gen3x2-pcie-phy"; |
| reg = <0 0x01c0e000 0 0x2000>; |
| |
| clocks = <&gcc GCC_PCIE_4_AUX_CLK>, |
| <&gcc GCC_PCIE_4_CFG_AHB_CLK>, |
| <&tcsr TCSR_PCIE_2L_4_CLKREF_EN>, |
| <&gcc GCC_PCIE_4_PHY_RCHNG_CLK>, |
| <&gcc GCC_PCIE_4_PIPE_CLK>, |
| <&gcc GCC_PCIE_4_PIPEDIV2_CLK>; |
| clock-names = "aux", |
| "cfg_ahb", |
| "ref", |
| "rchng", |
| "pipe", |
| "pipediv2"; |
| |
| resets = <&gcc GCC_PCIE_4_PHY_BCR>; |
| reset-names = "phy"; |
| |
| assigned-clocks = <&gcc GCC_PCIE_4_PHY_RCHNG_CLK>; |
| assigned-clock-rates = <100000000>; |
| |
| power-domains = <&gcc GCC_PCIE_4_PHY_GDSC>; |
| |
| #clock-cells = <0>; |
| clock-output-names = "pcie4_pipe_clk"; |
| |
| #phy-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| tcsr_mutex: hwlock@1f40000 { |
| compatible = "qcom,tcsr-mutex"; |
| reg = <0 0x01f40000 0 0x20000>; |
| #hwlock-cells = <1>; |
| }; |
| |
| tcsr: clock-controller@1fc0000 { |
| compatible = "qcom,x1e80100-tcsr", "syscon"; |
| reg = <0 0x01fc0000 0 0x30000>; |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| gpu: gpu@3d00000 { |
| compatible = "qcom,adreno-43050c01", "qcom,adreno"; |
| reg = <0x0 0x03d00000 0x0 0x40000>, |
| <0x0 0x03d9e000 0x0 0x1000>, |
| <0x0 0x03d61000 0x0 0x800>; |
| |
| reg-names = "kgsl_3d0_reg_memory", |
| "cx_mem", |
| "cx_dbgc"; |
| |
| interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; |
| |
| iommus = <&adreno_smmu 0 0x0>, |
| <&adreno_smmu 1 0x0>; |
| |
| operating-points-v2 = <&gpu_opp_table>; |
| |
| qcom,gmu = <&gmu>; |
| #cooling-cells = <2>; |
| |
| interconnects = <&gem_noc MASTER_GFX3D 0 &mc_virt SLAVE_EBI1 0>; |
| interconnect-names = "gfx-mem"; |
| |
| status = "disabled"; |
| |
| zap-shader { |
| memory-region = <&gpu_microcode_mem>; |
| }; |
| |
| gpu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-1100000000 { |
| opp-hz = /bits/ 64 <1100000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; |
| opp-peak-kBps = <16500000>; |
| }; |
| |
| opp-1000000000 { |
| opp-hz = /bits/ 64 <1000000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; |
| opp-peak-kBps = <14398438>; |
| }; |
| |
| opp-925000000 { |
| opp-hz = /bits/ 64 <925000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; |
| opp-peak-kBps = <14398438>; |
| }; |
| |
| opp-800000000 { |
| opp-hz = /bits/ 64 <800000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM>; |
| opp-peak-kBps = <12449219>; |
| }; |
| |
| opp-744000000 { |
| opp-hz = /bits/ 64 <744000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>; |
| opp-peak-kBps = <10687500>; |
| }; |
| |
| opp-687000000 { |
| opp-hz = /bits/ 64 <687000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; |
| opp-peak-kBps = <8171875>; |
| }; |
| |
| opp-550000000 { |
| opp-hz = /bits/ 64 <550000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS>; |
| opp-peak-kBps = <6074219>; |
| }; |
| |
| opp-390000000 { |
| opp-hz = /bits/ 64 <390000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; |
| opp-peak-kBps = <3000000>; |
| }; |
| |
| opp-300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>; |
| opp-peak-kBps = <2136719>; |
| }; |
| }; |
| }; |
| |
| gmu: gmu@3d6a000 { |
| compatible = "qcom,adreno-gmu-x185.1", "qcom,adreno-gmu"; |
| reg = <0x0 0x03d6a000 0x0 0x35000>, |
| <0x0 0x03d50000 0x0 0x10000>, |
| <0x0 0x0b280000 0x0 0x10000>; |
| reg-names = "gmu", "rscc", "gmu_pdc"; |
| |
| interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hfi", "gmu"; |
| |
| clocks = <&gpucc GPU_CC_AHB_CLK>, |
| <&gpucc GPU_CC_CX_GMU_CLK>, |
| <&gpucc GPU_CC_CXO_CLK>, |
| <&gcc GCC_DDRSS_GPU_AXI_CLK>, |
| <&gcc GCC_GPU_MEMNOC_GFX_CLK>, |
| <&gpucc GPU_CC_HUB_CX_INT_CLK>, |
| <&gpucc GPU_CC_DEMET_CLK>; |
| clock-names = "ahb", |
| "gmu", |
| "cxo", |
| "axi", |
| "memnoc", |
| "hub", |
| "demet"; |
| |
| power-domains = <&gpucc GPU_CX_GDSC>, |
| <&gpucc GPU_GX_GDSC>; |
| power-domain-names = "cx", |
| "gx"; |
| |
| iommus = <&adreno_smmu 5 0x0>; |
| |
| qcom,qmp = <&aoss_qmp>; |
| |
| operating-points-v2 = <&gmu_opp_table>; |
| |
| gmu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-550000000 { |
| opp-hz = /bits/ 64 <550000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS>; |
| }; |
| |
| opp-220000000 { |
| opp-hz = /bits/ 64 <220000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; |
| }; |
| }; |
| }; |
| |
| gpucc: clock-controller@3d90000 { |
| compatible = "qcom,x1e80100-gpucc"; |
| reg = <0 0x03d90000 0 0xa000>; |
| clocks = <&bi_tcxo_div2>, |
| <&gcc GCC_GPU_GPLL0_CPH_CLK_SRC>, |
| <&gcc GCC_GPU_GPLL0_DIV_CPH_CLK_SRC>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| }; |
| |
| adreno_smmu: iommu@3da0000 { |
| compatible = "qcom,x1e80100-smmu-500", "qcom,adreno-smmu", |
| "qcom,smmu-500", "arm,mmu-500"; |
| reg = <0x0 0x03da0000 0x0 0x40000>; |
| #iommu-cells = <2>; |
| #global-interrupts = <1>; |
| interrupts = <GIC_SPI 674 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 678 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 679 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 680 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 686 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 687 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 688 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 476 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 574 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 575 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 576 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 577 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 660 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 662 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 665 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 666 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 667 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 669 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 670 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 700 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gpucc GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK>, |
| <&gcc GCC_GPU_MEMNOC_GFX_CLK>, |
| <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>, |
| <&gpucc GPU_CC_AHB_CLK>; |
| clock-names = "hlos", |
| "bus", |
| "iface", |
| "ahb"; |
| power-domains = <&gpucc GPU_CX_GDSC>; |
| dma-coherent; |
| }; |
| |
| gem_noc: interconnect@26400000 { |
| compatible = "qcom,x1e80100-gem-noc"; |
| reg = <0 0x26400000 0 0x311200>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| nsp_noc: interconnect@320c0000 { |
| compatible = "qcom,x1e80100-nsp-noc"; |
| reg = <0 0x320C0000 0 0xe080>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| lpass_wsa2macro: codec@6aa0000 { |
| compatible = "qcom,x1e80100-lpass-wsa-macro", "qcom,sm8550-lpass-wsa-macro"; |
| reg = <0 0x06aa0000 0 0x1000>; |
| clocks = <&q6prmcc LPASS_CLK_ID_WSA2_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&lpass_vamacro>; |
| clock-names = "mclk", |
| "macro", |
| "dcodec", |
| "fsgen"; |
| |
| #clock-cells = <0>; |
| clock-output-names = "wsa2-mclk"; |
| #sound-dai-cells = <1>; |
| sound-name-prefix = "WSA2"; |
| }; |
| |
| swr3: soundwire@6ab0000 { |
| compatible = "qcom,soundwire-v2.0.0"; |
| reg = <0 0x06ab0000 0 0x10000>; |
| clocks = <&lpass_wsa2macro>; |
| clock-names = "iface"; |
| interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>; |
| label = "WSA2"; |
| |
| pinctrl-0 = <&wsa2_swr_active>; |
| pinctrl-names = "default"; |
| resets = <&lpass_audiocc LPASS_AUDIO_SWR_WSA2_CGCR>; |
| reset-names = "swr_audio_cgcr"; |
| |
| qcom,din-ports = <4>; |
| qcom,dout-ports = <9>; |
| |
| qcom,ports-sinterval = /bits/ 16 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0xc8 0xff 0xff 0x0f 0x0f 0xff 0x31f>; |
| qcom,ports-offset1 = /bits/ 8 <0x01 0x03 0x05 0x02 0x04 0x15 0x00 0xff 0xff 0x06 0x0d 0xff 0x00>; |
| qcom,ports-offset2 = /bits/ 8 <0xff 0x07 0x1f 0xff 0x07 0x1f 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>; |
| qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>; |
| qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x18>; |
| qcom,ports-block-pack-mode = /bits/ 8 <0x00 0x01 0x01 0x00 0x01 0x01 0x00 0x00 0x00 0x01 0x01 0x00 0x00>; |
| qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| |
| #address-cells = <2>; |
| #size-cells = <0>; |
| #sound-dai-cells = <1>; |
| status = "disabled"; |
| }; |
| |
| lpass_rxmacro: codec@6ac0000 { |
| compatible = "qcom,x1e80100-lpass-rx-macro", "qcom,sm8550-lpass-rx-macro"; |
| reg = <0 0x06ac0000 0 0x1000>; |
| clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&lpass_vamacro>; |
| clock-names = "mclk", |
| "macro", |
| "dcodec", |
| "fsgen"; |
| |
| #clock-cells = <0>; |
| clock-output-names = "mclk"; |
| #sound-dai-cells = <1>; |
| }; |
| |
| swr1: soundwire@6ad0000 { |
| compatible = "qcom,soundwire-v2.0.0"; |
| reg = <0 0x06ad0000 0 0x10000>; |
| clocks = <&lpass_rxmacro>; |
| clock-names = "iface"; |
| interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; |
| label = "RX"; |
| |
| pinctrl-0 = <&rx_swr_active>; |
| pinctrl-names = "default"; |
| |
| resets = <&lpass_audiocc LPASS_AUDIO_SWR_RX_CGCR>; |
| reset-names = "swr_audio_cgcr"; |
| qcom,din-ports = <1>; |
| qcom,dout-ports = <11>; |
| |
| qcom,ports-sinterval = /bits/ 16 <0x03 0x1f 0x1f 0x07 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0b 0x01 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0b 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-hstart = /bits/ 8 <0xff 0x03 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-hstop = /bits/ 8 <0xff 0x06 0x0f 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0x01 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| |
| #address-cells = <2>; |
| #size-cells = <0>; |
| #sound-dai-cells = <1>; |
| status = "disabled"; |
| }; |
| |
| lpass_txmacro: codec@6ae0000 { |
| compatible = "qcom,x1e80100-lpass-tx-macro", "qcom,sm8550-lpass-tx-macro"; |
| reg = <0 0x06ae0000 0 0x1000>; |
| clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&lpass_vamacro>; |
| clock-names = "mclk", |
| "macro", |
| "dcodec", |
| "fsgen"; |
| |
| #clock-cells = <0>; |
| clock-output-names = "mclk"; |
| #sound-dai-cells = <1>; |
| }; |
| |
| lpass_wsamacro: codec@6b00000 { |
| compatible = "qcom,x1e80100-lpass-wsa-macro", "qcom,sm8550-lpass-wsa-macro"; |
| reg = <0 0x06b00000 0 0x1000>; |
| clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&lpass_vamacro>; |
| clock-names = "mclk", |
| "macro", |
| "dcodec", |
| "fsgen"; |
| |
| #clock-cells = <0>; |
| clock-output-names = "mclk"; |
| #sound-dai-cells = <1>; |
| sound-name-prefix = "WSA"; |
| }; |
| |
| swr0: soundwire@6b10000 { |
| compatible = "qcom,soundwire-v2.0.0"; |
| reg = <0 0x06b10000 0 0x10000>; |
| clocks = <&lpass_wsamacro>; |
| clock-names = "iface"; |
| interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; |
| label = "WSA"; |
| |
| pinctrl-0 = <&wsa_swr_active>; |
| pinctrl-names = "default"; |
| resets = <&lpass_audiocc LPASS_AUDIO_SWR_WSA_CGCR>; |
| reset-names = "swr_audio_cgcr"; |
| |
| qcom,din-ports = <4>; |
| qcom,dout-ports = <9>; |
| |
| qcom,ports-sinterval = /bits/ 16 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0xc8 0xff 0xff 0x0f 0x0f 0xff 0x31f>; |
| qcom,ports-offset1 = /bits/ 8 <0x01 0x03 0x05 0x02 0x04 0x15 0x00 0xff 0xff 0x06 0x0d 0xff 0x00>; |
| qcom,ports-offset2 = /bits/ 8 <0xff 0x07 0x1f 0xff 0x07 0x1f 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>; |
| qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>; |
| qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x18>; |
| qcom,ports-block-pack-mode = /bits/ 8 <0x00 0x01 0x01 0x00 0x01 0x01 0x00 0x00 0x00 0x01 0x01 0x00 0x00>; |
| qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>; |
| |
| #address-cells = <2>; |
| #size-cells = <0>; |
| #sound-dai-cells = <1>; |
| status = "disabled"; |
| }; |
| |
| lpass_audiocc: clock-controller@6b6c000 { |
| compatible = "qcom,x1e80100-lpassaudiocc", "qcom,sc8280xp-lpassaudiocc"; |
| reg = <0 0x06b6c000 0 0x1000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| swr2: soundwire@6d30000 { |
| compatible = "qcom,soundwire-v2.0.0"; |
| reg = <0 0x06d30000 0 0x10000>; |
| clocks = <&lpass_txmacro>; |
| clock-names = "iface"; |
| interrupts = <GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "core", "wakeup"; |
| label = "TX"; |
| resets = <&lpasscc LPASS_AUDIO_SWR_TX_CGCR>; |
| reset-names = "swr_audio_cgcr"; |
| |
| pinctrl-0 = <&tx_swr_active>; |
| pinctrl-names = "default"; |
| |
| qcom,din-ports = <4>; |
| qcom,dout-ports = <1>; |
| |
| qcom,ports-sinterval-low = /bits/ 8 <0x00 0x01 0x03 0x03 0x00>; |
| qcom,ports-offset1 = /bits/ 8 <0x00 0x01 0x02 0x00 0x00>; |
| qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x00 0x00 0xff>; |
| qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff>; |
| qcom,ports-lane-control = /bits/ 8 <0xff 0x00 0x00 0x01 0xff>; |
| |
| #address-cells = <2>; |
| #size-cells = <0>; |
| #sound-dai-cells = <1>; |
| status = "disabled"; |
| }; |
| |
| lpass_vamacro: codec@6d44000 { |
| compatible = "qcom,x1e80100-lpass-va-macro", "qcom,sm8550-lpass-va-macro"; |
| reg = <0 0x06d44000 0 0x1000>; |
| clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>; |
| clock-names = "mclk", |
| "macro", |
| "dcodec"; |
| |
| #clock-cells = <0>; |
| clock-output-names = "fsgen"; |
| #sound-dai-cells = <1>; |
| }; |
| |
| lpass_tlmm: pinctrl@6e80000 { |
| compatible = "qcom,x1e80100-lpass-lpi-pinctrl", "qcom,sm8550-lpass-lpi-pinctrl"; |
| reg = <0 0x06e80000 0 0x20000>, |
| <0 0x07250000 0 0x10000>; |
| |
| clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, |
| <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>; |
| clock-names = "core", "audio"; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&lpass_tlmm 0 0 23>; |
| |
| tx_swr_active: tx-swr-active-state { |
| clk-pins { |
| pins = "gpio0"; |
| function = "swr_tx_clk"; |
| drive-strength = <2>; |
| slew-rate = <1>; |
| bias-disable; |
| }; |
| |
| data-pins { |
| pins = "gpio1", "gpio2"; |
| function = "swr_tx_data"; |
| drive-strength = <2>; |
| slew-rate = <1>; |
| bias-bus-hold; |
| }; |
| }; |
| |
| rx_swr_active: rx-swr-active-state { |
| clk-pins { |
| pins = "gpio3"; |
| function = "swr_rx_clk"; |
| drive-strength = <2>; |
| slew-rate = <1>; |
| bias-disable; |
| }; |
| |
| data-pins { |
| pins = "gpio4", "gpio5"; |
| function = "swr_rx_data"; |
| drive-strength = <2>; |
| slew-rate = <1>; |
| bias-bus-hold; |
| }; |
| }; |
| |
| dmic01_default: dmic01-default-state { |
| clk-pins { |
| pins = "gpio6"; |
| function = "dmic1_clk"; |
| drive-strength = <8>; |
| output-high; |
| }; |
| |
| data-pins { |
| pins = "gpio7"; |
| function = "dmic1_data"; |
| drive-strength = <8>; |
| input-enable; |
| }; |
| }; |
| |
| dmic23_default: dmic23-default-state { |
| clk-pins { |
| pins = "gpio8"; |
| function = "dmic2_clk"; |
| drive-strength = <8>; |
| output-high; |
| }; |
| |
| data-pins { |
| pins = "gpio9"; |
| function = "dmic2_data"; |
| drive-strength = <8>; |
| input-enable; |
| }; |
| }; |
| |
| wsa_swr_active: wsa-swr-active-state { |
| clk-pins { |
| pins = "gpio10"; |
| function = "wsa_swr_clk"; |
| drive-strength = <2>; |
| slew-rate = <1>; |
| bias-disable; |
| }; |
| |
| data-pins { |
| pins = "gpio11"; |
| function = "wsa_swr_data"; |
| drive-strength = <2>; |
| slew-rate = <1>; |
| bias-bus-hold; |
| }; |
| }; |
| |
| wsa2_swr_active: wsa2-swr-active-state { |
| clk-pins { |
| pins = "gpio15"; |
| function = "wsa2_swr_clk"; |
| drive-strength = <2>; |
| slew-rate = <1>; |
| bias-disable; |
| }; |
| |
| data-pins { |
| pins = "gpio16"; |
| function = "wsa2_swr_data"; |
| drive-strength = <2>; |
| slew-rate = <1>; |
| bias-bus-hold; |
| }; |
| }; |
| }; |
| |
| lpasscc: clock-controller@6ea0000 { |
| compatible = "qcom,x1e80100-lpasscc", "qcom,sc8280xp-lpasscc"; |
| reg = <0 0x06ea0000 0 0x12000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| lpass_ag_noc: interconnect@7e40000 { |
| compatible = "qcom,x1e80100-lpass-ag-noc"; |
| reg = <0 0x07e40000 0 0xe080>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| lpass_lpiaon_noc: interconnect@7400000 { |
| compatible = "qcom,x1e80100-lpass-lpiaon-noc"; |
| reg = <0 0x07400000 0 0x19080>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| lpass_lpicx_noc: interconnect@7430000 { |
| compatible = "qcom,x1e80100-lpass-lpicx-noc"; |
| reg = <0 0x07430000 0 0x3A200>; |
| |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| |
| #interconnect-cells = <2>; |
| }; |
| |
| usb_2_hsphy: phy@88e0000 { |
| compatible = "qcom,x1e80100-snps-eusb2-phy", |
| "qcom,sm8550-snps-eusb2-phy"; |
| reg = <0 0x088e0000 0 0x154>; |
| #phy-cells = <0>; |
| |
| clocks = <&tcsr TCSR_USB2_2_CLKREF_EN>; |
| clock-names = "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_USB20_HS_BCR>; |
| |
| status = "disabled"; |
| }; |
| |
| usb_mp_hsphy0: phy@88e1000 { |
| compatible = "qcom,x1e80100-snps-eusb2-phy", |
| "qcom,sm8550-snps-eusb2-phy"; |
| reg = <0 0x088e1000 0 0x154>; |
| #phy-cells = <0>; |
| |
| clocks = <&tcsr TCSR_USB3_MP0_CLKREF_EN>; |
| clock-names = "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_HS0_MP_BCR>; |
| |
| status = "disabled"; |
| }; |
| |
| usb_mp_hsphy1: phy@88e2000 { |
| compatible = "qcom,x1e80100-snps-eusb2-phy", |
| "qcom,sm8550-snps-eusb2-phy"; |
| reg = <0 0x088e2000 0 0x154>; |
| #phy-cells = <0>; |
| |
| clocks = <&tcsr TCSR_USB3_MP1_CLKREF_EN>; |
| clock-names = "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_HS1_MP_BCR>; |
| |
| status = "disabled"; |
| }; |
| |
| usb_mp_qmpphy0: phy@88e3000 { |
| compatible = "qcom,x1e80100-qmp-usb3-uni-phy"; |
| reg = <0 0x088e3000 0 0x2000>; |
| |
| clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>, |
| <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>; |
| clock-names = "aux", |
| "ref", |
| "com_aux", |
| "pipe"; |
| |
| resets = <&gcc GCC_USB3_UNIPHY_MP0_BCR>, |
| <&gcc GCC_USB3UNIPHY_PHY_MP0_BCR>; |
| reset-names = "phy", |
| "phy_phy"; |
| |
| power-domains = <&gcc GCC_USB3_MP_SS0_PHY_GDSC>; |
| |
| #clock-cells = <0>; |
| clock-output-names = "usb_mp_phy0_pipe_clk"; |
| |
| #phy-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| usb_mp_qmpphy1: phy@88e5000 { |
| compatible = "qcom,x1e80100-qmp-usb3-uni-phy"; |
| reg = <0 0x088e5000 0 0x2000>; |
| |
| clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>, |
| <&gcc GCC_USB3_MP_PHY_PIPE_1_CLK>; |
| clock-names = "aux", |
| "ref", |
| "com_aux", |
| "pipe"; |
| |
| resets = <&gcc GCC_USB3_UNIPHY_MP1_BCR>, |
| <&gcc GCC_USB3UNIPHY_PHY_MP1_BCR>; |
| reset-names = "phy", |
| "phy_phy"; |
| |
| power-domains = <&gcc GCC_USB3_MP_SS1_PHY_GDSC>; |
| |
| #clock-cells = <0>; |
| clock-output-names = "usb_mp_phy1_pipe_clk"; |
| |
| #phy-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| usb_1_ss2: usb@a0f8800 { |
| compatible = "qcom,x1e80100-dwc3", "qcom,dwc3"; |
| reg = <0 0x0a0f8800 0 0x400>; |
| |
| clocks = <&gcc GCC_CFG_NOC_USB3_TERT_AXI_CLK>, |
| <&gcc GCC_USB30_TERT_MASTER_CLK>, |
| <&gcc GCC_AGGRE_USB3_TERT_AXI_CLK>, |
| <&gcc GCC_USB30_TERT_SLEEP_CLK>, |
| <&gcc GCC_USB30_TERT_MOCK_UTMI_CLK>, |
| <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>, |
| <&gcc GCC_AGGRE_NOC_USB_NORTH_AXI_CLK>, |
| <&gcc GCC_AGGRE_NOC_USB_SOUTH_AXI_CLK>, |
| <&gcc GCC_SYS_NOC_USB_AXI_CLK>; |
| clock-names = "cfg_noc", |
| "core", |
| "iface", |
| "sleep", |
| "mock_utmi", |
| "noc_aggr", |
| "noc_aggr_north", |
| "noc_aggr_south", |
| "noc_sys"; |
| |
| assigned-clocks = <&gcc GCC_USB30_TERT_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB30_TERT_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, |
| <200000000>; |
| |
| interrupts-extended = <&intc GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>, |
| <&pdc 58 IRQ_TYPE_EDGE_BOTH>, |
| <&pdc 57 IRQ_TYPE_EDGE_BOTH>, |
| <&pdc 10 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "pwr_event", |
| "dp_hs_phy_irq", |
| "dm_hs_phy_irq", |
| "ss_phy_irq"; |
| |
| power-domains = <&gcc GCC_USB30_TERT_GDSC>; |
| required-opps = <&rpmhpd_opp_nom>; |
| |
| resets = <&gcc GCC_USB30_TERT_BCR>; |
| |
| interconnects = <&usb_south_anoc MASTER_USB3_2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_USB3_2 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "usb-ddr", |
| "apps-usb"; |
| |
| wakeup-source; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| status = "disabled"; |
| |
| usb_1_ss2_dwc3: usb@a000000 { |
| compatible = "snps,dwc3"; |
| reg = <0 0x0a000000 0 0xcd00>; |
| |
| interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; |
| |
| iommus = <&apps_smmu 0x14a0 0x0>; |
| |
| phys = <&usb_1_ss2_hsphy>, |
| <&usb_1_ss2_qmpphy QMP_USB43DP_USB3_PHY>; |
| phy-names = "usb2-phy", |
| "usb3-phy"; |
| |
| snps,dis_u2_susphy_quirk; |
| snps,dis_enblslpm_quirk; |
| snps,usb3_lpm_capable; |
| |
| dma-coherent; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| usb_1_ss2_dwc3_hs: endpoint { |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| usb_1_ss2_dwc3_ss: endpoint { |
| remote-endpoint = <&usb_1_ss2_qmpphy_usb_ss_in>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| usb_2: usb@a2f8800 { |
| compatible = "qcom,x1e80100-dwc3", "qcom,dwc3"; |
| reg = <0 0x0a2f8800 0 0x400>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| clocks = <&gcc GCC_CFG_NOC_USB2_PRIM_AXI_CLK>, |
| <&gcc GCC_USB20_MASTER_CLK>, |
| <&gcc GCC_AGGRE_USB2_PRIM_AXI_CLK>, |
| <&gcc GCC_USB20_SLEEP_CLK>, |
| <&gcc GCC_USB20_MOCK_UTMI_CLK>, |
| <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>, |
| <&gcc GCC_AGGRE_NOC_USB_NORTH_AXI_CLK>, |
| <&gcc GCC_AGGRE_NOC_USB_SOUTH_AXI_CLK>, |
| <&gcc GCC_SYS_NOC_USB_AXI_CLK>; |
| clock-names = "cfg_noc", |
| "core", |
| "iface", |
| "sleep", |
| "mock_utmi", |
| "noc_aggr", |
| "noc_aggr_north", |
| "noc_aggr_south", |
| "noc_sys"; |
| |
| assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB20_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, <200000000>; |
| |
| interrupts-extended = <&intc GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>, |
| <&pdc 50 IRQ_TYPE_EDGE_BOTH>, |
| <&pdc 49 IRQ_TYPE_EDGE_BOTH>; |
| interrupt-names = "pwr_event", |
| "dp_hs_phy_irq", |
| "dm_hs_phy_irq"; |
| |
| power-domains = <&gcc GCC_USB20_PRIM_GDSC>; |
| required-opps = <&rpmhpd_opp_nom>; |
| |
| resets = <&gcc GCC_USB20_PRIM_BCR>; |
| |
| interconnects = <&usb_north_anoc MASTER_USB2 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_USB2 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "usb-ddr", |
| "apps-usb"; |
| |
| wakeup-source; |
| |
| status = "disabled"; |
| |
| usb_2_dwc3: usb@a200000 { |
| compatible = "snps,dwc3"; |
| reg = <0 0x0a200000 0 0xcd00>; |
| interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>; |
| iommus = <&apps_smmu 0x14e0 0x0>; |
| phys = <&usb_2_hsphy>; |
| phy-names = "usb2-phy"; |
| maximum-speed = "high-speed"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| usb_2_dwc3_hs: endpoint { |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| usb_mp: usb@a4f8800 { |
| compatible = "qcom,x1e80100-dwc3-mp", "qcom,dwc3"; |
| reg = <0 0x0a4f8800 0 0x400>; |
| |
| clocks = <&gcc GCC_CFG_NOC_USB3_MP_AXI_CLK>, |
| <&gcc GCC_USB30_MP_MASTER_CLK>, |
| <&gcc GCC_AGGRE_USB3_MP_AXI_CLK>, |
| <&gcc GCC_USB30_MP_SLEEP_CLK>, |
| <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>, |
| <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>, |
| <&gcc GCC_AGGRE_NOC_USB_NORTH_AXI_CLK>, |
| <&gcc GCC_AGGRE_NOC_USB_SOUTH_AXI_CLK>, |
| <&gcc GCC_SYS_NOC_USB_AXI_CLK>; |
| clock-names = "cfg_noc", |
| "core", |
| "iface", |
| "sleep", |
| "mock_utmi", |
| "noc_aggr", |
| "noc_aggr_north", |
| "noc_aggr_south", |
| "noc_sys"; |
| |
| assigned-clocks = <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB30_MP_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, |
| <200000000>; |
| |
| interrupts-extended = <&intc GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, |
| <&intc GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>, |
| <&intc GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>, |
| <&intc GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>, |
| <&pdc 52 IRQ_TYPE_EDGE_BOTH>, |
| <&pdc 51 IRQ_TYPE_EDGE_BOTH>, |
| <&pdc 54 IRQ_TYPE_EDGE_BOTH>, |
| <&pdc 53 IRQ_TYPE_EDGE_BOTH>, |
| <&pdc 55 IRQ_TYPE_LEVEL_HIGH>, |
| <&pdc 56 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "pwr_event_1", "pwr_event_2", |
| "hs_phy_1", "hs_phy_2", |
| "dp_hs_phy_1", "dm_hs_phy_1", |
| "dp_hs_phy_2", "dm_hs_phy_2", |
| "ss_phy_1", "ss_phy_2"; |
| |
| power-domains = <&gcc GCC_USB30_MP_GDSC>; |
| required-opps = <&rpmhpd_opp_nom>; |
| |
| resets = <&gcc GCC_USB30_MP_BCR>; |
| |
| interconnects = <&usb_north_anoc MASTER_USB3_MP QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_USB3_MP QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "usb-ddr", |
| "apps-usb"; |
| |
| wakeup-source; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| status = "disabled"; |
| |
| usb_mp_dwc3: usb@a400000 { |
| compatible = "snps,dwc3"; |
| reg = <0 0x0a400000 0 0xcd00>; |
| |
| interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>; |
| |
| iommus = <&apps_smmu 0x1400 0x0>; |
| |
| phys = <&usb_mp_hsphy0>, <&usb_mp_qmpphy0>, |
| <&usb_mp_hsphy1>, <&usb_mp_qmpphy1>; |
| phy-names = "usb2-0", "usb3-0", |
| "usb2-1", "usb3-1"; |
| dr_mode = "host"; |
| |
| snps,dis_u2_susphy_quirk; |
| snps,dis_enblslpm_quirk; |
| snps,usb3_lpm_capable; |
| |
| dma-coherent; |
| }; |
| }; |
| |
| usb_1_ss0: usb@a6f8800 { |
| compatible = "qcom,x1e80100-dwc3", "qcom,dwc3"; |
| reg = <0 0x0a6f8800 0 0x400>; |
| |
| clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>, |
| <&gcc GCC_USB30_PRIM_MASTER_CLK>, |
| <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>, |
| <&gcc GCC_USB30_PRIM_SLEEP_CLK>, |
| <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, |
| <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>, |
| <&gcc GCC_CFG_NOC_USB_ANOC_NORTH_AHB_CLK>, |
| <&gcc GCC_CFG_NOC_USB_ANOC_SOUTH_AHB_CLK>, |
| <&gcc GCC_SYS_NOC_USB_AXI_CLK>; |
| clock-names = "cfg_noc", |
| "core", |
| "iface", |
| "sleep", |
| "mock_utmi", |
| "noc_aggr", |
| "noc_aggr_north", |
| "noc_aggr_south", |
| "noc_sys"; |
| |
| assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB30_PRIM_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, |
| <200000000>; |
| |
| interrupts-extended = <&intc GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>, |
| <&pdc 61 IRQ_TYPE_EDGE_BOTH>, |
| <&pdc 15 IRQ_TYPE_EDGE_BOTH>, |
| <&pdc 17 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "pwr_event", |
| "dp_hs_phy_irq", |
| "dm_hs_phy_irq", |
| "ss_phy_irq"; |
| |
| power-domains = <&gcc GCC_USB30_PRIM_GDSC>; |
| required-opps = <&rpmhpd_opp_nom>; |
| |
| resets = <&gcc GCC_USB30_PRIM_BCR>; |
| |
| wakeup-source; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| status = "disabled"; |
| |
| usb_1_ss0_dwc3: usb@a600000 { |
| compatible = "snps,dwc3"; |
| reg = <0 0x0a600000 0 0xcd00>; |
| |
| interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; |
| |
| iommus = <&apps_smmu 0x1420 0x0>; |
| |
| phys = <&usb_1_ss0_hsphy>, |
| <&usb_1_ss0_qmpphy QMP_USB43DP_USB3_PHY>; |
| phy-names = "usb2-phy", |
| "usb3-phy"; |
| |
| snps,dis_u2_susphy_quirk; |
| snps,dis_enblslpm_quirk; |
| snps,usb3_lpm_capable; |
| |
| dma-coherent; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| usb_1_ss0_dwc3_hs: endpoint { |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| usb_1_ss0_dwc3_ss: endpoint { |
| remote-endpoint = <&usb_1_ss0_qmpphy_usb_ss_in>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| usb_1_ss1: usb@a8f8800 { |
| compatible = "qcom,x1e80100-dwc3", "qcom,dwc3"; |
| reg = <0 0x0a8f8800 0 0x400>; |
| |
| clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>, |
| <&gcc GCC_USB30_SEC_MASTER_CLK>, |
| <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>, |
| <&gcc GCC_USB30_SEC_SLEEP_CLK>, |
| <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, |
| <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>, |
| <&gcc GCC_AGGRE_NOC_USB_NORTH_AXI_CLK>, |
| <&gcc GCC_AGGRE_NOC_USB_SOUTH_AXI_CLK>, |
| <&gcc GCC_SYS_NOC_USB_AXI_CLK>; |
| clock-names = "cfg_noc", |
| "core", |
| "iface", |
| "sleep", |
| "mock_utmi", |
| "noc_aggr", |
| "noc_aggr_north", |
| "noc_aggr_south", |
| "noc_sys"; |
| |
| assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB30_SEC_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, |
| <200000000>; |
| |
| interrupts-extended = <&intc GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>, |
| <&pdc 60 IRQ_TYPE_EDGE_BOTH>, |
| <&pdc 11 IRQ_TYPE_EDGE_BOTH>, |
| <&pdc 47 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "pwr_event", |
| "dp_hs_phy_irq", |
| "dm_hs_phy_irq", |
| "ss_phy_irq"; |
| |
| power-domains = <&gcc GCC_USB30_SEC_GDSC>; |
| required-opps = <&rpmhpd_opp_nom>; |
| |
| resets = <&gcc GCC_USB30_SEC_BCR>; |
| |
| interconnects = <&usb_south_anoc MASTER_USB3_1 QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS |
| &config_noc SLAVE_USB3_1 QCOM_ICC_TAG_ALWAYS>; |
| interconnect-names = "usb-ddr", |
| "apps-usb"; |
| |
| wakeup-source; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| status = "disabled"; |
| |
| usb_1_ss1_dwc3: usb@a800000 { |
| compatible = "snps,dwc3"; |
| reg = <0 0x0a800000 0 0xcd00>; |
| |
| interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; |
| |
| iommus = <&apps_smmu 0x1460 0x0>; |
| |
| phys = <&usb_1_ss1_hsphy>, |
| <&usb_1_ss1_qmpphy QMP_USB43DP_USB3_PHY>; |
| phy-names = "usb2-phy", |
| "usb3-phy"; |
| |
| snps,dis_u2_susphy_quirk; |
| snps,dis_enblslpm_quirk; |
| snps,usb3_lpm_capable; |
| |
| dma-coherent; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| usb_1_ss1_dwc3_hs: endpoint { |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| usb_1_ss1_dwc3_ss: endpoint { |
| remote-endpoint = <&usb_1_ss1_qmpphy_usb_ss_in>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| mdss: display-subsystem@ae00000 { |
| compatible = "qcom,x1e80100-mdss"; |
| reg = <0 0x0ae00000 0 0x1000>; |
| reg-names = "mdss"; |
| |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&gcc GCC_DISP_HF_AXI_CLK>, |
| <&dispcc DISP_CC_MDSS_MDP_CLK>; |
| |
| resets = <&dispcc DISP_CC_MDSS_CORE_BCR>; |
| |
| interconnects = <&mmss_noc MASTER_MDP QCOM_ICC_TAG_ALWAYS |
| &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>, |
| <&mc_virt MASTER_LLCC QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, |
| <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY |
| &config_noc SLAVE_DISPLAY_CFG QCOM_ICC_TAG_ACTIVE_ONLY>; |
| interconnect-names = "mdp0-mem", |
| "mdp1-mem", |
| "cpu-cfg"; |
| |
| power-domains = <&dispcc MDSS_GDSC>; |
| |
| iommus = <&apps_smmu 0x1c00 0x2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| status = "disabled"; |
| |
| mdss_mdp: display-controller@ae01000 { |
| compatible = "qcom,x1e80100-dpu"; |
| reg = <0 0x0ae01000 0 0x8f000>, |
| <0 0x0aeb0000 0 0x2008>; |
| reg-names = "mdp", |
| "vbif"; |
| |
| interrupts-extended = <&mdss 0>; |
| |
| clocks = <&gcc GCC_DISP_HF_AXI_CLK>, |
| <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, |
| <&dispcc DISP_CC_MDSS_MDP_CLK>, |
| <&dispcc DISP_CC_MDSS_VSYNC_CLK>; |
| clock-names = "nrt_bus", |
| "iface", |
| "lut", |
| "core", |
| "vsync"; |
| |
| operating-points-v2 = <&mdp_opp_table>; |
| |
| power-domains = <&rpmhpd RPMHPD_MMCX>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| mdss_intf0_out: endpoint { |
| remote-endpoint = <&mdss_dp0_in>; |
| }; |
| }; |
| |
| port@4 { |
| reg = <4>; |
| |
| mdss_intf4_out: endpoint { |
| remote-endpoint = <&mdss_dp1_in>; |
| }; |
| }; |
| |
| port@5 { |
| reg = <5>; |
| |
| mdss_intf5_out: endpoint { |
| remote-endpoint = <&mdss_dp3_in>; |
| }; |
| }; |
| |
| port@6 { |
| reg = <6>; |
| |
| mdss_intf6_out: endpoint { |
| remote-endpoint = <&mdss_dp2_in>; |
| }; |
| }; |
| }; |
| |
| mdp_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-200000000 { |
| opp-hz = /bits/ 64 <200000000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-325000000 { |
| opp-hz = /bits/ 64 <325000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| |
| opp-375000000 { |
| opp-hz = /bits/ 64 <375000000>; |
| required-opps = <&rpmhpd_opp_svs_l1>; |
| }; |
| |
| opp-514000000 { |
| opp-hz = /bits/ 64 <514000000>; |
| required-opps = <&rpmhpd_opp_nom>; |
| }; |
| |
| opp-575000000 { |
| opp-hz = /bits/ 64 <575000000>; |
| required-opps = <&rpmhpd_opp_nom_l1>; |
| }; |
| }; |
| }; |
| |
| mdss_dp0: displayport-controller@ae90000 { |
| compatible = "qcom,x1e80100-dp"; |
| reg = <0 0x0ae90000 0 0x200>, |
| <0 0x0ae90200 0 0x200>, |
| <0 0x0ae90400 0 0x600>, |
| <0 0x0ae91000 0 0x400>, |
| <0 0x0ae91400 0 0x400>; |
| |
| interrupts-extended = <&mdss 12>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX0_AUX_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK>; |
| clock-names = "core_iface", |
| "core_aux", |
| "ctrl_link", |
| "ctrl_link_iface", |
| "stream_pixel"; |
| |
| assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>, |
| <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>; |
| assigned-clock-parents = <&usb_1_ss0_qmpphy QMP_USB43DP_DP_LINK_CLK>, |
| <&usb_1_ss0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>; |
| |
| operating-points-v2 = <&mdss_dp0_opp_table>; |
| |
| power-domains = <&rpmhpd RPMHPD_MMCX>; |
| |
| phys = <&usb_1_ss0_qmpphy QMP_USB43DP_DP_PHY>; |
| phy-names = "dp"; |
| |
| #sound-dai-cells = <0>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| mdss_dp0_in: endpoint { |
| remote-endpoint = <&mdss_intf0_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| mdss_dp0_out: endpoint { |
| remote-endpoint = <&usb_1_ss0_qmpphy_dp_in>; |
| }; |
| }; |
| }; |
| |
| mdss_dp0_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-160000000 { |
| opp-hz = /bits/ 64 <160000000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-270000000 { |
| opp-hz = /bits/ 64 <270000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| |
| opp-540000000 { |
| opp-hz = /bits/ 64 <540000000>; |
| required-opps = <&rpmhpd_opp_svs_l1>; |
| }; |
| |
| opp-810000000 { |
| opp-hz = /bits/ 64 <810000000>; |
| required-opps = <&rpmhpd_opp_nom>; |
| }; |
| }; |
| }; |
| |
| mdss_dp1: displayport-controller@ae98000 { |
| compatible = "qcom,x1e80100-dp"; |
| reg = <0 0x0ae98000 0 0x200>, |
| <0 0x0ae98200 0 0x200>, |
| <0 0x0ae98400 0 0x600>, |
| <0 0x0ae99000 0 0x400>, |
| <0 0x0ae99400 0 0x400>; |
| |
| interrupts-extended = <&mdss 13>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX1_AUX_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX1_LINK_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX1_LINK_INTF_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX1_PIXEL0_CLK>; |
| clock-names = "core_iface", |
| "core_aux", |
| "ctrl_link", |
| "ctrl_link_iface", |
| "stream_pixel"; |
| |
| assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX1_LINK_CLK_SRC>, |
| <&dispcc DISP_CC_MDSS_DPTX1_PIXEL0_CLK_SRC>; |
| assigned-clock-parents = <&usb_1_ss1_qmpphy QMP_USB43DP_DP_LINK_CLK>, |
| <&usb_1_ss1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>; |
| |
| operating-points-v2 = <&mdss_dp1_opp_table>; |
| |
| power-domains = <&rpmhpd RPMHPD_MMCX>; |
| |
| phys = <&usb_1_ss1_qmpphy QMP_USB43DP_DP_PHY>; |
| phy-names = "dp"; |
| |
| #sound-dai-cells = <0>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| mdss_dp1_in: endpoint { |
| remote-endpoint = <&mdss_intf4_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| mdss_dp1_out: endpoint { |
| remote-endpoint = <&usb_1_ss1_qmpphy_dp_in>; |
| }; |
| }; |
| }; |
| |
| mdss_dp1_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-160000000 { |
| opp-hz = /bits/ 64 <160000000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-270000000 { |
| opp-hz = /bits/ 64 <270000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| |
| opp-540000000 { |
| opp-hz = /bits/ 64 <540000000>; |
| required-opps = <&rpmhpd_opp_svs_l1>; |
| }; |
| |
| opp-810000000 { |
| opp-hz = /bits/ 64 <810000000>; |
| required-opps = <&rpmhpd_opp_nom>; |
| }; |
| }; |
| }; |
| |
| mdss_dp2: displayport-controller@ae9a000 { |
| compatible = "qcom,x1e80100-dp"; |
| reg = <0 0x0ae9a000 0 0x200>, |
| <0 0x0ae9a200 0 0x200>, |
| <0 0x0ae9a400 0 0x600>, |
| <0 0x0ae9b000 0 0x400>, |
| <0 0x0ae9b400 0 0x400>; |
| |
| interrupts-extended = <&mdss 14>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX2_AUX_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX2_LINK_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX2_PIXEL0_CLK>; |
| clock-names = "core_iface", |
| "core_aux", |
| "ctrl_link", |
| "ctrl_link_iface", |
| "stream_pixel"; |
| |
| assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>, |
| <&dispcc DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>; |
| assigned-clock-parents = <&usb_1_ss2_qmpphy QMP_USB43DP_DP_LINK_CLK>, |
| <&usb_1_ss2_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>; |
| |
| operating-points-v2 = <&mdss_dp2_opp_table>; |
| |
| power-domains = <&rpmhpd RPMHPD_MMCX>; |
| |
| phys = <&usb_1_ss2_qmpphy QMP_USB43DP_DP_PHY>; |
| phy-names = "dp"; |
| |
| #sound-dai-cells = <0>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| mdss_dp2_in: endpoint { |
| remote-endpoint = <&mdss_intf6_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| mdss_dp2_out: endpoint { |
| remote-endpoint = <&usb_1_ss2_qmpphy_dp_in>; |
| }; |
| }; |
| }; |
| |
| mdss_dp2_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-160000000 { |
| opp-hz = /bits/ 64 <160000000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-270000000 { |
| opp-hz = /bits/ 64 <270000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| |
| opp-540000000 { |
| opp-hz = /bits/ 64 <540000000>; |
| required-opps = <&rpmhpd_opp_svs_l1>; |
| }; |
| |
| opp-810000000 { |
| opp-hz = /bits/ 64 <810000000>; |
| required-opps = <&rpmhpd_opp_nom>; |
| }; |
| }; |
| }; |
| |
| mdss_dp3: displayport-controller@aea0000 { |
| compatible = "qcom,x1e80100-dp"; |
| reg = <0 0x0aea0000 0 0x200>, |
| <0 0x0aea0200 0 0x200>, |
| <0 0x0aea0400 0 0x600>, |
| <0 0x0aea1000 0 0x400>, |
| <0 0x0aea1400 0 0x400>; |
| |
| interrupts-extended = <&mdss 15>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX3_AUX_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX3_LINK_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>, |
| <&dispcc DISP_CC_MDSS_DPTX3_PIXEL0_CLK>; |
| clock-names = "core_iface", |
| "core_aux", |
| "ctrl_link", |
| "ctrl_link_iface", |
| "stream_pixel"; |
| |
| assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>, |
| <&dispcc DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>; |
| assigned-clock-parents = <&mdss_dp3_phy 0>, |
| <&mdss_dp3_phy 1>; |
| |
| operating-points-v2 = <&mdss_dp3_opp_table>; |
| |
| power-domains = <&rpmhpd RPMHPD_MMCX>; |
| |
| phys = <&mdss_dp3_phy>; |
| phy-names = "dp"; |
| |
| #sound-dai-cells = <0>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| mdss_dp3_in: endpoint { |
| remote-endpoint = <&mdss_intf5_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| }; |
| }; |
| |
| mdss_dp3_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-160000000 { |
| opp-hz = /bits/ 64 <160000000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-270000000 { |
| opp-hz = /bits/ 64 <270000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| |
| opp-540000000 { |
| opp-hz = /bits/ 64 <540000000>; |
| required-opps = <&rpmhpd_opp_svs_l1>; |
| }; |
| |
| opp-810000000 { |
| opp-hz = /bits/ 64 <810000000>; |
| required-opps = <&rpmhpd_opp_nom>; |
| }; |
| }; |
| }; |
| |
| }; |
| |
| mdss_dp2_phy: phy@aec2a00 { |
| compatible = "qcom,x1e80100-dp-phy"; |
| reg = <0 0x0aec2a00 0 0x19c>, |
| <0 0x0aec2200 0 0xec>, |
| <0 0x0aec2600 0 0xec>, |
| <0 0x0aec2000 0 0x1c8>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_DPTX2_AUX_CLK>, |
| <&dispcc DISP_CC_MDSS_AHB_CLK>; |
| clock-names = "aux", |
| "cfg_ahb"; |
| |
| power-domains = <&rpmhpd RPMHPD_MX>; |
| |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| mdss_dp3_phy: phy@aec5a00 { |
| compatible = "qcom,x1e80100-dp-phy"; |
| reg = <0 0x0aec5a00 0 0x19c>, |
| <0 0x0aec5200 0 0xec>, |
| <0 0x0aec5600 0 0xec>, |
| <0 0x0aec5000 0 0x1c8>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_DPTX3_AUX_CLK>, |
| <&dispcc DISP_CC_MDSS_AHB_CLK>; |
| clock-names = "aux", |
| "cfg_ahb"; |
| |
| power-domains = <&rpmhpd RPMHPD_MX>; |
| |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| dispcc: clock-controller@af00000 { |
| compatible = "qcom,x1e80100-dispcc"; |
| reg = <0 0x0af00000 0 0x20000>; |
| clocks = <&bi_tcxo_div2>, |
| <&bi_tcxo_ao_div2>, |
| <&gcc GCC_DISP_AHB_CLK>, |
| <&sleep_clk>, |
| <0>, /* dsi0 */ |
| <0>, |
| <0>, /* dsi1 */ |
| <0>, |
| <&usb_1_ss0_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp0 */ |
| <&usb_1_ss0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>, |
| <&usb_1_ss1_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp1 */ |
| <&usb_1_ss1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>, |
| <&usb_1_ss2_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp2 */ |
| <&usb_1_ss2_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>, |
| <&mdss_dp3_phy 0>, /* dp3 */ |
| <&mdss_dp3_phy 1>; |
| power-domains = <&rpmhpd RPMHPD_MMCX>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| }; |
| |
| pdc: interrupt-controller@b220000 { |
| compatible = "qcom,x1e80100-pdc", "qcom,pdc"; |
| reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>; |
| |
| qcom,pdc-ranges = <0 480 42>, <42 251 5>, |
| <47 522 52>, <99 609 32>, |
| <131 717 12>, <143 816 19>; |
| #interrupt-cells = <2>; |
| interrupt-parent = <&intc>; |
| interrupt-controller; |
| }; |
| |
| aoss_qmp: power-management@c300000 { |
| compatible = "qcom,x1e80100-aoss-qmp", "qcom,aoss-qmp"; |
| reg = <0 0x0c300000 0 0x400>; |
| interrupt-parent = <&ipcc>; |
| interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP |
| IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>; |
| |
| #clock-cells = <0>; |
| }; |
| |
| sram@c3f0000 { |
| compatible = "qcom,rpmh-stats"; |
| reg = <0 0x0c3f0000 0 0x400>; |
| }; |
| |
| spmi: arbiter@c400000 { |
| compatible = "qcom,x1e80100-spmi-pmic-arb"; |
| reg = <0 0x0c400000 0 0x3000>, |
| <0 0x0c500000 0 0x400000>, |
| <0 0x0c440000 0 0x80000>; |
| reg-names = "core", "chnls", "obsrvr"; |
| |
| qcom,ee = <0>; |
| qcom,channel = <0>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| spmi_bus0: spmi@c42d000 { |
| reg = <0 0x0c42d000 0 0x4000>, |
| <0 0x0c4c0000 0 0x10000>; |
| reg-names = "cnfg", "intr"; |
| |
| interrupt-names = "periph_irq"; |
| interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <4>; |
| |
| #address-cells = <2>; |
| #size-cells = <0>; |
| }; |
| |
| spmi_bus1: spmi@c432000 { |
| reg = <0 0x0c432000 0 0x4000>, |
| <0 0x0c4d0000 0 0x10000>; |
| reg-names = "cnfg", "intr"; |
| |
| interrupt-names = "periph_irq"; |
| interrupts-extended = <&pdc 3 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <4>; |
| |
| #address-cells = <2>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| tlmm: pinctrl@f100000 { |
| compatible = "qcom,x1e80100-tlmm"; |
| reg = <0 0x0f100000 0 0xf00000>; |
| |
| interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| |
| gpio-ranges = <&tlmm 0 0 239>; |
| wakeup-parent = <&pdc>; |
| |
| qup_i2c0_data_clk: qup-i2c0-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio0", "gpio1"; |
| function = "qup0_se0"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c1_data_clk: qup-i2c1-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio4", "gpio5"; |
| function = "qup0_se1"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c2_data_clk: qup-i2c2-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio8", "gpio9"; |
| function = "qup0_se2"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c3_data_clk: qup-i2c3-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio12", "gpio13"; |
| function = "qup0_se3"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c4_data_clk: qup-i2c4-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio16", "gpio17"; |
| function = "qup0_se4"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c5_data_clk: qup-i2c5-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio20", "gpio21"; |
| function = "qup0_se5"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c6_data_clk: qup-i2c6-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio24", "gpio25"; |
| function = "qup0_se6"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c7_data_clk: qup-i2c7-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio14", "gpio15"; |
| function = "qup0_se7"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c8_data_clk: qup-i2c8-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio32", "gpio33"; |
| function = "qup1_se0"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c9_data_clk: qup-i2c9-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio36", "gpio37"; |
| function = "qup1_se1"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c10_data_clk: qup-i2c10-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio40", "gpio41"; |
| function = "qup1_se2"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c11_data_clk: qup-i2c11-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio44", "gpio45"; |
| function = "qup1_se3"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c12_data_clk: qup-i2c12-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio48", "gpio49"; |
| function = "qup1_se4"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c13_data_clk: qup-i2c13-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio52", "gpio53"; |
| function = "qup1_se5"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c14_data_clk: qup-i2c14-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio56", "gpio57"; |
| function = "qup1_se6"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c15_data_clk: qup-i2c15-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio54", "gpio55"; |
| function = "qup1_se7"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c16_data_clk: qup-i2c16-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio64", "gpio65"; |
| function = "qup2_se0"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c17_data_clk: qup-i2c17-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio68", "gpio69"; |
| function = "qup2_se1"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c18_data_clk: qup-i2c18-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio72", "gpio73"; |
| function = "qup2_se2"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c19_data_clk: qup-i2c19-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio76", "gpio77"; |
| function = "qup2_se3"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c20_data_clk: qup-i2c20-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio80", "gpio81"; |
| function = "qup2_se4"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c21_data_clk: qup-i2c21-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio84", "gpio85"; |
| function = "qup2_se5"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c22_data_clk: qup-i2c22-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio88", "gpio89"; |
| function = "qup2_se6"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_i2c23_data_clk: qup-i2c23-data-clk-state { |
| /* SDA, SCL */ |
| pins = "gpio86", "gpio87"; |
| function = "qup2_se7"; |
| drive-strength = <2>; |
| bias-pull-up = <2200>; |
| }; |
| |
| qup_spi0_cs: qup-spi0-cs-state { |
| pins = "gpio3"; |
| function = "qup0_se0"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi0_data_clk: qup-spi0-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio0", "gpio1", "gpio2"; |
| function = "qup0_se0"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi1_cs: qup-spi1-cs-state { |
| pins = "gpio7"; |
| function = "qup0_se1"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi1_data_clk: qup-spi1-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio4", "gpio5", "gpio6"; |
| function = "qup0_se1"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi2_cs: qup-spi2-cs-state { |
| pins = "gpio11"; |
| function = "qup0_se2"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi2_data_clk: qup-spi2-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio8", "gpio9", "gpio10"; |
| function = "qup0_se2"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi3_cs: qup-spi3-cs-state { |
| pins = "gpio15"; |
| function = "qup0_se3"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi3_data_clk: qup-spi3-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio12", "gpio13", "gpio14"; |
| function = "qup0_se3"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi4_cs: qup-spi4-cs-state { |
| pins = "gpio19"; |
| function = "qup0_se4"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi4_data_clk: qup-spi4-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio16", "gpio17", "gpio18"; |
| function = "qup0_se4"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi5_cs: qup-spi5-cs-state { |
| pins = "gpio23"; |
| function = "qup0_se5"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi5_data_clk: qup-spi5-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio20", "gpio21", "gpio22"; |
| function = "qup0_se5"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi6_cs: qup-spi6-cs-state { |
| pins = "gpio27"; |
| function = "qup0_se6"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi6_data_clk: qup-spi6-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio24", "gpio25", "gpio26"; |
| function = "qup0_se6"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi7_cs: qup-spi7-cs-state { |
| pins = "gpio13"; |
| function = "qup0_se7"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi7_data_clk: qup-spi7-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio14", "gpio15", "gpio12"; |
| function = "qup0_se7"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi8_cs: qup-spi8-cs-state { |
| pins = "gpio35"; |
| function = "qup1_se0"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi8_data_clk: qup-spi8-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio32", "gpio33", "gpio34"; |
| function = "qup1_se0"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi9_cs: qup-spi9-cs-state { |
| pins = "gpio39"; |
| function = "qup1_se1"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi9_data_clk: qup-spi9-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio36", "gpio37", "gpio38"; |
| function = "qup1_se1"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi10_cs: qup-spi10-cs-state { |
| pins = "gpio43"; |
| function = "qup1_se2"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi10_data_clk: qup-spi10-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio40", "gpio41", "gpio42"; |
| function = "qup1_se2"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi11_cs: qup-spi11-cs-state { |
| pins = "gpio47"; |
| function = "qup1_se3"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi11_data_clk: qup-spi11-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio44", "gpio45", "gpio46"; |
| function = "qup1_se3"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi12_cs: qup-spi12-cs-state { |
| pins = "gpio51"; |
| function = "qup1_se4"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi12_data_clk: qup-spi12-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio48", "gpio49", "gpio50"; |
| function = "qup1_se4"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi13_cs: qup-spi13-cs-state { |
| pins = "gpio55"; |
| function = "qup1_se5"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi13_data_clk: qup-spi13-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio52", "gpio53", "gpio54"; |
| function = "qup1_se5"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi14_cs: qup-spi14-cs-state { |
| pins = "gpio59"; |
| function = "qup1_se6"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi14_data_clk: qup-spi14-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio56", "gpio57", "gpio58"; |
| function = "qup1_se6"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi15_cs: qup-spi15-cs-state { |
| pins = "gpio53"; |
| function = "qup1_se7"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi15_data_clk: qup-spi15-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio54", "gpio55", "gpio52"; |
| function = "qup1_se7"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi16_cs: qup-spi16-cs-state { |
| pins = "gpio67"; |
| function = "qup2_se0"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi16_data_clk: qup-spi16-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio64", "gpio65", "gpio66"; |
| function = "qup2_se0"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi17_cs: qup-spi17-cs-state { |
| pins = "gpio71"; |
| function = "qup2_se1"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi17_data_clk: qup-spi17-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio68", "gpio69", "gpio70"; |
| function = "qup2_se1"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi18_cs: qup-spi18-cs-state { |
| pins = "gpio75"; |
| function = "qup2_se2"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi18_data_clk: qup-spi18-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio72", "gpio73", "gpio74"; |
| function = "qup2_se2"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi19_cs: qup-spi19-cs-state { |
| pins = "gpio79"; |
| function = "qup2_se3"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi19_data_clk: qup-spi19-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio76", "gpio77", "gpio78"; |
| function = "qup2_se3"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi20_cs: qup-spi20-cs-state { |
| pins = "gpio83"; |
| function = "qup2_se4"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi20_data_clk: qup-spi20-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio80", "gpio81", "gpio82"; |
| function = "qup2_se4"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi21_cs: qup-spi21-cs-state { |
| pins = "gpio87"; |
| function = "qup2_se5"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi21_data_clk: qup-spi21-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio84", "gpio85", "gpio86"; |
| function = "qup2_se5"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi22_cs: qup-spi22-cs-state { |
| pins = "gpio91"; |
| function = "qup2_se6"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi22_data_clk: qup-spi22-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio88", "gpio89", "gpio90"; |
| function = "qup2_se6"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi23_cs: qup-spi23-cs-state { |
| pins = "gpio85"; |
| function = "qup2_se7"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_spi23_data_clk: qup-spi23-data-clk-state { |
| /* MISO, MOSI, CLK */ |
| pins = "gpio86", "gpio87", "gpio84"; |
| function = "qup2_se7"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| qup_uart2_default: qup-uart2-default-state { |
| cts-pins { |
| pins = "gpio8"; |
| function = "qup0_se2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| rts-pins { |
| pins = "gpio9"; |
| function = "qup0_se2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| tx-pins { |
| pins = "gpio10"; |
| function = "qup0_se2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| rx-pins { |
| pins = "gpio11"; |
| function = "qup0_se2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_uart21_default: qup-uart21-default-state { |
| tx-pins { |
| pins = "gpio86"; |
| function = "qup2_se5"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| rx-pins { |
| pins = "gpio87"; |
| function = "qup2_se5"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| }; |
| |
| apps_smmu: iommu@15000000 { |
| compatible = "qcom,x1e80100-smmu-500", "qcom,smmu-500", "arm,mmu-500"; |
| reg = <0 0x15000000 0 0x100000>; |
| |
| interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>; |
| |
| #iommu-cells = <2>; |
| #global-interrupts = <1>; |
| }; |
| |
| intc: interrupt-controller@17000000 { |
| compatible = "arm,gic-v3"; |
| reg = <0 0x17000000 0 0x10000>, /* GICD */ |
| <0 0x17080000 0 0x480000>; /* GICR * 12 */ |
| |
| interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| |
| #redistributor-regions = <1>; |
| redistributor-stride = <0x0 0x40000>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| gic_its: msi-controller@17040000 { |
| compatible = "arm,gic-v3-its"; |
| reg = <0 0x17040000 0 0x40000>; |
| |
| msi-controller; |
| #msi-cells = <1>; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| apps_rsc: rsc@17500000 { |
| compatible = "qcom,rpmh-rsc"; |
| reg = <0 0x17500000 0 0x10000>, |
| <0 0x17510000 0 0x10000>, |
| <0 0x17520000 0 0x10000>; |
| reg-names = "drv-0", "drv-1", "drv-2"; |
| |
| interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,tcs-offset = <0xd00>; |
| qcom,drv-id = <2>; |
| qcom,tcs-config = <ACTIVE_TCS 3>, <SLEEP_TCS 2>, |
| <WAKE_TCS 2>, <CONTROL_TCS 0>; |
| |
| label = "apps_rsc"; |
| power-domains = <&SYSTEM_PD>; |
| |
| apps_bcm_voter: bcm-voter { |
| compatible = "qcom,bcm-voter"; |
| }; |
| |
| rpmhcc: clock-controller { |
| compatible = "qcom,x1e80100-rpmh-clk"; |
| |
| clocks = <&xo_board>; |
| clock-names = "xo"; |
| |
| #clock-cells = <1>; |
| }; |
| |
| rpmhpd: power-controller { |
| compatible = "qcom,x1e80100-rpmhpd"; |
| |
| operating-points-v2 = <&rpmhpd_opp_table>; |
| |
| #power-domain-cells = <1>; |
| |
| rpmhpd_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| rpmhpd_opp_ret: opp-16 { |
| opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; |
| }; |
| |
| rpmhpd_opp_min_svs: opp-48 { |
| opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; |
| }; |
| |
| rpmhpd_opp_low_svs_d2: opp-52 { |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D2>; |
| }; |
| |
| rpmhpd_opp_low_svs_d1: opp-56 { |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>; |
| }; |
| |
| rpmhpd_opp_low_svs_d0: opp-60 { |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D0>; |
| }; |
| |
| rpmhpd_opp_low_svs: opp-64 { |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; |
| }; |
| |
| rpmhpd_opp_low_svs_l1: opp-80 { |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_L1>; |
| }; |
| |
| rpmhpd_opp_svs: opp-128 { |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS>; |
| }; |
| |
| rpmhpd_opp_svs_l0: opp-144 { |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L0>; |
| }; |
| |
| rpmhpd_opp_svs_l1: opp-192 { |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; |
| }; |
| |
| rpmhpd_opp_nom: opp-256 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM>; |
| }; |
| |
| rpmhpd_opp_nom_l1: opp-320 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; |
| }; |
| |
| rpmhpd_opp_nom_l2: opp-336 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>; |
| }; |
| |
| rpmhpd_opp_turbo: opp-384 { |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; |
| }; |
| |
| rpmhpd_opp_turbo_l1: opp-416 { |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; |
| }; |
| }; |
| }; |
| }; |
| |
| timer@17800000 { |
| compatible = "arm,armv7-timer-mem"; |
| reg = <0 0x17800000 0 0x1000>; |
| |
| #address-cells = <2>; |
| #size-cells = <1>; |
| ranges = <0 0 0 0 0x20000000>; |
| |
| frame@17801000 { |
| reg = <0 0x17801000 0x1000>, |
| <0 0x17802000 0x1000>; |
| |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; |
| |
| frame-number = <0>; |
| }; |
| |
| frame@17803000 { |
| reg = <0 0x17803000 0x1000>; |
| |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| |
| frame-number = <1>; |
| |
| status = "disabled"; |
| }; |
| |
| frame@17805000 { |
| reg = <0 0x17805000 0x1000>; |
| |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| |
| frame-number = <2>; |
| |
| status = "disabled"; |
| }; |
| |
| frame@17807000 { |
| reg = <0 0x17807000 0x1000>; |
| |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| |
| frame-number = <3>; |
| |
| status = "disabled"; |
| }; |
| |
| frame@17809000 { |
| reg = <0 0x17809000 0x1000>; |
| |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| |
| frame-number = <4>; |
| |
| status = "disabled"; |
| }; |
| |
| frame@1780b000 { |
| reg = <0 0x1780b000 0x1000>; |
| |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| |
| frame-number = <5>; |
| |
| status = "disabled"; |
| }; |
| |
| frame@1780d000 { |
| reg = <0 0x1780d000 0x1000>; |
| |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| |
| frame-number = <6>; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| pmu@24091000 { |
| compatible = "qcom,x1e80100-llcc-bwmon", "qcom,sc7280-llcc-bwmon"; |
| reg = <0 0x24091000 0 0x1000>; |
| |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; |
| |
| interconnects = <&mc_virt MASTER_LLCC QCOM_ICC_TAG_ACTIVE_ONLY |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ACTIVE_ONLY>; |
| |
| operating-points-v2 = <&llcc_bwmon_opp_table>; |
| |
| llcc_bwmon_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-0 { |
| opp-peak-kBps = <800000>; |
| }; |
| |
| opp-1 { |
| opp-peak-kBps = <2188000>; |
| }; |
| |
| opp-2 { |
| opp-peak-kBps = <3072000>; |
| }; |
| |
| opp-3 { |
| opp-peak-kBps = <6220800>; |
| }; |
| |
| opp-4 { |
| opp-peak-kBps = <6835200>; |
| }; |
| |
| opp-5 { |
| opp-peak-kBps = <8371200>; |
| }; |
| |
| opp-6 { |
| opp-peak-kBps = <10944000>; |
| }; |
| |
| opp-7 { |
| opp-peak-kBps = <12748800>; |
| }; |
| |
| opp-8 { |
| opp-peak-kBps = <14745600>; |
| }; |
| |
| opp-9 { |
| opp-peak-kBps = <16896000>; |
| }; |
| }; |
| }; |
| |
| /* cluster0 */ |
| pmu@240b3400 { |
| compatible = "qcom,x1e80100-cpu-bwmon", "qcom,sdm845-bwmon"; |
| reg = <0 0x240b3400 0 0x600>; |
| |
| interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>; |
| |
| interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY |
| &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ACTIVE_ONLY>; |
| |
| operating-points-v2 = <&cpu_bwmon_opp_table>; |
| |
| cpu_bwmon_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-0 { |
| opp-peak-kBps = <4800000>; |
| }; |
| |
| opp-1 { |
| opp-peak-kBps = <7464000>; |
| }; |
| |
| opp-2 { |
| opp-peak-kBps = <9600000>; |
| }; |
| |
| opp-3 { |
| opp-peak-kBps = <12896000>; |
| }; |
| |
| opp-4 { |
| opp-peak-kBps = <14928000>; |
| }; |
| |
| opp-5 { |
| opp-peak-kBps = <17064000>; |
| }; |
| }; |
| }; |
| |
| /* cluster2 */ |
| pmu@240b5400 { |
| compatible = "qcom,x1e80100-cpu-bwmon", "qcom,sdm845-bwmon"; |
| reg = <0 0x240b5400 0 0x600>; |
| |
| interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>; |
| |
| interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY |
| &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ACTIVE_ONLY>; |
| |
| operating-points-v2 = <&cpu_bwmon_opp_table>; |
| }; |
| |
| /* cluster1 */ |
| pmu@240b6400 { |
| compatible = "qcom,x1e80100-cpu-bwmon", "qcom,sdm845-bwmon"; |
| reg = <0 0x240b6400 0 0x600>; |
| |
| interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>; |
| |
| interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY |
| &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ACTIVE_ONLY>; |
| |
| operating-points-v2 = <&cpu_bwmon_opp_table>; |
| }; |
| |
| system-cache-controller@25000000 { |
| compatible = "qcom,x1e80100-llcc"; |
| reg = <0 0x25000000 0 0x200000>, |
| <0 0x25200000 0 0x200000>, |
| <0 0x25400000 0 0x200000>, |
| <0 0x25600000 0 0x200000>, |
| <0 0x25800000 0 0x200000>, |
| <0 0x25a00000 0 0x200000>, |
| <0 0x25c00000 0 0x200000>, |
| <0 0x25e00000 0 0x200000>, |
| <0 0x26000000 0 0x200000>, |
| <0 0x26200000 0 0x200000>; |
| reg-names = "llcc0_base", |
| "llcc1_base", |
| "llcc2_base", |
| "llcc3_base", |
| "llcc4_base", |
| "llcc5_base", |
| "llcc6_base", |
| "llcc7_base", |
| "llcc_broadcast_base", |
| "llcc_broadcast_and_base"; |
| interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| remoteproc_adsp: remoteproc@30000000 { |
| compatible = "qcom,x1e80100-adsp-pas"; |
| reg = <0 0x30000000 0 0x100>; |
| |
| interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", |
| "fatal", |
| "ready", |
| "handover", |
| "stop-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| power-domains = <&rpmhpd RPMHPD_LCX>, |
| <&rpmhpd RPMHPD_LMX>; |
| power-domain-names = "lcx", |
| "lmx"; |
| |
| interconnects = <&lpass_lpicx_noc MASTER_LPASS_PROC QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| |
| memory-region = <&adspslpi_mem>, |
| <&q6_adsp_dtb_mem>; |
| |
| qcom,qmp = <&aoss_qmp>; |
| |
| qcom,smem-states = <&smp2p_adsp_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts-extended = <&ipcc IPCC_CLIENT_LPASS |
| IPCC_MPROC_SIGNAL_GLINK_QMP |
| IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&ipcc IPCC_CLIENT_LPASS |
| IPCC_MPROC_SIGNAL_GLINK_QMP>; |
| |
| label = "lpass"; |
| qcom,remote-pid = <2>; |
| |
| fastrpc { |
| compatible = "qcom,fastrpc"; |
| qcom,glink-channels = "fastrpcglink-apps-dsp"; |
| label = "adsp"; |
| qcom,non-secure-domain; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| compute-cb@3 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <3>; |
| iommus = <&apps_smmu 0x1003 0x80>, |
| <&apps_smmu 0x1063 0x0>; |
| dma-coherent; |
| }; |
| |
| compute-cb@4 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <4>; |
| iommus = <&apps_smmu 0x1004 0x80>, |
| <&apps_smmu 0x1064 0x0>; |
| dma-coherent; |
| }; |
| |
| compute-cb@5 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <5>; |
| iommus = <&apps_smmu 0x1005 0x80>, |
| <&apps_smmu 0x1065 0x0>; |
| dma-coherent; |
| }; |
| |
| compute-cb@6 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <6>; |
| iommus = <&apps_smmu 0x1006 0x80>, |
| <&apps_smmu 0x1066 0x0>; |
| dma-coherent; |
| }; |
| |
| compute-cb@7 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <7>; |
| iommus = <&apps_smmu 0x1007 0x80>, |
| <&apps_smmu 0x1067 0x0>; |
| dma-coherent; |
| }; |
| }; |
| |
| gpr { |
| compatible = "qcom,gpr"; |
| qcom,glink-channels = "adsp_apps"; |
| qcom,domain = <GPR_DOMAIN_ID_ADSP>; |
| qcom,intents = <512 20>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| q6apm: service@1 { |
| compatible = "qcom,q6apm"; |
| reg = <GPR_APM_MODULE_IID>; |
| #sound-dai-cells = <0>; |
| qcom,protection-domain = "avs/audio", |
| "msm/adsp/audio_pd"; |
| |
| q6apmbedai: bedais { |
| compatible = "qcom,q6apm-lpass-dais"; |
| #sound-dai-cells = <1>; |
| }; |
| |
| q6apmdai: dais { |
| compatible = "qcom,q6apm-dais"; |
| iommus = <&apps_smmu 0x1001 0x80>, |
| <&apps_smmu 0x1061 0x0>; |
| }; |
| }; |
| |
| q6prm: service@2 { |
| compatible = "qcom,q6prm"; |
| reg = <GPR_PRM_MODULE_IID>; |
| qcom,protection-domain = "avs/audio", |
| "msm/adsp/audio_pd"; |
| |
| q6prmcc: clock-controller { |
| compatible = "qcom,q6prm-lpass-clocks"; |
| #clock-cells = <2>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| remoteproc_cdsp: remoteproc@32300000 { |
| compatible = "qcom,x1e80100-cdsp-pas"; |
| reg = <0 0x32300000 0 0x1400000>; |
| |
| interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", |
| "fatal", |
| "ready", |
| "handover", |
| "stop-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| power-domains = <&rpmhpd RPMHPD_CX>, |
| <&rpmhpd RPMHPD_MXC>, |
| <&rpmhpd RPMHPD_NSP>; |
| power-domain-names = "cx", |
| "mxc", |
| "nsp"; |
| |
| interconnects = <&nsp_noc MASTER_CDSP_PROC QCOM_ICC_TAG_ALWAYS |
| &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; |
| |
| memory-region = <&cdsp_mem>, |
| <&q6_cdsp_dtb_mem>; |
| |
| qcom,qmp = <&aoss_qmp>; |
| |
| qcom,smem-states = <&smp2p_cdsp_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts-extended = <&ipcc IPCC_CLIENT_CDSP |
| IPCC_MPROC_SIGNAL_GLINK_QMP |
| IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&ipcc IPCC_CLIENT_CDSP |
| IPCC_MPROC_SIGNAL_GLINK_QMP>; |
| |
| label = "cdsp"; |
| qcom,remote-pid = <5>; |
| |
| fastrpc { |
| compatible = "qcom,fastrpc"; |
| qcom,glink-channels = "fastrpcglink-apps-dsp"; |
| label = "cdsp"; |
| qcom,non-secure-domain; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| compute-cb@1 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <1>; |
| iommus = <&apps_smmu 0x0c01 0x20>; |
| dma-coherent; |
| }; |
| |
| compute-cb@2 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <2>; |
| iommus = <&apps_smmu 0x0c02 0x20>; |
| dma-coherent; |
| }; |
| |
| compute-cb@3 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <3>; |
| iommus = <&apps_smmu 0x0c03 0x20>; |
| dma-coherent; |
| }; |
| |
| compute-cb@4 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <4>; |
| iommus = <&apps_smmu 0x0c04 0x20>; |
| dma-coherent; |
| }; |
| |
| compute-cb@5 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <5>; |
| iommus = <&apps_smmu 0x0c05 0x20>; |
| dma-coherent; |
| }; |
| |
| compute-cb@6 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <6>; |
| iommus = <&apps_smmu 0x0c06 0x20>; |
| dma-coherent; |
| }; |
| |
| compute-cb@7 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <7>; |
| iommus = <&apps_smmu 0x0c07 0x20>; |
| dma-coherent; |
| }; |
| |
| compute-cb@8 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <8>; |
| iommus = <&apps_smmu 0x0c08 0x20>; |
| dma-coherent; |
| }; |
| |
| /* note: compute-cb@9 is secure */ |
| |
| compute-cb@10 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <10>; |
| iommus = <&apps_smmu 0x0c0c 0x20>; |
| dma-coherent; |
| }; |
| |
| compute-cb@11 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <11>; |
| iommus = <&apps_smmu 0x0c0d 0x20>; |
| dma-coherent; |
| }; |
| |
| compute-cb@12 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <12>; |
| iommus = <&apps_smmu 0x0c0e 0x20>; |
| dma-coherent; |
| }; |
| |
| compute-cb@13 { |
| compatible = "qcom,fastrpc-compute-cb"; |
| reg = <13>; |
| iommus = <&apps_smmu 0x0c0f 0x20>; |
| dma-coherent; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| |
| interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, |
| <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| |
| thermal-zones { |
| aoss0-thermal { |
| thermal-sensors = <&tsens0 0>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| aoss0-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu0-0-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens0 1>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu0-0-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens0 2>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu0-1-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens0 3>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu0-1-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens0 4>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu0-2-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens0 5>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu0-2-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens0 6>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu0-3-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens0 7>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu0-3-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens0 8>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpuss0-top-thermal { |
| thermal-sensors = <&tsens0 9>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| cpuss2-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpuss0-btm-thermal { |
| thermal-sensors = <&tsens0 10>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| cpuss2-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| mem-thermal { |
| thermal-sensors = <&tsens0 11>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| mem-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| video-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens0 12>; |
| |
| trips { |
| trip-point0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| aoss1-thermal { |
| thermal-sensors = <&tsens1 0>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| aoss0-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu1-0-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens1 1>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu1-0-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens1 2>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu1-1-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens1 3>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu1-1-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens1 4>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu1-2-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens1 5>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu1-2-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens1 6>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu1-3-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens1 7>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu1-3-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens1 8>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpuss1-top-thermal { |
| thermal-sensors = <&tsens1 9>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| cpuss2-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpuss1-btm-thermal { |
| thermal-sensors = <&tsens1 10>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| cpuss2-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| aoss2-thermal { |
| thermal-sensors = <&tsens2 0>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| aoss0-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu2-0-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens2 1>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu2-0-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens2 2>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu2-1-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens2 3>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu2-1-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens2 4>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu2-2-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens2 5>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu2-2-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens2 6>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu2-3-top-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens2 7>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu2-3-btm-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens2 8>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu-critical { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpuss2-top-thermal { |
| thermal-sensors = <&tsens2 9>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| cpuss2-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpuss2-btm-thermal { |
| thermal-sensors = <&tsens2 10>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| cpuss2-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| aoss3-thermal { |
| thermal-sensors = <&tsens3 0>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| aoss0-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| nsp0-thermal { |
| thermal-sensors = <&tsens3 1>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| nsp0-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| nsp1-thermal { |
| thermal-sensors = <&tsens3 2>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| nsp1-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| nsp2-thermal { |
| thermal-sensors = <&tsens3 3>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| nsp2-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| nsp3-thermal { |
| thermal-sensors = <&tsens3 4>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| nsp3-critical { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpuss-0-thermal { |
| polling-delay-passive = <10>; |
| |
| thermal-sensors = <&tsens3 5>; |
| |
| trips { |
| trip-point0 { |
| temperature = <85000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <90000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| |
| trip-point2 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpuss-1-thermal { |
| polling-delay-passive = <10>; |
| |
| thermal-sensors = <&tsens3 6>; |
| |
| trips { |
| trip-point0 { |
| temperature = <85000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <90000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| |
| trip-point2 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpuss-2-thermal { |
| polling-delay-passive = <10>; |
| |
| thermal-sensors = <&tsens3 7>; |
| |
| trips { |
| trip-point0 { |
| temperature = <85000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <90000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| |
| trip-point2 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpuss-3-thermal { |
| polling-delay-passive = <10>; |
| |
| thermal-sensors = <&tsens3 8>; |
| |
| trips { |
| trip-point0 { |
| temperature = <85000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <90000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| |
| trip-point2 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpuss-4-thermal { |
| polling-delay-passive = <10>; |
| |
| thermal-sensors = <&tsens3 9>; |
| |
| trips { |
| trip-point0 { |
| temperature = <85000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <90000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| |
| trip-point2 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpuss-5-thermal { |
| polling-delay-passive = <10>; |
| |
| thermal-sensors = <&tsens3 10>; |
| |
| trips { |
| trip-point0 { |
| temperature = <85000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <90000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| |
| trip-point2 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpuss-6-thermal { |
| polling-delay-passive = <10>; |
| |
| thermal-sensors = <&tsens3 11>; |
| |
| trips { |
| trip-point0 { |
| temperature = <85000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <90000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| |
| trip-point2 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpuss-7-thermal { |
| polling-delay-passive = <10>; |
| |
| thermal-sensors = <&tsens3 12>; |
| |
| trips { |
| trip-point0 { |
| temperature = <85000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <90000>; |
| hysteresis = <1000>; |
| type = "hot"; |
| }; |
| |
| trip-point2 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| camera0-thermal { |
| thermal-sensors = <&tsens3 13>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| camera0-critical { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| camera1-thermal { |
| thermal-sensors = <&tsens3 14>; |
| |
| trips { |
| trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| |
| camera0-critical { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| }; |